Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Errata] [Info page]
INFORMATIONAL
Errata ExistInternet Engineering Task Force (IETF) G. Fairhurst, Ed.Request for Comments: 8095 University of AberdeenCategory: Informational B. Trammell, Ed.ISSN: 2070-1721 M. Kuehlewind, Ed. ETH Zurich March 2017Services Provided byIETF Transport Protocols and Congestion Control MechanismsAbstract This document describes, surveys, and classifies the protocol mechanisms provided by existing IETF protocols, as background for determining a common set of transport services. It examines the Transmission Control Protocol (TCP), Multipath TCP, the Stream Control Transmission Protocol (SCTP), the User Datagram Protocol (UDP), UDP-Lite, the Datagram Congestion Control Protocol (DCCP), the Internet Control Message Protocol (ICMP), the Real-Time Transport Protocol (RTP), File Delivery over Unidirectional Transport / Asynchronous Layered Coding (FLUTE/ALC) for Reliable Multicast, NACK- Oriented Reliable Multicast (NORM), Transport Layer Security (TLS), Datagram TLS (DTLS), and the Hypertext Transport Protocol (HTTP), when HTTP is used as a pseudotransport. This survey provides background for the definition of transport services within the TAPS working group.Status of This Memo This document is not an Internet Standards Track specification; it is published for informational purposes. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Not all documents approved by the IESG are a candidate for any level of Internet Standard; seeSection 2 of RFC 7841. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained athttp://www.rfc-editor.org/info/rfc8095.Fairhurst, et al. Informational [Page 1]
RFC 8095 Transport Services March 2017Copyright Notice Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject toBCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.Table of Contents1. Introduction ....................................................41.1. Overview of Transport Features .............................42. Terminology .....................................................53. Existing Transport Protocols ....................................63.1. Transport Control Protocol (TCP) ...........................63.1.1. Protocol Description ................................63.1.2. Interface Description ...............................83.1.3. Transport Features ..................................93.2. Multipath TCP (MPTCP) .....................................103.2.1. Protocol Description ...............................103.2.2. Interface Description ..............................103.2.3. Transport Features .................................113.3. User Datagram Protocol (UDP) ..............................113.3.1. Protocol Description ...............................113.3.2. Interface Description ..............................123.3.3. Transport Features .................................133.4. Lightweight User Datagram Protocol (UDP-Lite) .............133.4.1. Protocol Description ...............................133.4.2. Interface Description ..............................143.4.3. Transport Features .................................143.5. Stream Control Transmission Protocol (SCTP) ...............143.5.1. Protocol Description ...............................153.5.2. Interface Description ..............................173.5.3. Transport Features .................................193.6. Datagram Congestion Control Protocol (DCCP) ...............203.6.1. Protocol Description ...............................213.6.2. Interface Description ..............................223.6.3. Transport Features .................................22Fairhurst, et al. Informational [Page 2]
RFC 8095 Transport Services March 2017 3.7. Transport Layer Security (TLS) and Datagram TLS (DTLS) as a Pseudotransport ...............................233.7.1. Protocol Description ...............................233.7.2. Interface Description ..............................243.7.3. Transport Features .................................253.8. Real-Time Transport Protocol (RTP) ........................263.8.1. Protocol Description ...............................263.8.2. Interface Description ..............................273.8.3. Transport Features .................................27 3.9. Hypertext Transport Protocol (HTTP) over TCP as a Pseudotransport ...........................................283.9.1. Protocol Description ...............................283.9.2. Interface Description ..............................293.9.3. Transport Features .................................30 3.10. File Delivery over Unidirectional Transport / Asynchronous Layered Coding (FLUTE/ALC) for Reliable Multicast .......................................313.10.1. Protocol Description ..............................313.10.2. Interface Description .............................333.10.3. Transport Features ................................333.11. NACK-Oriented Reliable Multicast (NORM) ..................343.11.1. Protocol Description ..............................343.11.2. Interface Description .............................353.11.3. Transport Features ................................363.12. Internet Control Message Protocol (ICMP) .................363.12.1. Protocol Description ..............................373.12.2. Interface Description .............................373.12.3. Transport Features ................................384. Congestion Control .............................................385. Transport Features .............................................396. IANA Considerations ............................................427. Security Considerations ........................................428. Informative References .........................................42 Acknowledgments ...................................................53 Contributors ......................................................53 Authors' Addresses ................................................54Fairhurst, et al. Informational [Page 3]
RFC 8095 Transport Services March 20171. Introduction Internet applications make use of the services provided by a transport protocol, such as TCP (a reliable, in-order stream protocol) or UDP (an unreliable datagram protocol). We use the term "transport service" to mean the end-to-end service provided to an application by the transport layer. That service can only be provided correctly if information about the intended usage is supplied from the application. The application may determine this information at design time, compile time, or run time, and may include guidance on whether a feature is required, a preference by the application, or something in between. Examples of features of transport services are reliable delivery, ordered delivery, content privacy to in-path devices, and integrity protection. The IETF has defined a wide variety of transport protocols beyond TCP and UDP, including SCTP, DCCP, MPTCP, and UDP-Lite. Transport services may be provided directly by these transport protocols or layered on top of them using protocols such as WebSockets (which runs over TCP), RTP (over TCP or UDP) or WebRTC data channels (which run over SCTP over DTLS over UDP or TCP). Services built on top of UDP or UDP-Lite typically also need to specify additional mechanisms, including a congestion control mechanism (such as NewReno [RFC6582], TCP-Friendly Rate Control (TFRC) [RFC5348], or Low Extra Delay Background Transport (LEDBAT) [RFC6817]). This extends the set of available transport services beyond those provided to applications by TCP and UDP. The transport protocols described in this document provide a basis for the definition of transport services provided by common protocols, as background for the TAPS working group. The protocols listed here were chosen to help expose as many potential transport services as possible and are not meant to be a comprehensive survey or classification of all transport protocols.1.1. Overview of Transport Features Transport protocols can be differentiated by the features of the services they provide. Some of these provided features are closely related to basic control function that a protocol needs to work over a network path, such as addressing. The number of participants in a given association also determines its applicability: a connection can be between endpoints (unicast), to one of multiple endpoints (anycast), or simultaneously to multiple endpoints (multicast). Unicast protocols usually support bidirectional communication, while multicast is generallyFairhurst, et al. Informational [Page 4]
RFC 8095 Transport Services March 2017 unidirectional. Another feature is whether a transport requires a control exchange across the network at setup (e.g., TCP) or whether it is connectionless (e.g., UDP). For packet delivery itself, reliability and integrity protection, ordering, and framing are basic features. However, these features are implemented with different levels of assurance in different protocols. As an example, a transport service may provide full reliability, with detection of loss and retransmission (e.g., TCP). SCTP offers a message-based service that can provide full or partial reliability and allows the protocol to minimize the head-of-line blocking due to the support of ordered and unordered message delivery within multiple streams. UDP-Lite and DCCP can provide partial integrity protection to enable corruption tolerance. Usually, a protocol has been designed to support one specific type of delivery/framing: either data needs to be divided into transmission units based on network packets (datagram service) or a data stream is segmented and re-combined across multiple packets (stream service). Whole objects such as files are handled accordingly. This decision strongly influences the interface that is provided to the upper layer. In addition, transport protocols offer a certain support for transmission control. For example, a transport service can provide flow control to allow a receiver to regulate the transmission rate of a sender. Further, a transport service can provide congestion control (seeSection 4). As an example, TCP and SCTP provide congestion control for use in the Internet, whereas UDP leaves this function to the upper-layer protocol that uses UDP. Security features are often provided independently of the transport protocol, via Transport Layer Security (TLS) (seeSection 3.7) or by the application-layer protocol itself. The security properties TLS provides to the application (such as confidentiality, integrity, and authenticity) are also features of the transport layer, even though they are often presently implemented in a separate protocol.2. Terminology The following terms are used throughout this document and in subsequent documents produced by the TAPS working group that describe the composition and decomposition of transport services. Transport Feature: a specific end-to-end feature that the transport layer provides to an application. Examples include confidentiality, reliable delivery, ordered delivery, message- versus-stream orientation, etc.Fairhurst, et al. Informational [Page 5]
RFC 8095 Transport Services March 2017 Transport Service: a set of transport features, without an association to any given framing protocol, that provides a complete service to an application. Transport Protocol: an implementation that provides one or more different transport services using a specific framing and header format on the wire. Application: an entity that uses the transport layer for end-to-end delivery data across the network (this may also be an upper-layer protocol or tunnel encapsulation).3. Existing Transport Protocols This section provides a list of known IETF transport protocols and transport protocol frameworks. It does not make an assessment about whether specific implementations of protocols are fully compliant to current IETF specifications.3.1. Transport Control Protocol (TCP) TCP is an IETF Standards Track transport protocol. [RFC793] introduces TCP as follows: The Transmission Control Protocol (TCP) is intended for use as a highly reliable host-to-host protocol between hosts in packet- switched computer communication networks, and in interconnected systems of such networks. Since its introduction, TCP has become the default connection- oriented, stream-based transport protocol in the Internet. It is widely implemented by endpoints and widely used by common applications.3.1.1. Protocol Description TCP is a connection-oriented protocol that provides a three-way handshake to allow a client and server to set up a connection and negotiate features and provides mechanisms for orderly completion and immediate teardown of a connection [RFC793] [TCP-SPEC]. TCP is defined by a family of RFCs (see [RFC7414]). TCP provides multiplexing to multiple sockets on each host using port numbers. A similar approach is adopted by other IETF-defined transports. An active TCP session is identified by its four-tuple of local and remote IP addresses and local and remote port numbers. The destination port during connection setup is often used to indicate the requested service.Fairhurst, et al. Informational [Page 6]
RFC 8095 Transport Services March 2017 TCP partitions a continuous stream of bytes into segments, sized to fit in IP packets based on a negotiated maximum segment size and further constrained by the effective Maximum Transmission Unit (MTU) from Path MTU Discovery (PMTUD). ICMP-based PMTUD [RFC1191] [RFC1981] as well as Packetization Layer PMTUD (PLPMTUD) [RFC4821] have been defined by the IETF. Each byte in the stream is identified by a sequence number. The sequence number is used to order segments on receipt, to identify segments in acknowledgments, and to detect unacknowledged segments for retransmission. This is the basis of the reliable, ordered delivery of data in a TCP stream. TCP Selective Acknowledgment (SACK) [RFC2018] extends this mechanism by making it possible to provide earlier identification of which segments are missing, allowing faster retransmission. SACK-based methods (e.g., Duplicate Selective ACK) can also result in less spurious retransmission. Receiver flow control is provided by a sliding window, which limits the amount of unacknowledged data that can be outstanding at a given time. The window scale option [RFC7323] allows a receiver to use windows greater than 64 KB. All TCP senders provide congestion control, such as that described in [RFC5681]. TCP uses a sequence number with a sliding receiver window for flow control. The TCP congestion control mechanism also utilizes this TCP sequence number to manage a separate congestion window [RFC5681]. The sending window at a given point in time is the minimum of the receiver window and the congestion window. The congestion window is increased in the absence of congestion and decreased if congestion is detected. Often, loss is implicitly handled as a congestion indication, which is detected in TCP (also as input for retransmission handling) based on two mechanisms: a retransmission timer with exponential back-off or the reception of three acknowledgments for the same segment, so called "duplicated ACKs" (fast retransmit). In addition, Explicit Congestion Notification (ECN) [RFC3168] can be used in TCP and, if supported by both endpoints, allows a network node to signal congestion without inducing loss. Alternatively, a delay-based congestion control scheme that reacts to changes in delay as an early indication of congestion can be used in TCP. This is further described inSection 4. Examples of different kinds of congestion control schemes are provided inSection 4. TCP protocol instances can be extended (see [RFC7414]). Some protocol features may also be tuned to optimize for a specific deployment scenario. Some features are sender-side only, requiring no negotiation with the receiver; some are receiver-side only; and some are explicitly negotiated during connection setup.Fairhurst, et al. Informational [Page 7]
RFC 8095 Transport Services March 2017 TCP may buffer data, e.g., to optimize processing or capacity usage. TCP therefore provides mechanisms to control this, including an optional "PUSH" function [RFC793] that explicitly requests the transport service not to delay data. By default, TCP segment partitioning uses Nagle's algorithm [TCP-SPEC] to buffer data at the sender into large segments, potentially incurring sender-side buffering delay; this algorithm can be disabled by the sender to transmit more immediately, e.g., to reduce latency for interactive sessions. TCP provides an "urgent data" function for limited out-of-order delivery of the data. This function is deprecated [RFC6093]. A TCP Reset (RST) control message may be used to force a TCP endpoint to close a session [RFC793], aborting the connection. A mandatory checksum provides a basic integrity check against misdelivery and data corruption over the entire packet. Applications that require end-to-end integrity of data are recommended to include a stronger integrity check of their payload data. The TCP checksum [RFC1071] [RFC2460] does not support partial payload protection (as in DCCP/UDP-Lite). TCP supports only unicast connections.3.1.2. Interface Description The User/TCP Interface defined in [RFC793] provides six user commands: Open, Send, Receive, Close, Status, and Abort. This interface does not describe configuration of TCP options or parameters aside from the use of the PUSH and URGENT flags. [RFC1122] describes extensions of the TCP/application-layer interface for: o reporting soft errors such as reception of ICMP error messages, extensive retransmission, or urgent pointer advance, o providing a possibility to specify the Differentiated Services Code Point (DSCP) [RFC3260] (formerly, the Type-of-Service (TOS)) for segments, o providing a flush call to empty the TCP send queue, and o multihoming support.Fairhurst, et al. Informational [Page 8]
RFC 8095 Transport Services March 2017 In API implementations derived from the BSD Sockets API, TCP sockets are created using the "SOCK_STREAM" socket type as described in the IEEE Portable Operating System Interface (POSIX) Base Specifications [POSIX]. The features used by a protocol instance may be set and tuned via this API. There are currently no documents in the RFC Series that describe this interface.3.1.3. Transport Features The transport features provided by TCP are: o connection-oriented transport with feature negotiation and application-to-port mapping (implemented using SYN segments and the TCP Option field to negotiate features), o unicast transport (though anycast TCP is implemented, at risk of instability due to rerouting), o port multiplexing, o unidirectional or bidirectional communication, o stream-oriented delivery in a single stream, o fully reliable delivery (implemented using ACKs sent from the receiver to confirm delivery), o error detection (implemented using a segment checksum to verify delivery to the correct endpoint and integrity of the data and options), o segmentation, o data bundling (optional; uses Nagle's algorithm to coalesce data sent within the same RTT into full-sized segments), o flow control (implemented using a window-based mechanism where the receiver advertises the window that it is willing to buffer), and o congestion control (usually implemented using a window-based mechanism and four algorithms for different phases of the transmission: slow start, congestion avoidance, fast retransmit, and fast recovery [RFC5681]).Fairhurst, et al. Informational [Page 9]
RFC 8095 Transport Services March 20173.2. Multipath TCP (MPTCP) Multipath TCP [RFC6824] is an extension for TCP to support multihoming for resilience, mobility, and load balancing. It is designed to be as indistinguishable to middleboxes from non-multipath TCP as possible. It does so by establishing regular TCP flows between a pair of source/destination endpoints and multiplexing the application's stream over these flows. Sub-flows can be started over IPv4 or IPv6 for the same session.3.2.1. Protocol Description MPTCP uses TCP options for its control plane. They are used to signal multipath capabilities, as well as to negotiate data sequence numbers, advertise other available IP addresses, and establish new sessions between pairs of endpoints. By multiplexing one byte stream over separate paths, MPTCP can achieve a higher throughput than TCP in certain situations. However, if coupled congestion control [RFC6356] is used, it might limit this benefit to maintain fairness to other flows at the bottleneck. When aggregating capacity over multiple paths, and depending on the way packets are scheduled on each TCP subflow, additional delay and higher jitter might be observed before in-order delivery of data to the applications.3.2.2. Interface Description By default, MPTCP exposes the same interface as TCP to the application. [RFC6897], however, describes a richer API for MPTCP- aware applications. This Basic API describes how an application can: o enable or disable MPTCP. o bind a socket to one or more selected local endpoints. o query local and remote endpoint addresses. o get a unique connection identifier (similar to an address-port pair for TCP). The document also recommends the use of extensions defined for SCTP [RFC6458] (seeSection 3.5) to support multihoming for resilience and mobility.Fairhurst, et al. Informational [Page 10]
RFC 8095 Transport Services March 20173.2.3. Transport Features As an extension to TCP, MPTCP provides mostly the same features. By establishing multiple sessions between available endpoints, it can additionally provide soft failover solutions in the case that one of the paths becomes unusable. Therefore, the transport features provided by MPTCP in addition to TCP are: o multihoming for load balancing, with endpoint multiplexing of a single byte stream, using either coupled congestion control or throughput maximization, o address family multiplexing (using IPv4 and IPv6 for the same session), and o resilience to network failure and/or handover.3.3. User Datagram Protocol (UDP) The User Datagram Protocol (UDP) [RFC768] [RFC2460] is an IETF Standards Track transport protocol. It provides a unidirectional datagram protocol that preserves message boundaries. It provides no error correction, congestion control, or flow control. It can be used to send broadcast datagrams (IPv4) or multicast datagrams (IPv4 and IPv6), in addition to unicast and anycast datagrams. IETF guidance on the use of UDP is provided in [RFC8085]. UDP is widely implemented and widely used by common applications, including DNS.3.3.1. Protocol Description UDP is a connectionless protocol that maintains message boundaries, with no connection setup or feature negotiation. The protocol uses independent messages, ordinarily called "datagrams". It provides detection of payload errors and misdelivery of packets to an unintended endpoint, both of which result in discard of received datagrams, with no indication to the user of the service. It is possible to create IPv4 UDP datagrams with no checksum, and while this is generally discouraged [RFC1122] [RFC8085], certain special cases permit this use. These datagrams rely on the IPv4 header checksum to protect from misdelivery to an unintended endpoint. IPv6 does not permit UDP datagrams with no checksum, although in certain cases [RFC6936], this rule may be relaxed [RFC6935].Fairhurst, et al. Informational [Page 11]
RFC 8095 Transport Services March 2017 UDP does not provide reliability and does not provide retransmission. Messages may be reordered, lost, or duplicated in transit. Note that due to the relatively weak form of checksum used by UDP, applications that require end-to-end integrity of data are recommended to include a stronger integrity check of their payload data. Because UDP provides no flow control, a receiving application that is unable to run sufficiently fast, or frequently, may miss messages. The lack of congestion handling implies UDP traffic may experience loss when using an overloaded path and may cause the loss of messages from other protocols (e.g., TCP) when sharing the same network path. On transmission, UDP encapsulates each datagram into a single IP packet or several IP packet fragments. This allows a datagram to be larger than the effective path MTU. Fragments are reassembled before delivery to the UDP receiver, making this transparent to the user of the transport service. When jumbograms are supported, larger messages may be sent without performing fragmentation. UDP on its own does not provide support for segmentation, receiver flow control, congestion control, PMTUD/PLPMTUD, or ECN. Applications that require these features need to provide them on their own or use a protocol over UDP that provides them [RFC8085].3.3.2. Interface Description [RFC768] describes basic requirements for an API for UDP. Guidance on the use of common APIs is provided in [RFC8085]. A UDP endpoint consists of a tuple of (IP address, port number). De-multiplexing using multiple abstract endpoints (sockets) on the same IP address is supported. The same socket may be used by a single server to interact with multiple clients. (Note: This behavior differs from TCP, which uses a pair of tuples to identify a connection). Multiple server instances (processes) that bind to the same socket can cooperate to service multiple clients. The socket implementation arranges to not duplicate the same received unicast message to multiple server processes. Many operating systems also allow a UDP socket to be "connected", i.e., to bind a UDP socket to a specific (remote) UDP endpoint. Unlike TCP's connect primitive, for UDP, this is only a local operation that serves to simplify the local send/receive functions and to filter the traffic for the specified addresses and ports [RFC8085].Fairhurst, et al. Informational [Page 12]
RFC 8095 Transport Services March 20173.3.3. Transport Features The transport features provided by UDP are: o unicast, multicast, anycast, or IPv4 broadcast transport, o port multiplexing (where a receiving port can be configured to receive datagrams from multiple senders), o message-oriented delivery, o unidirectional or bidirectional communication where the transmissions in each direction are independent, o non-reliable delivery, o unordered delivery, and o error detection (implemented using a segment checksum to verify delivery to the correct endpoint and integrity of the data; optional for IPv4 and optional under specific conditions for IPv6 where all or none of the payload data is protected).3.4. Lightweight User Datagram Protocol (UDP-Lite) The Lightweight User Datagram Protocol (UDP-Lite) [RFC3828] is an IETF Standards Track transport protocol. It provides a unidirectional, datagram protocol that preserves message boundaries. IETF guidance on the use of UDP-Lite is provided in [RFC8085]. A UDP-Lite service may support IPv4 broadcast, multicast, anycast, and unicast, as well as IPv6 multicast, anycast, and unicast. Examples of use include a class of applications that can derive benefit from having partially damaged payloads delivered rather than discarded. One use is to provide header integrity checks but allow delivery of corrupted payloads to error-tolerant applications or to applications that use some other mechanism to provide payload integrity (see [RFC6936]).3.4.1. Protocol Description Like UDP, UDP-Lite is a connectionless datagram protocol, with no connection setup or feature negotiation. It changes the semantics of the UDP Payload Length field to that of a Checksum Coverage Length field and is identified by a different IP protocol/next-header value. The Checksum Coverage Length field specifies the intended checksum coverage, with the remaining unprotected part of the payload calledFairhurst, et al. Informational [Page 13]
RFC 8095 Transport Services March 2017 the "error-insensitive part". Therefore, applications using UDP-Lite cannot make assumptions regarding the correctness of the data received in the insensitive part of the UDP-Lite payload. Otherwise, UDP-Lite is semantically identical to UDP. In the same way as for UDP, mechanisms for receiver flow control, congestion control, PMTU or PLPMTU discovery, support for ECN, etc., need to be provided by upper-layer protocols [RFC8085].3.4.2. Interface Description There is no API currently specified in the RFC Series, but guidance on use of common APIs is provided in [RFC8085]. The interface of UDP-Lite differs from that of UDP by the addition of a single (socket) option that communicates a checksum coverage length value. The checksum coverage may also be made visible to the application via the UDP-Lite MIB module [RFC5097].3.4.3. Transport Features The transport features provided by UDP-Lite are: o unicast, multicast, anycast, or IPv4 broadcast transport (same as for UDP), o port multiplexing (same as for UDP), o message-oriented delivery (same as for UDP), o unidirectional or bidirectional communication where the transmissions in each direction are independent (same as for UDP), o non-reliable delivery (same as for UDP), o non-ordered delivery (same as for UDP), and o partial or full payload error detection (where the Checksum Coverage field indicates the size of the payload data covered by the checksum).3.5. Stream Control Transmission Protocol (SCTP) SCTP is a message-oriented IETF Standards Track transport protocol. The base protocol is specified in [RFC4960]. It supports multihoming and path failover to provide resilience to path failures. An SCTP association has multiple streams in each direction, providing in-sequence delivery of user messages within each stream. ThisFairhurst, et al. Informational [Page 14]
RFC 8095 Transport Services March 2017 allows it to minimize head-of-line blocking. SCTP supports multiple stream- scheduling schemes controlling stream multiplexing, including priority and fair weighting schemes. SCTP was originally developed for transporting telephony signaling messages and is deployed in telephony signaling networks, especially in mobile telephony networks. It can also be used for other services, for example, in the WebRTC framework for data channels.3.5.1. Protocol Description SCTP is a connection-oriented protocol using a four-way handshake to establish an SCTP association and a three-way message exchange to gracefully shut it down. It uses the same port number concept as DCCP, TCP, UDP, and UDP-Lite. SCTP only supports unicast. SCTP uses the 32-bit CRC32c for protecting SCTP packets against bit errors and misdelivery of packets to an unintended endpoint. This is stronger than the 16-bit checksums used by TCP or UDP. However, partial payload checksum coverage as provided by DCCP or UDP-Lite is not supported. SCTP has been designed with extensibility in mind. A common header is followed by a sequence of chunks. [RFC4960] defines how a receiver processes chunks with an unknown chunk type. The support of extensions can be negotiated during the SCTP handshake. Currently defined extensions include mechanisms for dynamic reconfiguration of streams [RFC6525] and IP addresses [RFC5061]. Furthermore, the extension specified in [RFC3758] introduces the concept of partial reliability for user messages. SCTP provides a message-oriented service. Multiple small user messages can be bundled into a single SCTP packet to improve efficiency. For example, this bundling may be done by delaying user messages at the sender, similar to Nagle's algorithm used by TCP. User messages that would result in IP packets larger than the MTU will be fragmented at the sender and reassembled at the receiver. There is no protocol limit on the user message size. For MTU discovery, the same mechanism as for TCP can be used [RFC1981] [RFC4821], as well as utilization of probe packets with padding chunks, as defined in [RFC4820]. [RFC4960] specifies TCP-friendly congestion control to protect the network against overload. SCTP also uses sliding window flow control to protect receivers against overflow. Similar to TCP, SCTP also supports delaying acknowledgments. [RFC7053] provides a way for the sender of user messages to request immediate sending of the corresponding acknowledgments.Fairhurst, et al. Informational [Page 15]
RFC 8095 Transport Services March 2017 Each SCTP association has between 1 and 65536 unidirectional streams in each direction. The number of streams can be different in each direction. Every user message is sent on a particular stream. User messages can be sent unordered or ordered upon request by the upper layer. Unordered messages can be delivered as soon as they are completely received. For user messages not requiring fragmentation, this minimizes head-of-line blocking. On the other hand, ordered messages sent on the same stream are delivered at the receiver in the same order as sent by the sender. The base protocol defined in [RFC4960] does not allow interleaving of user messages. Large messages on one stream can therefore block the sending of user messages on other streams. [SCTP-NDATA] describes a method to overcome this limitation. This document also specifies multiple algorithms for the sender-side selection of which streams to send data from, supporting a variety of scheduling algorithms including priority-based methods. The stream reconfiguration extension defined in [RFC6525] allows streams to be reset during the lifetime of an association and to increase the number of streams, if the number of streams negotiated in the SCTP handshake becomes insufficient. Each user message sent is delivered to the receiver or, in case of excessive retransmissions, the association is terminated in a non-graceful way [RFC4960], similar to TCP behavior. In addition to this reliable transfer, the partial reliability extension [RFC3758] allows a sender to abandon user messages. The application can specify the policy for abandoning user messages. SCTP supports multihoming. Each SCTP endpoint uses a list of IP addresses and a single port number. These addresses can be any mixture of IPv4 and IPv6 addresses. These addresses are negotiated during the handshake, and the address reconfiguration extension specified in [RFC5061] in combination with [RFC4895] can be used to change these addresses in an authenticated way during the lifetime of an SCTP association. This allows for transport-layer mobility. Multiple addresses are used for improved resilience. If a remote address becomes unreachable, the traffic is switched over to a reachable one, if one exists. For securing user messages, the use of TLS over SCTP has been specified in [RFC3436]. However, this solution does not support all services provided by SCTP, such as unordered delivery or partial reliability. Therefore, the use of DTLS over SCTP has been specified in [RFC6083] to overcome these limitations. When using DTLS over SCTP, the application can use almost all services provided by SCTP.Fairhurst, et al. Informational [Page 16]
RFC 8095 Transport Services March 2017 [NAT-SUPP] defines methods for endpoints and middleboxes to provide NAT traversal for SCTP over IPv4. For legacy NAT traversal, [RFC6951] defines the UDP encapsulation of SCTP packets. Alternatively, SCTP packets can be encapsulated in DTLS packets as specified in [SCTP-DTLS-ENCAPS]. The latter encapsulation is used within the WebRTC [WEBRTC-TRANS] context. An SCTP ABORT chunk may be used to force a SCTP endpoint to close a session [RFC4960], aborting the connection. SCTP has a well-defined API, described in the next subsection.3.5.2. Interface Description [RFC4960] defines an abstract API for the base protocol. This API describes the following functions callable by the upper layer of SCTP: Initialize, Associate, Send, Receive, Receive Unsent Message, Receive Unacknowledged Message, Shutdown, Abort, SetPrimary, Status, Change Heartbeat, Request Heartbeat, Get SRTT Report, Set Failure Threshold, Set Protocol Parameters, and Destroy. The following notifications are provided by the SCTP stack to the upper layer: COMMUNICATION UP, DATA ARRIVE, SHUTDOWN COMPLETE, COMMUNICATION LOST, COMMUNICATION ERROR, RESTART, SEND FAILURE, and NETWORK STATUS CHANGE. An extension to the BSD Sockets API is defined in [RFC6458] and covers: o the base protocol defined in [RFC4960]. The API allows control over local addresses and port numbers and the primary path. Furthermore, the application has fine control of parameters like retransmission thresholds, the path supervision, the delayed acknowledgment timeout, and the fragmentation point. The API provides a mechanism to allow the SCTP stack to notify the application about events if the application has requested them. These notifications provide information about status changes of the association and each of the peer addresses. In case of send failures, including drop of messages sent unreliably, the application can also be notified, and user messages can be returned to the application. When sending user messages, the application can indicate a stream id, a payload protocol identifier, and an indication of whether ordered delivery is requested. These parameters can also be provided on message reception. Additionally, a context can be provided when sending, which can be used in case of send failures. The sending of arbitrarily large user messages is supported.Fairhurst, et al. Informational [Page 17]
RFC 8095 Transport Services March 2017 o the SCTP Partial Reliability extension defined in [RFC3758] to specify for a user message the Partially Reliable SCTP (PR-SCTP) policy and the policy-specific parameter. Examples of these policies defined in [RFC3758] and [RFC7496] are: * limiting the time a user message is dealt with by the sender. * limiting the number of retransmissions for each fragment of a user message. If the number of retransmissions is limited to 0, one gets a service similar to UDP. * abandoning messages of lower priority in case of a send buffer shortage. o the SCTP Authentication extension defined in [RFC4895] allowing management of the shared keys and allowing the HMAC to use and set the chunk types (which are only accepted in an authenticated way) and get the list of chunks that are accepted by the local and remote endpoints in an authenticated way. o the SCTP Dynamic Address Reconfiguration extension defined in [RFC5061]. It allows the manual addition and deletion of local addresses for SCTP associations, as well as the enabling of automatic address addition and deletion. Furthermore, the peer can be given a hint for choosing its primary path. A BSD Sockets API extension has been defined in the documents that specify the following SCTP extensions: o the SCTP Stream Reconfiguration extension defined in [RFC6525]. The API allows triggering of the reset operation for incoming and outgoing streams and the whole association. It also provides a way to notify the association about the corresponding events. Furthermore, the application can increase the number of streams. o the UDP Encapsulation of SCTP packets extension defined in [RFC6951]. The API allows the management of the remote UDP encapsulation port. o the SCTP SACK-IMMEDIATELY extension defined in [RFC7053]. The API allows the sender of a user message to request the receiver to send the corresponding acknowledgment immediately. o the additional PR-SCTP policies defined in [RFC7496]. The API allows enabling/disabling the PR-SCTP extension, choosing the PR-SCTP policies defined in the document, and providing statistical information about abandoned messages.Fairhurst, et al. Informational [Page 18]
RFC 8095 Transport Services March 2017 Future documents describing SCTP extensions are expected to describe the corresponding BSD Sockets API extension in a "Socket API Considerations" section. The SCTP Socket API supports two kinds of sockets: o one-to-one style sockets (by using the socket type "SOCK_STREAM"). o one-to-many style socket (by using the socket type "SOCK_SEQPACKET"). One-to-one style sockets are similar to TCP sockets; there is a 1:1 relationship between the sockets and the SCTP associations (except for listening sockets). One-to-many style SCTP sockets are similar to unconnected UDP sockets, where there is a 1:n relationship between the sockets and the SCTP associations. The SCTP stack can provide information to the applications about state changes of the individual paths and the association whenever they occur. These events are delivered similarly to user messages but are specifically marked as notifications. New functions have been introduced to support the use of multiple local and remote addresses. Additional SCTP-specific send and receive calls have been defined to permit SCTP-specific information to be sent without using ancillary data in the form of additional Control Message (cmsg) calls. These functions provide support for detecting partial delivery of user messages and notifications. The SCTP Socket API allows a fine-grained control of the protocol behavior through an extensive set of socket options. The SCTP kernel implementations of FreeBSD, Linux, and Solaris follow mostly the specified extension to the BSD Sockets API for the base protocol and the corresponding supported protocol extensions.3.5.3. Transport Features The transport features provided by SCTP are: o connection-oriented transport with feature negotiation and application-to-port mapping, o unicast transport, o port multiplexing, o unidirectional or bidirectional communication,Fairhurst, et al. Informational [Page 19]
RFC 8095 Transport Services March 2017 o message-oriented delivery with durable message framing supporting multiple concurrent streams, o fully reliable, partially reliable, or unreliable delivery (based on user-specified policy to handle abandoned user messages) with drop notification, o ordered and unordered delivery within a stream, o support for stream scheduling prioritization, o segmentation, o user message bundling, o flow control using a window-based mechanism, o congestion control using methods similar to TCP, o strong error detection (CRC32c), and o transport-layer multihoming for resilience and mobility.3.6. Datagram Congestion Control Protocol (DCCP) The Datagram Congestion Control Protocol (DCCP) [RFC4340] is an IETF Standards Track bidirectional transport protocol that provides unicast connections of congestion-controlled messages without providing reliability. The DCCP Problem Statement [RFC4336] describes the goals that DCCP sought to address. It is suitable for applications that transfer fairly large amounts of data and that can benefit from control over the trade-off between timeliness and reliability [RFC4336]. DCCP offers low overhead, and many characteristics common to UDP, but can avoid "re-inventing the wheel" each time a new multimedia application emerges. Specifically, it includes core transport functions (feature negotiation, path state management, RTT calculation, PMTUD, etc.): DCCP applications select how they send packets and, where suitable, choose common algorithms to manage their functions. Examples of applications that can benefit from such transport services include interactive applications, streaming media, or on-line games [RFC4336].Fairhurst, et al. Informational [Page 20]
RFC 8095 Transport Services March 20173.6.1. Protocol Description DCCP is a connection-oriented datagram protocol that provides a three-way handshake to allow a client and server to set up a connection and provides mechanisms for orderly completion and immediate teardown of a connection. A DCCP protocol instance can be extended [RFC4340] and tuned using additional features. Some features are sender-side only, requiring no negotiation with the receiver; some are receiver-side only; and some are explicitly negotiated during connection setup. DCCP uses a Connect packet to initiate a session and permits each endpoint to choose the features it wishes to support. Simultaneous open [RFC5596], as in TCP, can enable interoperability in the presence of middleboxes. The Connect packet includes a Service Code [RFC5595] that identifies the application or protocol using DCCP, providing middleboxes with information about the intended use of a connection. The DCCP service is unicast-only. It provides multiplexing to multiple sockets at each endpoint using port numbers. An active DCCP session is identified by its four-tuple of local and remote IP addresses and local and remote port numbers. The protocol segments data into messages that are typically sized to fit in IP packets but may be fragmented if they are smaller than the maximum packet size. A DCCP interface allows applications to request fragmentation for packets larger than PMTU, but not larger than the maximum packet size allowed by the current congestion control mechanism (Congestion Control Maximum Packet Size (CCMPS)) [RFC4340]. Each message is identified by a sequence number. The sequence number is used to identify segments in acknowledgments, to detect unacknowledged segments, to measure RTT, etc. The protocol may support unordered delivery of data and does not itself provide retransmission. DCCP supports reduced checksum coverage, a partial payload protection mechanism similar to UDP-Lite. There is also a Data Checksum option, which when enabled, contains a strong Cyclic Redundancy Check (CRC), to enable endpoints to detect application data corruption. Receiver flow control is supported, which limits the amount of unacknowledged data that can be outstanding at a given time. A DCCP Reset packet may be used to force a DCCP endpoint to close a session [RFC4340], aborting the connection.Fairhurst, et al. Informational [Page 21]
RFC 8095 Transport Services March 2017 DCCP supports negotiation of the congestion control profile between endpoints, to provide plug-and-play congestion control mechanisms. Examples of specified profiles include "TCP-like" [RFC4341], "TCP- friendly" [RFC4342], and "TCP-friendly for small packets" [RFC5622]. Additional mechanisms are recorded in an IANA registry (see <http://www.iana.org/assignments/dccp-parameters>). A lightweight UDP-based encapsulation (DCCP-UDP) has been defined [RFC6773] that permits DCCP to be used over paths where DCCP is not natively supported. Support for DCCP in NAPT/NATs is defined in [RFC4340] and [RFC5595]. Upper-layer protocols specified on top of DCCP include DTLS [RFC5238], RTP [RFC5762], and Interactive Connectivity Establishment / Session Description Protocol (ICE/SDP) [RFC6773].3.6.2. Interface Description Functions expected for a DCCP API include: Open, Close, and Management of the progress a DCCP connection. The Open function provides feature negotiation, selection of an appropriate Congestion Control Identifier (CCID) for congestion control, and other parameters associated with the DCCP connection. A function allows an application to send DCCP datagrams, including setting the required checksum coverage and any required options. (DCCP permits sending datagrams with a zero-length payload.) A function allows reception of data, including indicating if the data was used or dropped. Functions can also make the status of a connection visible to an application, including detection of the maximum packet size and the ability to perform flow control by detecting a slow receiver at the sender. There is no API currently specified in the RFC Series.3.6.3. Transport Features The transport features provided by DCCP are: o unicast transport, o connection-oriented communication with feature negotiation and application-to-port mapping, o signaling of application class for middlebox support (implemented using Service Codes), o port multiplexing, o unidirectional or bidirectional communication,Fairhurst, et al. Informational [Page 22]
RFC 8095 Transport Services March 2017 o message-oriented delivery, o unreliable delivery with drop notification, o unordered delivery, o flow control (implemented using the slow receiver function), and o partial and full payload error detection (with optional strong integrity check).3.7. Transport Layer Security (TLS) and Datagram TLS (DTLS) as a Pseudotransport Transport Layer Security (TLS) [RFC5246] and Datagram TLS (DTLS) [RFC6347] are IETF protocols that provide several security-related features to applications. TLS is designed to run on top of a reliable streaming transport protocol (usually TCP), while DTLS is designed to run on top of a best-effort datagram protocol (UDP or DCCP [RFC5238]). At the time of writing, the current version of TLS is 1.2, defined in [RFC5246]; work on TLS version is 1.3 [TLS-1.3] nearing completion. DTLS provides nearly identical functionality to applications; it is defined in [RFC6347] and its current version is also 1.2. The TLS protocol evolved from the Secure Sockets Layer (SSL) [RFC6101] protocols developed in the mid-1990s to support protection of HTTP traffic. While older versions of TLS and DTLS are still in use, they provide weaker security guarantees. [RFC7457] outlines important attacks on TLS and DTLS. [RFC7525] is a Best Current Practices (BCP) document that describes secure configurations for TLS and DTLS to counter these attacks. The recommendations are applicable for the vast majority of use cases.3.7.1. Protocol Description Both TLS and DTLS provide the same security features and can thus be discussed together. The features they provide are: o Confidentiality o Data integrity o Peer authentication (optional) o Perfect forward secrecy (optional)Fairhurst, et al. Informational [Page 23]
RFC 8095 Transport Services March 2017 The authentication of the peer entity can be omitted; a common web use case is where the server is authenticated and the client is not. TLS also provides a completely anonymous operation mode in which neither peer's identity is authenticated. It is important to note that TLS itself does not specify how a peering entity's identity should be interpreted. For example, in the common use case of authentication by means of an X.509 certificate, it is the application's decision whether the certificate of the peering entity is acceptable for authorization decisions. Perfect forward secrecy, if enabled and supported by the selected algorithms, ensures that traffic encrypted and captured during a session at time t0 cannot be later decrypted at time t1 (t1 > t0), even if the long-term secrets of the communicating peers are later compromised. As DTLS is generally used over an unreliable datagram transport such as UDP, applications will need to tolerate lost, reordered, or duplicated datagrams. Like TLS, DTLS conveys application data in a sequence of independent records. However, because records are mapped to unreliable datagrams, there are several features unique to DTLS that are not applicable to TLS: o Record replay detection (optional). o Record size negotiation (estimates of PMTU and record size expansion factor). o Conveyance of IP don't fragment (DF) bit settings by application. o An anti-DoS stateless cookie mechanism (optional). Generally, DTLS follows the TLS design as closely as possible. To operate over datagrams, DTLS includes a sequence number and limited forms of retransmission and fragmentation for its internal operations. The sequence number may be used for detecting replayed information, according to the windowing procedure described inSection 4.1.2.6 of [RFC6347]. DTLS forbids the use of stream ciphers, which are essentially incompatible when operating on independent encrypted records.3.7.2. Interface Description TLS is commonly invoked using an API provided by packages such as OpenSSL, wolfSSL, or GnuTLS. Using such APIs entails the manipulation of several important abstractions, which fall into the following categories: long-term keys and algorithms, session state, and communications/connections.Fairhurst, et al. Informational [Page 24]
RFC 8095 Transport Services March 2017 Considerable care is required in the use of TLS APIs to ensure creation of a secure application. The programmer should have at least a basic understanding of encryption and digital signature algorithms and their strengths, public key infrastructure (including X.509 certificates and certificate revocation), and the Sockets API. See [RFC7525] and [RFC7457], as mentioned above. As an example, in the case of OpenSSL, the primary abstractions are the library itself, method (protocol), session, context, cipher, and connection. After initializing the library and setting the method, a cipher suite is chosen and used to configure a context object. Session objects may then be minted according to the parameters present in a context object and associated with individual connections. Depending on how precisely the programmer wishes to select different algorithmic or protocol options, various levels of details may be required.3.7.3. Transport Features Both TLS and DTLS employ a layered architecture. The lower layer is commonly called the "record protocol". It is responsible for: o message fragmentation, o authentication and integrity via message authentication codes (MACs), o data encryption, and o scheduling transmission using the underlying transport protocol. DTLS augments the TLS record protocol with: o ordering and replay protection, implemented using sequence numbers. Several protocols are layered on top of the record protocol. These include the handshake, alert, and change cipher spec protocols. There is also the data protocol, used to carry application traffic. The handshake protocol is used to establish cryptographic and compression parameters when a connection is first set up. In DTLS, this protocol also has a basic fragmentation and retransmission capability and a cookie-like mechanism to resist DoS attacks. (TLS compression is not recommended at present). The alert protocol is used to inform the peer of various conditions, most of which are terminal for the connection. The change cipher spec protocol is used to synchronize changes in cryptographic parameters for each peer.Fairhurst, et al. Informational [Page 25]
RFC 8095 Transport Services March 2017 The data protocol, when used with an appropriate cipher, provides: o authentication of one end or both ends of a connection, o confidentiality, and o cryptographic integrity protection. Both TLS and DTLS are unicast-only.3.8. Real-Time Transport Protocol (RTP) RTP provides an end-to-end network transport service, suitable for applications transmitting real-time data, such as audio, video or data, over multicast or unicast transport services, including TCP, UDP, UDP-Lite, DCCP, TLS, and DTLS.3.8.1. Protocol Description The RTP standard [RFC3550] defines a pair of protocols: RTP and the RTP Control Protocol (RTCP). The transport does not provide connection setup, instead relying on out-of-band techniques or associated control protocols to setup, negotiate parameters, or tear down a session. An RTP sender encapsulates audio/video data into RTP packets to transport media streams. The RFC Series specifies RTP payload formats that allow packets to carry a wide range of media and specifies a wide range of multiplexing, error control, and other support mechanisms. If a frame of media data is large, it will be fragmented into several RTP packets. Likewise, several small frames may be bundled into a single RTP packet. An RTP receiver collects RTP packets from the network, validates them for correctness, and sends them to the media decoder input queue. Missing packet detection is performed by the channel decoder. The playout buffer is ordered by time stamp and is used to reorder packets. Damaged frames may be repaired before the media payloads are decompressed to display or store the data. Some uses of RTP are able to exploit the partial payload protection features offered by DCCP and UDP-Lite. RTCP is a control protocol that works alongside an RTP flow. Both the RTP sender and receiver will send RTCP report packets. This is used to periodically send control information and report performance.Fairhurst, et al. Informational [Page 26]
RFC 8095 Transport Services March 2017 Based on received RTCP feedback, an RTP sender can adjust the transmission, e.g., perform rate adaptation at the application layer in the case of congestion. An RTCP receiver report (RTCP RR) is returned to the sender periodically to report key parameters (e.g., the fraction of packets lost in the last reporting interval, the cumulative number of packets lost, the highest sequence number received, and the inter-arrival jitter). The RTCP RR packets also contain timing information that allows the sender to estimate the network round-trip time (RTT) to the receivers. The interval between reports sent from each receiver tends to be on the order of a few seconds on average, although this varies with the session rate, and sub-second reporting intervals are possible for high rate sessions. The interval is randomized to avoid synchronization of reports from multiple receivers.3.8.2. Interface Description There is no standard API defined for RTP or RTCP. Implementations are typically tightly integrated with a particular application and closely follow the principles of application-level framing and integrated layer processing [ClarkArch] in media processing [RFC2736], error recovery and concealment, rate adaptation, and security [RFC7202]. Accordingly, RTP implementations tend to be targeted at particular application domains (e.g., voice-over-IP, IPTV, or video conferencing), with a feature set optimized for that domain, rather than being general purpose implementations of the protocol.3.8.3. Transport Features The transport features provided by RTP are: o unicast, multicast, or IPv4 broadcast (provided by lower-layer protocol), o port multiplexing (provided by lower-layer protocol), o unidirectional or bidirectional communication (provided by lower- layer protocol), o message-oriented delivery with support for media types and other extensions, o reliable delivery when using erasure coding or unreliable delivery with drop notification (if supported by lower-layer protocol),Fairhurst, et al. Informational [Page 27]
RFC 8095 Transport Services March 2017 o connection setup with feature negotiation (using associated protocols) and application-to-port mapping (provided by lower- layer protocol), o segmentation, and o performance metric reporting (using associated protocols).3.9. Hypertext Transport Protocol (HTTP) over TCP as a Pseudotransport The Hypertext Transfer Protocol (HTTP) is an application-level protocol widely used on the Internet. It provides object-oriented delivery of discrete data or files. Version 1.1 of the protocol is specified in [RFC7230] [RFC7231] [RFC7232] [RFC7233] [RFC7234] [RFC7235], and version 2 is specified in [RFC7540]. HTTP is usually transported over TCP using ports 80 and 443, although it can be used with other transports. When used over TCP, it inherits TCP's properties. Application-layer protocols may use HTTP as a substrate with an existing method and data formats, or specify new methods and data formats. There are various reasons for this practice listed in [RFC3205]; these include being a well-known and well-understood protocol, reusability of existing servers and client libraries, easy use of existing security mechanisms such as HTTP digest authentication [RFC7235] and TLS [RFC5246], and the ability of HTTP to traverse firewalls, which allows it to work over many types of infrastructure and in cases where an application server often needs to support HTTP anyway. Depending on application need, the use of HTTP as a substrate protocol may add complexity and overhead in comparison to a special- purpose protocol (e.g., HTTP headers, suitability of the HTTP security model, etc.). [RFC3205] addresses this issue, provides some guidelines, and identifies concerns about the use of HTTP standard ports 80 and 443, the use of the HTTP URL scheme, and interaction with existing firewalls, proxies, and NATs. Representational State Transfer (REST) [REST] is another example of how applications can use HTTP as a transport protocol. REST is an architecture style that may be used to build applications using HTTP as a communication protocol.3.9.1. Protocol Description The Hypertext Transfer Protocol (HTTP) is a request/response protocol. A client sends a request containing a request method, URI, and protocol version followed by message whose design is inspired byFairhurst, et al. Informational [Page 28]
RFC 8095 Transport Services March 2017 MIME (see [RFC7231] for the differences between an HTTP object and a MIME message), containing information about the client and request modifiers. The message can also contain a message body carrying application data. The server responds with a status or error code followed by a message containing information about the server and information about the data. This may include a message body. It is possible to specify a data format for the message body using MIME media types [RFC2045]. The protocol has additional features; some relevant to pseudotransport are described below. Content negotiation, specified in [RFC7231], is a mechanism provided by HTTP to allow selection of a representation for a requested resource. The client and server negotiate acceptable data formats, character sets, and data encoding (e.g., data can be transferred compressed using gzip). HTTP can accommodate exchange of messages as well as data streaming (using chunked transfer encoding [RFC7230]). It is also possible to request a part of a resource using an object range request [RFC7233]. The protocol provides powerful cache control signaling defined in [RFC7234]. The persistent connections of HTTP 1.1 and HTTP 2.0 allow multiple request/response transactions (streams) during the lifetime of a single HTTP connection. This reduces overhead during connection establishment and mitigates transport-layer slow-start that would have otherwise been incurred for each transaction. HTTP 2.0 connections can multiplex many request/response pairs in parallel on a single transport connection. Both are important to reduce latency for HTTP's primary use case. HTTP can be combined with security mechanisms, such as TLS (denoted by HTTPS). This adds protocol properties provided by such a mechanism (e.g., authentication and encryption). The TLS Application-Layer Protocol Negotiation (ALPN) extension [RFC7301] can be used to negotiate the HTTP version within the TLS handshake, eliminating the latency incurred by additional round-trip exchanges. Arbitrary cookie strings, included as part of the request headers, are often used as bearer tokens in HTTP.3.9.2. Interface Description There are many HTTP libraries available exposing different APIs. The APIs provide a way to specify a request by providing a URI, a method, request modifiers, and, optionally, a request body. For the response, callbacks can be registered that will be invoked when the response is received. If HTTPS is used, the API exposes a registration of callbacks when a server requests client authentication and when certificate verification is needed.Fairhurst, et al. Informational [Page 29]
RFC 8095 Transport Services March 2017 The World Wide Web Consortium (W3C) has standardized the XMLHttpRequest API [XHR]. This API can be used for sending HTTP/ HTTPS requests and receiving server responses. Besides the XML data format, the request and response data format can also be JSON, HTML, and plain text. JavaScript and XMLHttpRequest are ubiquitous programming models for websites and more general applications where native code is less attractive.3.9.3. Transport Features The transport features provided by HTTP, when used as a pseudotransport, are: o unicast transport (provided by the lower-layer protocol, usually TCP), o unidirectional or bidirectional communication, o transfer of objects in multiple streams with object content type negotiation, supporting partial transmission of object ranges, o ordered delivery (provided by the lower-layer protocol, usually TCP), o fully reliable delivery (provided by the lower-layer protocol, usually TCP), o flow control (provided by the lower-layer protocol, usually TCP), and o congestion control (provided by the lower-layer protocol, usually TCP). HTTPS (HTTP over TLS) additionally provides the following features (as provided by TLS): o authentication (of one or both ends of a connection), o confidentiality, and o integrity protection.Fairhurst, et al. Informational [Page 30]
RFC 8095 Transport Services March 20173.10. File Delivery over Unidirectional Transport / Asynchronous Layered Coding (FLUTE/ALC) for Reliable Multicast FLUTE/ALC is an IETF Standards Track protocol specified in [RFC6726] and [RFC5775]. It provides object-oriented delivery of discrete data or files. Asynchronous Layer Coding (ALC) provides an underlying reliable transport service and FLUTE a file-oriented specialization of the ALC service (e.g., to carry associated metadata). [RFC6726] and [RFC5775] are non-backward-compatible updates of [RFC3926] and [RFC3450], which are Experimental protocols; these Experimental protocols are currently largely deployed in the 3GPP Multimedia Broadcast / Multicast Service (MBMS) (see [MBMS], Section 7) and similar contexts (e.g., the Japanese ISDB-Tmm standard). The FLUTE/ALC protocol has been designed to support massively scalable reliable bulk data dissemination to receiver groups of arbitrary size using IP Multicast over any type of delivery network, including unidirectional networks (e.g., broadcast wireless channels). However, the FLUTE/ALC protocol also supports point-to- point unicast transmissions. FLUTE/ALC bulk data dissemination has been designed for discrete file or memory-based "objects". Although FLUTE/ALC is not well adapted to byte and message streaming, there is an exception: FLUTE/ALC is used to carry 3GPP Dynamic Adaptive Streaming over HTTP (DASH) when scalability is a requirement (see [MBMS], Section 5.6). FLUTE/ALC's reliability, delivery mode, congestion control, and flow/ rate control mechanisms can be separately controlled to meet different application needs.Section 4.1 of [RFC8085] describes multicast congestion control requirements for UDP.3.10.1. Protocol Description The FLUTE/ALC protocol works on top of UDP (though it could work on top of any datagram delivery transport protocol), without requiring any connectivity from receivers to the sender. Purely unidirectional networks are therefore supported by FLUTE/ALC. This guarantees scalability to an unlimited number of receivers in a session, since the sender behaves exactly the same regardless of the number of receivers. FLUTE/ALC supports the transfer of bulk objects such as file or in-memory content, using either a push or an on-demand mode. In push mode, content is sent once to the receivers, while in on-demand mode, content is sent continuously during periods of time that can greatly exceed the average time required to download the session objects (see[RFC5651], Section 4.2).Fairhurst, et al. Informational [Page 31]
RFC 8095 Transport Services March 2017 This enables receivers to join a session asynchronously, at their own discretion, receive the content, and leave the session. In this case, data content is typically sent continuously, in loops (also known as "carousels"). FLUTE/ALC also supports the transfer of an object stream, with loose real-time constraints. This is particularly useful to carry 3GPP DASH when scalability is a requirement and unicast transmissions over HTTP cannot be used ([MBMS], Section 5.6). In this case, packets are sent in sequence using push mode. FLUTE/ALC is not well adapted to byte and message streaming, and other solutions could be preferred (e.g., FECFRAME [RFC6363] with real-time flows). The FLUTE file delivery instantiation of ALC provides a metadata delivery service. Each object of the FLUTE/ALC session is described in a dedicated entry of a File Delivery Table (FDT), using an XML format (see[RFC6726], Section 3.2). This metadata can include, but is not restricted to, a URI attribute (to identify and locate the object), a media type attribute, a size attribute, an encoding attribute, or a message digest attribute. Since the set of objects sent within a session can be dynamic, with new objects being added and old ones removed, several instances of the FDT can be sent, and a mechanism is provided to identify a new FDT instance. Error detection and verification of the protocol control information relies on the underlying transport (e.g., UDP checksum). To provide robustness against packet loss and improve the efficiency of the on-demand mode, FLUTE/ALC relies on packet erasure coding (Application-Layer Forward Error Correction (AL-FEC)). AL-FEC encoding is proactive (since there is no feedback and therefore no (N)ACK-based retransmission), and ALC packets containing repair data are sent along with ALC packets containing source data. Several FEC Schemes have been standardized; FLUTE/ALC does not mandate the use of any particular one. Several strategies concerning the transmission order of ALC source and repair packets are possible, in particular, in on-demand mode where it can deeply impact the service provided (e.g., to favor the recovery of objects in sequence or, at the other extreme, to favor the recovery of all objects in parallel), and FLUTE/ALC does not mandate nor recommend the use of any particular one. A FLUTE/ALC session is composed of one or more channels, associated to different destination unicast and/or multicast IP addresses. ALC packets are sent in those channels at a certain transmission rate, with a rate that often differs depending on the channel. FLUTE/ALC does not mandate nor recommend any strategy to select which ALC packet to send on which channel. FLUTE/ALC can use a multiple rate congestion control building block (e.g., Wave and Equation Based RateFairhurst, et al. Informational [Page 32]
RFC 8095 Transport Services March 2017 Control (WEBRC)) to provide congestion control that is feedback free, where receivers adjust their reception rates individually by joining and leaving channels associated with the session. To that purpose, the ALC header provides a specific field to carry congestion-control- specific information. However, FLUTE/ALC does not mandate the use of a particular congestion control mechanism although WEBRC is mandatory to support for the Internet ([RFC6726], Section 1.1.4). FLUTE/ALC is often used over a network path with pre-provisioned capacity [RFC8085] where there are no flows competing for capacity. In this case, a sender-based rate control mechanism and a single channel are sufficient. [RFC6584] provides per-packet authentication, integrity, and anti- replay protection in the context of the ALC and NORM protocols. Several mechanisms are proposed that seamlessly integrate into these protocols using the ALC and NORM header extension mechanisms.3.10.2. Interface Description The FLUTE/ALC specification does not describe a specific API to control protocol operation. Although open source and commercial implementations have specified APIs, there is no IETF-specified API for FLUTE/ALC.3.10.3. Transport Features The transport features provided by FLUTE/ALC are: o unicast, multicast, anycast, or IPv4 broadcast transmission, o object-oriented delivery of discrete data or files and associated metadata, o fully reliable or partially reliable delivery (of file or in- memory objects), using proactive packet erasure coding (AL-FEC) to recover from packet erasures, o ordered or unordered delivery (of file or in-memory objects), o error detection (based on the UDP checksum), o per-packet authentication, o per-packet integrity, o per-packet replay protection, and o congestion control for layered flows (e.g., with WEBRC).Fairhurst, et al. Informational [Page 33]
RFC 8095 Transport Services March 20173.11. NACK-Oriented Reliable Multicast (NORM) NORM is an IETF Standards Track protocol specified in [RFC5740]. It provides object-oriented delivery of discrete data or files. The protocol was designed to support reliable bulk data dissemination to receiver groups using IP Multicast but also provides for point-to- point unicast operation. Support for bulk data dissemination includes discrete file or computer memory-based "objects" as well as byte and message streaming. NORM can incorporate packet erasure coding as a part of its selective Automatic Repeat reQuest (ARQ) in response to negative acknowledgments from the receiver. The packet erasure coding can also be proactively applied for forward protection from packet loss. NORM transmissions are governed by TCP-Friendly Multicast Congestion Control (TFMCC) [RFC4654]. The reliability, congestion control, and flow control mechanisms can be separately controlled to meet different application needs.3.11.1. Protocol Description The NORM protocol is encapsulated in UDP datagrams and thus provides multiplexing for multiple sockets on hosts using port numbers. For loosely coordinated IP Multicast, NORM is not strictly connection- oriented although per-sender state is maintained by receivers for protocol operation. [RFC5740] does not specify a handshake protocol for connection establishment. Separate session initiation can be used to coordinate port numbers. However, in-band "client-server" style connection establishment can be accomplished with the NORM congestion control signaling messages using port binding techniques like those for TCP client-server connections. NORM supports bulk "objects" such as file or in-memory content but also can treat a stream of data as a logical bulk object for purposes of packet erasure coding. In the case of stream transport, NORM can support either byte streams or message streams where application- defined message boundary information is carried in the NORM protocol messages. This allows the receiver(s) to join/rejoin and recover message boundaries mid-stream as needed. Application content is carried and identified by the NORM protocol with encoding symbol identifiers depending upon the Forward Error Correction (FEC) Scheme [RFC5052] configured. NORM uses NACK-based selective ARQ to reliably deliver the application content to the receiver(s). NORM proactively measures round-trip timing information to scale ARQ timers appropriately and to support congestion control. For multicastFairhurst, et al. Informational [Page 34]
RFC 8095 Transport Services March 2017 operation, timer-based feedback suppression is used to achieve group size scaling with low feedback traffic levels. The feedback suppression is not applied for unicast operation. NORM uses rate-based congestion control based upon the TCP-Friendly Rate Control (TFRC) [RFC5348] principles that are also used in DCCP [RFC4340]. NORM uses control messages to measure RTT and collect congestion event information (e.g., reflecting a loss event or ECN event) from the receiver(s) to support dynamic adjustment or the rate. TCP-Friendly Multicast Congestion Control (TFMCC) [RFC4654] provides extra features to support multicast but is functionally equivalent to TFRC for unicast. Error detection and verification of the protocol control information relies on the on the underlying transport (e.g., UDP checksum). The reliability mechanism is decoupled from congestion control. This allows invocation of alternative arrangements of transport services, for example, to support, fixed-rate reliable delivery or unreliable delivery (that may optionally be "better than best effort" via packet erasure coding) using TFRC. Alternative congestion control techniques may be applied, for example, TFRC with congestion event detection based on ECN. While NORM provides NACK-based reliability, it also supports a positive acknowledgment (ACK) mechanism that can be used for receiver flow control. This mechanism is decoupled from the reliability and congestion control, supporting applications with different needs. One example is use of NORM for quasi-reliable delivery, where timely delivery of newer content may be favored over completely reliable delivery of older content within buffering and RTT constraints.3.11.2. Interface Description The NORM specification does not describe a specific API to control protocol operation. A freely available, open-source reference implementation of NORM is available at <https://www.nrl.navy.mil/itd/ncs/products/norm>, and a documented API is provided for this implementation. While a sockets-like API is not currently documented, the existing API supports the necessary functions for that to be implemented.Fairhurst, et al. Informational [Page 35]
RFC 8095 Transport Services March 20173.11.3. Transport Features The transport features provided by NORM are: o unicast or multicast transport, o unidirectional communication, o stream-oriented delivery in a single stream or object-oriented delivery of in-memory data or file bulk content objects, o fully reliable (NACK-based) or partially reliable (using erasure coding both proactively and as part of ARQ) delivery, o unordered delivery, o error detection (relies on UDP checksum), o segmentation, o data bundling (using Nagle's algorithm), o flow control (timer-based and/or ACK-based), and o congestion control (also supporting fixed-rate reliable or unreliable delivery).3.12. Internet Control Message Protocol (ICMP) The Internet Control Message Protocol (ICMP) [RFC792] for IPv4 and ICMP for IPv6 [RFC4443] are IETF Standards Track protocols. It is a connectionless unidirectional protocol that delivers individual messages, without error correction, congestion control, or flow control. Messages may be sent as unicast, IPv4 broadcast, or multicast datagrams (IPv4 and IPv6), in addition to anycast datagrams. While ICMP is not typically described as a transport protocol, it does position itself over the network layer, and the operation of other transport protocols can be closely linked to the functions provided by ICMP. Transport protocols and upper-layer protocols can use received ICMP messages to help them make appropriate decisions when network or endpoint errors are reported, for example, to implement ICMP-based Path MTU Discovery (PMTUD) [RFC1191] [RFC1981] or assist in Packetization Layer PMTUD (PLPMTUD) [RFC4821]. Such reactions to received messages need to protect from off-path data injectionFairhurst, et al. Informational [Page 36]
RFC 8095 Transport Services March 2017 [RFC8085] to avoid an application receiving packets created by an unauthorized third party. An application therefore needs to ensure that all messages are appropriately validated by checking the payload of the messages to ensure they are received in response to actually transmitted traffic (e.g., a reported error condition that corresponds to a UDP datagram or TCP segment was actually sent by the application). This requires context [RFC6056], such as local state about communication instances to each destination (e.g., in TCP, DCCP, or SCTP). This state is not always maintained by UDP-based applications [RFC8085].3.12.1. Protocol Description ICMP is a connectionless unidirectional protocol. It delivers independent messages, called "datagrams". Each message is required to carry a checksum as an integrity check and to protect from misdelivery to an unintended endpoint. ICMP messages typically relay diagnostic information from an endpoint [RFC1122] or network device [RFC1812] addressed to the sender of a flow. This usually contains the network protocol header of a packet that encountered a reported issue. Some formats of messages can also carry other payload data. Each message carries an integrity check calculated in the same way as for UDP; this checksum is not optional. The RFC Series defines additional IPv6 message formats to support a range of uses. In the case of IPv6, the protocol incorporates neighbor discovery [RFC4861] [RFC3971] (provided by ARP for IPv4) and Multicast Listener Discovery (MLD) [RFC2710] group management functions (provided by IGMP for IPv4). Reliable transmission cannot be assumed. A receiving application that is unable to run sufficiently fast, or frequently, may miss messages since there is no flow or congestion control. In addition, some network devices rate-limit ICMP messages.3.12.2. Interface Description ICMP processing is integrated in many connection-oriented transports but, like other functions, needs to be provided by an upper-layer protocol when using UDP and UDP-Lite. On some stacks, a bound socket also allows a UDP application to be notified when ICMP error messages are received for its transmissions [RFC8085].Fairhurst, et al. Informational [Page 37]
RFC 8095 Transport Services March 2017 Any response to ICMP error messages ought to be robust to temporary routing failures (sometimes called "soft errors"), e.g., transient ICMP "unreachable" messages ought to not normally cause a communication abort [RFC5461] [RFC8085].3.12.3. Transport Features ICMP does not provide any transport service directly to applications. Used together with other transport protocols, it provides transmission of control, error, and measurement data between endpoints or from devices along the path to one endpoint.4. Congestion Control Congestion control is critical to the stable operation of the Internet. A variety of mechanisms are used to provide the congestion control needed by many Internet transport protocols. Congestion is detected based on sensing of network conditions, whether through explicit or implicit feedback. The congestion control mechanisms that can be applied by different transport protocols are largely orthogonal to the choice of transport protocol. This section provides an overview of the congestion control mechanisms available to the protocols described inSection 3. Many protocols use a separate window to determine the maximum sending rate that is allowed by the congestion control. The used congestion control mechanism will increase the congestion window if feedback is received that indicates that the currently used network path is not congested and will reduce the window otherwise. Window-based mechanisms often increase their window slowing over multiple RTTs, while decreasing strongly when the first indication of congestion is received. One example is an Additive Increase Multiplicative Decrease (AIMD) scheme, where the window is increased by a certain number of packets/bytes for each data segment that has been successfully transmitted, while the window decreases multiplicatively on the occurrence of a congestion event. This can lead to a rather unstable, oscillating sending rate but will resolve a congestion situation quickly. Examples of window-based AIMD schemes include TCP NewReno [RFC5681], TCP Cubic [CUBIC] (the default mechanism for TCP in Linux), and CCID 2 specified for DCCP [RFC4341]. Some classes of applications prefer to use a transport service that allows sending at a more stable rate that is slowly varied in response to congestion. Rate-based methods offer this type of congestion control and have been defined based on the loss ratio and observed round-trip time, such as TFRC [RFC5348] and TFRC-SPFairhurst, et al. Informational [Page 38]
RFC 8095 Transport Services March 2017 [RFC4828]. These methods utilize a throughput equation to determine the maximum acceptable rate. Such methods are used with DCCP CCID 3 [RFC4342], CCID 4 [RFC5622], WEBRC [RFC3738], and other applications. Another class of applications prefers a transport service that yields to other (higher-priority) traffic, such as interactive transmissions. While most traffic in the Internet uses loss-based congestion control and therefore tends to fill the network buffers (to a certain level if Active Queue Management (AQM) is used), low- priority congestion control methods often react to changes in delay as an earlier indication of congestion. This approach tends to induce less loss than a loss-based method but does generally not compete well with loss-based traffic across shared bottleneck links. Therefore, methods such as LEDBAT [RFC6817] are deployed in the Internet for scavenger traffic that aims to only utilize otherwise unused capacity.5. Transport Features The transport protocol features described in this document can be used as a basis for defining common transport features. These are listed below with the protocols supporting them: o Control Functions * Addressing + unicast (TCP, MPTCP, UDP, UDP-Lite, SCTP, DCCP, TLS, RTP, HTTP, ICMP) + multicast (UDP, UDP-Lite, RTP, ICMP, FLUTE/ALC, NORM). Note that, as TLS and DTLS are unicast-only, there is no widely deployed mechanism for supporting the features listed under the Security bullet (below) when using multicast addressing. + IPv4 broadcast (UDP, UDP-Lite, ICMP) + anycast (UDP, UDP-Lite). Connection-oriented protocols such as TCP and DCCP have also been deployed using anycast addressing, with the risk that routing changes may cause connection failure. * Association type + connection-oriented (TCP, MPTCP, DCCP, SCTP, TLS, RTP, HTTP, NORM) + connectionless (UDP, UDP-Lite, FLUTE/ALC)Fairhurst, et al. Informational [Page 39]
RFC 8095 Transport Services March 2017 * Multihoming support + resilience and mobility (MPTCP, SCTP) + load balancing (MPTCP) + address family multiplexing (MPTCP, SCTP) * Middlebox cooperation + application-class signaling to middleboxes (DCCP) + error condition signaling from middleboxes and routers to endpoints (ICMP) * Signaling + control information and error signaling (ICMP) + application performance reporting (RTP) o Delivery * Reliability + fully reliable delivery (TCP, MPTCP, SCTP, TLS, HTTP, FLUTE/ ALC, NORM) + partially reliable delivery (SCTP, NORM) - using packet erasure coding (RTP, FLUTE/ALC, NORM) - with specified policy for dropped messages (SCTP) + unreliable delivery (SCTP, UDP, UDP-Lite, DCCP, RTP) - with drop notification to sender (SCTP, DCCP, RTP) + error detection - checksum for error detection (TCP, MPTCP, UDP, UDP-Lite, SCTP, DCCP, TLS, DTLS, FLUTE/ALC, NORM, ICMP) - partial payload checksum protection (UDP-Lite, DCCP). Some uses of RTP can exploit partial payload checksum protection feature to provide a corruption-tolerant transport service.Fairhurst, et al. Informational [Page 40]
RFC 8095 Transport Services March 2017 - checksum optional (UDP). Possible with IPv4 and, in certain cases, with IPv6. * Ordering + ordered delivery (TCP, MPTCP, SCTP, TLS, RTP, HTTP, FLUTE) + unordered delivery permitted (UDP, UDP-Lite, SCTP, DCCP, RTP, NORM) * Type/framing + stream-oriented delivery (TCP, MPTCP, SCTP, TLS, HTTP) - with multiple streams per association (SCTP, HTTP2) + message-oriented delivery (UDP, UDP-Lite, SCTP, DCCP, DTLS, RTP) + object-oriented delivery of discrete data or files and associated metadata (HTTP, FLUTE/ALC, NORM) - with partial delivery of object ranges (HTTP) * Directionality + unidirectional (UDP, UDP-Lite, DCCP, RTP, FLUTE/ALC, NORM) + bidirectional (TCP, MPTCP, SCTP, TLS, HTTP) o Transmission control * flow control (TCP, MPTCP, SCTP, DCCP, TLS, RTP, HTTP) * congestion control (TCP, MPTCP, SCTP, DCCP, RTP, FLUTE/ALC, NORM). Congestion control can also provided by the transport supporting an upper-layer transport (e.g., TLS, RTP, HTTP). * segmentation (TCP, MPTCP, SCTP, TLS, RTP, HTTP, FLUTE/ALC, NORM) * data/message bundling (TCP, MPTCP, SCTP, TLS, HTTP) * stream scheduling prioritization (SCTP, HTTP2) * endpoint multiplexing (MPTCP)Fairhurst, et al. Informational [Page 41]
RFC 8095 Transport Services March 2017 o Security * authentication of one end of a connection (TLS, DTLS, FLUTE/ ALC) * authentication of both ends of a connection (TLS, DTLS) * confidentiality (TLS, DTLS) * cryptographic integrity protection (TLS, DTLS) * replay protection (TLS, DTLS, FLUTE/ALC)6. IANA Considerations This document does not require any IANA actions.7. Security Considerations This document surveys existing transport protocols and protocols providing transport-like services. Confidentiality, integrity, and authenticity are among the features provided by those services. This document does not specify any new features or mechanisms for providing these features. Each RFC referenced by this document discusses the security considerations of the specification it contains.8. Informative References [ClarkArch] Clark, D. and D. Tennenhouse, "Architectural Considerations for a New Generation of Protocols", Proceedings of ACM SIGCOMM, DOI 10.1145/99517.99553, 1990. [CUBIC] Rhee, I., Xu, L., Ha, S., Zimmermann, A., Eggert, L., and R. Scheffenegger, "CUBIC for Fast Long-Distance Networks", Work in Progress,draft-ietf-tcpm-cubic-04, February 2017. [MBMS] 3GPP, "Multimedia Broadcast/Multicast Service (MBMS); Protocols and codecs", 3GPP TS 26.346, 2015, <http://www.3gpp.org/DynaReport/26346.htm>. [NAT-SUPP] Stewart, R., Tuexen, M., and I. Ruengeler, "Stream Control Transmission Protocol (SCTP) Network Address Translation Support", Work in Progress,draft-ietf-tsvwg-natsupp-09, May 2016.Fairhurst, et al. Informational [Page 42]
RFC 8095 Transport Services March 2017 [POSIX] IEEE, "Standard for Information Technology -- Portable Operating System Interface (POSIX(R)) Base Specifications, Issue 7", IEEE 1003.1, DOI 10.1109/ieeestd.2016.7582338, <http://ieeexplore.ieee.org/document/7582338/>. [REST] Fielding, R., "Architectural Styles and the Design of Network-based Software Architectures, Chapter 5: Representational State Transfer", Ph.D. Dissertation, University of California, Irvine, 2000. [RFC768] Postel, J., "User Datagram Protocol", STD 6,RFC 768, DOI 10.17487/RFC0768, August 1980, <http://www.rfc-editor.org/info/rfc768>. [RFC792] Postel, J., "Internet Control Message Protocol", STD 5,RFC 792, DOI 10.17487/RFC0792, September 1981, <http://www.rfc-editor.org/info/rfc792>. [RFC793] Postel, J., "Transmission Control Protocol", STD 7,RFC 793, DOI 10.17487/RFC0793, September 1981, <http://www.rfc-editor.org/info/rfc793>. [RFC1071] Braden, R., Borman, D., and C. Partridge, "Computing the Internet checksum",RFC 1071, DOI 10.17487/RFC1071, September 1988, <http://www.rfc-editor.org/info/rfc1071>. [RFC1122] Braden, R., Ed., "Requirements for Internet Hosts - Communication Layers", STD 3,RFC 1122, DOI 10.17487/RFC1122, October 1989, <http://www.rfc-editor.org/info/rfc1122>. [RFC1191] Mogul, J. and S. Deering, "Path MTU discovery",RFC 1191, DOI 10.17487/RFC1191, November 1990, <http://www.rfc-editor.org/info/rfc1191>. [RFC1812] Baker, F., Ed., "Requirements for IP Version 4 Routers",RFC 1812, DOI 10.17487/RFC1812, June 1995, <http://www.rfc-editor.org/info/rfc1812>. [RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery for IP version 6",RFC 1981, DOI 10.17487/RFC1981, August 1996, <http://www.rfc-editor.org/info/rfc1981>. [RFC2018] Mathis, M., Mahdavi, J., Floyd, S., and A. Romanow, "TCP Selective Acknowledgment Options",RFC 2018, DOI 10.17487/RFC2018, October 1996, <http://www.rfc-editor.org/info/rfc2018>.Fairhurst, et al. Informational [Page 43]
RFC 8095 Transport Services March 2017 [RFC2045] Freed, N. and N. Borenstein, "Multipurpose Internet Mail Extensions (MIME) Part One: Format of Internet Message Bodies",RFC 2045, DOI 10.17487/RFC2045, November 1996, <http://www.rfc-editor.org/info/rfc2045>. [RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification",RFC 2460, DOI 10.17487/RFC2460, December 1998, <http://www.rfc-editor.org/info/rfc2460>. [RFC2710] Deering, S., Fenner, W., and B. Haberman, "Multicast Listener Discovery (MLD) for IPv6",RFC 2710, DOI 10.17487/RFC2710, October 1999, <http://www.rfc-editor.org/info/rfc2710>. [RFC2736] Handley, M. and C. Perkins, "Guidelines for Writers of RTP Payload Format Specifications",BCP 36,RFC 2736, DOI 10.17487/RFC2736, December 1999, <http://www.rfc-editor.org/info/rfc2736>. [RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The Addition of Explicit Congestion Notification (ECN) to IP",RFC 3168, DOI 10.17487/RFC3168, September 2001, <http://www.rfc-editor.org/info/rfc3168>. [RFC3205] Moore, K., "On the use of HTTP as a Substrate",BCP 56,RFC 3205, DOI 10.17487/RFC3205, February 2002, <http://www.rfc-editor.org/info/rfc3205>. [RFC3260] Grossman, D., "New Terminology and Clarifications for Diffserv",RFC 3260, DOI 10.17487/RFC3260, April 2002, <http://www.rfc-editor.org/info/rfc3260>. [RFC3436] Jungmaier, A., Rescorla, E., and M. Tuexen, "Transport Layer Security over Stream Control Transmission Protocol",RFC 3436, DOI 10.17487/RFC3436, December 2002, <http://www.rfc-editor.org/info/rfc3436>. [RFC3450] Luby, M., Gemmell, J., Vicisano, L., Rizzo, L., and J. Crowcroft, "Asynchronous Layered Coding (ALC) Protocol Instantiation",RFC 3450, DOI 10.17487/RFC3450, December 2002, <http://www.rfc-editor.org/info/rfc3450>. [RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, "RTP: A Transport Protocol for Real-Time Applications", STD 64,RFC 3550, DOI 10.17487/RFC3550, July 2003, <http://www.rfc-editor.org/info/rfc3550>.Fairhurst, et al. Informational [Page 44]
RFC 8095 Transport Services March 2017 [RFC3738] Luby, M. and V. Goyal, "Wave and Equation Based Rate Control (WEBRC) Building Block",RFC 3738, DOI 10.17487/RFC3738, April 2004, <http://www.rfc-editor.org/info/rfc3738>. [RFC3758] Stewart, R., Ramalho, M., Xie, Q., Tuexen, M., and P. Conrad, "Stream Control Transmission Protocol (SCTP) Partial Reliability Extension",RFC 3758, DOI 10.17487/RFC3758, May 2004, <http://www.rfc-editor.org/info/rfc3758>. [RFC3828] Larzon, L-A., Degermark, M., Pink, S., Jonsson, L-E., Ed., and G. Fairhurst, Ed., "The Lightweight User Datagram Protocol (UDP-Lite)",RFC 3828, DOI 10.17487/RFC3828, July 2004, <http://www.rfc-editor.org/info/rfc3828>. [RFC3926] Paila, T., Luby, M., Lehtonen, R., Roca, V., and R. Walsh, "FLUTE - File Delivery over Unidirectional Transport",RFC 3926, DOI 10.17487/RFC3926, October 2004, <http://www.rfc-editor.org/info/rfc3926>. [RFC3971] Arkko, J., Ed., Kempf, J., Zill, B., and P. Nikander, "SEcure Neighbor Discovery (SEND)",RFC 3971, DOI 10.17487/RFC3971, March 2005, <http://www.rfc-editor.org/info/rfc3971>. [RFC4336] Floyd, S., Handley, M., and E. Kohler, "Problem Statement for the Datagram Congestion Control Protocol (DCCP)",RFC 4336, DOI 10.17487/RFC4336, March 2006, <http://www.rfc-editor.org/info/rfc4336>. [RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram Congestion Control Protocol (DCCP)",RFC 4340, DOI 10.17487/RFC4340, March 2006, <http://www.rfc-editor.org/info/rfc4340>. [RFC4341] Floyd, S. and E. Kohler, "Profile for Datagram Congestion Control Protocol (DCCP) Congestion Control ID 2: TCP-like Congestion Control",RFC 4341, DOI 10.17487/RFC4341, March 2006, <http://www.rfc-editor.org/info/rfc4341>. [RFC4342] Floyd, S., Kohler, E., and J. Padhye, "Profile for Datagram Congestion Control Protocol (DCCP) Congestion Control ID 3: TCP-Friendly Rate Control (TFRC)",RFC 4342, DOI 10.17487/RFC4342, March 2006, <http://www.rfc-editor.org/info/rfc4342>.Fairhurst, et al. Informational [Page 45]
RFC 8095 Transport Services March 2017 [RFC4443] Conta, A., Deering, S., and M. Gupta, Ed., "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification",RFC 4443, DOI 10.17487/RFC4443, March 2006, <http://www.rfc-editor.org/info/rfc4443>. [RFC4654] Widmer, J. and M. Handley, "TCP-Friendly Multicast Congestion Control (TFMCC): Protocol Specification",RFC 4654, DOI 10.17487/RFC4654, August 2006, <http://www.rfc-editor.org/info/rfc4654>. [RFC4820] Tuexen, M., Stewart, R., and P. Lei, "Padding Chunk and Parameter for the Stream Control Transmission Protocol (SCTP)",RFC 4820, DOI 10.17487/RFC4820, March 2007, <http://www.rfc-editor.org/info/rfc4820>. [RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU Discovery",RFC 4821, DOI 10.17487/RFC4821, March 2007, <http://www.rfc-editor.org/info/rfc4821>. [RFC4828] Floyd, S. and E. Kohler, "TCP Friendly Rate Control (TFRC): The Small-Packet (SP) Variant",RFC 4828, DOI 10.17487/RFC4828, April 2007, <http://www.rfc-editor.org/info/rfc4828>. [RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman, "Neighbor Discovery for IP version 6 (IPv6)",RFC 4861, DOI 10.17487/RFC4861, September 2007, <http://www.rfc-editor.org/info/rfc4861>. [RFC4895] Tuexen, M., Stewart, R., Lei, P., and E. Rescorla, "Authenticated Chunks for the Stream Control Transmission Protocol (SCTP)",RFC 4895, DOI 10.17487/RFC4895, August 2007, <http://www.rfc-editor.org/info/rfc4895>. [RFC4960] Stewart, R., Ed., "Stream Control Transmission Protocol",RFC 4960, DOI 10.17487/RFC4960, September 2007, <http://www.rfc-editor.org/info/rfc4960>. [RFC5052] Watson, M., Luby, M., and L. Vicisano, "Forward Error Correction (FEC) Building Block",RFC 5052, DOI 10.17487/RFC5052, August 2007, <http://www.rfc-editor.org/info/rfc5052>.Fairhurst, et al. Informational [Page 46]
RFC 8095 Transport Services March 2017 [RFC5061] Stewart, R., Xie, Q., Tuexen, M., Maruyama, S., and M. Kozuka, "Stream Control Transmission Protocol (SCTP) Dynamic Address Reconfiguration",RFC 5061, DOI 10.17487/RFC5061, September 2007, <http://www.rfc-editor.org/info/rfc5061>. [RFC5097] Renker, G. and G. Fairhurst, "MIB for the UDP-Lite protocol",RFC 5097, DOI 10.17487/RFC5097, January 2008, <http://www.rfc-editor.org/info/rfc5097>. [RFC5238] Phelan, T., "Datagram Transport Layer Security (DTLS) over the Datagram Congestion Control Protocol (DCCP)",RFC 5238, DOI 10.17487/RFC5238, May 2008, <http://www.rfc-editor.org/info/rfc5238>. [RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.2",RFC 5246, DOI 10.17487/RFC5246, August 2008, <http://www.rfc-editor.org/info/rfc5246>. [RFC5348] Floyd, S., Handley, M., Padhye, J., and J. Widmer, "TCP Friendly Rate Control (TFRC): Protocol Specification",RFC 5348, DOI 10.17487/RFC5348, September 2008, <http://www.rfc-editor.org/info/rfc5348>. [RFC5461] Gont, F., "TCP's Reaction to Soft Errors",RFC 5461, DOI 10.17487/RFC5461, February 2009, <http://www.rfc-editor.org/info/rfc5461>. [RFC5595] Fairhurst, G., "The Datagram Congestion Control Protocol (DCCP) Service Codes",RFC 5595, DOI 10.17487/RFC5595, September 2009, <http://www.rfc-editor.org/info/rfc5595>. [RFC5596] Fairhurst, G., "Datagram Congestion Control Protocol (DCCP) Simultaneous-Open Technique to Facilitate NAT/ Middlebox Traversal",RFC 5596, DOI 10.17487/RFC5596, September 2009, <http://www.rfc-editor.org/info/rfc5596>. [RFC5622] Floyd, S. and E. Kohler, "Profile for Datagram Congestion Control Protocol (DCCP) Congestion ID 4: TCP-Friendly Rate Control for Small Packets (TFRC-SP)",RFC 5622, DOI 10.17487/RFC5622, August 2009, <http://www.rfc-editor.org/info/rfc5622>. [RFC5651] Luby, M., Watson, M., and L. Vicisano, "Layered Coding Transport (LCT) Building Block",RFC 5651, DOI 10.17487/RFC5651, October 2009, <http://www.rfc-editor.org/info/rfc5651>.Fairhurst, et al. Informational [Page 47]
RFC 8095 Transport Services March 2017 [RFC5681] Allman, M., Paxson, V., and E. Blanton, "TCP Congestion Control",RFC 5681, DOI 10.17487/RFC5681, September 2009, <http://www.rfc-editor.org/info/rfc5681>. [RFC5740] Adamson, B., Bormann, C., Handley, M., and J. Macker, "NACK-Oriented Reliable Multicast (NORM) Transport Protocol",RFC 5740, DOI 10.17487/RFC5740, November 2009, <http://www.rfc-editor.org/info/rfc5740>. [RFC5762] Perkins, C., "RTP and the Datagram Congestion Control Protocol (DCCP)",RFC 5762, DOI 10.17487/RFC5762, April 2010, <http://www.rfc-editor.org/info/rfc5762>. [RFC5775] Luby, M., Watson, M., and L. Vicisano, "Asynchronous Layered Coding (ALC) Protocol Instantiation",RFC 5775, DOI 10.17487/RFC5775, April 2010, <http://www.rfc-editor.org/info/rfc5775>. [RFC6056] Larsen, M. and F. Gont, "Recommendations for Transport- Protocol Port Randomization",BCP 156,RFC 6056, DOI 10.17487/RFC6056, January 2011, <http://www.rfc-editor.org/info/rfc6056>. [RFC6083] Tuexen, M., Seggelmann, R., and E. Rescorla, "Datagram Transport Layer Security (DTLS) for Stream Control Transmission Protocol (SCTP)",RFC 6083, DOI 10.17487/RFC6083, January 2011, <http://www.rfc-editor.org/info/rfc6083>. [RFC6093] Gont, F. and A. Yourtchenko, "On the Implementation of the TCP Urgent Mechanism",RFC 6093, DOI 10.17487/RFC6093, January 2011, <http://www.rfc-editor.org/info/rfc6093>. [RFC6101] Freier, A., Karlton, P., and P. Kocher, "The Secure Sockets Layer (SSL) Protocol Version 3.0",RFC 6101, DOI 10.17487/RFC6101, August 2011, <http://www.rfc-editor.org/info/rfc6101>. [RFC6347] Rescorla, E. and N. Modadugu, "Datagram Transport Layer Security Version 1.2",RFC 6347, DOI 10.17487/RFC6347, January 2012, <http://www.rfc-editor.org/info/rfc6347>. [RFC6356] Raiciu, C., Handley, M., and D. Wischik, "Coupled Congestion Control for Multipath Transport Protocols",RFC 6356, DOI 10.17487/RFC6356, October 2011, <http://www.rfc-editor.org/info/rfc6356>.Fairhurst, et al. Informational [Page 48]
RFC 8095 Transport Services March 2017 [RFC6363] Watson, M., Begen, A., and V. Roca, "Forward Error Correction (FEC) Framework",RFC 6363, DOI 10.17487/RFC6363, October 2011, <http://www.rfc-editor.org/info/rfc6363>. [RFC6458] Stewart, R., Tuexen, M., Poon, K., Lei, P., and V. Yasevich, "Sockets API Extensions for the Stream Control Transmission Protocol (SCTP)",RFC 6458, DOI 10.17487/RFC6458, December 2011, <http://www.rfc-editor.org/info/rfc6458>. [RFC6525] Stewart, R., Tuexen, M., and P. Lei, "Stream Control Transmission Protocol (SCTP) Stream Reconfiguration",RFC 6525, DOI 10.17487/RFC6525, February 2012, <http://www.rfc-editor.org/info/rfc6525>. [RFC6582] Henderson, T., Floyd, S., Gurtov, A., and Y. Nishida, "The NewReno Modification to TCP's Fast Recovery Algorithm",RFC 6582, DOI 10.17487/RFC6582, April 2012, <http://www.rfc-editor.org/info/rfc6582>. [RFC6584] Roca, V., "Simple Authentication Schemes for the Asynchronous Layered Coding (ALC) and NACK-Oriented Reliable Multicast (NORM) Protocols",RFC 6584, DOI 10.17487/RFC6584, April 2012, <http://www.rfc-editor.org/info/rfc6584>. [RFC6726] Paila, T., Walsh, R., Luby, M., Roca, V., and R. Lehtonen, "FLUTE - File Delivery over Unidirectional Transport",RFC 6726, DOI 10.17487/RFC6726, November 2012, <http://www.rfc-editor.org/info/rfc6726>. [RFC6773] Phelan, T., Fairhurst, G., and C. Perkins, "DCCP-UDP: A Datagram Congestion Control Protocol UDP Encapsulation for NAT Traversal",RFC 6773, DOI 10.17487/RFC6773, November 2012, <http://www.rfc-editor.org/info/rfc6773>. [RFC6817] Shalunov, S., Hazel, G., Iyengar, J., and M. Kuehlewind, "Low Extra Delay Background Transport (LEDBAT)",RFC 6817, DOI 10.17487/RFC6817, December 2012, <http://www.rfc-editor.org/info/rfc6817>. [RFC6824] Ford, A., Raiciu, C., Handley, M., and O. Bonaventure, "TCP Extensions for Multipath Operation with Multiple Addresses",RFC 6824, DOI 10.17487/RFC6824, January 2013, <http://www.rfc-editor.org/info/rfc6824>.Fairhurst, et al. Informational [Page 49]
RFC 8095 Transport Services March 2017 [RFC6897] Scharf, M. and A. Ford, "Multipath TCP (MPTCP) Application Interface Considerations",RFC 6897, DOI 10.17487/RFC6897, March 2013, <http://www.rfc-editor.org/info/rfc6897>. [RFC6935] Eubanks, M., Chimento, P., and M. Westerlund, "IPv6 and UDP Checksums for Tunneled Packets",RFC 6935, DOI 10.17487/RFC6935, April 2013, <http://www.rfc-editor.org/info/rfc6935>. [RFC6936] Fairhurst, G. and M. Westerlund, "Applicability Statement for the Use of IPv6 UDP Datagrams with Zero Checksums",RFC 6936, DOI 10.17487/RFC6936, April 2013, <http://www.rfc-editor.org/info/rfc6936>. [RFC6951] Tuexen, M. and R. Stewart, "UDP Encapsulation of Stream Control Transmission Protocol (SCTP) Packets for End-Host to End-Host Communication",RFC 6951, DOI 10.17487/RFC6951, May 2013, <http://www.rfc-editor.org/info/rfc6951>. [RFC7053] Tuexen, M., Ruengeler, I., and R. Stewart, "SACK- IMMEDIATELY Extension for the Stream Control Transmission Protocol",RFC 7053, DOI 10.17487/RFC7053, November 2013, <http://www.rfc-editor.org/info/rfc7053>. [RFC7202] Perkins, C. and M. Westerlund, "Securing the RTP Framework: Why RTP Does Not Mandate a Single Media Security Solution",RFC 7202, DOI 10.17487/RFC7202, April 2014, <http://www.rfc-editor.org/info/rfc7202>. [RFC7230] Fielding, R., Ed. and J. Reschke, Ed., "Hypertext Transfer Protocol (HTTP/1.1): Message Syntax and Routing",RFC 7230, DOI 10.17487/RFC7230, June 2014, <http://www.rfc-editor.org/info/rfc7230>. [RFC7231] Fielding, R., Ed. and J. Reschke, Ed., "Hypertext Transfer Protocol (HTTP/1.1): Semantics and Content",RFC 7231, DOI 10.17487/RFC7231, June 2014, <http://www.rfc-editor.org/info/rfc7231>. [RFC7232] Fielding, R., Ed. and J. Reschke, Ed., "Hypertext Transfer Protocol (HTTP/1.1): Conditional Requests",RFC 7232, DOI 10.17487/RFC7232, June 2014, <http://www.rfc-editor.org/info/rfc7232>.Fairhurst, et al. Informational [Page 50]
RFC 8095 Transport Services March 2017 [RFC7233] Fielding, R., Ed., Lafon, Y., Ed., and J. Reschke, Ed., "Hypertext Transfer Protocol (HTTP/1.1): Range Requests",RFC 7233, DOI 10.17487/RFC7233, June 2014, <http://www.rfc-editor.org/info/rfc7233>. [RFC7234] Fielding, R., Ed., Nottingham, M., Ed., and J. Reschke, Ed., "Hypertext Transfer Protocol (HTTP/1.1): Caching",RFC 7234, DOI 10.17487/RFC7234, June 2014, <http://www.rfc-editor.org/info/rfc7234>. [RFC7235] Fielding, R., Ed. and J. Reschke, Ed., "Hypertext Transfer Protocol (HTTP/1.1): Authentication",RFC 7235, DOI 10.17487/RFC7235, June 2014, <http://www.rfc-editor.org/info/rfc7235>. [RFC7301] Friedl, S., Popov, A., Langley, A., and E. Stephan, "Transport Layer Security (TLS) Application-Layer Protocol Negotiation Extension",RFC 7301, DOI 10.17487/RFC7301, July 2014, <http://www.rfc-editor.org/info/rfc7301>. [RFC7323] Borman, D., Braden, B., Jacobson, V., and R. Scheffenegger, Ed., "TCP Extensions for High Performance",RFC 7323, DOI 10.17487/RFC7323, September 2014, <http://www.rfc-editor.org/info/rfc7323>. [RFC7414] Duke, M., Braden, R., Eddy, W., Blanton, E., and A. Zimmermann, "A Roadmap for Transmission Control Protocol (TCP) Specification Documents",RFC 7414, DOI 10.17487/RFC7414, February 2015, <http://www.rfc-editor.org/info/rfc7414>. [RFC7457] Sheffer, Y., Holz, R., and P. Saint-Andre, "Summarizing Known Attacks on Transport Layer Security (TLS) and Datagram TLS (DTLS)",RFC 7457, DOI 10.17487/RFC7457, February 2015, <http://www.rfc-editor.org/info/rfc7457>. [RFC7496] Tuexen, M., Seggelmann, R., Stewart, R., and S. Loreto, "Additional Policies for the Partially Reliable Stream Control Transmission Protocol Extension",RFC 7496, DOI 10.17487/RFC7496, April 2015, <http://www.rfc-editor.org/info/rfc7496>. [RFC7525] Sheffer, Y., Holz, R., and P. Saint-Andre, "Recommendations for Secure Use of Transport Layer Security (TLS) and Datagram Transport Layer Security (DTLS)",BCP 195,RFC 7525, DOI 10.17487/RFC7525, May 2015, <http://www.rfc-editor.org/info/rfc7525>.Fairhurst, et al. Informational [Page 51]
RFC 8095 Transport Services March 2017 [RFC7540] Belshe, M., Peon, R., and M. Thomson, Ed., "Hypertext Transfer Protocol Version 2 (HTTP/2)",RFC 7540, DOI 10.17487/RFC7540, May 2015, <http://www.rfc-editor.org/info/rfc7540>. [RFC8085] Eggert, L., Fairhurst, G., and G. Shepherd, "UDP Usage Guidelines",BCP 145,RFC 8085, DOI 10.17487/RFC8085, March 2017, <http://www.rfc-editor.org/info/rfc8085>. [SCTP-DTLS-ENCAPS] Tuexen, M., Stewart, R., Jesup, R., and S. Loreto, "DTLS Encapsulation of SCTP Packets", Work in Progress,draft-ietf-tsvwg-sctp-dtls-encaps-09, January 2015. [SCTP-NDATA] Stewart, R., Tuexen, M., Loreto, S., and R. Seggelmann, "Stream Schedulers and User Message Interleaving for the Stream Control Transmission Protocol", Work in Progress,draft-ietf-tsvwg-sctp-ndata-08, October 2016. [TCP-SPEC] Eddy, W., Ed., "Transmission Control Protocol Specification", Work in Progress,draft-ietf-tcpm-rfc793bis-04, December 2016. [TLS-1.3] Rescorla, E., "The Transport Layer Security (TLS) Protocol Version 1.3", Work in Progress,draft-ietf-tls-tls13-18, October 2016. [WEBRTC-TRANS] Alvestrand, H.,"Transports for WebRTC", Work in Progress,draft-ietf-rtcweb-transports-17, October 2016. [XHR] van Kesteren, A., Aubourg, J., Song, J., and H. Steen, "XMLHttpRequest Level 1", World Wide Web Consortium NOTE- XMLHttpRequest-20161006, October 2016, <http://www.w3.org/TR/XMLHttpRequest/>.Fairhurst, et al. Informational [Page 52]
RFC 8095 Transport Services March 2017Acknowledgments Thanks to Joe Touch, Michael Welzl, Spencer Dawkins, and the TAPS working group for the comments, feedback, and discussion. This work is supported by the European Commission under grant agreement No. 318627 mPlane and from the Horizon 2020 research and innovation program under grant agreements No. 644334 (NEAT) and No. 688421 (MAMI). This support does not imply endorsement.Contributors In addition to the editors, this document is the work of Brian Adamson, Dragana Damjanovic, Kevin Fall, Simone Ferlin-Oliviera, Ralph Holz, Olivier Mehani, Karen Nielsen, Colin Perkins, Vincent Roca, and Michael Tuexen. oSection 3.2 on MPTCP was contributed by Simone Ferlin-Oliviera (ferlin@simula.no) and Olivier Mehani (olivier.mehani@nicta.com.au). oSection 3.3 on UDP was contributed by Kevin Fall (kfall@kfall.com). oSection 3.5 on SCTP was contributed by Michael Tuexen (tuexen@fh- muenster.de) and Karen Nielsen (karen.nielsen@tieto.com). oSection 3.7 on TLS and DTLS was contributed by Ralph Holz (ralph.holz@nicta.com.au) and Olivier Mehani (olivier.mehani@nicta.com.au). oSection 3.8 on RTP contains contributions from Colin Perkins (csp@csperkins.org). oSection 3.9 on HTTP was contributed by Dragana Damjanovic (ddamjanovic@mozilla.com). oSection 3.10 on FLUTE/ALC was contributed by Vincent Roca (vincent.roca@inria.fr). oSection 3.11 on NORM was contributed by Brian Adamson (brian.adamson@nrl.navy.mil).Fairhurst, et al. Informational [Page 53]
RFC 8095 Transport Services March 2017Authors' Addresses Godred Fairhurst (editor) University of Aberdeen School of Engineering, Fraser Noble Building Aberdeen AB24 3UE Email: gorry@erg.abdn.ac.uk Brian Trammell (editor) ETH Zurich Gloriastrasse 35 8092 Zurich Switzerland Email: ietf@trammell.ch Mirja Kuehlewind (editor) ETH Zurich Gloriastrasse 35 8092 Zurich Switzerland Email: mirja.kuehlewind@tik.ee.ethz.chFairhurst, et al. Informational [Page 54]
[8]ページ先頭