Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]
PROPOSED STANDARD
Network Working Group D. Fowler, EditorRequest for Comments: 2494 Newbridge NetworksCategory: Standards Track January 1999Definitions of Managed Objectsfor the DS0 and DS0 Bundle Interface TypeStatus of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.Copyright Notice Copyright (C) The Internet Society (1999). All Rights Reserved.Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes objects used for managing DS0 and DS0 Bundle interfaces. This document is a companion document with Definitions of Managed Objects for the DS1/E1/DS2/E2 (RFC 2495 [17]), DS3/E3 (RFC 2496 [18]), and the work in progress, SONET/SDH Interface Types. This memo specifies a MIB module in a manner that is both compliant to the SNMPv2 SMI, and semantically identical to the peer SNMPv1 definitions.Table of Contents1 The SNMP Management Framework ................................22 Overview .....................................................32.1 BONDing Terminology ........................................32.2 Use of ifTable for DS0 Layer ...............................32.3 Using ifStackTable .........................................42.3.1 Usage of Channelization for DS3, DS1, DS0 ................62.3.2 Usage of ifIndex Mapping for DS0Bundle ...................73 Overview of the MIB ..........................................73.1 DS0 MIB ....................................................83.2 DS0Bundle MIB ..............................................84 Object Definitions for DS0 ...................................84.1 The DS0 Config Group .......................................9Fowler, Ed. Standards Track [Page 1]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 19994.1.1 The DS0 Configuration Table ..............................94.1.2 The DS0 Channel Mapping Table ............................125 Object Definitions for DS0 Bundle ............................155.1 The DS0 Bundle Config Group ................................155.1.1 The DS0 Bundle Table .....................................155.2 The DS0 Bonding Group ......................................185.2.1 The DS0 Bonding Table ....................................186 Intellectual Property ........................................217 Acknowledgments ..............................................228 References ...................................................229 Security Considerations ......................................2310 Author's Address ............................................2411 Full Copyright Statement ....................................251. The SNMP Management Framework The SNMP Management Framework presently consists of five major components: o An overall architecture, described inRFC 2271 [1]. o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in STD 16,RFC 1155 [2], STD 16,RFC 1212 [3] andRFC 1215 [4]. The second version, called SMIv2, is described inRFC 1902 [5],RFC1903 [6] andRFC 1904 [7]. o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in STD 15,RFC 1157 [8]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described inRFC 1901 [9] andRFC 1906 [10]. The third version of the message protocol is called SNMPv3 and described inRFC 1906 [10],RFC 2272 [11] andRFC 2274 [12]. o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in STD 15,RFC 1157 [8]. A second set of protocol operations and associated PDU formats is described inRFC 1905 [13]. o A set of fundamental applications described inRFC 2273 [14] and the view-based access control mechanism described inRFC 2275 [15]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI.Fowler, Ed. Standards Track [Page 2]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB.2. Overview These objects are used when the particular media being used to realize an interface is a DS0 interface. At present, this applies to these values of the ifType variable in the Internet-standard MIB: ds0 (81) ds0Bundle (82)2.1. BONDing Terminology Please reference The BONDing Spec [20] for definitions of terms used to describe bonding modes.2.2. Use of ifTable for DS0 Layer The following items are defined inRFC 2233 [16]. Only the ifGeneralInformationGroup and ifCounterDiscontinuityGroup need to be supported. ifTable Object Use for DS0 Layer ====================================================================== ifIndex Interface index. ifDescr See interfaces MIB [16]. ifType ds0(81) or ds0Bundle(82). ifSpeed 64000 for ds0 (regardless of the setting of robbed bit signalling) or N*64000 for ds0Bundle. ifPhysAddress The value of the Circuit Identifier. If no Circuit Identifier has been assigned this object should have an octet string with zero length.Fowler, Ed. Standards Track [Page 3]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 ifAdminStatus See interfaces MIB [16]. ifOperStatus See interfaces MIB [16]. ifLastChange See interfaces MIB [16]. ifName See interfaces MIB [16]. ifLinkUpDownTrapEnable Set to disabled(2). Supports read-only access. ifHighSpeed Set to rounded ifSpeed/1000000. ifConnectorPresent Set to false(2).2.3. Using ifStackTable This section describes by example how to use ifStackTable to represent the relationship of ds0 and ds0Bundles with ds1 interfaces. Implementors of the stack table for ds0 and ds0Bundle interfaces should look at the appropriate RFC for the service being stacked on ds0s and ds0Bundles. Examples given below are for illustration purposes only. Example: A Frame Relay Service is being carried on 4 ds0s of a ds1. +---------------------+ | Frame Relay Service | +---------------------+ | +---------------------+ | ds0Bundle | +---------------------+ | | | | +---+ +---+ +---+ +---+ |ds0| |ds0| |ds0| |ds0| +---+ +---+ +---+ +---+ | | | | +---------------------+ | ds1 | +---------------------+ The assignment of the index values could for example be: ifIndex Description 1 FrameRelayService (type 44) 2 ds0Bundle (type 82) 3 ds0 #1 (type 81)Fowler, Ed. Standards Track [Page 4]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 4 ds0 #2 (type 81) 5 ds0 #3 (type 81) 6 ds0 #4 (type 81) 7 ds1 (type 18) The ifStackTable is then used to show the relationships between the various interfaces. ifStackTable Entries HigherLayer LowerLayer 0 1 1 2 2 3 2 4 2 5 2 6 3 7 4 7 5 7 6 7 7 0 In the case where the frameRelayService is using a single ds0, then the ds0Bundle is not required. +---------------------+ | Frame Relay Service | +---------------------+ | +---+ |ds0| +---+ | +---------------------+ | ds1 | +---------------------+ The assignment of the index values could for example be: ifIndex Description 1 FrameRelayService (type 44) 2 ds0 (type 81) 3 ds1 (type 18) The ifStackTable is then used to show the relationships between the various interfaces.Fowler, Ed. Standards Track [Page 5]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 ifStackTable Entries HigherLayer LowerLayer 0 1 1 2 2 3 3 02.3.1. Usage of Channelization for DS3, DS1, DS0 An example is given here to explain the channelization objects in the DS3, DS1, and DS0 MIBs to help the implementor use the objects correctly. Treatment of E3 and E1 would be similar, with the number of DS0s being different depending on the framing of the E1. Timeslot 16 is not created for framing types that do not pass data over it. Assume that a DS3 (with ifIndex 1) is channelized into DS1s (without DS2s). The object dsx3Channelization is set to enabledDs1. There will be 28 DS1s in the ifTable. Assume the entries in the ifTable for the DS1s are created in channel order and the ifIndex values are 2 through 29. In the DS1 MIB, there will be an entry in the dsx1ChanMappingTable for each ds1. The entries will be as follows: dsx1ChanMappingTable Entries ifIndex dsx1Ds1ChannelNumber dsx1ChanMappedIfIndex 1 1 2 1 2 3 ...... 1 28 29 In addition, the DS1s are channelized into DS0s. The object dsx1Channelization is set to enabledDs0 for each DS1. When this object is set to this value, 24 DS0s are created by the agent. There will be 24 DS0s in the ifTable for each DS1. If the dsx1Channelization is set to disabled, the 24 DS0s are destroyed. Assume the entries in the ifTable are created in channel order and the ifIndex values for the DS0s in the first DS1 are 30 through 53. In the DS0 MIB, there will be an entry in the dsx0ChanMappingTable for each DS0. The entries will be as follows:Fowler, Ed. Standards Track [Page 6]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 dsx0ChanMappingTable Entries ifIndex dsx0Ds0ChannelNumber dsx0ChanMappedIfIndex 2 1 30 2 2 31 ...... 2 24 532.3.2. Usage of ifIndex Mapping for DS0Bundle An example is given here to explain the ifIndex mapping objects in the DS0Bundle MIB to help the implementor use the objects correctly. Assume that a DS1 (with ifIndex 1) is channelized into DS0s. There will be 24 DS0s in the ifTable. Assume the entries in the ifTable for the DS0s are created in channel order and the ifIndex values are 2 through 25. Now, assume that there are two bundles on the DS1. The first one uses channels 1 and 2. The second uses channels 3 and 4. There will be two ifTable entries for these bundles, with values of 26 and 27 for ifIndex. There will be an entry in the dsx0BundleTable for each bundle. The entries will be as follows: dsx0BundleTable Entries dsx0BundleIndex dsx0BundleIfIndex 1 26 2 27 There will be an entry in the dsx0ConfigTable for each DS0. The entries will be as follows: dsx0ConfigTable Entries ifIndex dsx0Ds0ChannelNumber dsx0Ds0BundleMappedIfIndex 2 1 26 3 2 26 4 3 27 5 4 27 6 5 0 7 6 0 ...... 25 24 03. Overview of the MIB This document contains 2 MIB modules, the DS0 MIB and the DS0Bundle MIB.Fowler, Ed. Standards Track [Page 7]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 19993.1. DS0 MIB The DS0 MIB is used to represent individual DS0s in a DS1 or E1. Variables in this MIB would be created for each DS0 in the ifTable. This MIB contains the following group: The DS0 Config Group - This group contains configuration information about a particular DS0.3.2. DS0Bundle MIB The DS0Bundle MIB is used to represent collections of DS0s that are used together to carry data within a DS1/E1 at speeds greater than that of a single DS0. DS0Bundles are created on top of DS0s and are represented that way in the ifStackTable. This MIB contains the following groups: The DS0 Bundle Group - This group contains objects used for creating new ds0Bundles. This group is mandatory. The DS0 Bonding Group - This group contains information about bonding for a ds0Bundle, if bonding is enabled. This group is optional.4. Object Definitions for DS0 DS0-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, transmission FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF DisplayString, TruthValue FROM SNMPv2-TC ifIndex, InterfaceIndex, InterfaceIndexOrZero FROM IF-MIB; -- This is the MIB module for the DS0 Interface objects. ds0 MODULE-IDENTITY LAST-UPDATED "9807161630Z" ORGANIZATION "IETF Trunk MIB Working Group" CONTACT-INFO " David Fowler Postal: Newbridge Networks Corporation 600 March Road Kanata, Ontario, Canada K2K 2E6 Tel: +1 613 591 3600Fowler, Ed. Standards Track [Page 8]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 Fax: +1 613 599 3619 E-mail: davef@newbridge.com" DESCRIPTION "The MIB module to describe DS0 interfaces objects." REVISION "9805242010Z" DESCRIPTION "Initial version of the DS0-MIB." ::= { transmission 81 } -- The DS0 Config Group -- Implementation of this group is mandatory for all -- systems that use a DS0 Interface. -- The DS0 Config Group consists of two tables: -- DS0 Configuration Table -- DS0 Channel Mapping Table -- The DS0 Configuration Table dsx0ConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx0ConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DS0 Configuration table." ::= { ds0 1 } dsx0ConfigEntry OBJECT-TYPE SYNTAX Dsx0ConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DS0 Configuration table. There is an entry in this table for each DS0 interface." INDEX { ifIndex } ::= { dsx0ConfigTable 1 } Dsx0ConfigEntry ::= SEQUENCE { dsx0Ds0ChannelNumber INTEGER, dsx0RobbedBitSignalling TruthValue, dsx0CircuitIdentifier DisplayString, dsx0IdleCode INTEGER, dsx0SeizedCode INTEGER,Fowler, Ed. Standards Track [Page 9]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 dsx0ReceivedCode INTEGER, dsx0TransmitCodesEnable TruthValue, dsx0Ds0BundleMappedIfIndex InterfaceIndexOrZero } dsx0Ds0ChannelNumber OBJECT-TYPE SYNTAX INTEGER(0..31) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the channel number of the ds0 on its DS1/E1." ::= { dsx0ConfigEntry 1 } dsx0RobbedBitSignalling OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates if Robbed Bit Signalling is turned on or off for a given ds0. This only applies to DS0s on a DS1 link. For E1 links the value is always off (false)." ::= { dsx0ConfigEntry 2 } dsx0CircuitIdentifier OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting." ::= { dsx0ConfigEntry 3 } dsx0IdleCode OBJECT-TYPE SYNTAX INTEGER(0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the code transmitted in the ABCD bits when the ds0 is not connected and dsx0TransmitCodesEnable is enabled. The object is a bitmap and the various bit positions are: 1 D bit 2 C bit 4 B bit 8 A bit"Fowler, Ed. Standards Track [Page 10]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 ::= { dsx0ConfigEntry 4 } dsx0SeizedCode OBJECT-TYPE SYNTAX INTEGER(0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "This object contains the code transmitted in the ABCD bits when the ds0 is connected and dsx0TransmitCodesEnable is enabled. The object is a bitmap and the various bit positions are: 1 D bit 2 C bit 4 B bit 8 A bit" ::= { dsx0ConfigEntry 5 } dsx0ReceivedCode OBJECT-TYPE SYNTAX INTEGER(0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the code being received in the ABCD bits. The object is a bitmap and the various bit positions are: 1 D bit 2 C bit 4 B bit 8 A bit" ::= { dsx0ConfigEntry 6 } dsx0TransmitCodesEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object determines if the idle and seized codes are transmitted. If the value of this object is true then the codes are transmitted." ::= { dsx0ConfigEntry 7 } dsx0Ds0BundleMappedIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the ifIndex value assigned by the agent for the ds0Bundle(82) ifEntry toFowler, Ed. Standards Track [Page 11]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 which the given ds0(81) ifEntry may belong. If the given ds0(81) ifEntry does not belong to any ds0Bundle(82) ifEntry, then this object has a value of zero. While this object provides information that can also be found in the ifStackTable, it provides this same information with a single table lookup, rather than by walking the ifStackTable to find the possibly non-existent ds0Bundle(82) ifEntry that may be stacked above the given ds0(81) ifTable entry." ::= { dsx0ConfigEntry 8 } -- The DS0 Channel Mapping Table dsx0ChanMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx0ChanMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DS0 Channel Mapping table. This table maps a DS0 channel number on a particular DS1/E1 into an ifIndex." ::= { ds0 3 } dsx0ChanMappingEntry OBJECT-TYPE SYNTAX Dsx0ChanMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DS0 Channel Mapping table. There is an entry in this table corresponding to each ds0 ifEntry within any interface that is channelized to the individual ds0 ifEntry level. This table is intended to facilitate mapping from channelized interface / channel number to DS0 ifEntry. (e.g. mapping (DS1 ifIndex, DS0 Channel Number) -> ifIndex) While this table provides information that can also be found in the ifStackTable and dsx0ConfigTable, it provides this same information with a single table lookup, rather than by walking the ifStackTable to find the various constituent ds0 ifTable entries, and testing variousFowler, Ed. Standards Track [Page 12]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 dsx0ConfigTable entries to check for the entry with the applicable DS0 channel number." INDEX { ifIndex, dsx0Ds0ChannelNumber } ::= { dsx0ChanMappingTable 1 } Dsx0ChanMappingEntry ::= SEQUENCE { dsx0ChanMappedIfIndex InterfaceIndex } dsx0ChanMappedIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the ifIndex value assigned by the agent for the individual ds0 ifEntry that corresponds to the given DS0 channel number (specified by the INDEX element dsx0Ds0ChannelNumber) of the given channelized interface (specified by INDEX element ifIndex)." ::= { dsx0ChanMappingEntry 1 } -- conformance information ds0Conformance OBJECT IDENTIFIER ::= { ds0 2 } ds0Groups OBJECT IDENTIFIER ::= { ds0Conformance 1 } ds0Compliances OBJECT IDENTIFIER ::= { ds0Conformance 2 } -- compliance statements ds0Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for DS0 interfaces." MODULE -- this module MANDATORY-GROUPS { ds0ConfigGroup } OBJECT dsx0RobbedBitSignalling MIN-ACCESS read-only DESCRIPTION "The ability to set RBS is not required." OBJECT dsx0CircuitIdentifier MIN-ACCESS read-only DESCRIPTIONFowler, Ed. Standards Track [Page 13]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 "The ability to set the circuit identifier is not required." OBJECT dsx0IdleCode MIN-ACCESS read-only DESCRIPTION "The ability to set the idle code is not required." OBJECT dsx0SeizedCode MIN-ACCESS read-only DESCRIPTION "The ability to set the seized code is not required." OBJECT dsx0TransmitCodesEnable MIN-ACCESS read-only DESCRIPTION "The ability to enable and disable the transmitting of idle and seized codes is not required." ::= { ds0Compliances 1 } -- units of conformance ds0ConfigGroup OBJECT-GROUP OBJECTS { dsx0Ds0ChannelNumber, dsx0RobbedBitSignalling, dsx0CircuitIdentifier, dsx0IdleCode, dsx0SeizedCode, dsx0ReceivedCode, dsx0TransmitCodesEnable, dsx0Ds0BundleMappedIfIndex, dsx0ChanMappedIfIndex } STATUS current DESCRIPTION "A collection of objects providing configuration information applicable to all DS0 interfaces." ::= { ds0Groups 1 } ENDFowler, Ed. Standards Track [Page 14]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 19995. Object Definitions for DS0 Bundle DS0BUNDLE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, transmission FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF DisplayString, RowStatus, TestAndIncr FROM SNMPv2-TC ifIndex, InterfaceIndex FROM IF-MIB; -- This is the MIB module for the DS0Bundle Interface -- objects. ds0Bundle MODULE-IDENTITY LAST-UPDATED "9807161630Z" ORGANIZATION "IETF Trunk MIB Working Group" CONTACT-INFO " David Fowler Postal: Newbridge Networks Corporation 600 March Road Kanata, Ontario, Canada K2K 2E6 Tel: +1 613 591 3600 Fax: +1 613 599 3619 E-mail: davef@newbridge.com" DESCRIPTION "The MIB module to describe DS0 Bundle interfaces objects." REVISION "9805242010Z" DESCRIPTION "Initial version of the DS0BUNDLE-MIB." ::= { transmission 82 } -- -- The DS0 Bundle Config Group -- -- Implementation of this group is mandatory for all -- systems that use a DS0Bundle Interface. -- -- The DS0 Bundle Config Group consists of one table: -- DS0 Bundle Table -- The DS0 Bundle TableFowler, Ed. Standards Track [Page 15]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 dsx0BundleNextIndex OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to assist the manager in selecting a value for dsx0BundleIndex. Because this object is of syntax TestAndIncr (see the SNMPv2-TC document,RFC 1903) it can also be used to avoid race conditions with multiple managers trying to create rows in the table. If the result of the SET for dsx0BundleNextIndex is not success, this means the value has been changed from index (i.e. another manager used the value), so a new value is required. The algorithm is: done = false while done == false index = GET (dsx0BundleNextIndex.0) SET (dsx0BundleNextIndex.0=index) if (set failed) done = false else SET(dsx0BundleRowStatus.index=createAndGo) if (set failed) done = false else done = true other error handling" ::= { ds0Bundle 2 } dsx0BundleTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx0BundleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an row in this table for each ds0Bundle in the system. This table can be used to (indirectly) create rows in the ifTable with ifType = 'ds0Bundle(82)'." ::= { ds0Bundle 3 } dsx0BundleEntry OBJECT-TYPE SYNTAX Dsx0BundleEntry MAX-ACCESS not-accessible STATUS currentFowler, Ed. Standards Track [Page 16]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 DESCRIPTION "There is a row in entry in this table for each ds0Bundle interface." INDEX { dsx0BundleIndex } ::= { dsx0BundleTable 1 } Dsx0BundleEntry ::= SEQUENCE { dsx0BundleIndex INTEGER, dsx0BundleIfIndex InterfaceIndex, dsx0BundleCircuitIdentifier DisplayString, dsx0BundleRowStatus RowStatus } dsx0BundleIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique identifier for a ds0Bundle. This is not the same value as ifIndex. This table is not indexed by ifIndex because the manager has to choose the index in a createable row and the agent must be allowed to select ifIndex values." ::= { dsx0BundleEntry 1 } dsx0BundleIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex value the agent selected for the (new) ds0Bundle interface." ::= { dsx0BundleEntry 2 } dsx0BundleCircuitIdentifier OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting." ::= { dsx0BundleEntry 3 } dsx0BundleRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-createFowler, Ed. Standards Track [Page 17]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 STATUS current DESCRIPTION "This object is used to create and delete rows in this table." ::= { dsx0BundleEntry 4 } -- The DS0 Bonding Group -- Implementation of this group is optional for all -- systems that use a DS0Bundle Interface. -- The DS0 Bonding Group consists of one table: -- DS0 Bonding Table -- The DS0 Bonding Table dsx0BondingTable OBJECT-TYPE SYNTAX SEQUENCE OF Dsx0BondingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DS0 Bonding table." ::= { ds0Bundle 1 } dsx0BondingEntry OBJECT-TYPE SYNTAX Dsx0BondingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the DS0 Bonding table. There is a row in this table for each DS0Bundle interface." INDEX { ifIndex } ::= { dsx0BondingTable 1 } Dsx0BondingEntry ::= SEQUENCE { dsx0BondMode INTEGER, dsx0BondStatus INTEGER, dsx0BondRowStatus RowStatus } dsx0BondMode OBJECT-TYPE SYNTAX INTEGER { none(1), other(2), mode0(3), mode1(4), mode2(5),Fowler, Ed. Standards Track [Page 18]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 mode3(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates which BONDing mode is used, if any, for a ds0Bundle. Mode0 provides parameter and number exchange with no synchronization. Mode 1 provides parameter and number exchange. Mode 1 also provides synchronization during initialization but does not include inband monitoring. Mode 2 provides all of the above plus inband monitoring. Mode 2 also steals 1/64th of the bandwidth of each channel (thus not supporting n x 56/64 kbit/s data channels for most values of n). Mode 3 provides all of the above, but also provides n x 56/64 kbit/s data channels. Most common implementations of Mode 3 add an extra channel to support the inband monitoring overhead. ModeNone should be used when the interface is not performing bandwidth-on-demand." ::= { dsx0BondingEntry 1 } dsx0BondStatus OBJECT-TYPE SYNTAX INTEGER { idle(1), callSetup(2), dataTransfer(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current status of the bonding call using this ds0Bundle. idle(1) should be used when the bonding mode is set to none(1)." ::= { dsx0BondingEntry 2 } dsx0BondRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create new rows in this table, modify existing rows, and to delete existing rows." ::= { dsx0BondingEntry 3 }Fowler, Ed. Standards Track [Page 19]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 -- conformance information ds0BundleConformance OBJECT IDENTIFIER ::= { ds0Bundle 4 } ds0BundleGroups OBJECT IDENTIFIER ::= { ds0BundleConformance 1 } ds0BundleCompliances OBJECT IDENTIFIER ::= { ds0BundleConformance 2 } -- compliance statements ds0BundleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for DS0Bundle interfaces." MODULE -- this module MANDATORY-GROUPS {ds0BundleConfigGroup } GROUP ds0BondingGroup DESCRIPTION "Implementation of this group is optional for all systems that attach to a DS0Bundle Interface." OBJECT dsx0BundleRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object, and only three of the six enumerated values for the RowStatus textual convention need be supported. Only supporting createAndGo for a creation process prevents the manager from creating an inactive row in the ds0BundleTable. Inactive rows in the ds0BundleTable do not make sense." OBJECT dsx0BundleCircuitIdentifier MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SETFowler, Ed. Standards Track [Page 20]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 operation to this object." ::= { ds0BundleCompliances 1 } -- units of conformance ds0BondingGroup OBJECT-GROUP OBJECTS { dsx0BondMode, dsx0BondStatus, dsx0BondRowStatus } STATUS current DESCRIPTION "A collection of objects providing configuration information applicable to all DS0 interfaces." ::= { ds0BundleGroups 1 } ds0BundleConfigGroup OBJECT-GROUP OBJECTS { dsx0BundleNextIndex, dsx0BundleIfIndex, dsx0BundleCircuitIdentifier, dsx0BundleRowStatus } STATUS current DESCRIPTION "A collection of objects providing the ability to create a new ds0Bundle in the ifTable as well as configuration information about the ds0Bundle." ::= { ds0BundleGroups 2 } END6. Intellectual Property The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found inBCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat.Fowler, Ed. Standards Track [Page 21]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director.7. Acknowledgments This document was produced by the Trunk MIB Working Group.8. References [1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks",RFC 2271, January 1998. [2] Rose, M., and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", STD 16,RFC1155, May 1990. [3] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD 16,RFC 1212, March 1991. [4] Rose, M., "A Convention for Defining Traps for use with the SNMP",RFC 1215, March 1991. [5] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1902, January 1996. [6] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1903, January 1996. [7] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1904, January 1996. [8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", STD 15,RFC 1157, May 1990. [9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Introduction to Community-based SNMPv2",RFC 1901, January 1996. [10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1906, January 1996.Fowler, Ed. Standards Track [Page 22]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 [11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)",RFC 2272, January 1998. [12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)",RFC 2274, January 1998. [13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1905, January 1996. [14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications",RFC2273, January 1998. [15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)",RFC 2275, January 1998. [16] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB using SMIv2",RFC 2233, November 1997. [17] Fowler D., "Definitions of Managed Objects for the DS1, E1, DS2, and E2 Interface Types",RFC 2495, January 1999. [18] Fowler, D., "Definitions of Managed Objects for the DS3/E3 Interface Types",RFC 2496, January 1999. [19] Brown, T., and K. Tesink, "Definitions of Managed Objects for the SONET/SDH Interface Type", Work in Progress. [20] Sharp, H. (Editor), "Interoperability Requirements for Nx56/64 kbit/s Calls", BONDING Spec Version 1.0, BONDING Consortium, Sept 1992.9. Security Considerations SNMPv1 by itself is such an insecure environment. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET (read) the objects in this MIB. It is recommended that the implementors consider the security features as provided by the SNMPv3 framework. Specifically, the use of the User-based Security ModelRFC 2274 [12] and the View-based Access Control ModelRFC 2275 [15] is recommended.Fowler, Ed. Standards Track [Page 23]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 1999 It is then a customer/user responsibility to ensure that the SNMP entity giving access to an instance of this MIB, is properly configured to give access to those objects only to those principals (users) that have legitimate rights to access them. Setting the following objects to an inappropriate value can cause loss of traffic. In the case of dsx0RobbedBitSignalling, for example, the nature of the traffic flowing on the DS0 can be affected. dsx0RobbedBitSignalling dsx0IdleCode dsx0SeizedCode dsx0TransmitCodesEnable dsx0BundleRowStatus dsx0BondMode dsx0BondRowStatus Setting the following objects is mischievous, but not harmful to traffic. dsx0CircuitIdentifier dsx0BundleNextIndex10. Author's Address David Fowler Newbridge Networks 600 March Road Kanata, Ontario, Canada K2K 2E6 Phone: (613) 599-3600, ext 6559 EMail: davef@newbridge.comFowler, Ed. Standards Track [Page 24]
RFC 2494 DSO MIB / DSOBUNDLE MIB January 199911. Full Copyright Statement Copyright (C) The Internet Society (1999). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.Fowler, Ed. Standards Track [Page 25]
[8]ページ先頭