Movatterモバイル変換


[0]ホーム

URL:


[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]

HISTORIC
Network Working Group                                         R. AusteinRequest for Comments: 1611               Epilogue Technology CorporationCategory: Standards Track                                     J. Saperia                                           Digital Equipment Corporation                                                                May 1994DNS Server MIB ExtensionsStatus of this Memo   This document specifies an Internet standards track protocol for the   Internet community, and requests discussion and suggestions for   improvements.  Please refer to the current edition of the "Internet   Official Protocol Standards" (STD 1) for the standardization state   and status of this protocol.  Distribution of this memo is unlimited.Table of Contents1. Introduction ..............................................12. The SNMPv2 Network Management Framework ...................22.1 Object Definitions .......................................23. Overview ..................................................23.1 Resolvers ................................................33.2 Name Servers .............................................33.3 Selected Objects .........................................43.4 Textual Conventions ......................................44. Definitions ...............................................55. Acknowledgements ..........................................286. References ................................................287. Security Considerations ...................................298. Authors' Addresses ........................................301.  Introduction   This memo defines a portion of the Management Information Base (MIB)   for use with network management protocols in the Internet community.   In particular, it describes a set of extensions which instrument DNS   name server functions.  This memo was produced by the DNS working   group.   With the adoption of the Internet-standard Network Management   Framework [4,5,6,7], and with a large number of vendor   implementations of these standards in commercially available   products, it became possible to provide a higher level of effective   network management in TCP/IP-based internets than was previously   available.  With the growth in the use of these standards, it has   become possible to consider the management of other elements of the   infrastructure beyond the basic TCP/IP protocols.  A key element ofAustein & Saperia                                               [Page 1]

RFC 1611               DNS Server MIB Extensions                May 1994   the TCP/IP infrastructure is the DNS.   Up to this point there has been no mechanism to integrate the   management of the DNS with SNMP-based managers.  This memo provides   the mechanisms by which IP-based management stations can effectively   manage DNS name server software in an integrated fashion.   We have defined DNS MIB objects to be used in conjunction with the   Internet MIB to allow access to and control of DNS name server   software via SNMP by the Internet community.2.  The SNMPv2 Network Management Framework   The SNMPv2 Network Management Framework consists of four major   components.  They are:      oRFC 1442 which defines the SMI, the mechanisms used for         describing and naming objects for the purpose of management.      o  STD 17,RFC 1213 defines MIB-II, the core set of managed objects         for the Internet suite of protocols.      oRFC 1445 which defines the administrative and other architectural         aspects of the framework.      oRFC 1448 which defines the protocol used for network access to         managed objects.      The Framework permits new objects to be defined for the purpose of      experimentation and evaluation.2.1.  Object Definitions   Managed objects are accessed via a virtual information store, termed   the Management Information Base or MIB.  Objects in the MIB are   defined using the subset of Abstract Syntax Notation One (ASN.1)   defined in the SMI.  In particular, each object object type is named   by an OBJECT IDENTIFIER, an administratively assigned name.  The   object type together with an object instance serves to uniquely   identify a specific instantiation of the object.  For human   convenience, we often use a textual string, termed the descriptor, to   refer to the object type.3.  Overview   In theory, the DNS world is pretty simple.  There are two kinds of   entities: resolvers and name servers.  Resolvers ask questions.  Name   servers answer them.  The real world, however, is not so simple.Austein & Saperia                                               [Page 2]

RFC 1611               DNS Server MIB Extensions                May 1994   Implementors have made widely differing choices about how to divide   DNS functions between resolvers and servers.  They have also   constructed various sorts of exotic hybrids.  The most difficult task   in defining this MIB was to accommodate this wide range of entities   without having to come up with a separate MIB for each.   We divided up the various DNS functions into two, non-overlapping   classes, called "resolver functions" and "name server functions."  A   DNS entity that performs what we define as resolver functions   contains a resolver, and therefore must implement the MIB groups   required of all resolvers which are defined in a separate MIB Module.   A DNS entity which implements name server functions is considered to   be a name server, and must implement the MIB groups required for name   servers in this module.  If the same piece of software performs both   resolver and server functions, we imagine that it contains both a   resolver and a server and would thus implement both the DNS Server   and DNS Resolver MIBs.3.1.  Resolvers   In our model, a resolver is a program (or piece thereof) which   obtains resource records from servers.  Normally it does so at the   behest of an application, but may also do so as part of its own   operation.  A resolver sends DNS protocol queries and receives DNS   protocol replies.  A resolver neither receives queries nor sends   replies.  A full service resolver is one that knows how to resolve   queries: it obtains the needed resource records by contacting a   server authoritative for the records desired.  A stub resolver does   not know how to resolve queries: it sends all queries to a local name   server, setting the "recursion desired" flag to indicate that it   hopes that the name server will be willing to resolve the query.  A   resolver may (optionally) have a cache for remembering previously   acquired resource records.  It may also have a negative cache for   remembering names or data that have been determined not to exist.3.2.  Name Servers   A name server is a program (or piece thereof) that provides resource   records to resolvers.  All references in this document to "a name   server" imply "the name server's role"; in some cases the name   server's role and the resolver's role might be combined into a single   program.  A name server receives DNS protocol queries and sends DNS   protocol replies.  A name server neither sends queries nor receives   replies.  As a consequence, name servers do not have caches.   Normally, a name server would expect to receive only those queries to   which it could respond with authoritative information.  However, if a   name server receives a query that it cannot respond to with purely   authoritative information, it may choose to try to obtain theAustein & Saperia                                               [Page 3]

RFC 1611               DNS Server MIB Extensions                May 1994   necessary additional information from a resolver which may or may not   be a separate process.3.3.  Selected Objects   Many of the objects included in this memo have been created from   information contained in the DNS specifications [1,2], as amended and   clarified by subsequent host requirements documents [3].  Other   objects have been created based on experience with existing DNS   management tools, expected operational needs, the statistics   generated by existing DNS implementations, and the configuration   files used by existing DNS implementations.  These objects have been   ordered into groups as follows:      o  Server Configuration Group      o  Server Counter Group      o  Server Optional Counter Group      o  Server Zone Group   This information has been converted into a standard form using the   SNMPv2 SMI defined in [9].  For the most part, the descriptions are   influenced by the DNS related RFCs noted above.  For example, the   descriptions for counters used for the various types of queries of   DNS records are influenced by the definitions used for the various   record types found in [2].3.4.  Textual Conventions   Several conceptual data types have been introduced as a textual   conventions in this DNS MIB document.  These additions will   facilitate the common understanding of information used by the DNS.   No changes to the SMI or the SNMP are necessary to support these   conventions.   Readers familiar with MIBs designed to manage entities in the lower   layers of the Internet protocol suite may be surprised at the number   of non-enumerated integers used in this MIB to represent values such   as DNS RR class and type numbers.  The reason for this choice is   simple: the DNS itself is designed as an extensible protocol,   allowing new classes and types of resource records to be added to the   protocol without recoding the core DNS software.  Using non-   enumerated integers to represent these data types in this MIB allows   the MIB to accommodate these changes as well.Austein & Saperia                                               [Page 4]

RFC 1611               DNS Server MIB Extensions                May 19944.  Definitions   DNS-SERVER-MIB DEFINITIONS ::= BEGIN   IMPORTS       mib-2           FROMRFC-1213       MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY,       IpAddress, Counter32, Gauge32           FROM SNMPv2-SMI       TEXTUAL-CONVENTION, RowStatus, DisplayString, TruthValue           FROM SNMPv2-TC       MODULE-COMPLIANCE, OBJECT-GROUP           FROM SNMPv2-CONF;   dns OBJECT-IDENTITY       STATUS  current       DESCRIPTION               "The OID assigned to DNS MIB work by the IANA."       ::= { mib-2 32 }   dnsServMIB MODULE-IDENTITY       LAST-UPDATED "9401282251Z"       ORGANIZATION "IETF DNS Working Group"       CONTACT-INFO               "       Rob Austein               Postal: Epilogue Technology Corporation                       268 Main Street, Suite 283                       North Reading, MA 10864                       US                  Tel: +1 617 245 0804                  Fax: +1 617 245 8122               E-Mail: sra@epilogue.com                       Jon Saperia               Postal: Digital Equipment Corporation                       110 Spit Brook Road                       ZKO1-3/H18                       Nashua, NH 03062-2698                       US                  Tel: +1 603 881 0480                  Fax: +1 603 881 0120                Email: saperia@zko.dec.com"       DESCRIPTION               "The MIB module for entities implementing the server side               of the Domain Name System (DNS) protocol."       ::= { dns 1 }Austein & Saperia                                               [Page 5]

RFC 1611               DNS Server MIB Extensions                May 1994   dnsServMIBObjects       OBJECT IDENTIFIER ::= { dnsServMIB 1 }   -- (Old-style) groups in the DNS server MIB.   dnsServConfig           OBJECT IDENTIFIER ::= { dnsServMIBObjects 1 }   dnsServCounter          OBJECT IDENTIFIER ::= { dnsServMIBObjects 2 }   dnsServOptCounter       OBJECT IDENTIFIER ::= { dnsServMIBObjects 3 }   dnsServZone             OBJECT IDENTIFIER ::= { dnsServMIBObjects 4 }   -- Textual conventions   DnsName ::= TEXTUAL-CONVENTION       -- A DISPLAY-HINT would be nice, but difficult to express.       STATUS  current       DESCRIPTION               "A DNS name is a sequence of labels.  When DNS names are               displayed, the boundaries between labels are typically               indicated by dots (e.g. `Acme' and `COM' are labels in               the name `Acme.COM').  In the DNS protocol, however, no               such separators are needed because each label is encoded               as a length octet followed by the indicated number of               octets of label.  For example, `Acme.COM' is encoded as               the octet sequence { 4, 'A', 'c', 'm', 'e', 3, 'C', 'O',               'M', 0 } (the final 0 is the length of the name of the               root domain, which appears implicitly at the end of any               DNS name).  This MIB uses the same encoding as the DNS               protocol.               A DnsName must always be a fully qualified name.  It is               an error to encode a relative domain name as a DnsName               without first making it a fully qualified name."       REFERENCE               "RFC-1034 section 3.1."       SYNTAX  OCTET STRING (SIZE (0..255))   DnsNameAsIndex ::= TEXTUAL-CONVENTION       STATUS  current       DESCRIPTION               "This textual convention is like a DnsName, but is used               as an index componant in tables.  Alphabetic characters               in names of this type are restricted to uppercase: the               characters 'a' through 'z' are mapped to the characters               'A' through 'Z'.  This restriction is intended to make               the lexical ordering imposed by SNMP useful when applied               to DNS names.               Note that it is theoretically possible for a valid DNSAustein & Saperia                                               [Page 6]

RFC 1611               DNS Server MIB Extensions                May 1994               name to exceed the allowed length of an SNMP object               identifer, and thus be impossible to represent in tables               in this MIB that are indexed by DNS name.  Sampling of               DNS names in current use on the Internet suggests that               this limit does not pose a serious problem in practice."       REFERENCE               "RFC-1034 section 3.1,RFC-1448 section 4.1."       SYNTAX  DnsName   DnsClass ::= TEXTUAL-CONVENTION       DISPLAY-HINT "2d"       STATUS  current       DESCRIPTION               "This data type is used to represent the class values               which appear in Resource Records in the DNS.  A 16-bit               unsigned integer is used to allow room for new classes               of records to be defined.  Existing standard classes are               listed in the DNS specifications."       REFERENCE               "RFC-1035 section 3.2.4."       SYNTAX  INTEGER (0..65535)   DnsType ::= TEXTUAL-CONVENTION       DISPLAY-HINT "2d"       STATUS  current       DESCRIPTION               "This data type is used to represent the type values               which appear in Resource Records in the DNS.  A 16-bit               unsigned integer is used to allow room for new record               types to be defined.  Existing standard types are listed               in the DNS specifications."       REFERENCE               "RFC-1035 section 3.2.2."       SYNTAX  INTEGER (0..65535)   DnsQClass ::= TEXTUAL-CONVENTION       DISPLAY-HINT "2d"       STATUS  current       DESCRIPTION               "This data type is used to represent the QClass values               which appear in Resource Records in the DNS.  A 16-bit               unsigned integer is used to allow room for new QClass               records to be defined.  Existing standard QClasses are               listed in the DNS specification."       REFERENCE               "RFC-1035 section 3.2.5."       SYNTAX  INTEGER (0..65535)Austein & Saperia                                               [Page 7]

RFC 1611               DNS Server MIB Extensions                May 1994   DnsQType ::= TEXTUAL-CONVENTION       DISPLAY-HINT "2d"       STATUS  current       DESCRIPTION               "This data type is used to represent the QType values               which appear in Resource Records in the DNS.  A 16-bit               unsigned integer is used to allow room for new QType               records to be defined.  Existing standard QTypes are               listed in the DNS specification."       REFERENCE               "RFC-1035 section 3.2.3."       SYNTAX  INTEGER (0..65535)   DnsTime ::= TEXTUAL-CONVENTION       DISPLAY-HINT "4d"       STATUS  current       DESCRIPTION               "DnsTime values are 32-bit unsigned integers which               measure time in seconds."       REFERENCE               "RFC-1035."       SYNTAX  Gauge32   DnsOpCode ::= TEXTUAL-CONVENTION       STATUS  current       DESCRIPTION               "This textual convention is used to represent the DNS               OPCODE values used in the header section of DNS               messages.  Existing standard OPCODE values are listed in               the DNS specifications."       REFERENCE               "RFC-1035 section 4.1.1."       SYNTAX  INTEGER (0..15)   DnsRespCode ::= TEXTUAL-CONVENTION       STATUS  current       DESCRIPTION               "This data type is used to represent the DNS RCODE value               in DNS response messages.  Existing standard RCODE               values are listed in the DNS specifications."       REFERENCE               "RFC-1035 section 4.1.1."       SYNTAX  INTEGER (0..15)Austein & Saperia                                               [Page 8]

RFC 1611               DNS Server MIB Extensions                May 1994   -- Server Configuration Group   dnsServConfigImplementIdent OBJECT-TYPE       SYNTAX      DisplayString       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "The implementation identification string for the DNS               server software in use on the system, for example;               `FNS-2.1'"       ::= { dnsServConfig 1 }   dnsServConfigRecurs  OBJECT-TYPE       SYNTAX      INTEGER { available(1),                             restricted(2),                             unavailable(3) }       MAX-ACCESS  read-write       STATUS      current       DESCRIPTION               "This represents the recursion services offered by this               name server.  The values that can be read or written               are:               available(1) - performs recursion on requests from               clients.               restricted(2) - recursion is performed on requests only               from certain clients, for example; clients on an access               control list.               unavailable(3) - recursion is not available."        ::= { dnsServConfig 2 }   dnsServConfigUpTime OBJECT-TYPE       SYNTAX      DnsTime       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "If the server has a persistent state (e.g., a process),               this value will be the time elapsed since it started.               For software without persistant state, this value will               be zero."       ::= { dnsServConfig 3 }   dnsServConfigResetTime OBJECT-TYPE       SYNTAX      DnsTime       MAX-ACCESS  read-only       STATUS      currentAustein & Saperia                                               [Page 9]

RFC 1611               DNS Server MIB Extensions                May 1994       DESCRIPTION               "If the server has a persistent state (e.g., a process)               and supports a `reset' operation (e.g., can be told to               re-read configuration files), this value will be the               time elapsed since the last time the name server was               `reset.'  For software that does not have persistence or               does not support a `reset' operation, this value will be               zero."       ::= { dnsServConfig 4 }   dnsServConfigReset OBJECT-TYPE       SYNTAX      INTEGER { other(1),                             reset(2),                             initializing(3),                             running(4) }       MAX-ACCESS  read-write       STATUS      current       DESCRIPTION               "Status/action object to reinitialize any persistant name               server state.  When set to reset(2), any persistant               name server state (such as a process) is reinitialized as               if the name server had just been started.  This value               will never be returned by a read operation.  When read,               one of the following values will be returned:                   other(1) - server in some unknown state;                   initializing(3) - server (re)initializing;                   running(4) - server currently running."       ::= { dnsServConfig 5 }   -- Server Counter Group   dnsServCounterAuthAns OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries which were authoritatively answered."       ::= { dnsServCounter 2 }   dnsServCounterAuthNoNames OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries for which `authoritative no such name'               responses were made."       ::= { dnsServCounter 3 }Austein & Saperia                                              [Page 10]

RFC 1611               DNS Server MIB Extensions                May 1994   dnsServCounterAuthNoDataResps OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries for which `authoritative no such data'               (empty answer) responses were made."       ::= { dnsServCounter 4 }   dnsServCounterNonAuthDatas OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries which were non-authoritatively               answered (cached data)."       ::= { dnsServCounter 5 }   dnsServCounterNonAuthNoDatas OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries which were non-authoritatively               answered with no data (empty answer)."       ::= { dnsServCounter 6 }   dnsServCounterReferrals OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests that were referred to other servers."       ::= { dnsServCounter 7 }   dnsServCounterErrors OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests the server has processed that were               answered with errors (RCODE values other than 0 and 3)."       REFERENCE               "RFC-1035 section 4.1.1."       ::= { dnsServCounter 8 }   dnsServCounterRelNames OBJECT-TYPE       SYNTAX      Counter32Austein & Saperia                                              [Page 11]

RFC 1611               DNS Server MIB Extensions                May 1994       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests received by the server for names that               are only 1 label long (text form - no internal dots)."       ::= { dnsServCounter 9 }   dnsServCounterReqRefusals OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of DNS requests refused by the server."       ::= { dnsServCounter 10 }   dnsServCounterReqUnparses OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests received which were unparseable."       ::= { dnsServCounter 11 }   dnsServCounterOtherErrors OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests which were aborted for other (local)               server errors."       ::= { dnsServCounter 12 }   -- DNS Server Counter Table   dnsServCounterTable OBJECT-TYPE       SYNTAX      SEQUENCE OF DnsServCounterEntry       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "Counter information broken down by DNS class and type."       ::= { dnsServCounter 13 }   dnsServCounterEntry OBJECT-TYPE       SYNTAX      DnsServCounterEntry       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "This table contains count information for each DNS classAustein & Saperia                                              [Page 12]

RFC 1611               DNS Server MIB Extensions                May 1994               and type value known to the server.  The index allows               management software to to create indices to the table to               get the specific information desired, e.g., number of               queries over UDP for records with type value `A' which               came to this server.  In order to prevent an               uncontrolled expansion of rows in the table; if               dnsServCounterRequests is 0 and dnsServCounterResponses               is 0, then the row does not exist and `no such' is               returned when the agent is queried for such instances."       INDEX     { dnsServCounterOpCode,                   dnsServCounterQClass,                   dnsServCounterQType,                   dnsServCounterTransport }       ::= { dnsServCounterTable 1 }   DnsServCounterEntry ::=       SEQUENCE {           dnsServCounterOpCode               DnsOpCode,           dnsServCounterQClass               DnsClass,           dnsServCounterQType               DnsType,           dnsServCounterTransport               INTEGER,           dnsServCounterRequests               Counter32,           dnsServCounterResponses               Counter32           }   dnsServCounterOpCode OBJECT-TYPE       SYNTAX      DnsOpCode       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "The DNS OPCODE being counted in this row of the table."       ::= { dnsServCounterEntry 1 }   dnsServCounterQClass OBJECT-TYPE       SYNTAX      DnsClass       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "The class of record being counted in this row of the               table."       ::= { dnsServCounterEntry 2 }Austein & Saperia                                              [Page 13]

RFC 1611               DNS Server MIB Extensions                May 1994   dnsServCounterQType OBJECT-TYPE       SYNTAX      DnsType       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "The type of record which is being counted in this row in               the table."       ::= { dnsServCounterEntry 3 }   dnsServCounterTransport OBJECT-TYPE       SYNTAX      INTEGER { udp(1), tcp(2), other(3) }       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "A value of udp(1) indicates that the queries reported on               this row were sent using UDP.               A value of tcp(2) indicates that the queries reported on               this row were sent using TCP.               A value of other(3) indicates that the queries reported               on this row were sent using a transport that was neither               TCP nor UDP."       ::= { dnsServCounterEntry 4 }   dnsServCounterRequests OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests (queries) that have been recorded in               this row of the table."       ::= { dnsServCounterEntry 5 }   dnsServCounterResponses OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of responses made by the server since               initialization for the kind of query identified on this               row of the table."       ::= { dnsServCounterEntry 6 }Austein & Saperia                                              [Page 14]

RFC 1611               DNS Server MIB Extensions                May 1994   -- Server Optional Counter Group   -- The Server Optional Counter Group is intended for those systems   -- which make distinctions between the different sources of the DNS   -- queries as defined below.   --   -- Objects in this group are implemented on servers which distinguish   -- between queries which originate from the same host as the server,   -- queries from one of an arbitrary group of hosts that are on an   -- access list defined by the server, and queries from hosts that do   -- not fit either of these descriptions.   --   -- The objects found in the Server Counter group are totals.  Thus if   -- one wanted to identify, for example, the number of queries from   -- `remote' hosts which have been given authoritative answers, one   -- would subtract the current values of ServOptCounterFriendsAuthAns   -- and ServOptCounterSelfAuthAns from servCounterAuthAns.   --   -- The purpose of these distinctions is to allow for implementations   -- to group queries and responses on this basis.  One way in which   -- servers may make these distinctions is by looking at the source IP   -- address of the DNS query.  If the source of the query is `your   -- own' then the query should be counted as `yourself' (local host).   -- If the source of the query matches an `access list,' the query   -- came from a friend.  What constitutes an `access list' is   -- implementation dependent and could be as simple as a rule that all   -- hosts on the same IP network as the DNS server are classed   -- `friends.'   --   -- In order to avoid double counting, the following rules apply:   --   -- 1. No host is in more than one of the three groups defined above.   --   -- 2. All queries from the local host are always counted in the   --    `yourself' group regardless of what the access list, if any,   --    says.   --   -- 3. The access list should not define `your friends' in such a way   --    that it includes all hosts.   That is, not everybody is your   --    `friend.'   dnsServOptCounterSelfAuthAns OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests the server has processed which               originated from a resolver on the same host for whichAustein & Saperia                                              [Page 15]

RFC 1611               DNS Server MIB Extensions                May 1994               there has been an authoritative answer."       ::= { dnsServOptCounter 1 }   dnsServOptCounterSelfAuthNoNames OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests the server has processed which               originated from a resolver on the same host for which               there has been an authoritative no such name answer               given."       ::= { dnsServOptCounter 2 }   dnsServOptCounterSelfAuthNoDataResps OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests the server has processed which               originated from a resolver on the same host for which               there has been an authoritative no such data answer               (empty answer) made."       ::= { dnsServOptCounter 3 }   dnsServOptCounterSelfNonAuthDatas OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests the server has processed which               originated from a resolver on the same host for which a               non-authoritative answer (cached data) was made."       ::= { dnsServOptCounter 4 }   dnsServOptCounterSelfNonAuthNoDatas OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests the server has processed which               originated from a resolver on the same host for which a               `non-authoritative, no such data' response was made               (empty answer)."       ::= { dnsServOptCounter 5 }   dnsServOptCounterSelfReferrals OBJECT-TYPE       SYNTAX      Counter32Austein & Saperia                                              [Page 16]

RFC 1611               DNS Server MIB Extensions                May 1994       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries the server has processed which               originated from a resolver on the same host and were               referred to other servers."       ::= { dnsServOptCounter 6 }   dnsServOptCounterSelfErrors OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests the server has processed which               originated from a resolver on the same host which have               been answered with errors (RCODEs other than 0 and 3)."       REFERENCE               "RFC-1035 section 4.1.1."       ::= { dnsServOptCounter 7 }   dnsServOptCounterSelfRelNames OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests received for names that are only 1               label long (text form - no internal dots) the server has               processed which originated from a resolver on the same               host."       ::= { dnsServOptCounter 8 }   dnsServOptCounterSelfReqRefusals OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of DNS requests refused by the server which               originated from a resolver on the same host."       ::= { dnsServOptCounter 9 }   dnsServOptCounterSelfReqUnparses OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests received which were unparseable and               which originated from a resolver on the same host."       ::= { dnsServOptCounter 10 }Austein & Saperia                                              [Page 17]

RFC 1611               DNS Server MIB Extensions                May 1994   dnsServOptCounterSelfOtherErrors OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests which were aborted for other (local)               server errors and which originated on the same host."       ::= { dnsServOptCounter 11 }   dnsServOptCounterFriendsAuthAns OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries originating from friends which were               authoritatively answered.  The definition of friends is               a locally defined matter."       ::= { dnsServOptCounter 12 }   dnsServOptCounterFriendsAuthNoNames OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries originating from friends, for which               authoritative `no such name' responses were made.  The               definition of friends is a locally defined matter."       ::= { dnsServOptCounter 13 }   dnsServOptCounterFriendsAuthNoDataResps OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries originating from friends for which               authoritative no such data (empty answer) responses were               made.  The definition of friends is a locally defined               matter."       ::= { dnsServOptCounter 14 }   dnsServOptCounterFriendsNonAuthDatas OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries originating from friends which were               non-authoritatively answered (cached data). The               definition of friends is a locally defined matter."Austein & Saperia                                              [Page 18]

RFC 1611               DNS Server MIB Extensions                May 1994       ::= { dnsServOptCounter 15 }   dnsServOptCounterFriendsNonAuthNoDatas OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of queries originating from friends which were               non-authoritatively answered with no such data (empty               answer)."       ::= { dnsServOptCounter 16 }   dnsServOptCounterFriendsReferrals OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests which originated from friends that               were referred to other servers.  The definition of               friends is a locally defined matter."       ::= { dnsServOptCounter 17 }   dnsServOptCounterFriendsErrors OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests the server has processed which               originated from friends and were answered with errors               (RCODE values other than 0 and 3).  The definition of               friends is a locally defined matter."       REFERENCE               "RFC-1035 section 4.1.1."       ::= { dnsServOptCounter 18 }   dnsServOptCounterFriendsRelNames OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests received for names from friends that               are only 1 label long (text form - no internal dots) the               server has processed."       ::= { dnsServOptCounter 19 }   dnsServOptCounterFriendsReqRefusals OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-onlyAustein & Saperia                                              [Page 19]

RFC 1611               DNS Server MIB Extensions                May 1994       STATUS      current       DESCRIPTION               "Number of DNS requests refused by the server which were               received from `friends'."       ::= { dnsServOptCounter 20 }   dnsServOptCounterFriendsReqUnparses OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests received which were unparseable and               which originated from `friends'."       ::= { dnsServOptCounter 21 }   dnsServOptCounterFriendsOtherErrors OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Number of requests which were aborted for other (local)               server errors and which originated from `friends'."       ::= { dnsServOptCounter 22 }   -- Server Zone Group   -- DNS Management Zone Configuration Table   -- This table contains zone configuration information.   dnsServZoneTable OBJECT-TYPE       SYNTAX      SEQUENCE OF DnsServZoneEntry       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "Table of zones for which this name server provides               information.  Each of the zones may be loaded from stable               storage via an implementation-specific mechanism or may               be obtained from another name server via a zone transfer.               If name server doesn't load any zones, this table is               empty."       ::= { dnsServZone 1 }   dnsServZoneEntry OBJECT-TYPE       SYNTAX      DnsServZoneEntry       MAX-ACCESS  not-accessibleAustein & Saperia                                              [Page 20]

RFC 1611               DNS Server MIB Extensions                May 1994       STATUS      current       DESCRIPTION               "An entry in the name server zone table.  New rows may be               added either via SNMP or by the name server itself."       INDEX     { dnsServZoneName,                   dnsServZoneClass }       ::= { dnsServZoneTable 1 }   DnsServZoneEntry ::=       SEQUENCE {           dnsServZoneName               DnsNameAsIndex,           dnsServZoneClass               DnsClass,           dnsServZoneLastReloadSuccess               DnsTime,           dnsServZoneLastReloadAttempt               DnsTime,           dnsServZoneLastSourceAttempt               IpAddress,           dnsServZoneStatus               RowStatus,           dnsServZoneSerial               Counter32,           dnsServZoneCurrent               TruthValue,           dnsServZoneLastSourceSuccess               IpAddress       }   dnsServZoneName OBJECT-TYPE       SYNTAX      DnsNameAsIndex       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "DNS name of the zone described by this row of the table.               This is the owner name of the SOA RR that defines the               top of the zone. This is name is in uppercase:               characters 'a' through 'z' are mapped to 'A' through 'Z'               in order to make the lexical ordering useful."       ::= { dnsServZoneEntry 1 }   dnsServZoneClass OBJECT-TYPE       SYNTAX      DnsClass       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "DNS class of the RRs in this zone."Austein & Saperia                                              [Page 21]

RFC 1611               DNS Server MIB Extensions                May 1994       ::= { dnsServZoneEntry 2 }   dnsServZoneLastReloadSuccess OBJECT-TYPE       SYNTAX      DnsTime       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Elapsed time in seconds since last successful reload of               this zone."       ::= { dnsServZoneEntry 3 }   dnsServZoneLastReloadAttempt OBJECT-TYPE       SYNTAX      DnsTime       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Elapsed time in seconds since last attempted reload of               this zone."       ::= { dnsServZoneEntry 4 }   dnsServZoneLastSourceAttempt OBJECT-TYPE       SYNTAX      IpAddress       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "IP address of host from which most recent zone transfer               of this zone was attempted.  This value should match the               value of dnsServZoneSourceSuccess if the attempt was               succcessful.  If zone transfer has not been attempted               within the memory of this name server, this value should               be 0.0.0.0."       ::= { dnsServZoneEntry 5 }   dnsServZoneStatus OBJECT-TYPE       SYNTAX      RowStatus       MAX-ACCESS  read-create       STATUS      current       DESCRIPTION               "The status of the information represented in this row of               the table."       ::= { dnsServZoneEntry 6 }   dnsServZoneSerial OBJECT-TYPE       SYNTAX      Counter32       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Zone serial number (from the SOA RR) of the zoneAustein & Saperia                                              [Page 22]

RFC 1611               DNS Server MIB Extensions                May 1994               represented by this row of the table.  If the zone has               not been successfully loaded within the memory of this               name server, the value of this variable is zero."       ::= { dnsServZoneEntry 7 }   dnsServZoneCurrent OBJECT-TYPE       SYNTAX      TruthValue       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "Whether the server's copy of the zone represented by               this row of the table is currently valid.  If the zone               has never been successfully loaded or has expired since               it was last succesfully loaded, this variable will have               the value false(2), otherwise this variable will have               the value true(1)."       ::= { dnsServZoneEntry 8 }   dnsServZoneLastSourceSuccess OBJECT-TYPE       SYNTAX      IpAddress       MAX-ACCESS  read-only       STATUS      current       DESCRIPTION               "IP address of host which was the source of the most               recent successful zone transfer for this zone.  If               unknown (e.g., zone has never been successfully               transfered) or irrelevant (e.g., zone was loaded from               stable storage), this value should be 0.0.0.0."       ::= { dnsServZoneEntry 9 }   -- DNS Zone Source Table   dnsServZoneSrcTable OBJECT-TYPE       SYNTAX      SEQUENCE OF DnsServZoneSrcEntry       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "This table is a list of IP addresses from which the               server will attempt to load zone information using DNS               zone transfer operations.  A reload may occur due to SNMP               operations that create a row in dnsServZoneTable or a               SET to object dnsServZoneReload.  This table is only               used when the zone is loaded via zone transfer."       ::= { dnsServZone 2 }   dnsServZoneSrcEntry OBJECT-TYPE       SYNTAX      DnsServZoneSrcEntry       MAX-ACCESS  not-accessibleAustein & Saperia                                              [Page 23]

RFC 1611               DNS Server MIB Extensions                May 1994       STATUS      current       DESCRIPTION               "An entry in the name server zone source table."       INDEX     { dnsServZoneSrcName,                   dnsServZoneSrcClass,                   dnsServZoneSrcAddr }       ::= { dnsServZoneSrcTable 1 }   DnsServZoneSrcEntry ::=       SEQUENCE {           dnsServZoneSrcName               DnsNameAsIndex,           dnsServZoneSrcClass               DnsClass,           dnsServZoneSrcAddr               IpAddress,           dnsServZoneSrcStatus               RowStatus       }   dnsServZoneSrcName OBJECT-TYPE       SYNTAX      DnsNameAsIndex       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "DNS name of the zone to which this entry applies."       ::= { dnsServZoneSrcEntry 1 }   dnsServZoneSrcClass OBJECT-TYPE       SYNTAX      DnsClass       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "DNS class of zone to which this entry applies."       ::= { dnsServZoneSrcEntry 2 }   dnsServZoneSrcAddr OBJECT-TYPE       SYNTAX      IpAddress       MAX-ACCESS  not-accessible       STATUS      current       DESCRIPTION               "IP address of name server host from which this zone               might be obtainable."       ::= { dnsServZoneSrcEntry 3 }   dnsServZoneSrcStatus OBJECT-TYPE       SYNTAX      RowStatus       MAX-ACCESS  read-createAustein & Saperia                                              [Page 24]

RFC 1611               DNS Server MIB Extensions                May 1994       STATUS      current       DESCRIPTION               "The status of the information represented in this row of               the table."       ::= { dnsServZoneSrcEntry 4 }   -- SNMPv2 groups.   dnsServMIBGroups        OBJECT IDENTIFIER ::= { dnsServMIB 2 }   dnsServConfigGroup OBJECT-GROUP       OBJECTS   { dnsServConfigImplementIdent,                   dnsServConfigRecurs,                   dnsServConfigUpTime,                   dnsServConfigResetTime,                   dnsServConfigReset }       STATUS      current       DESCRIPTION               "A collection of objects providing basic configuration               control of a DNS name server."       ::= { dnsServMIBGroups 1 }   dnsServCounterGroup OBJECT-GROUP       OBJECTS   { dnsServCounterAuthAns,                   dnsServCounterAuthNoNames,                   dnsServCounterAuthNoDataResps,                   dnsServCounterNonAuthDatas,                   dnsServCounterNonAuthNoDatas,                   dnsServCounterReferrals,                   dnsServCounterErrors,                   dnsServCounterRelNames,                   dnsServCounterReqRefusals,                   dnsServCounterReqUnparses,                   dnsServCounterOtherErrors,                   dnsServCounterOpCode,                   dnsServCounterQClass,                   dnsServCounterQType,                   dnsServCounterTransport,                   dnsServCounterRequests,                   dnsServCounterResponses }       STATUS      current       DESCRIPTION               "A collection of objects providing basic instrumentation               of a DNS name server."       ::= { dnsServMIBGroups 2 }Austein & Saperia                                              [Page 25]

RFC 1611               DNS Server MIB Extensions                May 1994   dnsServOptCounterGroup OBJECT-GROUP       OBJECTS   { dnsServOptCounterSelfAuthAns,                   dnsServOptCounterSelfAuthNoNames,                   dnsServOptCounterSelfAuthNoDataResps,                   dnsServOptCounterSelfNonAuthDatas,                   dnsServOptCounterSelfNonAuthNoDatas,                   dnsServOptCounterSelfReferrals,                   dnsServOptCounterSelfErrors,                   dnsServOptCounterSelfRelNames,                   dnsServOptCounterSelfReqRefusals,                   dnsServOptCounterSelfReqUnparses,                   dnsServOptCounterSelfOtherErrors,                   dnsServOptCounterFriendsAuthAns,                   dnsServOptCounterFriendsAuthNoNames,                   dnsServOptCounterFriendsAuthNoDataResps,                   dnsServOptCounterFriendsNonAuthDatas,                   dnsServOptCounterFriendsNonAuthNoDatas,                   dnsServOptCounterFriendsReferrals,                   dnsServOptCounterFriendsErrors,                   dnsServOptCounterFriendsRelNames,                   dnsServOptCounterFriendsReqRefusals,                   dnsServOptCounterFriendsReqUnparses,                   dnsServOptCounterFriendsOtherErrors }       STATUS      current       DESCRIPTION               "A collection of objects providing extended               instrumentation of a DNS name server."       ::= { dnsServMIBGroups 3 }   dnsServZoneGroup OBJECT-GROUP       OBJECTS   { dnsServZoneName,                   dnsServZoneClass,                   dnsServZoneLastReloadSuccess,                   dnsServZoneLastReloadAttempt,                   dnsServZoneLastSourceAttempt,                   dnsServZoneLastSourceSuccess,                   dnsServZoneStatus,                   dnsServZoneSerial,                   dnsServZoneCurrent,                   dnsServZoneSrcName,                   dnsServZoneSrcClass,                   dnsServZoneSrcAddr,                   dnsServZoneSrcStatus }       STATUS      current       DESCRIPTION               "A collection of objects providing configuration control               of a DNS name server which loads authoritative zones."       ::= { dnsServMIBGroups 4 }Austein & Saperia                                              [Page 26]

RFC 1611               DNS Server MIB Extensions                May 1994   -- Compliances.   dnsServMIBCompliances OBJECT IDENTIFIER ::= { dnsServMIB 3 }   dnsServMIBCompliance MODULE-COMPLIANCE       STATUS      current       DESCRIPTION               "The compliance statement for agents implementing the DNS               name server MIB extensions."       MODULE -- This MIB module           MANDATORY-GROUPS { dnsServConfigGroup, dnsServCounterGroup }           GROUP   dnsServOptCounterGroup           DESCRIPTION               "The server optional counter group is unconditionally               optional."           GROUP   dnsServZoneGroup           DESCRIPTION               "The server zone group is mandatory for any name server               that acts as an authoritative server for any DNS zone."           OBJECT  dnsServConfigRecurs           MIN-ACCESS      read-only           DESCRIPTION               "This object need not be writable."           OBJECT  dnsServConfigReset           MIN-ACCESS      read-only           DESCRIPTION               "This object need not be writable."       ::= { dnsServMIBCompliances 1 }   ENDAustein & Saperia                                              [Page 27]

RFC 1611               DNS Server MIB Extensions                May 19945.  Acknowledgements   This document is the result of work undertaken the by DNS working   group.  The authors would particularly like to thank the following   people for their contributions to this document: Philip Almquist,   Frank Kastenholz (FTP Software), Joe Peck (DEC), Dave Perkins   (SynOptics), Win Treese (DEC), and Mimi Zohar (IBM).6.  References   [1] Mockapetris, P., "Domain Names -- Concepts and Facilities", STD       13,RFC 1034, USC/Information Sciences Institute, November 1987.   [2] Mockapetris, P., "Domain Names -- Implementation and       Specification", STD 13,RFC 1035, USC/Information Sciences       Institute, November 1987.   [3] Braden, R., Editor, "Requirements for Internet Hosts --       Application and Support, STD 3,RFC 1123, USC/Information       Sciences Institute, October 1989.   [4] Rose, M., and K. McCloghrie, "Structure and Identification of       Management Information for TCP/IP-based internets", STD 16,RFC1155, Performance Systems International, Hughes LAN Systems, May       1990.   [5] McCloghrie, K., and M. Rose, "Management Information Base for       Network Management of TCP/IP-based internets",RFC 1156, Hughes       LAN Systems, Performance Systems International, May 1990.   [6] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple       Network Management Protocol", STD 15,RFC 1157, SNMP Research,       Performance Systems International, Performance Systems       International, MIT Laboratory for Computer Science, May 1990.   [7] Rose, M., and K. McCloghrie, Editors, "Concise MIB Definitions",       STD 16,RFC 1212, Performance Systems International, Hughes LAN       Systems, March 1991.   [8] McCloghrie, K., and M. Rose, Editors, "Management Information       Base for Network Management of TCP/IP-based internets: MIB-II",       STD 17,RFC 1213, Hughes LAN Systems, Performance Systems       International, March 1991.   [9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure       of Management Information for version 2 of the Simple Network       Management Protocol (SNMPv2)",RFC 1442, SNMP Research, Inc.,       Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie MellonAustein & Saperia                                              [Page 28]

RFC 1611               DNS Server MIB Extensions                May 1994       University, April 1993.  [10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual       Conventions for version 2 of the the Simple Network Management       Protocol (SNMPv2)",RFC 1443, SNMP Research, Inc., Hughes LAN       Systems, Dover Beach Consulting, Inc., Carnegie Mellon       University, April 1993.  [11] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,       "Conformance Statements for version 2 of the the Simple Network       Management Protocol (SNMPv2)",RFC 1444, SNMP Research, Inc.,       Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon       University, April 1993.  [12] Galvin, J., and K. McCloghrie, "Administrative Model for version       2 of the Simple Network Management Protocol (SNMPv2)",RFC 1445,       Trusted Information Systems, Hughes LAN Systems, April 1993.  [13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol       Operations for version 2 of the Simple Network Management       Protocol (SNMPv2)",RFC 1448, SNMP Research, Inc., Hughes LAN       Systems, Dover Beach Consulting, Inc., Carnegie Mellon       University, April 1993.  [14] "Information processing systems - Open Systems Interconnection -       Specification of Abstract Syntax Notation One (ASN.1)",       International Organization for Standardization, International       Standard 8824, December 1987.7.  Security Considerations   Security issues are not discussed in this memo.Austein & Saperia                                              [Page 29]

RFC 1611               DNS Server MIB Extensions                May 19948.  Authors' Addresses   Rob Austein   Epilogue Technology Corporation   268 Main Street, Suite 283   North Reading, MA 01864   USA   Phone: +1-617-245-0804   Fax:   +1-617-245-8122   EMail: sra@epilogue.com   Jon Saperia   Digital Equipment Corporation   110 Spit Brook Road   ZKO1-3/H18   Nashua, NH 03062-2698   USA   Phone: +1-603-881-0480   Fax:   +1-603-881-0120   EMail: saperia@zko.dec.comAustein & Saperia                                              [Page 30]

[8]ページ先頭

©2009-2025 Movatter.jp