Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|PDF|HTML] [Tracker] [IPR] [Info page]
UNKNOWN
Network Working Group J. WinettRequest for Comments: 452 JMWNIC: 14136 8 February 1973TELNET Command at Host LL The attached writeup documents the use of the TELNET command at Host LL for uses under the CP/CMS time-sharing system. This command provides for use in a HALF DUPLEX or FULL DUPLEX mode and can be used with ASCII codes or with EBCDIC codes (i.e., transparent mode). The keyboard conventions allow for entering all ASCII codes using a CONTROL character followed by another character for the codes not present on an IBM 2741 terminal. In addition a number of local TELNET control commands have been defined which allows the mode of operation to be changed, the redefinition of special characters, the sending of TELNET control codes, as well as for obtaining input from a file instead of from the terminal. These later features provide for a rudimentary file transfer facility. This material has not been reviewed for public release and is intended only for use with the ARPA network. It should not be quoted or cited in any publication not related to the ARPA network. TELNET Purpose: To access another terminal oriented system on the ARPA network. Format: TELNET host <tag> RESUME EBCDIC HALFDUP 1 OPEN ASCII FULLDUP host - either the hexadecimal code for a foreign network service site or a standard mnemonic for a foreign site. See Figure 1. tag - the identifier for the local connections to the network. The tag is used together with the address of the virtual machine descriptor table (UTABLE) to form local socket numbers which are used in the network protocol. RESUME - used to reactivate communications with a foreign site after having previously left the TELNET command leaving the connections open.Winett [Page 1]
RFC 452 TELNET Command at Host LL February 1973 EBCDIC - to communicate with EBCDIC codes. The default is network ASCII. HALFDUP - to operate under a half duplex protocol, i.e. with a locked keyboard. The EBCDIC HALFDUP the protocol assumes that the TELNET break code (circle C) will be received to indicate when the keyboard should be locked for input. In ASCII HALFDUP the keyboard will lock after a line of input and will unlock after one or more lines have been received for output. An external interrupt will also unlock a locked keyboard. The default is full duplex where the keyboard is always unlocked for input. A null line is required to temporarily lock the keyboard in order to receive output. Usage: A number of hosts on the ARPA network provide TELNET service. A Network Virtual Terminal (NVT) has been specified so that using sites can write one TELNET program which maps a local terminal into the NVT to access any serving site on the network. Once communication has been established between a using site and a serving site, keyed input is sent to the serving system and output from the serving site, when received, is typed on the local terminal. The NVT protocol requires that the keyboard be capable of entering all of the 128 ASCII codes together with a number of the TELNET control codes. To support an NVT with an IBM 2741 terminal, it is necessary to adapt a control convention for entering codes which are not associated with single keys on the keyboard. In addition, since CP/CMS processes input from a 2741 on a line at a time terminated with a newline, a means must be establish for entering a sequence of characters for transmission which is not terminated with a newline code. When TELNET is initiated the message ENTER CONTROL CHARACTER is typed. A non-blank character should then be entered which defines the character which, in combination with another character, will be used to enter codes not associated with singleWinett [Page 2]
RFC 452 TELNET Command at Host LL February 1973 keys. The control character is also used for other special control functions as described below. Codes: The NVT usually requires that characters be transmitted in an eight bit ASCII code. Since the TELNET command is written to process EBCDIC codes ASCII codes received are translated into ASCII before being sent to a serving site. Figure 2 gives the complete definition of EBCDIC indicating the EBCDIC controls and EBCDIC graphics. Figure 3 gives the codes for the ASCII controls and graphics. The complete mapping between 8-bit EBCDIC codes and 8-bit network ASCII codes is shown in Figure 4. The EBCDIC newline code (NL) is mapped into the ASCII codes for the pair of characters CR-IF. The following ASCII/EBCDIC mapping is used for the non-EBCDIC graphics: ASCII EBCDIC TILDE (7E) = (A1) NOT BAR (7C) = (6A) OR BACK SLASH (5C) = (EO) CARAT (5E) = (71) GRAVE (6O) = (79) LEFT BRACE (7B) = (8B) RIGHT BRACE (7D) = (9B) LEFT BRACKET (5B) = (AD) RIGHT BRACKET (5D) = (BD) The ASCII control DC3 (X' 13') maps to the EBCDIC control TM (X'13'). The ASCII control NUL (X' oo') is sent to the terminal as the EBCDIC code for NULL (X' oo') and is not mapped into an IDLE (X'17'). The TELNET control hide-your-input is mapped into the EBCDIC code for bypass (print suppress) and the TELNET control noecho is mapped into the EBCDIC code for restore (print restore). If the TELNET control for echo is received, a message is printed and it is mapped into an IDLE. Similarly, if the TELNET control for break is received, a message is printed and it is mapped into an IDLE unless operation is in EBCDIC HALFDUP mode in which case the break is used to indicate that any received characters should be printed and the keyboard unlocked for input. If a data mark or an interrupt is received, no action is taken except to print a message to notify the user of this occurrence.Winett [Page 3]
RFC 452 TELNET Command at Host LL February 1973 Input: When the control character is entered, the following character is mapped into a different code than that which it is normally mapped into, except when the following character is a space or a character not defined to have a meaning when preceded by the control character. Figure 5 gives the mapping of the characters on a 2741 keyboard when preceded by a control character. The following 2741 keyboard characters do not have a different meaning when preceded by the control character. $ # * % & + - = _ . , : ; ! | ? (cent sign) SPACE BACKSPACE TAB When a character is mapped into its control code, the control character is mapped into the code for IDLE. If the control character is entered as the last character before the newline key is entered, the sequence of characters entered is transmitted without the newline code. That is, the newline code is not transmitted when it is preceded by the control character. When the 2741 keyboard is unlocked for input, characters received cannot be typed until the keyboard is locked again. After a line is entered, received characters can then be typed. When operating in full duplex or ASCII half duplex, a null line entered will allow received characters to be typed but will not cause the new line code to be transmitted. To cause a null line, i.e., just the new line code to be transmitted, the control character should be entered as the only character in the input line. In EBCDIC HALFDUP a null line entered will cause a null line to be transmitted. Output: ASCII output received from the NVT is converted into EBCDIC with the sequences CR-LF converted into IDLE-NL. The EBCDIC characters are then sent to the terminal. Note that not all 128 ASCII codes when converted to EBCDIC will print on a 2741. Of the 95 ASCII graphics and the 8 ASCII controls which are defined for the NVT printer, the following are not visible or audible:Winett [Page 4]
RFC 452 TELNET Command at Host LL February 1973 CARAT GRAVE BACK SLASH LEFT BRACE RIGHT BRACE LEFT BRACKET RIGHT BRACKET ASCII CONTROL BELL (BEL) ASCII CONTROL VERTICAL TAB (HT) ASCII CONTROL FORM FEED (FF) ASCII CONTROL CARRIAGE RETURN (CR) Figure 6 shows how the EBCDIC codes from X' 40' through X' FF' will appear on a 2741 terminal. Figure 7 shows how the EBCDIC codes will appear when printed with a PN train on the offline printer and Figure 8 shows how these codes appear when printed with a TN train. Controls: If the first character in an input line is the control character and the next character is a space, the rest of the line is interpreted as a TELNET control command. A control command consists of a control word and parameters separated by spaces. Controls are defined which permit TELNET controls to be transmitted to the serving site, allow input to come from a file or output to go to a file, allow CMS functions or transient commands to be issued, redefine the control character or TELNET mode, close connections or leave the TELNET command with connections still open, as well as controls to support a reader, punch, and printer with RJS operation. The controls are described below. CONTROL x Where x is the new control character CLOSE To close all connections and quit QUIT To leave TELNET EBCDIC To go into transparent mode, i.e., no translationWinett [Page 5]
RFC 452 TELNET Command at Host LL February 1973 ASCII To translate input and output to network ASCII Break To send the TELNET break code SYNC To send the TELNET data mark code and an interrupt AATN To send a TELNET break and a SYNC HIDE-YOUR-INPUT To send the TELNET hide you input code NOECHO To send the TELNET noecho code ECHO To send the TELNET echo code CMS command arg1...argN To issue CMS core resident function or transient command. INPUT fn ft * TERMIN * * To get input from a file If fn is defaulted, input is reset to come from the terminal. If fn is * file input resumes after the last line read. After an EOF, the next line read will be the first line of the file. An external interrupt while input is coming from a file will cause the line number of the next line to be read from the file to be typed and input to be reset to come from the terminal.Winett [Page 6]
RFC 452 TELNET Command at Host LL February 1973 OUTPUT fn OFF TERM INPUT INOUT * ON NOTERM NOINPUT OUTPUT To write output to the file "fn TERMOUT". If fn is defaulted, output is reset to go to the terminal. If fn is *, file OUTPUT is resumed with the same options as were last used. For Output to the Terminal: If the last character is a CR, a line with just the control character is typed on the next line (with a NL) If the last character is not a NL or a CR, the line is typed without a NL (i.e., with TYPE). For Output to a File: If just a NL is in the line, just the control character is sent to the file. If the last CHAR is not NL or CR, the control character is added after the last character, except if 130 characters must be sent to the file. If the last CHAR is a CR, it is included in the file. OFF causes all output to be discarded. ON is the default, and causes output to the terminal. TERM causes output to also go to the terminal. NOTERM is the default, and causes output to go the file but not to the terminal. OUTPUT is the default and causes just terminal output to be put to the file "FN termout". INPUT causes both terminal input but not output to be put to the output file. NOINPUT is defaulted and causes input to not go to the file. PURGE To purge all output currently received by the NCP. *****NOT YET IMPLEMENTED*****Winett [Page 7]
RFC 452 TELNET Command at Host LL February 1973 READER fn ft * READER To send a job to the RJS system at UCLA's CCN. If fn and ft are defaulted, input will come from the card reader. PRINTER fn ft * PRINTER To receive printer output from the RJS system at UCLA's CCN. To receive punch output from the RJS system at UCLA's CCN. If fn and ft are defaulted, output goes to the printer. PUNCH fn ft * PUNCH If fn and ft are defaulted, output goes to the punch. HOST SITE MACHINE SYSTEM HOST NUMBER DEC OCT HEX NMC UCLA SIGNA-7 SEX 1 1 01 ARC SRI PDP-10 NIC 2 2 02 UCSB UCSB 360/75 OS/MVT 3 3 03 UTAH UTAH PDP-10 TENEX 4 4 04 MULTICS MIT H-645 MULTICS 6 6 06 SDC SDC 370/155 ADEPT 8 10 08 HARV HARVARD PDP-10 4S72 9 11 09 LL LL 360/67 CP/CMS 10 12 0A CASE CASE PDP-10 10/50 13 15 0D CMU CMU PDP-10 TOPS-10 14 16 0E ILLIAC AMES 360/67 TTS/360 16 18 10 AMES AMES B-6500 ? 15 17 0F CCN UCLA 360/91 OS/MVT 65 101 41 SRI SRI-AI PDP-10 TENEX 66 102 42 BBNA BBN PDP-10 TENEX 69 105 45 DMCG MIT PDP-10 ITS 70 106 46 RAND RAND-RCC PDP-10 TENEX 71 107 47 TX2 LL TX-2 APEX 74 112 4A BBNB BBN PDP-10 TENEX 133 205 85 MIATI MIT PDP-10 ITS 134 206 86 Serving Hosts on the APRA Network Figure 1Winett [Page 8]
RFC 452 TELNET Command at Host LL February 1973 [[See Figure 2 in PDF file.]] Extended Binary-Coded Decimal Interchange Code (EBCDIC) FIGURE 2 and [[See Figure 3 in PDF file.]] USA Standard Code for Information Interchange (USASCII) FIGURE 3 ASCII ASCII ASCII SYMBOLS EBCDIC EBCDIC DEC OCT HEX HEX DEC 0 0 (00) NUL (00) 00 1 1 (01) SOH (01) 01 2 2 (02) STX (02) 02 3 3 (03) ETX (03) 03 4 4 (04) EOT (37) 55 5 5 (05) ENQ (2D) 45 6 6 (06) ACK (2E) 46 7 7 (07) BEL (2F) 47 8 10 (08) BS (16) 22 9 11 (09) HT (05) 05 10 12 (0A) LF (25) 37 11 13 (0B) VT (0B) 11 12 14 (0C) FF (0C) 12 13 15 (0D) CR (0D) 13 14 16 (0E) SO (0E) 14 15 17 (0F) SI (0F) 15 16 20 (10) DLE (10) 16 17 21 (11) DC1 (11) 17 18 22 (12) DC2 (12) 18 19 23 (13) DC3 (13) 19 20 24 (14) DC4 (3C) 60 21 25 (15) NAK (3D) 61 22 26 (16) SYN (32) 50 23 27 (17) ETB (26) 38 24 30 (18) CAN (18) 24 25 31 (19) EM (19) 25 26 32 (1A) SUB (3F) 63 27 33 (1B) CTL (27) 39 28 34 (1C) FS (1C) 28 29 35 (1D) GS (1D) 29 30 36 (1E) RS (1E) 30 31 37 (1F) US (1F) 31 32 40 (20) SP (40) 64 33 41 (21) ! (5A) 90Winett [Page 9]
RFC 452 TELNET Command at Host LL February 1973 34 42 (22) " (7F) 127 35 43 (23) # (7B) 123 36 44 (24) $ (5B) 91 37 45 (25) % (6C) 108 38 46 (26) & (50) 80 39 47 (27) ' (7D) 124 40 50 (28) ( (4D) 77 41 51 (29) ) (5D) 93 42 52 (2A) * (5C) 92 43 53 (2B) + (4E) 78 44 54 (2C) , (6D) 109 45 55 (2D) - (60) 96 46 56 (2E) . (4B) 75 47 57 (2F) / (61) 97 48 60 (30) 0 (F0) 240 49 61 (31) 1 (F1) 241 50 62 (32) 2 (F2) 242 51 63 (33) 3 (F3) 243 52 64 (34) 4 (F4) 244 53 65 (35) 5 (F5) 245 54 66 (36) 6 (F6) 246 55 67 (37) 7 (F7) 247 56 70 (38) 8 (F8) 248 57 71 (39) 9 (F9) 249 58 72 (3A) : (7A) 122 59 73 (3B) ; (5E) 94 60 74 (3C) < (4C) 76 61 75 (3D) = (7E) 126 62 76 (3E) > (6E) 110 63 77 (3F) ? (6F) 111 64 100 (40) @ (7C) 124 65 101 (41) A (C1) 193 66 102 (42) B (C2) 194 67 103 (43) C (C3) 195 68 104 (44) D (C4) 196 69 105 (45) E (C5) 197 70 106 (46) F (C6) 198 71 107 (47) G (C7) 199 72 110 (48) H (C8) 200 73 111 (49) I (C9) 201 74 112 (4A) J (D1) 209 75 113 (4B) K (D2) 210 76 114 (4C) L (D3) 211 77 115 (4D) M (D4) 212 78 116 (4E) N (D5) 213 79 117 (4F) O (D6) 214 80 120 (50) P (D7) 215 81 121 (51) Q (D8) 216Winett [Page 10]
RFC 452 TELNET Command at Host LL February 1973 82 122 (52) R (D9) 217 83 123 (53) S (E2) 226 84 124 (54) T (E3) 227 85 125 (55) U (E4) 228 86 126 (56) V (E5) 229 87 127 (57) W (E6) 230 88 130 (58) 8 (E7) 231 89 131 (59) Y (E8) 232 90 132 (5A) Z (E9) 233 91 133 (5B) [ (AD) 173 92 134 (5C) (cent sign) (4A) 74 (BACK-SLASH) 93 135 (5D) ] (BD) 189 94 136 (5E) (71) 113 (CARAT) 95 137 (5F) _ (6D) 109 96 140 (60) (79) 121 (GRAVE) 97 141 (61) a (81) 129 98 142 (62) b (82) 130 99 143 (63) c (83) 131 100 144 (64) d (84) 132 101 145 (65) e (85) 133 102 146 (66) f (86) 134 103 147 (67) g (87) 135 104 150 (68) h (88) 136 105 151 (69) i (89) 137 106 152 (6A) j (91) 145 107 153 (6B) k (92) 146 108 154 (6C) l (93) 147 109 155 (6D) m (94) 148 110 156 (6E) n (95) 149 111 157 (6F) o (96) 150 112 160 (70) p (97) 151 113 161 (71) q (98) 152 114 162 (72) r (99) 153 115 163 (73) s (A2) 162 116 164 (74) t (A3) 163 117 165 (75) u (A4) 164 118 166 (76) v (A5) 165 119 167 (77) w (A6) 166 120 170 (78) x (A7) 167 121 171 (79) y (A8) 168 122 172 (7A) z (A9) 169 123 173 (7B) { (8B) 139 124 174 (7C) | (4F) 79 (BAR/OR) 125 175 (7D) } (9B) 155 126 176 (7E) (broken bar) (5F) 95 (TILDE/NOT) 127 177 (7F) DEL (07) 7Winett [Page 11]
RFC 452 TELNET Command at Host LL February 1973 ASCII ASCII ASCII TELNET EBCDIC EBCDIC DEC OCT HEX CONTROLS HEX DEC 128 100 (80) DATA-MARK (80) 128 129 101 (81) BREAK (38) 56 130 102 (82) NOP (17) 23 IDLE 131 103 (83) NOECHO (14) 20 RESTORE 132 104 (84) ECHO (23) 35 133 105 (85) HIDE-YOUR INPUT (24) 36 BYPASS ASCII/EBCDIC Code Mappings FIGURE 4 EBCDIC EBCDIC ASCII CENT (4A) = ESC (27) (1B) CTL < (4C) = LEFT BRACKET (AD) (5B) CTL > (6E) = RIGHT BRACKET (BD) (5D) CTL ( (4D) = LEFT BRACE (8B) (7B) CTL ) (5D) = RIGHT BRACE (9B) (7D) CTL / (61) = BACK SLASH (4A) (5C) CTL " (7F) = CARAT (71) (5E) CTL ' (7D) = GRAVE (79) (60) CTL 6 (F6) = FS (1C) (1C) CTL 7 (F7) = GS (1D) (1D) CTL 8 (F8) = RS (1E) (1E) CTL 9 (F9) = US (1F) (1F) CTL _ (6D) = US (1F) (1F) CTL (broken bar) (5F) = DEL (07) (7F) CTL @ (7C) = NUL (00) (00) CTL A (C1) = SOH (01) (01) CTL B (C2) = STX (02) (02) CTL C (C3) = ETX (03) (03) CTL D (C4) = EOT (37) (04) CTL E (C5) = ENQ (2D) (05) CTL F (C6) = ACK (2E) (06) CTL G (C7) = BEL (2F) (07) CTL H (C8) = BS (16) (08) CTL I (C9) = HT (05) (09) CTL J (D1) = LF (25) (0A) CTL K (D2) = VT (0B) (0B) CTL L (D3) = FF (0C) (0C) CTL M (D4) = CR (0D) (0D)Winett [Page 12]
RFC 452 TELNET Command at Host LL February 1973 CTL N (D5) = SO (0E) (0E) CTL O (D6) = SI (0F) (0F) CTL P (D7) = DLE (10) (10) CTL Q (D8) = DC1 (11) (11) CTL R (D9) = DC2 (12) (12) CTL S (E2) = DC3 (13) (13) CTL T (E3) = DC4 (3C) (14) CTL U (E4) = NAK (3D) (15) CTL V (E5) = SYN (32) (16) CTL W (E6) = ETB (26) (17) CTL X (E7) = CAN (18) (18) CTL Y (E8) = EM (19) (19) CTL Z (E9) = SUB (3F) (1A) EBCDIC EBCDIC ASCII CTL 1 (F1) = BREAK (38) (81) - CIRCLE C CTL 2 (F2) = NOP (17) (82) - IDLE CTL 3 (F3) = NO ECHO (14) (83) - RESTORE CTL 4 (F4) = ECHO (23) (84) CTL 5 (F5) = HIDE YOU INPUT (24) (85) - BYPASS DATA MARK (80) CANNOT BE ENTERED FROM THE KEYBOARD THE FOLLOWING 2741 KEYBOARD CHARACTERS DO NOT HAVE A MEANING AS A CONTROL: $ # * % & + - = _ . , : ! | ? (cent sign) SPACE BACKSPACE TAB Keyboard Control Character Mappings FIGURE 5 (CONTINUED)Winett [Page 13]
RFC 452 TELNET Command at Host LL February 1973 [[See Figure in PDF file.]] Hex Code X'xy' for Characters on a 2741 Terminal [[See Figure in PDF file.]] Decimal Code D 'xxy" for Characters on a 2741 terminal HT X'05' = D'005' Horizontal Tab LC X'06' = D'006' Lower Case RES X'14' = D'020' Print Restore NL X'15' = D'021' New Line BS X'16' = D'022' Back Space IL X'17' = D'023' Idle BYP X'24' = D'036' Print Bypass LF X'25' = D'037' Line Feed UC X'36' = D'054' Upper Case Hex Code X'xy' and Decimal Code D'xxy' for 2741 Control Codes [[See Figure in PDF file.]] Hex Code X'xy' for Characters on the PN train [[See Figure in PDF file.]] Decimal Code D'xxy' for characters on the PN train [[See Figure in PDF file.]] Hex Code X'xy' for Characters on th TN train [[See Figure in PDF file.]] Decimal Code D'xxy' for Characters on the TN train [This RFC was put into machine readable form for entry] [into the online RFC archives by Helene Morin, Via Genie,12/1999]Winett [Page 14]
[8]ページ先頭