Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]
PROPOSED STANDARD
Network Working Group K. WhiteRequest for Comments: 2562 IBM Corp.Category: Standards Track R. Moore IBM Corp. April 1999Definitions of Protocol and Managed Objects forTN3270E Response Time Collection Using SMIv2(TN3270E-RT-MIB)Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.Copyright Notice Copyright (C) The Internet Society (1999). All Rights Reserved.Abstract This memo defines the protocol and the Management Information Base (MIB) for performing response time data collection on TN3270 and TN3270E sessions by a TN3270E server. The response time data collected by a TN3270E server is structured to support both validation of service level agreements and performance monitoring of TN3270 and TN3270E Sessions. This MIB has as a prerequisite the TN3270E-MIB, reference [20]. TN3270E, defined byRFC 2355 [19], refers to the enhancements made to the Telnet 3270 (TN3270) terminal emulation practices. Refer toRFC1041 [18], STD 8,RFC 854 [16], and STD 31,RFC 860 [17] for a sample of what is meant by TN3270 practices.Table of Contents1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . .22.0 The SNMP Network Management Framework . . . . . . . . . .23.0 Response Time Collection Methodology . . . . . . . . . . .33.1 General Response Time Collection . . . . . . . . . . . . .33.2 TN3270E Server Response Time Collection . . . . . . . . .53.3 Correlating TN3270E Server and Host Response Times . . . .103.4 Timestamp Calculation . . . . . . . . . . . . . . . . . .113.4.1 DR Usage . . . . . . . . . . . . . . . . . . . . . . .12White & Moore Standards Track [Page 1]
RFC 2562 TN3270E-RT-MIB April 19993.4.2 TIMING-MARK Usage . . . . . . . . . . . . . . . . . .133.5 Performance Data Modelling . . . . . . . . . . . . . . . .153.5.1 Averaging Response Times . . . . . . . . . . . . . . .153.5.2 Response Time Buckets . . . . . . . . . . . . . . . .184.0 Structure of the MIB . . . . . . . . . . . . . . . . . . .194.1 tn3270eRtCollCtlTable . . . . . . . . . . . . . . . . . .194.2 tn3270eRtDataTable . . . . . . . . . . . . . . . . . . . .234.3 Notifications . . . . . . . . . . . . . . . . . . . . . .244.4 Advisory Spin Lock Usage . . . . . . . . . . . . . . . . .265.0 Definitions . . . . . . . . . . . . . . . . . . . . . . .266.0 Security Considerations . . . . . . . . . . . . . . . . .457.0 Intellectual Property . . . . . . . . . . . . . . . . . .458.0 Acknowledgments . . . . . . . . . . . . . . . . . . . . .469.0 References . . . . . . . . . . . . . . . . . . . . . . . .4610.0 Authors' Addresses . . . . . . . . . . . . . . . . . . .4811.0 Full Copyright Statement . . . . . . . . . . . . . . . .491.0 Introduction This document is a product of the TN3270E Working Group. It defines a protocol and a MIB module to enable a TN3270E server to collect and keep track of response time data for both TN3270 and TN3270E clients. Basis for implementing this MIB: o TN3270E-MIB, Base Definitions of Managed Objects for TN3270E Using SMIv2 [20] o TN3270E RFCs o Telnet Timing Mark Option RFC [17]. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described inRFC 2119, reference [23].2.0 The SNMP Network Management Framework The SNMP Management Framework presently consists of five major components: o An overall architecture, described inRFC 2271 [1]. o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in STD 16,RFC 1155 [2], STD 16,RFC 1212 [3] andRFC 1215 [4]. The second version, called SMIv2, is described inRFC 1902 [5], RFCWhite & Moore Standards Track [Page 2]
RFC 2562 TN3270E-RT-MIB April 1999 1903 [6] andRFC 1904 [7]. o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in STD 15,RFC 1157 [8]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described inRFC 1901 [9] andRFC1906 [10]. The third version of the message protocol is called SNMPv3 and described inRFC 1906 [10],RFC 2272 [11] andRFC 2274 [12]. o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in STD 15,RFC 1157 [8]. A second set of protocol operations and associated PDU formats is described inRFC 1905 [13]. o A set of fundamental applications described inRFC 2273 [14] and the view-based access control mechanism described inRFC 2275 [15]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI. This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB.3.0 Response Time Collection Methodology This section explains the methodology and approach used by the MIB defined by this memo for response time data collection by a TN3270E server.3.1 General Response Time Collection Two primary methods exist for measuring response times in SNA networks: o The Systems Network Architecture Management Services (SNA/MS) Response Time Monitoring (RTM) function.White & Moore Standards Track [Page 3]
RFC 2562 TN3270E-RT-MIB April 1999 o Timestamping using definite response flows. This memo defines an approach using definite responses to timestamp the flows between a client and its TN3270E server, rather than by use of the RTM method. Extensions to the SNA/MS RTM flow were considered, but this approach was deemed unsuitable since not all TN3270E server implementations have access to their underlying SNA stacks. The RTM concepts of keeping response time buckets for service level agreements and of interval-based response time collection for performance monitoring are preserved in the MIB module defined in this memo. As mentioned, this memo focuses on using definite responses to timestamp the flows between a client and its TN3270E server for generating performance data. Use of a definite response flow requires that the client supports TN3270E with the RESPONSES function negotiated. The TN3270 TIMING-MARK option can be used instead of definite response for supporting TN3270 clients or TN3270E clients that don't support RESPONSES. This document focuses first on defining the protocol and methods for generating performance data using definite responses, and then describes how the TIMING-MARK option can be used instead of definite response. In an SNA network, a transaction between a client Logical Unit (LU) and a target host in general looks as follows: ------------------------------------------------ | | | Client LU Target SNA Host | | | | Timestamps | | request A | | -----------------------------------------> | | reply(DR) B | | | <---------------------------------------< | | | +/-RSP C | | >---------------------------------------> | | | | DR: Definite Response requested | | +/-RSP: Definite Response | | | ------------------------------------------------ This transaction is a simple one, and is being used only to illustrate how timestamping at a target SNA host can be used to generate response times. An IBM redbook [12] provides a more detailed description of response time collection for a transaction of this type. Note that for the purpose of calculating an approximationWhite & Moore Standards Track [Page 4]
RFC 2562 TN3270E-RT-MIB April 1999 for network transit time, it doesn't matter if the response is positive or negative. Two response time values are typically calculated: o Host Transit Time: Timestamp B - Timestamp A o Network Transit Time: Timestamp C - Timestamp B Network transit time is an approximation for the amount of time that a transaction requires to flow across a network, since the response flow is being substituted for the request flow at the start of the transaction. Network transit time, timestamp C - timestamp B, is the amount of time that the definite response request and its response required. Host time, timestamp B - timestamp A, is the actual time that the host required to process the transaction. Experience has shown that using the response flow to approximate network transit times is useful, and does correlate well with actual network transit times. A client SHOULD respond to a definite response request when it completes processing the transaction. This is important since it increases the accuracy of a total response time. Clients that immediately respond to a definite response request will be attributed with lower total response times then those that actually occurred. The TN3270E-RT-MIB describes a method of collecting performance data that is not appropriate for printer (LU Type 1 or LU Type 3) sessions; thus collection of performance data for printer sessions is excluded from this MIB. This exclusion of printer sessions is not considered a problem, since these sessions are not the most important ones for response time monitoring, and since historically they were excluded from SNA/MS RTM collection. The tn3270eTcpConnResourceType object in a tn3270eTcpConnEntry (in the TN3270E-MIB) can be examined to determine if a client session is ineligible for response time data collection for this reason.3.2 TN3270E Server Response Time Collection A TN3270E server connects a Telnet client performing 3270 emulation to a target SNA host over both a client-side network (client to TN3270E server) and an SNA Network (TN3270E server to target SNA host). The client-side network is typically TCP/IP, but it need not be. For ease of exposition this document uses the term "IP network" to refer to the client-side network, since IP is by far the most common protocol for these networks. A TN3270E server can use SNA definite responses and the TN3270 Enhancement (RFC 2355 [19]) RESPONSES function to calculate response times for a transaction, by timestamping when a client requestWhite & Moore Standards Track [Page 5]
RFC 2562 TN3270E-RT-MIB April 1999 arrives at the server, when the reply arrives from the target host, and when the response acknowledging this reply arrives from the client.Section 3.4, Timestamp Calculation, provides specifics on when in the sequence of flows between a TN3270E client and its target SNA host a TN3270E server takes the required timestamps. In addition, it provides information on how a TN3270 TIMING-MARK request/response flow can be used instead of DR for approximating IP network transit times. The following figure adds a TN3270E server between the client, in this case a TN3270E client and the target SNA host: ------------------------------------------------ | | | Client TN3270E Target | | Server SNA Host | | Timestamps | | | | <---IP Network-------><---SNA Network---> | | | | request D | | ------------------------------------------> | | reply(DR) E | | | <----------------------------------------< | | | +/-RSP F | | >-------------------- - - - - - - - - - > | | | ------------------------------------------------ A TN3270E server can save timestamp D when it receives a client request, save timestamp E when the target SNA host replies, and save timestamp F when the client responds to the definite response request that flowed with the reply. It doesn't matter whether the target SNA host requested a definite response on its reply: if it didn't, the TN3270E server makes the request on its own, to enable it to produce timestamp F. In this case the TN3270E server does not forward the response to the target SNA host, as the dotted line in the figure indicates. Because it is a special case, a transaction in which a target SNA host returns an UNBIND in response to a client's request, and the TN3270E server forwards the UNBIND to the client, is not included in any response time calculations.White & Moore Standards Track [Page 6]
RFC 2562 TN3270E-RT-MIB April 1999 In order to generate timestamp F, a TN3270E server MUST insure that the transaction specifies DR, and that the TN3270E RESPONSES function has been negotiated between itself and the client. Negotiation of the TN3270E RESPONSES function occurs during the client's TN3270E session initialization. The TN3270E servers that the authors are aware of do request the RESPONSES function during client session initialization. TN3270E clients either automatically support the RESPONSES function, or can be configured during startup to support it. Using timestamps D, E, and F the following response times can be calculated by a TN3270E server: o Total Response time: Timestamp F - Timestamp D o IP Network Transit Time: Timestamp F - Timestamp E Just as in the SNA case presented above, these response times are also approximations, since the final +/- RSP from the client is being substituted for the request from the client that began the transaction. The MIB provides an object, tn3270eRtCollCtlType, to control several aspects of response time data collection. One of the available options in setting up a response time collection policy is to eliminate the IP-network component altogether. This might be done because it is determined either that the additional IP network traffic would not be desirable, or that the IP-network component of the overall response times is not significant. Excluding the IP-network component from response times also has an implication for the way in which response time data is aggregated. A TN3270E server may find that some of its clients simply don't support any of the functions necessary for the server to calculate the IP- network component of response times. For these clients, the most that the server can calculate is the SNA-network component of their overall response times; the server records this SNA-network component as the TOTAL response time each of these clients' transactions. If a response time collection is aggregating data from a number of clients, some of which have the support necessary for including the IP-network component in their total response time calculations, and some of which do not, then the server aggregates the data differently depending on whether the collection has been defined to include or exclude the IP-network component: o If the IP-network component is included, then transactions for the clients that don't support calculation of the IP-network component of their response times are excluded from the aggregation altogether.White & Moore Standards Track [Page 7]
RFC 2562 TN3270E-RT-MIB April 1999 o If the IP-network component is excluded, then total response times for ALL clients include only the SNA-network component, even though the server could have included an IP-network component in the overall response times for some of these clients. The server does this by setting timestamp F, which marks the end of a transaction's total response time, equal to timestamp E, the end of the transaction's SNA-network component. The principle here is that all the transactions contributing their response times to an aggregated value MUST make the same contribution. If the aggregation specifies that an IP-network component MUST be included in the aggregation's response times, then transactions for which an IP-network component cannot be calculated aren't included at all. If the aggregation specifies that an IP- network component is not to be included, then only the SNA-network component is used, even for those transactions for which an IP- network component could have been calculated. There is one more complication here: the MIB allows a management application to enable or disable dynamic definite responses for a response time collection. Once again the purpose of this option is to give the network operator control over the amount of traffic introduced into the IP network for response time data collection. A DYNAMIC definite response is one that the TN3270E server itself adds to a reply, in a transaction for which the SNA application at the target SNA host did not specify DR in its reply. When the +/-RSP comes back from the client, the server uses this response to calculate timestamp F, but then it does not forward the response on to the SNA application (since the application is not expecting a response to its reply). The dynamic definite responses option is related to the option of including or excluding the IP-network component of response times (discussed above) as follows: o If the IP-network component is excluded, then there is no reason for enabling dynamic definite responses: the server always sets timestamp F equal to timestamp E, so the additional IP-network traffic elicited by a dynamic definite response would serve no purpose. o If the IP-network component is included, then enabling dynamic definite responses causes MORE transactions to be included in the aggregated response time values: - For clients that do not support sending of responses, timestamp F can never be calculated, and so their transactions are never included in the aggregate.White & Moore Standards Track [Page 8]
RFC 2562 TN3270E-RT-MIB April 1999 - For clients that support sending of responses, timestamp F will always be calculated for transactions in which the host SNA application specifies DR in its reply, and so these transactions will always be included in the aggregate. - For clients that support sending of responses, having dynamic definite responses enabled for a collection results in the inclusion of additional transactions in the aggregate: specifically, those for which the host SNA application did not specify DR in its reply. A TN3270E server also has the option of substituting TIMING-MARK processing for definite responses in calculating the IP-network component of a transaction's response time. Once again, there is no reason for the server to do this if the collection has been set up to exclude the IP-network component altogether in computing response times. The MIB is structured to keep counts and averages for total response times (F - D) and their IP-network components (F - E). A management application can obviously calculate from these two values an average SNA-network component (E - D) for the response times. This SNA- network component includes the SNA node processing time at both the TN3270E server and at the target application. A host TN3270E server refers to an implementation where the TN3270E server is collocated with the Systems Network Architecture (SNA) System Services Control Point (SSCP) for the dependent Secondary Logical Units (SLUs) that the server makes available to its clients for connecting into an SNA network. A gateway TN3270E server resides on an SNA node other than an SSCP, either an SNA type 2.0 node, a boundary-function-attached type 2.1 node, or an APPN node acting in the role of a Dependent LU Requester (DLUR). Host and gateway TN3270E server implementations typically differ greatly as to their internal implementation and System Definition (SYSDEF) requirements. If a host TN3270E server is in the same SNA host as the target application, then the SNA-network component of a transaction's response time will approximately equal the host transit time (B - A) described previously. A host TN3270E server implementation can, however, typically support the establishment of sessions to target applications in SNA hosts remote from itself. In this case the SNA- network component of the response time equals the actual SNA-network transit time plus two host transit times.White & Moore Standards Track [Page 9]
RFC 2562 TN3270E-RT-MIB April 19993.3 Correlating TN3270E Server and Host Response Times It is possible that response time data is collected from TN3270E servers at the same time as a management application is monitoring the SNA sessions at a host. For example, a management application can be monitoring a secondary logical unit (SLU) while retrieving data from a TN3270E server. Consider the following figure: ------------------------------------------------ | | | Client TN3270E Target | | Server SNA Host | | Timestamps (PLU) | | (SLU) Timestamps| | <---IP Network-------><---SNA Network---> | | | | request D A | | ------------------------------------------> | | reply(DR) E B | | | <----------------------------------------< | | | +/-RSP F C | | >--------------------------------------> | | | ------------------------------------------------ The following response times are available: o Target SNA host transit time: Timestamp B - Timestamp A o Target SNA host network transit time: Timestamp C - Timestamp B o TN3270E server total response time: Timestamp F - Timestamp D o TN3270E server IP-network component: Timestamp F - Timestamp E The value added by the TN3270E server in this situation is its approximation of the IP-network component of the overall response time. The IP-network component can be subtracted from the total network transit time (which can be captured at an SSCP monitoring SNA traffic from/to the SLU) to see the actual SNA versus IP network transit times. The MIB defined by this memo does not specifically address correlation of the data it contains with response time data collected by direct monitoring of SNA resources: its focus is exclusively response time data collection from a TN3270E server perspective. It has, however, in conjunction with the TN3270E-MIB [10], been structured to provide the information necessary for correlation between TN3270E server-provided response time information and that gathered from directly monitoring SNA resources.White & Moore Standards Track [Page 10]
RFC 2562 TN3270E-RT-MIB April 1999 A management application attempting to correlate SNA resource usage to Telnet clients can monitor either the tn3270eResMapTable or the tn3270eTcpConnTable to determine resource-to-client address mappings. Both of these tables are defined by the TN3270E-MIB [10]. Another helpful table is the tn3270eSnaMapTable, which provides a mapping between SLU names as they are known at the SSCP (VTAM) and their local names at the TN3270E server. Neither the tn3270eClientGroupTable, the tn3270eResPoolTable, nor the tn3270eClientResMapTable from the TN3270E-MIB can be used for correlation, since the mappings defined by these tables can overlap, and may not provide one-to-one mappings.3.4 Timestamp Calculation This section goes into more detail concerning when the various timestamps can be taken as the flows between a TN3270E client and its target SNA host pass through a TN3270E server. In addition, information is provided on how the TN3270 TIMING-MARK request/response flow can be used in place of DR for approximating IP network transit times.White & Moore Standards Track [Page 11]
RFC 2562 TN3270E-RT-MIB April 19993.4.1 DR Usage Consider the following flow: ---------------------------------------------------------- | | | Client TN3270E Target SNA | | Server Host | | Timestamps | | | | <---IP Network-------><---SNA Network---> | | | | request D (BB,CD,OIC,ER) | | -------------------------------------------> | | reply(DR) (FIC,ER,EB) | | | <-----------------------------------------< | | reply (MIC,ER) | | <-----------------------------------------< | | reply (MIC,ER) | | <-----------------------------------------< | | reply E (LIC,DR) | | <-----------------------------------------< | | | +/-RSP F | | >----------------------------------------> | | | | BB : Begin Bracket ER : Response by exception | | EB : End Bracket DR : Definite Response Requested | | CD : Change Direction FIC : First in chain | | OIC: Only in chain MIC: Middle in chain | | LIC: Last in chain | ---------------------------------------------------------- Timestamp D is taken at the TN3270E server when the server has received data from a client for forwarding to its target SNA host, and the direction of the SNA session allows the server to forward the data immediately (either the direction is inbound towards the SNA host, or the session is between brackets). This is most likely when the server finds the end of record indicator in the TCP data received from the client. The target SNA application returns its reply in one or more SNA Request Units (RUs); in this example there are four RUs in the reply. The first RU is marked as first in chain (FIC), the next two are marked as middle in chain (MIC), and the last is marked as last in chain (LIC). If the SNA host sends a multiple-RU chain, the server does not know until the last RU is received whether DR is being requested. The server's only chance to request DR from the client, however, comes when it forwards the FIC RU, since this is the onlyWhite & Moore Standards Track [Page 12]
RFC 2562 TN3270E-RT-MIB April 1999 time that the TN3270E header is included. Since a server may forward the FIC RU to the client before it receives the LIC RU from the SNA host, some servers routinely specify DR on all FIC RUs. If the server has specified DR on the TN3270E request for the FIC RU in a chain, it takes timestamp E when it forwards the LIC RU to the client. Since timestamp E is used for calculating the IP-network time for the transaction, the server SHOULD take timestamp E as close as possible to its "Telnet edge". The server takes timestamp F when it receives the RESPONSES response from the client. A target SNA application doesn't necessarily return data to a client in a transaction; it may, for example, require more data from the client before it can formulate a reply. In this case the application may simply return to the TN3270E server a change of direction indicator. At this point the server must send something to the client (typically a Write operation with a WCC) to unlock the keyboard. If the server specifies DR on the request to the client triggered by its receipt of the change of direction indicator from the SNA application, then timestamps E and F can be taken, and the usual response times can be calculated. When the client sends in the additional data and gets a textual response from the SNA application, the server treats this as a separate transaction from the one involving the change of direction.3.4.2 TIMING-MARK Usage It is possible for a TN3270E server to use the TIMING-MARK flow for approximating IP network transit times. Using TIMING-MARKs would make it possible for a server to collect performance data for TN3270 clients, as well as for TN3270E clients that do not support the RESPONSES function. In order for TIMING-MARKs to be used in this way, a client can't have the NOP option enabled, since responses are needed to the server's TIMING-MARK requests. An IP network transit time approximation using a TIMING-MARK is basically the amount of time it takes for a TN3270 server to receive from a client a response to a TIMING-MARK request. To get an estimate for IP network transit time, a TN3270E server sends a TIMING-MARK request to a client after a LIC RU has been received, as a means of approximating IP network transit time:White & Moore Standards Track [Page 13]
RFC 2562 TN3270E-RT-MIB April 1999 --------------------------------------------------- | | | Client TN3270E Target | | Server Host | | Timestamps | | | | <---IP Network-------><---SNA Network---> | | | | request D (BB,CD,OIC,ER) | | -------------------------------------------> | | reply (FIC,ER,EB) | | | <-----------------------------------------< | | reply (MIC,ER) | | <-----------------------------------------< | | reply (MIC,ER) | | <-----------------------------------------< | | reply E (LIC,ER) | | <-----------------------------------------< | | TIMING-MARK Rqst E' | | <--------------------- | | | TIMING-MARK Rsp F' | | >-------------------> | | | --------------------------------------------------- The response times can then be calculated as follows: o TN3270E server total response time: (Timestamp E - Timestamp D) + (Timestamp F' - Timestamp E') o TN3270E server IP network time: Timestamp F' - Timestamp E' If a TN3270E server is performing the TIMING-MARK function (independent of the response time monitoring use of the function discussed here), then it most likely has a TIMING-MARK interval for determining when to examine client sessions for sending the TIMING- MARK request. This interval, which is ordinarily a global value for an entire TN3270E server, is represented in the TN3270E-MIB by the tn3270eSrvrConfTmNopInterval object. A TIMING-MARK request is sent only if, when it is examined, a client session is found to have had no activity for a different fixed length of time, represented in the TN3270E-MIB by the tn3270eSrvrConfTmNopInactTime object. Servers that support a large number of client sessions should spread out the TIMING-MARK requests they send to these clients over the activity interval, rather than sending them all in a single burst, since otherwise the network may be flooded with TIMING-MARK requests. When a server uses TIMING-MARKs for approximating response times,White & Moore Standards Track [Page 14]
RFC 2562 TN3270E-RT-MIB April 1999 this tends to introduce a natural spreading into its TIMING-MARK requests, since the requests are triggered by the arrival of traffic from an SNA host. A TN3270E server MUST integrate its normal TIMING-MARK processing with its use of TIMING-MARKs for computing response times. In particular, it MUST NOT send a second TIMING-MARK request to a client while waiting for the first to return, since this is ruled out by the TIMING-MARK protocol itself. If a TIMING-MARK flow has just been performed for a client shortly before the LIC RU arrives, the server MAY use the interval from this flow as its approximation for IP network transit time, (in other words, as its (F' - E') value) when calculating its approximation for the transaction's total response time, rather than sending a second TIMING-MARK request so soon after the preceding one. Regardless of when the server sends its TIMING-MARK request, the accuracy of its total response time calculation depends on exactly when the client responds to the TIMING-MARK request.3.5 Performance Data Modelling The following two subsections detail how the TN3270E-RT-MIB models and controls capture of two types of response time data: average response times and response time buckets.3.5.1 Averaging Response Times Average response times play two different roles in the MIB: o They are made available for management applications to retrieve. o They serve as triggers for emitting notifications. Sliding-window averages are used rather than straight interval-based averages, because they are often more meaningful, and because they cause less notification thrashing. Sliding-window average calculation can, if necessary, be disabled, by setting the sample period multiplier, tn3270eRtCollCtlSPMult, to 1, and setting the sample period, tn3270eRtCollCtlSPeriod, to the required collection interval. In order to calculate sliding-window averages, a TN3270E server MUST: o Select a fixed, relatively short, sample period SPeriod; the default value for SPeriod in the MIB is 20 seconds.White & Moore Standards Track [Page 15]
RFC 2562 TN3270E-RT-MIB April 1999 o Select an averaging period multiplier SPMult. The actual collection interval will then be SPMult times SPeriod. The default value for SPMult in the MIB is 30, yielding a default collection interval of 10 minutes. Note that the collection interval (SPMult*SPeriod) is always a multiple of the sample period. Clearlly, SPMult*SPeriod should not be thought of as literally the averaging period. The average calculated will include contributions older than that time, and does not weight equally all contributions since that time. In fact, it gives a smoother result than a traditional sliding average, as used in finance. More subtly, it is best to think of the effective averaging period as being 2*SPMult*SPeriod. To see this, consider how long the contribution to the result made by a particular transaction lasts. With a traditional sliding average, it lasts exactly the averaging period. With the aging mechanism described here, it has a half-life of SPMult*SPeriod. o Maintain the following counters to keep track of activity within the current sample period; these are internal counters, not made visible to a management application via the MIB. - T (number of transactions in the period) - TotalRts (sum of the total response times for all transactions in the period) - TotalIpRts (sum of the IP network transit times for all transactions in the period; note that if IP network transit times are being excluded from the response time collection, this value will always be 0). o Also maintain sliding counters, initialized to zero, for each of the quantities being counted: - AvgCountTrans (sliding count of transactions) - TotalRtsSliding (sliding count of total response times) - TotalIpRtsSliding (sliding count of IP network transit times) o At the end of each sample period, update the sliding interval counters, using the following floating-point calculations: AvgCountTrans = AvgCountTrans + T - (AvgCountTrans / SPMult) TotalRtsSliding = TotalRtsSliding + TotalRts - (TotalRtsSliding / SPMult)White & Moore Standards Track [Page 16]
RFC 2562 TN3270E-RT-MIB April 1999 TotalIpRtsSliding = TotalIpRtsSliding + TotalIpRts - (TotalIpRtsSliding / SPMult) Then reset T, TotalRts, and TotalIpRts to zero for use during the next sample period. o At the end of a collection interval, update the following MIB objects as indicated; the floating-point numbers are rounded rather than truncated. tn3270eRtDataAvgCountTrans = AvgCountTrans tn3270eRtDataAvgRt = TotalRtsSliding / AvgCountTrans tn3270eRtDataAvgIpRt = TotalIpRtsSliding / AvgCountTrans As expected, if IP network transit times are being excluded from response time collection, then tn3270eRtDataAvgIpRt will always return 0. The sliding transaction counter AvgCountTrans is not used for updating the MIB object tn3270eRtDataCountTrans: this object is an ordinary SMI Counter32, which maintains a total count of transactions since its last discontinuity event. The sliding counters are used only for calculating averages. Two mechanisms are present in the MIB to inhibit the generation of an excessive number of notifications related to average response times. First, there are high and low thresholds for average response times. A tn3270eRtExceeded notification is generated the first time a statistically significant average response time is found to have exceeded the high threshold. (The test for statistical significance is described below.) After this, no other tn3270eRtExceeded notifications are generated until an average response time is found to have fallen below the low threshold. The other mechanism to limit notifications is the significance test for a high average response time. Intuitively, the significance of an average is directly related to the number of samples that go into it; so we might be inclined to use a rule such as "for the purpose of generating tn3270eRtExceeded notifications, ignore average response times based on fewer than 20 transactions in the sample period." In the case of response times, however, the number of transactions sampled in a fixed sampling period is tied to these transactions' response times. A few transactions with long response times can guarantee that there will not be many transactions in a sample, because these transactions "use up" the sampling time. Yet this caseWhite & Moore Standards Track [Page 17]
RFC 2562 TN3270E-RT-MIB April 1999 of a few transactions with very poor response times should obviously be classified as a problem, not as a statistical anomaly based on too small a sample. The solution is to make the significance level for a sample a function of the average response time. A value IdleCount is specified, which is used to qualify an sample as statistically significant. In order to determine at a collection interval whether to generate a tn3270eRtExceeded notification, a TN3270E server uses the following algorithm: if AvgCountTrans * ((AvgRt/ThreshHigh - 1) ** 2) >= IdleCount then generate the notification, where AvgRt is the value that would be returned by the object tn3270eRtDataAvgRt at the end of the interval, and the "**" notation indicates exponientiation. Two examples illustrate how this algorithm works. Suppose that IdleCount has been set to 20 transactions, and the high threshold to 200 msecs per transaction. If the average observed response time is 300 msecs, then a notification will be generated only if AvgCountTrans >= 80. If, however, the observed response time is 500 msecs, then a notification is generated if AvgCountTrans >= 9. There is no corresponding significance test for the tn3270eRtOkay notification: this notification is generated based on an average response time that falls below the low threshold, regardless of the sample size behind that average.3.5.2 Response Time Buckets The MIB also supports collection of response time data into a set of five buckets. This data is suitable either for verification of service level agreements, or for monitoring by a management application to identify performance problems. The buckets provide counts of transactions whose total response times fall into a set of specified ranges. Like everything for a collection, the "total" response times collected in the buckets are governed by the specification of whether IP network transit times are to be included in the totals. Depending on how this option is specified, the response times being counted in the buckets will either be total response times (F - D), or only SNA network transit times (effectively E - D, because when it is excluding the IP-network component of transactions, a server makes timestamp F identical to timestamp E).White & Moore Standards Track [Page 18]
RFC 2562 TN3270E-RT-MIB April 1999 Four bucket boundaries are specified for a response time collection, resulting in five buckets. The first response time bucket counts those transactions whose total response times were less than or equal to Boundary 1, the second bucket counts those whose response times were greater than Boundary 1 but less than or equal to Boundary 2, and so on. The fifth bucket is unbounded on the top, counting all transactions whose response times were greater than Boundary 4. The four bucket boundaries have default values of: 1 second, 2 seconds, 5 seconds, and 10 seconds, respectively. These values are the defaults in the 3174 controller's implementation of the SNA/MS RTM function, and are thought to be appropriate for this MIB as well. In SNA/MS the counter buckets were (by today's standards) relatively small, with a maximum value of 65,535. The bucket objects in the MIB are all Counter32's. The following figure represents the buckets pictorially: ---------------------------------------------- | | | Response Time Boundaries | | | | | | | | | | | | | | | | | | | | | | | no | | 0 B-1 B-2 B-3 B-4 bound| | | | | | | | | | |Bucket1|Bucket2|Bucket3|Bucket4|Bucket5| | | ----------------------------------------- | | | ----------------------------------------------4.0 Structure of the MIB The TN3270E-RT-MIB has the following components: o tn3270eRtCollCtlTable o tn3270eRtDataTable o Notifications o Advisory Spin Lock Usage4.1 tn3270eRtCollCtlTable The tn3270eRtCollCtlTable is indexed by tn3270eSrvrConfIndex and tn3270eClientGroupName imported from the TN3270E-MIB. tn3270eSrvrConfIndex identifies within a host a particular TN3270EWhite & Moore Standards Track [Page 19]
RFC 2562 TN3270E-RT-MIB April 1999 server. tn3270eClientGroupName identifies a collection of IP clients for which response time data is to be collected. The set of clients is defined using the tn3270eClientGroupTable from the TN3270E-MIB. A tn3270eRtCollCtlEntry contains the following objects: -------------------------------------------------- 1st Index | tn3270eSrvrConfIndex Unsigned32 | 2nd Index | tn3270eClientGroupName Utf8String | | tn3270eRtCollCtlType BITS | | tn3270eRtCollCtlSPeriod Unsigned32 | | tn3270eRtCollCtlSPMult Unsigned32 | | tn3270eRtCollCtlThreshHigh Unsigned32 | | tn3270eRtCollCtlThreshLow Unsigned32 | | tn3270eRtCollCtlIdleCount Unsigned32 | | tn3270eRtCollCtlBucketBndry1 Unsigned32 | | tn3270eRtCollCtlBucketBndry2 Unsigned32 | | tn3270eRtCollCtlBucketBndry3 Unsigned32 | | tn3270eRtCollCtlBucketBndry4 Unsigned32 | | tn3270eRtCollCtlRowStatus RowStatus | -------------------------------------------------- The tn3270eRtCollCtlType object controls the type(s) of response time collection that occur, the granularity of the collection, whether dynamic definite responses SHOULD be initiated, and whether notifications SHOULD be generated. This object is of BITS SYNTAX, and thus allows selection of multiple options. The BITS in the tn3270eRtCollCtlType object have the following meanings: o aggregate(0) - If this bit is set to 1, then data SHOULD be aggregated for the whole client group. In this case there will be only one row created for the collection in the tn3270eRtDataTable. The first two indexes for this row, tn3270eSrvrConfIndex and tn3270eClientGroupName, will have the same values as the indexes for the corresponding tn3270eRtCollCtlEntry. The third and fourth indexes of an aggregated tn3270eRtDataEntry have the values unknown(0) (tn3270eRtDataClientAddrType) and a zero-length octet string (tn3270eRtDataClientAddress). The fifth index, tn3270eRtDataClientPort, has the value 0. If this bit is set to 0, then a separate entry is created in the tn3270eRtDataTable from each member of the client group. In this case tn3270eRtDataClientAddress contains the client's actual IPWhite & Moore Standards Track [Page 20]
RFC 2562 TN3270E-RT-MIB April 1999 Address, tn3270eRtDataClientAddrType indicates the address type, and tn3270eRtDataClientPort contains the number of the port the client is using for its TN3270/TN3270E session. o excludeIpComponent(1) - If this bit is set to 1, then the server SHOULD exclude the IP-network component from all the response times for this collection. If the target SNA application specifies DR in any of its replies, this DR will still be passed down to the client, and the client's response will still be forwarded to the application. But this response will play no role in the server's response time calculations. If this bit is set to 0, then the server includes in the collection only those transactions for which it can include an (approximate) IP-network component in the total response time for the transaction. This component MAY be derived from a "natural" DR (if the client supports the RESPONSES function), from a dynamic DR introduced by the server (if the client supports the RESPONSES function and the ddr(2) bit has been set to 1), or from TIMING-MARK processing (if the client supports TIMING-MARKs). If this bit is set to 1, then the ddr(2) bit is ignored, since there is no reason for the server to request additional responses from the client(s) in the group. o ddr(2) - If this bit is set to 1, then the server SHOULD, for those clients in the group that support the RESPONSES function, add a DR request to the FIC reply in each transaction, and use the client's subsequent response for calculating an (approximate) IP-network component to include in the transaction's total response times. If this bit is set to 0, then the server does not add a DR request that it was not otherwise going to add to any replies from the target SNA application. If the excludeIpComponent(1) bit is set to 1, then this bit is ignored by the server. o average(3) - If this bit is set to 1, then the server SHOULD calculate a sliding-window average for the collection, based on the parameters specified for the group. If this bit is set to 0, then an average is not calculated. In this case the tn3270eRtExceeded and tn3270eRtOkay notifications are not generated, even if the traps(5) bit is set to 1.White & Moore Standards Track [Page 21]
RFC 2562 TN3270E-RT-MIB April 1999 o buckets(4) - If this bit is set to 1, then the server SHOULD create and increment response time buckets for the collection, based on the parameters specified for the group. If this bit is set to 0, then response time buckets are not created. o traps(5) - If this bit is set to 1, then a TN3270E Server is enabled to generate notifications pertaining to an tn3270eCollCtlEntry. tn3270CollStart and tn3270CollEnd generation is enabled simply by traps(5) being set to 1. tn3270eRtExceeded and tn3270eRtOkay generation enablement requires that average(3) be set to 1 in addition to the traps(5) requirement. If traps(5) is set to 0, then none of the notifications defined in this MIB are generated for a particular tn3270eRtCollCtlEntry. Either the average(3) or the buckets(4) bit MUST be set to 1 in order for response time data collection to occur; both bits MAY be set to 1. If the average(3) bit is set to 1, then the following objects have meaning, and are used to control the calculation of the averages, as well as the generation of the two notifications related to them: o tn3270eRtCollCtlSPeriod o tn3270eRtCollCtlSPMult o tn3270eRtCollCtlThreshHigh o tn3270eRtCollCtlThreshLow o tn3270eRtCollCtlIdleCount The previous objects' values are meaningless if the associated average(3) bit is not set to 1. If the buckets(4) bit is set to 1, then the following objects have meaning, and specify the bucket boundaries: o tn3270eRtCollCtlBucketBndry1 o tn3270eRtCollCtlBucketBndry2 o tn3270eRtCollCtlBucketBndry3 o tn3270eRtCollCtlBucketBndry4 The previous objects' values are meaningless if the associated buckets(4) bit is not set to 1. If an entry in the tn3270RtCollCtlTable has the value active(1) for its RowStatus, then an implementation SHALL NOT allow Set operations for any objects in the entry except:White & Moore Standards Track [Page 22]
RFC 2562 TN3270E-RT-MIB April 1999 o tn3270eRtCollCtlThreshHigh o tn3270eRtCollCtlThreshLow o tn3270eRtCollCtlRowStatus4.2 tn3270eRtDataTable Either a single entry or multiple entries are created in the tn3270eRtDataTable for each tn3270eRtCollCtlEntry, depending on whether tn3270eRtCollCtlType in the control entry has aggregate(0) selected. The contents of an entry in the tn3270eRtDataTable depend on the contents of the corresponding entry in the tn3270eRtCollCtlTable: as described above, some objects in the data entry return meaningful values only when the average(3) option is selected in the control entry, while others return meaningful values only when the buckets(4) option is selected. If both options are selected, then all the objects return meaningful values. When an object is not specified to return a meaningful value, an implementation may return any syntactically valid value in response to a Get operation. The following objects return meaningful values if and only if the average(3) option was selected in the corresponding tn3270eRtCollCtlEntry: o tn3270eRtDataAvgRt o tn3270eRtDataAvgIpRt o tn3270eRtDataAvgCountTrans o tn3270eRtDataIntTimeStamp o tn3270eRtDataTotalRts o tn3270eRtDataTotalIpRts o tn3270eRtDataCountTrans o tn3270eRtDataCountDrs o tn3270eRtDataElapsRndTrpSq o tn3270eRtDataElapsIpRtSq The first three objects in this list return values derived from the sliding-window average calculations described earlier. The time of the most recent sample for these calculations is returned in the tn3270eRtDataIntTimeStamp object. The next four objects are normal Counter32 objects, maintaining counts of total response time and total transactions. The last two objects return sum of the squares values, to enable variance calculations by a management application. The following objects return meaningful values if and only if the buckets(4) option was selected in the corresponding tn3270eRtCollCtlEntry:White & Moore Standards Track [Page 23]
RFC 2562 TN3270E-RT-MIB April 1999 o tn3270eRtDataBucket1Rts o tn3270eRtDataBucket2Rts o tn3270eRtDataBucket3Rts o tn3270eRtDataBucket4Rts o tn3270eRtDataBucket5Rts A discontinuity object, tn3270eRtDataDiscontinuityTime, can be used by a management application to detect when the values of the counter objects in this table may have been reset, or otherwise experienced a discontinuity. A possible cause for such a discontinuity is the TN3270E server's being stopped or restarted. This object returns a meaningful value regardless of which collection control options were selected. An object, tn3270eRtDataRtMethod, identifies whether the IP Network Time was calculated using either the definite response or TIMING-MARK approach. When an entry is created in the tn3270eRtCollCtlTable with its tn3270eRtCollCtlType aggregate(0) bit set to 1, an entry is automatically created in the tn3270eRtDataTable; this entry's tn3270eRtDataClientAddress has the value of a zero-length octet string, its tn3270eRtDataClientAddrType has the value of unknown(0), and its tn3270eRtDataClientPort has the value 0. When an entry is created in the tn3270eRtCollCtlTable with its tn3270eRtCollCtlType aggregate(0) bit set to 0, a separate entry is created in the tn3270eRtDataTable for each member of the client group that currently has a session with the TN3270E server. Entries are subsequently created for clients that the TN3270E server determines to be members of the client group when these clients establish sessions with the server. Entries are also created when clients with existing sessions are added to the group. All entries associated with a tn3270eRtCollCtlEntry are deleted from the tn3270eRtDataTable when that entry is deleted from the tn3270eRtCollCtlTable. An entry for an individual client in a client group is deleted when its TCP connection terminates. Once it has been created, a client's entry in the tn3270eRtDataTable remains active as long as the collection's tn3270eRtCollCtlEntry exists, even if the client is removed from the client group for the tn3270eRtCollCtlEntry.4.3 Notifications This MIB defines four notifications related to a tn3270eRtDataEntry. If the associated tn3270eRtCollCtlType object's traps(5) bit is set to 1, then the tn3270RtCollStart and tn3270RtCollEnd notificationsWhite & Moore Standards Track [Page 24]
RFC 2562 TN3270E-RT-MIB April 1999 are generated when, respsectively, the tn3270eRtDataEntry is created and deleted. If, in addition, this tn3270eRtCollCtlType object's average(3) bit is set to 1, then the the tn3270eRtExceeded and tn3270eRtOkay notifications are generated when the conditions they report occur. The following notifications are defined by this MIB: o tn3270eRtExceeded - The purpose of this notification is to signal that a performance problem has been detected. If average(3) response time data is being collected, then this notification is generated whenever (1) an average response time is first found, on a collection interval boundary, to have exceeded the high threshold tn3270eRtCollCtlThreshHigh specified for the client group, AND (2) the sample on which the average is based is determined to have been a significant one, via the significance algorithm described earlier. This notification is not generated again for a tn3270eRtDataEntry until an average response time falling below the low threshold tn3270eRtCollCtlThreshLow specified for the client group has occurred for the entry. o tn3270eRtOkay - The purpose of this notification is to signal that a previously reported performance problem has been resolved. If average(3) response time data is being collected, then this notification is generated whenever (1) a tn3270eRtExceeded notification has already been generated, AND (2) an average response time is first found, on a collection interval boundary, to have fallen below the low threshold tn3270eRtCollCtlThreshLow specified for the client group. This notification is not generated again for a tn3270eRtDataEntry until an average response time exceeding the high threshold tn3270eRtCollCtlThreshHigh specified for the client group has occurred for the entry. Taken together, the two preceding notifications serve to minimize the generation of an excessive number of traps in the case of an average response time that oscillates about its high threshold. o tn3270eRtCollStart - This notification is generated whenever data collection begins for a client group, or when a new tn3270eRtDataEntry becomes active. The primary purpose of this notification is signal to a management application that a new client TCP session has been established, and to provide the IP- to-resource mapping for the session. This notification is not critical when average(3) data collection is not being performed for the client group.White & Moore Standards Track [Page 25]
RFC 2562 TN3270E-RT-MIB April 1999 o tn3270eRtCollEnd - This notification is generated whenever a data collection ends. For an aggregate collection, this occurs when the corresponding tn3270eRtCollCtlEntry is deleted. For an individual collection, this occurs either when the tn3270eRtCollCtlEntry is deleted, or when the client's TCP connection terminates. The purpose of this notification is to enable a management application to complete a monitoring function that it was performing, by returning final values for the collection's data objects.4.4 Advisory Spin Lock Usage Within the TN3270E-RT-MIB, tn3270eRtSpinLock is defined as an advisory lock that allows cooperating TN3270E-RT-MIB applications to coordinate their use of the tn3270eRtCollCtlTable. When creating a new entry or altering an existing entry in the tn3270eRtCollCtlTable, an application SHOULD make use of tn3270eRtSpinLock to serialize application changes or additions. Since this is an advisory lock, its use by management applications SHALL NOT be enforced by agents. Agents MUST, however, implement the tn3270eRtSpinLock object.5.0 Definitions TN3270E-RT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Unsigned32, Gauge32 FROM SNMPv2-SMI RowStatus, DateAndTime, TimeStamp, TestAndIncr FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF tn3270eSrvrConfIndex, tn3270eClientGroupName, tn3270eResMapElementType FROM TN3270E-MIB IANATn3270eAddrType, IANATn3270eAddress FROM IANATn3270eTC-MIB snanauMIB FROM SNA-NAU-MIB; tn3270eRtMIB MODULE-IDENTITY LAST-UPDATED "9807270000Z" -- July 27, 1998 ORGANIZATION "TN3270E Working Group" CONTACT-INFO "Kenneth White (kennethw@vnet.ibm.com) IBM Corp. - Dept. BRQA/Bldg. 501/G114 P.O. Box 12195White & Moore Standards Track [Page 26]
RFC 2562 TN3270E-RT-MIB April 1999 3039 Cornwallis RTP, NC 27709-2195 Robert Moore (remoore@us.ibm.com) IBM Corp. - Dept. BRQA/Bldg. 501/G114 P.O. Box 12195 3039 Cornwallis RTP, NC 27709-2195 (919) 254-4436" DESCRIPTION "This module defines a portion of the management information base (MIB) that enables monitoring of TN3270 and TN3270E clients' response times by a TN3270E server." REVISION "9807270000Z" -- July 27, 1998 DESCRIPTION "RFC nnnn (Proposed Standard)" -- RFC Editor to fill in ::= { snanauMIB 9 } -- snanauMIB ::= { mib-2 34 } -- Top level structure of the MIB tn3270eRtNotifications OBJECT IDENTIFIER ::= { tn3270eRtMIB 0 } tn3270eRtObjects OBJECT IDENTIFIER ::= { tn3270eRtMIB 1 } tn3270eRtConformance OBJECT IDENTIFIER ::= { tn3270eRtMIB 3 } -- MIB Objects -- Response Time Control Table tn3270eRtCollCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF Tn3270eRtCollCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The response time monitoring collection control table, which allows a management application to control the types of response time data being collected, and the clients for which it is being collected. This table is indexed by tn3270eSrvrConfIndex and tn3270eClientGroupName imported from the TN3270E-MIB. tn3270eSrvrConfIndex indicates within a host which TN3270E server an entry applies to. tn3270eClientGroupName it identifies the set of IP clients for which response time data is being collected. The particular IP clients making up the set are identified in the tn3270eClientGroupTable in the TN3270E-MIB."White & Moore Standards Track [Page 27]
RFC 2562 TN3270E-RT-MIB April 1999 ::= { tn3270eRtObjects 1} tn3270eRtCollCtlEntry OBJECT-TYPE SYNTAX Tn3270eRtCollCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the TN3270E response time monitoring collection control table. To handle the case of multiple TN3270E servers on the same host, the first index of this table is the tn3270eSrvrConfIndex from the TN3270E-MIB." INDEX { tn3270eSrvrConfIndex, -- Server's index tn3270eClientGroupName } -- What to collect on ::= { tn3270eRtCollCtlTable 1 } Tn3270eRtCollCtlEntry ::= SEQUENCE { tn3270eRtCollCtlType BITS, tn3270eRtCollCtlSPeriod Unsigned32, tn3270eRtCollCtlSPMult Unsigned32, tn3270eRtCollCtlThreshHigh Unsigned32, tn3270eRtCollCtlThreshLow Unsigned32, tn3270eRtCollCtlIdleCount Unsigned32, tn3270eRtCollCtlBucketBndry1 Unsigned32, tn3270eRtCollCtlBucketBndry2 Unsigned32, tn3270eRtCollCtlBucketBndry3 Unsigned32, tn3270eRtCollCtlBucketBndry4 Unsigned32, tn3270eRtCollCtlRowStatus RowStatus } -- The OID { tn3270eRtCollCtlEntry 1 } is not used tn3270eRtCollCtlType OBJECT-TYPE SYNTAX BITS { aggregate(0), excludeIpComponent(1), ddr(2), average(3), buckets(4), traps(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls what types of response time data to collect, whether to summarize the data across the members of a client group or keep it individually, whether to introduce dynamic definite responses, and whether to generate traps.White & Moore Standards Track [Page 28]
RFC 2562 TN3270E-RT-MIB April 1999 aggregate(0) - Aggregate response time data for the client group as a whole. If this bit is set to 0, then maintain response time data separately for each member of the client group. excludeIpComponent(1) - Do not include the IP-network component in any response times. ddr(2) - Enable dynamic definite response. average(3) - Produce an average response time based on a specified collection interval. buckets(4) - Maintain tn3270eRtDataBucket values in a corresponding tn3270eRtDataEntry, based on the bucket boundaries specified in the tn3270eRtCollCtlBucketBndry objects . traps(5) - generate the notifications specified in this MIB module. The tn3270eRtExceeded and tn3270eRtOkay notifications are generated only if average(3) is also specified." ::= { tn3270eRtCollCtlEntry 2 } tn3270eRtCollCtlSPeriod OBJECT-TYPE SYNTAX Unsigned32 (15..86400) -- 15 second min, 24 hour max UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds that defines the sample period. The actual interval is defined as tn3270eRtCollCtlSPeriod times tn3270eRtCollCtlSPMult. The value of this object is used only if the corresponding tn3270eRtCollCtlType has the average(3) setting." DEFVAL {20} -- 20 seconds ::= { tn3270eRtCollCtlEntry 3 } tn3270eRtCollCtlSPMult OBJECT-TYPE SYNTAX Unsigned32 (1..5760) -- 5760 x SPeriod of 15 is 24 hours UNITS "period" MAX-ACCESS read-create STATUS current DESCRIPTION "The sample period multiplier; this value is multiplied by the sample period, tn3270eRtCollCtlSPeriod, to determine the collection interval.White & Moore Standards Track [Page 29]
RFC 2562 TN3270E-RT-MIB April 1999 Sliding-window average calculation can, if necessary, be disabled, by setting the sample period multiplier, tn3270eRtCollCtlSPMult, to 1, and setting the sample period, tn3270eRtCollCtlSPeriod, to the required collection interval. The value of this object is used only if the corresponding tn3270eRtCollCtlType has the average(3) setting." DEFVAL { 30 } -- yields an interval of 10 minutes when -- used with the default SPeriod value ::= { tn3270eRtCollCtlEntry 4 } tn3270eRtCollCtlThreshHigh OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The threshold for generating a tn3270eRtExceeded notification, signalling that a monitored total response time has exceeded the specified limit. A value of zero for this object suppresses generation of this notification. The value of this object is used only if the corresponding tn3270eRtCollCtlType has average(3) and traps(5) selected. A tn3270eRtExceeded notification is not generated again for a tn3270eRtDataEntry until an average response time falling below the low threshold tn3270eRtCollCtlThreshLow specified for the client group has occurred for the entry." DEFVAL { 0 } -- suppress notifications ::= { tn3270eRtCollCtlEntry 5 } tn3270eRtCollCtlThreshLow OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The threshold for generating a tn3270eRtOkay notification, signalling that a monitored total response time has fallen below the specified limit. A value of zero for this object suppresses generation of this notification. The value of this object is used only if the corresponding tn3270eRtCollCtlType has average(3) and traps(5) selected. A tn3270eRtOkay notification is not generated again for a tn3270eRtDataEntry until an average response timeWhite & Moore Standards Track [Page 30]
RFC 2562 TN3270E-RT-MIB April 1999 exceeding the high threshold tn3270eRtCollCtlThreshHigh specified for the client group has occurred for the entry." DEFVAL { 0 } -- suppress notifications ::= { tn3270eRtCollCtlEntry 6 } tn3270eRtCollCtlIdleCount OBJECT-TYPE SYNTAX Unsigned32 UNITS "transactions" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object is used to determine whether a sample that yields an average response time exceeding the value of tn3270eRtCollCtlThreshHigh was a statistically valid one. If the following statement is true, then the sample was statistically valid, and so a tn3270eRtExceeded notification should be generated: AvgCountTrans * ((AvgRt/ThreshHigh - 1) ** 2) >= IdleCount This comparison is done only if the corresponding tn3270eRtCollCtlType has average(3) and traps(5) selected." DEFVAL { 1 } ::= { tn3270eRtCollCtlEntry 7 } tn3270eRtCollCtlBucketBndry1 OBJECT-TYPE SYNTAX Unsigned32 UNITS "tenths of seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object defines the range of transaction response times counted in the Tn3270eRtDataBucket1Rts object: those less than or equal to this value." DEFVAL { 10 } ::= { tn3270eRtCollCtlEntry 8 } tn3270eRtCollCtlBucketBndry2 OBJECT-TYPE SYNTAX Unsigned32 UNITS "tenths of seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object, together with that of the tn3270eRtCollCtlBucketBndry1 object, defines the range of transaction response times counted in the Tn3270eRtDataBucket2Rts object: those greater than the value of the tn3270eRtCollCtlBucketBndry1 object, andWhite & Moore Standards Track [Page 31]
RFC 2562 TN3270E-RT-MIB April 1999 less than or equal to the value of this object." DEFVAL { 20 } ::= { tn3270eRtCollCtlEntry 9 } tn3270eRtCollCtlBucketBndry3 OBJECT-TYPE SYNTAX Unsigned32 UNITS "tenths of seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object, together with that of the tn3270eRtCollCtlBucketBndry2 object, defines the range of transaction response times counted in the Tn3270eRtDataBucket3Rts object: those greater than the value of the tn3270eRtCollCtlBucketBndry2 object, and less than or equal to the value of this object." DEFVAL { 50 } ::= { tn3270eRtCollCtlEntry 10 } tn3270eRtCollCtlBucketBndry4 OBJECT-TYPE SYNTAX Unsigned32 UNITS "tenths of seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object, together with that of the tn3270eRtCollCtlBucketBndry3 object, defines the range of transaction response times counted in the Tn3270eRtDataBucket4Rts object: those greater than the value of the tn3270eRtCollCtlBucketBndry3 object, and less than or equal to the value of this object. The value of this object also defines the range of transaction response times counted in the Tn3270eRtDataBucket5Rts object: those greater than the value of this object." DEFVAL { 100 } ::= { tn3270eRtCollCtlEntry 11 } tn3270eRtCollCtlRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object allows entries to be created and deleted in the tn3270eRtCollCtlTable. An entry in this table is deleted by setting this object to destroy(6). Deleting an entry in this table has the side-effectWhite & Moore Standards Track [Page 32]
RFC 2562 TN3270E-RT-MIB April 1999 of removing all entries from the tn3270eRtDataTable that are associated with the entry being deleted." ::= { tn3270eRtCollCtlEntry 12 } -- TN3270E Response Time Data Table tn3270eRtDataTable OBJECT-TYPE SYNTAX SEQUENCE OF Tn3270eRtDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The response time data table. Entries in this table are created based on entries in the tn3270eRtCollCtlTable." ::= { tn3270eRtObjects 2 } tn3270eRtDataEntry OBJECT-TYPE SYNTAX Tn3270eRtDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries in this table are created based upon the tn3270eRtCollCtlTable. When the corresponding tn3270eRtCollCtlType has aggregate(0) specified, a single entry is created in this table, with a tn3270eRtDataClientAddrType of unknown(0), a zero-length octet string value for tn3270eRtDataClientAddress, and a tn3270eRtDataClientPort value of 0. When aggregate(0) is not specified, a separate entry is created for each client in the group. Note that the following objects defined within an entry in this table can wrap: tn3270eRtDataTotalRts tn3270eRtDataTotalIpRts tn3270eRtDataCountTrans tn3270eRtDataCountDrs tn3270eRtDataElapsRnTrpSq tn3270eRtDataElapsIpRtSq tn3270eRtDataBucket1Rts tn3270eRtDataBucket2Rts tn3270eRtDataBucket3Rts tn3270eRtDataBucket4Rts tn3270eRtDataBucket5Rts" INDEX { tn3270eSrvrConfIndex, -- Server's local index tn3270eClientGroupName, -- Collection target tn3270eRtDataClientAddrType, tn3270eRtDataClientAddress,White & Moore Standards Track [Page 33]
RFC 2562 TN3270E-RT-MIB April 1999 tn3270eRtDataClientPort } ::= { tn3270eRtDataTable 1 } Tn3270eRtDataEntry ::= SEQUENCE { tn3270eRtDataClientAddrType IANATn3270eAddrType, tn3270eRtDataClientAddress IANATn3270eAddress, tn3270eRtDataClientPort Unsigned32, tn3270eRtDataAvgRt Gauge32, tn3270eRtDataAvgIpRt Gauge32, tn3270eRtDataAvgCountTrans Gauge32, tn3270eRtDataIntTimeStamp DateAndTime, tn3270eRtDataTotalRts Counter32, tn3270eRtDataTotalIpRts Counter32, tn3270eRtDataCountTrans Counter32, tn3270eRtDataCountDrs Counter32, tn3270eRtDataElapsRndTrpSq Unsigned32, tn3270eRtDataElapsIpRtSq Unsigned32, tn3270eRtDataBucket1Rts Counter32, tn3270eRtDataBucket2Rts Counter32, tn3270eRtDataBucket3Rts Counter32, tn3270eRtDataBucket4Rts Counter32, tn3270eRtDataBucket5Rts Counter32, tn3270eRtDataRtMethod INTEGER, tn3270eRtDataDiscontinuityTime TimeStamp } tn3270eRtDataClientAddrType OBJECT-TYPE SYNTAX IANATn3270eAddrType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates the type of address represented by the value of tn3270eRtDataClientAddress. The value unknown(0) is used if aggregate data is being collected for the client group." ::= { tn3270eRtDataEntry 1 } tn3270eRtDataClientAddress OBJECT-TYPE SYNTAX IANATn3270eAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the IP address of the TN3270 client being monitored. A zero-length octet string is used if aggregate data is being collected for the client group." ::= { tn3270eRtDataEntry 2 } tn3270eRtDataClientPort OBJECT-TYPEWhite & Moore Standards Track [Page 34]
RFC 2562 TN3270E-RT-MIB April 1999 SYNTAX Unsigned32(0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the client port number of the TN3270 client being monitored. The value 0 is used if aggregate data is being collected for the client group, or if the tn3270eRtDataClientAddrType identifies an address type that does not support ports." ::= { tn3270eRtDataEntry 3 } tn3270eRtDataAvgRt OBJECT-TYPE SYNTAX Gauge32 UNITS "tenths of seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average total response time measured over the last collection interval." DEFVAL { 0 } ::= { tn3270eRtDataEntry 4 } tn3270eRtDataAvgIpRt OBJECT-TYPE SYNTAX Gauge32 UNITS "tenths of seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The average IP response time measured over the last collection interval." DEFVAL { 0 } ::= { tn3270eRtDataEntry 5 } tn3270eRtDataAvgCountTrans OBJECT-TYPE SYNTAX Gauge32 UNITS "transactions" MAX-ACCESS read-only STATUS current DESCRIPTION "The sliding transaction count used for calculating the values of the tn3270eRtDataAvgRt and tn3270eRtDataAvgIpRt objects. The actual transaction count is available in the tn3270eRtDataCountTrans object. The initial value of this object, before any averages have been calculated, is 0." ::= { tn3270eRtDataEntry 6 }White & Moore Standards Track [Page 35]
RFC 2562 TN3270E-RT-MIB April 1999 tn3270eRtDataIntTimeStamp OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time of the last interval that tn3270eRtDataAvgRt, tn3270eRtDataAvgIpRt, and tn3270eRtDataAvgCountTrans were calculated. Prior to the calculation of the first interval averages, this object returns the value 0x0000000000000000000000. When this value is returned, the remaining objects in the entry have no significance." ::= { tn3270eRtDataEntry 7 } tn3270eRtDataTotalRts OBJECT-TYPE SYNTAX Counter32 UNITS "tenths of seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of the total response times collected. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 8 } tn3270eRtDataTotalIpRts OBJECT-TYPE SYNTAX Counter32 UNITS "tenths of seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of the total IP-network response times collected. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 9 } tn3270eRtDataCountTrans OBJECT-TYPE SYNTAX Counter32 UNITS "transactions" MAX-ACCESS read-only STATUS currentWhite & Moore Standards Track [Page 36]
RFC 2562 TN3270E-RT-MIB April 1999 DESCRIPTION "The count of the total number of transactions detected. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 10 } tn3270eRtDataCountDrs OBJECT-TYPE SYNTAX Counter32 UNITS "definite responses" MAX-ACCESS read-only STATUS current DESCRIPTION "The count of the total number of definite responses detected. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 11 } tn3270eRtDataElapsRndTrpSq OBJECT-TYPE SYNTAX Unsigned32 UNITS "tenths of seconds squared" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of the elapsed round trip time squared. The sum of the squares is kept in order to enable calculation of a variance." DEFVAL { 0 } ::= { tn3270eRtDataEntry 12 } tn3270eRtDataElapsIpRtSq OBJECT-TYPE SYNTAX Unsigned32 UNITS "tenths of seconds squared" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of the elapsed IP round trip time squared. The sum of the squares is kept in order to enable calculation of a variance." DEFVAL { 0 } ::= { tn3270eRtDataEntry 13 } tn3270eRtDataBucket1Rts OBJECT-TYPE SYNTAX Counter32White & Moore Standards Track [Page 37]
RFC 2562 TN3270E-RT-MIB April 1999 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of the response times falling into bucket 1. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 14 } tn3270eRtDataBucket2Rts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of the response times falling into bucket 2. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 15 } tn3270eRtDataBucket3Rts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of the response times falling into bucket 3. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 16 } tn3270eRtDataBucket4Rts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of the response times falling into bucket 4. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 17 } tn3270eRtDataBucket5Rts OBJECT-TYPE SYNTAX Counter32White & Moore Standards Track [Page 38]
RFC 2562 TN3270E-RT-MIB April 1999 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of the response times falling into bucket 5. A management application can detect discontinuities in this counter by monitoring the tn3270eRtDataDiscontinuityTime object." ::= { tn3270eRtDataEntry 18 } tn3270eRtDataRtMethod OBJECT-TYPE SYNTAX INTEGER { none(0), responses(1), timingMark(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the method that was used in calculating the IP network time. The value 'none(0) indicates that response times were not calculated for the IP network." ::= { tn3270eRtDataEntry 19 } tn3270eRtDataDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which one or more of this entry's counter objects suffered a discontinuity. This may happen if a TN3270E server is stopped and then restarted, and local methods are used to set up collection policy (tn3270eRtCollCtlTable entries)." ::= { tn3270eRtDataEntry 20 } tn3270eRtSpinLock OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "An advisory lock used to allow cooperating TN3270E-RT-MIB applications to coordinate their use of the tn3270eRtCollCtlTable.White & Moore Standards Track [Page 39]
RFC 2562 TN3270E-RT-MIB April 1999 When creating a new entry or altering an existing entry in the tn3270eRtCollCtlTable, an application should make use of tn3270eRtSpinLock to serialize application changes or additions. Since this is an advisory lock, the use of this lock is not enforced." ::= { tn3270eRtObjects 3 } -- Notifications tn3270eRtExceeded NOTIFICATION-TYPE OBJECTS { tn3270eRtDataIntTimeStamp, tn3270eRtDataAvgRt, tn3270eRtDataAvgIpRt, tn3270eRtDataAvgCountTrans, tn3270eRtDataRtMethod } STATUS current DESCRIPTION "This notification is generated when the average response time, tn3270eRtDataAvgRt, exceeds tn3270eRtCollCtlThresholdHigh at the end of a collection interval specified by tn3270eCollCtlSPeriod times tn3270eCollCtlSPMult. Note that the corresponding tn3270eCollCtlType must have traps(5) and average(3) set for this notification to be generated. In addition, tn3270eRtDataAvgCountTrans, tn3270eRtCollCtlThreshHigh, and tn3270eRtDataAvgRt are algorithmically compared to tn3270eRtCollCtlIdleCount for determination if this notification will be suppressed." ::= { tn3270eRtNotifications 1 } tn3270eRtOkay NOTIFICATION-TYPE OBJECTS { tn3270eRtDataIntTimeStamp, tn3270eRtDataAvgRt, tn3270eRtDataAvgIpRt, tn3270eRtDataAvgCountTrans, tn3270eRtDataRtMethod } STATUS current DESCRIPTION "This notification is generated when the average response time, tn3270eRtDataAvgRt, falls below tn3270eRtCollCtlThresholdLow at the end of a collection interval specified by tn3270eCollCtlSPeriod timesWhite & Moore Standards Track [Page 40]
RFC 2562 TN3270E-RT-MIB April 1999 tn3270eCollCtlSPMult, after a tn3270eRtExceeded notification was generated. Note that the corresponding tn3270eCollCtlType must have traps(5) and average(3) set for this notification to be generated." ::= { tn3270eRtNotifications 2 } tn3270eRtCollStart NOTIFICATION-TYPE OBJECTS { tn3270eRtDataRtMethod, -- type of collection tn3270eResMapElementType -- type of resource } STATUS current DESCRIPTION "This notification is generated when response time data collection is enabled for a member of a client group. In order for this notification to occur the corresponding tn3270eRtCollCtlType must have traps(5) selected. tn3270eResMapElementType contains a valid value only if tn3270eRtDataClientAddress contains a valid address (rather than a zero-length octet string)." ::= { tn3270eRtNotifications 3 } tn3270eRtCollEnd NOTIFICATION-TYPE OBJECTS { tn3270eRtDataDiscontinuityTime, tn3270eRtDataAvgRt, tn3270eRtDataAvgIpRt, tn3270eRtDataAvgCountTrans, tn3270eRtDataIntTimeStamp, tn3270eRtDataTotalRts, tn3270eRtDataTotalIpRts, tn3270eRtDataCountTrans, tn3270eRtDataCountDrs, tn3270eRtDataElapsRndTrpSq, tn3270eRtDataElapsIpRtSq, tn3270eRtDataBucket1Rts, tn3270eRtDataBucket2Rts, tn3270eRtDataBucket3Rts, tn3270eRtDataBucket4Rts, tn3270eRtDataBucket5Rts, tn3270eRtDataRtMethod } STATUS current DESCRIPTION "This notification is generated when an tn3270eRtDataEntry is deleted after being active (actual data collected), in order to enable a management application monitoring anWhite & Moore Standards Track [Page 41]
RFC 2562 TN3270E-RT-MIB April 1999 tn3270eRtDataEntry to get the entry's final values. Note that the corresponding tn3270eCollCtlType must have traps(5) set for this notification to be generated." ::= { tn3270eRtNotifications 4 } -- Conformance Statement tn3270eRtGroups OBJECT IDENTIFIER ::= { tn3270eRtConformance 1 } tn3270eRtCompliances OBJECT IDENTIFIER ::= { tn3270eRtConformance 2 } -- Compliance statements tn3270eRtCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that support the TN327E-RT-MIB." MODULE -- this module MANDATORY-GROUPS { tn3270eRtGroup, tn3270eRtNotGroup } OBJECT tn3270eRtCollCtlType MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlSPeriod MIN-ACCESS read-only DESCRIPTION "The agent is not required to allow the user to change the default value of this object, and is allowed to use a different default." OBJECT tn3270eRtCollCtlSPMult MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlThreshHigh MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlThreshLow MIN-ACCESS read-only DESCRIPTIONWhite & Moore Standards Track [Page 42]
RFC 2562 TN3270E-RT-MIB April 1999 "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlIdleCount MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlBucketBndry1 MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlBucketBndry2 MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlBucketBndry3 MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlBucketBndry4 MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object in the absence of adequate security." OBJECT tn3270eRtCollCtlRowStatus SYNTAX INTEGER { active(1) -- subset of RowStatus } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." ::= {tn3270eRtCompliances 1 } -- Group definitions tn3270eRtGroup OBJECT-GROUPWhite & Moore Standards Track [Page 43]
RFC 2562 TN3270E-RT-MIB April 1999 OBJECTS { tn3270eRtCollCtlType, tn3270eRtCollCtlSPeriod, tn3270eRtCollCtlSPMult, tn3270eRtCollCtlThreshHigh, tn3270eRtCollCtlThreshLow, tn3270eRtCollCtlIdleCount, tn3270eRtCollCtlBucketBndry1, tn3270eRtCollCtlBucketBndry2, tn3270eRtCollCtlBucketBndry3, tn3270eRtCollCtlBucketBndry4, tn3270eRtCollCtlRowStatus, tn3270eRtDataDiscontinuityTime, tn3270eRtDataAvgRt, tn3270eRtDataAvgIpRt, tn3270eRtDataAvgCountTrans, tn3270eRtDataIntTimeStamp, tn3270eRtDataTotalRts, tn3270eRtDataTotalIpRts, tn3270eRtDataCountTrans, tn3270eRtDataCountDrs, tn3270eRtDataElapsRndTrpSq, tn3270eRtDataElapsIpRtSq, tn3270eRtDataBucket1Rts, tn3270eRtDataBucket2Rts, tn3270eRtDataBucket3Rts, tn3270eRtDataBucket4Rts, tn3270eRtDataBucket5Rts, tn3270eRtDataRtMethod, tn3270eRtSpinLock } STATUS current DESCRIPTION "This group is mandatory for all implementations that support the TN3270E-RT-MIB. " ::= { tn3270eRtGroups 1 } tn3270eRtNotGroup NOTIFICATION-GROUP NOTIFICATIONS { tn3270eRtExceeded, tn3270eRtOkay, tn3270eRtCollStart, tn3270eRtCollEnd }White & Moore Standards Track [Page 44]
RFC 2562 TN3270E-RT-MIB April 1999 STATUS current DESCRIPTION "The notifications that must be supported when the TN3270E-RT-MIB is implemented. " ::= { tn3270eRtGroups 2 } END6.0 Security Considerations Certain management information defined in this MIB may be considered sensitive in some network environments. Therefore, authentication of received SNMP requests and controlled access to management information SHOULD be employed in such environments. An authentication protocol is defined in [12]. A protocol for access control is defined in [15]. Several objects in this MIB allow write access or provide for row creation. Allowing this support in a non-secure environment can have a negative effect on network operations. It is RECOMMENDED that implementers seriously consider whether set operations or row creation SHOULD be allowed without providing, at a minimum, authentication of request origin. It is RECOMMENDED that without such support that the following objects be implemented as read-only: o tn3270eRtCollCtlType o tn3270eRtCollCtlSPeriod o tn3270eRtCollCtlSPMult o tn3270eRtCollCtlThreshHigh o tn3270eRtCollCtlThreshLow o tn3270eRtCollCtlIdleCount o tn3270eRtCollCtlBucketBndry1 o tn3270eRtCollCtlBucketBndry2 o tn3270eRtCollCtlBucketBndry3 o tn3270eRtCollCtlBucketBndry4 o tn3270eRtCollCtlRowStatus The administrative method to use to create and manage the tn3270eRtCollCtlTable when SET support is not allowed is outside of the scope of this memo.7.0 Intellectual Property The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rightsWhite & Moore Standards Track [Page 45]
RFC 2562 TN3270E-RT-MIB April 1999 might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found inBCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director.8.0 Acknowledgments This document is a product of the TN3270E Working Group. Special thanks are due to Derek Bolton and Michael Boe of Cisco Systems for their numerous comments and suggestions for improving the structure of this MIB. Thanks also to Randy Presuhn of BMC Software for his valuable review comments on several versions of the document.9.0 References [1] Harrington D., Presuhn, R. and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks",RFC 2271, January 1998. [2] Rose, M. and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", STD 16,RFC1155, May 1990. [3] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16,RFC 1212, March 1991. [4] Rose, M., "A Convention for Defining Traps for use with the SNMP",RFC 1215, March 1991. [5] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1902, January 1996. [6] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1903, January 1996.White & Moore Standards Track [Page 46]
RFC 2562 TN3270E-RT-MIB April 1999 [7] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1904, January 1996. [8] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple Network Management Protocol", STD 15,RFC 1157, May 1990. [9] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Introduction to Community-based SNMPv2",RFC 1901, January 1996. [10] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1906, January 1996. [11] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)",RFC 2272, January 1998. [12] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)",RFC 2274, January 1998. [13] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)",RFC 1905, January 1996. [14] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications",RFC2273, January 1998. [15] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)",RFC 2275, January 1998. [16] Postel, J. and J. Reynolds, "Telnet Protocol Specification", STD 8,RFC 854, May 1983. [17] Postel, J. and J. Reynolds, "Telnet Timing Mark Option", STD 31,RFC 860, May 1983. [18] Rekhter, J., "Telnet 3270 Regime Option",RFC 1041, January 1988. [19] Kelly, B., "TN3270 Enhancements",RFC 2355, June 1998. [20] White, K. and R. Moore, "Base Definitions of Managed Objects for TN3270E Using SMIv2",RFC 2561, April 1999.White & Moore Standards Track [Page 47]
RFC 2562 TN3270E-RT-MIB April 1999 [21] IBM, International Technical Support Centers, "Response Time Data Gathering", GG24-3212-01, November 1990. [22] Hovey, R. and S. Bradner, "The Organizations Involved in the IETF Standards Process",BCP 11,RFC 2028, October 1996. [23] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels",BCP 14,RFC 2119, March 1997.10.0 Authors' Addresses Kenneth D. White Dept. BRQA/Bldg. 501/G114 IBM Corporation P.O.Box 12195 3039 Cornwallis Research Triangle Park, NC 27709, USA EMail: kennethw@vnet.ibm.com Robert Moore Dept. BRQA/Bldg. 501/G114 IBM Corporation P.O.Box 12195 3039 Cornwallis Research Triangle Park, NC 27709, USA Phone: +1-919-254-7507 EMail: remoore@us.ibm.comWhite & Moore Standards Track [Page 48]
RFC 2562 TN3270E-RT-MIB April 199911.0 Full Copyright Statement Copyright (C) The Internet Society (1999). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.White & Moore Standards Track [Page 49]
[8]ページ先頭