Movatterモバイル変換

[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]

PROPOSED STANDARD

Network Working Group                                         J.-H. ChenRequest for Comments: 4298                                        W. LeeCategory: Standards Track                                     J. Thyssen                                                    Broadcom Corporation                                                           December 2005RTP Payload Format for BroadVoice Speech CodecsStatus of This Memo   This document specifies an Internet standards track protocol for the   Internet community, and requests discussion and suggestions for   improvements.  Please refer to the current edition of the "Internet   Official Protocol Standards" (STD 1) for the standardization state   and status of this protocol.  Distribution of this memo is unlimited.Copyright Notice   Copyright (C) The Internet Society (2005).Abstract   This document describes the RTP payload format for the BroadVoice(R)   narrowband and wideband speech codecs.  The narrowband codec, called   BroadVoice16, or BV16, has been selected by CableLabs as a mandatory   codec in PacketCable 1.5 and has a CableLabs specification.  The   document also provides specifications for the use of BroadVoice with   MIME and the Session Description Protocol (SDP).Chen, et al.                Standards Track                     [Page 1]

RFC 4298 RTP Payload Format for BroadVoice December 2005Table of Contents1. Introduction ....................................................22. Background ......................................................23. RTP Payload Format for BroadVoice16 Narrowband Codec ............33.1. BroadVoice16 Bit Stream Definition .........................43.2. Multiple BroadVoice16 Frames in an RTP Packet ..............54. RTP Payload Format for BroadVoice32 Wideband Codec ..............64.1. BroadVoice32 Bit Stream Definition .........................64.2. Multiple BroadVoice32 Frames in an RTP Packet ..............85. IANA Considerations .............................................85.1. MIME Registration of BroadVoice16 for RTP ..................95.2. MIME Registration of BroadVoice32 for RTP ..................96. Mapping to SDP Parameters ......................................106.1. Offer-Answer Model Considerations .........................117. Security Considerations ........................................118. Congestion Control .............................................119. Acknowledgements ...............................................1110. References ....................................................1210.1. Normative References .....................................1210.2. Informative References ...................................121. Introduction This document specifies the payload format for sending BroadVoice encoded speech or audio signals using the Real-time Transport Protocol (RTP) [1]. The sender may send one or more BroadVoice codec data frames per packet, depending on the application scenario, based on network conditions, bandwidth availability, delay requirements, and packet-loss tolerance. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described inRFC 2119 [2].2. Background BroadVoice is a speech codec family developed for VoIP (Voice over Internet Protocol) applications, including Voice over Cable, Voice over DSL, and IP phone applications. BroadVoice achieves high speech quality with a low coding delay and relatively low codec complexity. The BroadVoice codec family contains two codec versions. The narrowband version of BroadVoice, called BroadVoice16 [3], or BV16 for short, encodes 8 kHz-sampled narrowband speech at a bit rate of 16 kilobits/second, or 16 kbit/s. The wideband version of BroadVoice, called BroadVoice32, or BV32, encodes 16 kHz-sampled wideband speech at a bit rate of 32 kbit/s. The BV16 and BV32 useChen, et al. Standards Track [Page 2]

RFC 4298           RTP Payload Format for BroadVoice       December 2005   very similar (but not identical) coding algorithms; they share most   of their algorithm modules.   To minimize the delay in real-time two-way communications, both the   BV16 and BV32 encode speech with a very small frame size of 5 ms   without using any look ahead.  By using a packet size as small as 5   ms if necessary, this allows VoIP systems based on BroadVoice to have   a very low end-to-end system delay.   BroadVoice also has relatively low codec complexity when compared   with ITU-T standard speech codecs based on CELP (Coded Excited Linear   Prediction), such as G.728, G.729, G.723.1, and G.722.2.  Full-duplex   implementations of the BV16 and BV32 take around 12 and 17 MIPS,   respectively, on general-purpose 16-bit fixed-point digital signal   processors (DSPs).  The total memory footprints of the BV16 and BV32,   including program size, data tables, and data RAM, are around 12   kwords each, or 24 kbytes.   The PacketCable(TM) project of Cable Television Laboratories, Inc.   (CableLabs(R)) has chosen the BV16 codec for use in VoIP telephone   services provided by cable operators.  More specifically, the BV16   codec was selected as one of the mandatory audio codecs in the   PacketCable(TM) 1.5 Audio/Video Codecs Specification [8] and has been   implemented by multiple vendors.  The wideband version (BV32) has   been developed by Broadcom but has not yet appeared in a public   specification; since it is technically very similar to BV16, its   payload format is also defined in this document.3.  RTP Payload Format for BroadVoice16 Narrowband Codec   The BroadVoice16 uses 5 ms frames and a sampling frequency of 8 kHz,   so the RTP timestamp MUST be in units of 1/8000 of a second.  The RTP   timestamp indicates the sampling instant of the oldest audio sample   represented by the frame(s) present in the payload.  The RTP payload   for the BroadVoice16 has the format shown in the figure below.  No   additional header specific to this payload format is required.    0                   1                   2                   3    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |                      RTP Header [1]                           |   +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+   |                                                               |   |             one or more frames of BroadVoice16                |   |                                                               |   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+Chen, et al.                Standards Track                     [Page 3]

RFC 4298 RTP Payload Format for BroadVoice December 2005 If BroadVoice16 is used for applications with silence compression, the first BroadVoice16 packet after a silence period during which packets have not been transmitted contiguously SHOULD have the marker bit in the RTP data header set to one. The marker bit in all other packets is zero. Applications without silence suppression MUST set the marker bit to zero. The assignment of an RTP payload type for this new packet format is outside the scope of this document, and will not be specified here. It is expected that the RTP profile for a particular class of applications will assign a payload type for this encoding, or if that is not done, then a payload type in the dynamic range shall be chosen.3.1. BroadVoice16 Bit Stream Definition The BroadVoice16 encoder operates on speech frames of 5 ms corresponding to 40 samples at a sampling rate of 8000 samples per second. For every 5 ms frame, the encoder encodes the 40 consecutive audio samples into 80 bits, or 10 octets. Thus, the 80-bit bit stream produced by the BroadVoice16 for each 5 ms frame is octet- aligned, and no padding bits are required. The bit allocation for the encoded parameters of the BroadVoice16 codec is listed in the following table. Encoded Parameter Codeword Number of bits per frame ------------------------------------------------------------ Line Spectrum Pairs L0,L1 7+7=14 Pitch Lag PL 7 Pitch Gain PG 5 Log-Gain LG 4 Excitation Vectors V0,...,V9 5*10=50 ------------------------------------------------------------ Total: 80 bits The mapping of the encoded parameters in an 80-bit BroadVoice16 data frame is defined in the following figure. This figure shows the bit packing in "network byte order", also known as big-endian order. The bits of each 32-bit word are numbered 0 to 31, with the most significant bit on the left and numbered 0. The octets (bytes) of each word are transmitted with the most significant octet first. The bits of the data field for each encoded parameter are numbered in the same order, with the most significant bit on the left.Chen, et al. Standards Track [Page 4]

RFC 4298           RTP Payload Format for BroadVoice       December 2005    0                   1                   2                   3    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |     L0      |     L1      |      PL     |   PG    |  LG   | V0|   |             |             |             |         |       |   |   |0 1 2 3 4 5 6|0 1 2 3 4 5 6|0 1 2 3 4 5 6|0 1 2 3 4|0 1 2 3|0 1|   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   | V0  |    V1   |    V2   |    V3   |    V4   |    V5   |   V6  |   |     |         |         |         |         |         |       |   |2 3 4|0 1 2 3 4|0 1 2 3 4|0 1 2 3 4|0 1 2 3 4|0 1 2 3 4|0 1 2 3|   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |V|    V7   |    V8   |   V9    |   |6|         |         |         |   |4|0 1 2 3 4|0 1 2 3 4|0 1 2 3 4|   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                      Figure 1: BroadVoice16 bit packing3.2.  Multiple BroadVoice16 Frames in an RTP Packet   More than one BroadVoice16 frame MAY be included in a single RTP   packet by a sender.  Senders have the following additional   restrictions:      o  SHOULD NOT include more BroadVoice16 frames in a single RTP         packet than will fit in the MTU of the RTP.      o  MUST NOT split a BroadVoice16 frame between RTP packets.      o  BroadVoice16 frames in an RTP packet MUST be consecutive.   Since multiple BroadVoice16 frames in an RTP packet MUST be   consecutive, and since BroadVoice16 has a fixed frame size of 5 ms,   recovering the timestamps of all frames within a packet is easy.  The   oldest frame within an RTP packet has the same timestamp as the RTP   packet, as mentioned above.  To obtain the timestamp of the frame   that is N frames later than the oldest frame in the packet, one   simply adds 5*N ms worth of time units to the timestamp of the RTP   packet.   It is RECOMMENDED that the number of frames contained within an RTP   packet be consistent with the application.  For example, in a   telephony application where delay is important, the fewer frames per   packet, the lower the delay; whereas, for a delay insensitive   streaming or messaging application, many frames per packet would be   acceptable.Chen, et al.                Standards Track                     [Page 5]

RFC 4298           RTP Payload Format for BroadVoice       December 2005   Information describing the number of frames contained in an RTP   packet is not transmitted as part of the RTP payload.  The only way   to determine the number of BroadVoice16 frames is to count the total   number of octets within the RTP payload, and divide the octet count   by 10.4.  RTP Payload Format for BroadVoice32 Wideband Codec   The BroadVoice32 uses 5 ms frames and a sampling frequency of 16 kHz,   so the RTP timestamp MUST be in units of 1/16000 of a second.  The   RTP timestamp indicates the sampling instant of the oldest audio   sample represented by the frame(s) present in the payload.  The RTP   payload for the BroadVoice32 has the format shown in the figure   below.  No additional header specific to this payload format is   required.    0                   1                   2                   3    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |                      RTP Header [1]                           |   +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+   |                                                               |   |             one or more frames of BroadVoice32                |   |                                                               |   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   If BroadVoice32 is used for applications with silence compression,   the first BroadVoice32 packet after a silence period during which   packets have not been transmitted contiguously SHOULD have the marker   bit in the RTP data header set to one.  The marker bit in all other   packets is zero.  Applications without silence suppression MUST set   the marker bit to zero.   The assignment of an RTP payload type for this new packet format is   outside the scope of this document, and will not be specified here.   It is expected that the RTP profile for a particular class of   applications will assign a payload type for this encoding, or if that   is not done, then a payload type in the dynamic range shall be   chosen.4.1.  BroadVoice32 Bit Stream Definition   The BroadVoice32 encoder operates on speech frames of 5 ms   corresponding to 80 samples at a sampling rate of 16000 samples per   second.  For every 5 ms frame, the encoder encodes the 80 consecutive   audio samples into 160 bits, or 20 octets.  Thus, the 160-bit bit   stream produced by the BroadVoice32 for each 5 ms frame is octet-   aligned, and no padding bits are required.  The bit allocation forChen, et al.                Standards Track                     [Page 6]

RFC 4298           RTP Payload Format for BroadVoice       December 2005   the encoded parameters of the BroadVoice32 codec is listed in the   following table.                                                        Number of bits      Encoded Parameter                  Codeword       per frame      ---------------------------------------------------------------      Line Spectrum Pairs                L0,L1,L2       7+5+5=17      Pitch Lag                          PL                    8      Pitch Gain                         PG                    5      Log-Gains (1st & 2nd subframes)    LG0,LG1          5+5=10      Excitation Vectors (1st subframe)  VA0,...,VA9     6*10=60      Excitation Vectors (2nd subframe)  VB0,...,VB9     6*10=60      ---------------------------------------------------------------      Total:                                                 160 bits   The mapping of the encoded parameters in a 160-bit BroadVoice32 data   frame is defined in the following figure.  This figure shows the bit   packing in "network byte order", also known as big-endian order.  The   bits of each 32-bit word are numbered 0 to 31, with the most   significant bit on the left and numbered 0.  The octets (bytes) of   each word are transmitted with the most significant octet first.  The   bits of the data field for each encoded parameter are numbered in the   same order, with the most significant bit on the left.    0                   1                   2                   3    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |     L0      |    L1   |    L2   |       PL      |    PG   |LG0|   |             |         |         |               |         |   |   |0 1 2 3 4 5 6|0 1 2 3 4|0 1 2 3 4|0 1 2 3 4 5 6 7|0 1 2 3 4|0 1|   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   | LG0 |   LG1   |    VA0    |    VA1    |    VA2    |    VA3    |   |     |         |           |           |           |           |   |2 3 4|0 1 2 3 4|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |    VA4    |    VA5    |    VA6    |    VA7    |    VA8    |VA9|   |           |           |           |           |           |   |   |0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1|   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   | VA9   |    VB0    |    VB1    |    VB2    |    VB3    |  VB4  |   |       |           |           |           |           |       |   |2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3|   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+   |VB4|    VB5    |    VB6    |    VB7    |    VB8    |   VB9     |   |   |           |           |           |           |           |   |4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|0 1 2 3 4 5|   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                  Figure 2: BroadVoice32 bit packingChen, et al.                Standards Track                     [Page 7]

RFC 4298 RTP Payload Format for BroadVoice December 20054.2. Multiple BroadVoice32 Frames in an RTP Packet More than one BroadVoice32 frame MAY be included in a single RTP packet by a sender. Senders have the following additional restrictions: o SHOULD NOT include more BroadVoice32 frames in a single RTP packet than will fit in the MTU of the RTP. o MUST NOT split a BroadVoice32 frame between RTP packets. o BroadVoice32 frames in an RTP packet MUST be consecutive. Since multiple BroadVoice32 frames in an RTP packet MUST be consecutive, and since BroadVoice32 has a fixed frame size of 5 ms, recovering the timestamps of all frames within a packet is easy. The oldest frame within an RTP packet has the same timestamp as the RTP packet, as mentioned above. To obtain the timestamp of the frame that is N frames later than the oldest frame in the packet, one simply adds 5*N ms worth of time units to the timestamp of the RTP packet. It is RECOMMENDED that the number of frames contained within an RTP packet be consistent with the application. For example, in a telephony application where delay is important, the fewer frames per packet, the lower the delay; whereas, for a delay insensitive streaming or messaging application, many frames per packet would be acceptable. Information describing the number of frames contained in an RTP packet is not transmitted as part of the RTP payload. The only way to determine the number of BroadVoice32 frames is to count the total number of octets within the RTP payload, and divide the octet count by 20.5. IANA Considerations Two new MIME sub-types, as described in this section, have been registered. The MIME names for the BV16 and BV32 codecs have been allocated from the IETF tree since these two codecs are expected to be widely used for Voice-over-IP applications, especially in Voice over Cable applications.Chen, et al. Standards Track [Page 8]

RFC 4298 RTP Payload Format for BroadVoice December 20055.1. MIME Registration of BroadVoice16 for RTP MIME media type name: audio MIME media subtype name: BV16 Required parameter: none Optional parameters: ptime: Defined as usual for RTP audio (seeRFC 2327 [4]). maxptime: SeeRFC 3267 [7] for its definition. The maxptime SHOULD be a multiple of the duration of a single codec data frame (5 ms). Encoding considerations: This type is defined for transferring BV16-encoded data via RTP using the payload format specified inSection 3 of RFC 4298. Audio data is binary data and must be encoded for non-binary transport; the Base64 encoding is suitable for Email. Security considerations: SeeSection 7 "Security Considerations" ofRFC 4298. Public specification: The BroadVoice16 codec has been specified in [3]. Intended usage: COMMON. It is expected that many VoIP applications, especially Voice over Cable applications, will use this type. Person & email address to contact for further information: Juin-Hwey (Raymond) Chen rchen@broadcom.com Author/Change controller: Author: Juin-Hwey (Raymond) Chen, rchen@broadcom.com Change Controller: IETF Audio/Video Transport Working Group delegated from the IESG5.2. MIME Registration of BroadVoice32 for RTP MIME media type name: audio MIME media subtype name: BV32 Required parameter: noneChen, et al. Standards Track [Page 9]

RFC 4298           RTP Payload Format for BroadVoice       December 2005   Optional parameters:      ptime:    Defined as usual for RTP audio (seeRFC 2327 [4]).      maxptime: SeeRFC 3267 [7] for its definition.  The maxptime         SHOULD be a multiple of the duration of a single codec data         frame (5 ms).   Encoding considerations:      This type is defined for transferring BV32-encoded data via RTP      using the payload format specified inSection 4 of RFC 4298.      Audio data is binary data and must be encoded for non-binary      transport; the Base64 encoding is suitable for Email.   Security considerations:      SeeSection 7 "Security Considerations" ofRFC 4298.   Intended usage:      COMMON.  It is expected that many VoIP applications, especially      Voice over Cable applications, will use this type.   Person & email address to contact for further information:      Juin-Hwey (Raymond) Chen      rchen@broadcom.com   Author/Change controller:      Author: Juin-Hwey (Raymond) Chen, rchen@broadcom.com      Change Controller: IETF Audio/Video Transport Working Group         delegated from the IESG6.  Mapping to SDP Parameters   The information carried in the MIME media type specification has a   specific mapping to fields in the Session Description Protocol (SDP)   [4], which is commonly used to describe RTP sessions.  When SDP is   used to specify sessions employing the BroadVoice16 or BroadVoice32   codec, the mapping is as follows:      -  The MIME type ("audio") goes in SDP "m=" as the media name.      -  The MIME subtype (payload format name) goes in SDP "a=rtpmap"         as the encoding name.  The RTP clock rate in "a=rtpmap" MUST be         8000 for BV16 and 16000 for BV32.      -  The parameters "ptime" and "maxptime" go in the SDP "a=ptime"         and "a=maxptime" attributes, respectively.Chen, et al.                Standards Track                    [Page 10]

RFC 4298 RTP Payload Format for BroadVoice December 2005 An example of the media representation in SDP for describing BV16 might be: m=audio 49120 RTP/AVP 97 a=rtpmap:97 BV16/8000 An example of the media representation in SDP for describing BV32 might be: m=audio 49122 RTP/AVP 99 a=rtpmap:99 BV32/160006.1. Offer-Answer Model Considerations No special considerations are needed for using the SDP Offer/Answer model [5] with the BV16 and BV32 RTP payload formats.7. Security Considerations RTP packets using the payload format defined in this specification are subject to the security considerations discussed in the RTP specification [1] and any appropriate profile (for example, [6]). This implies that confidentiality of the media streams is achieved by encryption. A potential denial-of-service threat exists for data encoding using compression techniques that have non-uniform receiver-end computational load. The attacker can inject pathological datagrams into the stream that are complex to decode and cause the receiver to become overloaded. However, the encodings covered in this document do not exhibit any significant non-uniformity.8. Congestion Control The general congestion control considerations for transporting RTP data apply to BV16 and BV32 audio over RTP as well (see RTP [1]) and any applicable RTP profile like AVP [6]. BV16 and BV32 do not have any built-in mechanism for reducing the bandwidth. Packing more frames in each RTP payload can reduce the number of packets sent, and hence the overhead from IP/UDP/RTP headers, at the expense of increased delay and reduced error robustness against packet losses.9. Acknowledgements The authors would like to thank Magnus Westerlund, Colin Perkins, Allison Mankin, and Jean-Francois Mule for their review of this document.Chen, et al. Standards Track [Page 11]

RFC 4298           RTP Payload Format for BroadVoice       December 200510.  References10.1.  Normative References   [1] Schulzrinne, H.,  Casner, S., Frederick, R., and V. Jacobson,       "RTP: A Transport Protocol for Real-Time Applications", STD 64,RFC 3550, July 2003.   [2] Bradner, S., "Key words for use in RFCs to Indicate Requirement       Levels",BCP 14,RFC 2119, March 1997.   [3] Cable Television Laboratories, Inc., BroadVoice(TM)16 Speech       Codec Specification, Revision 1.2, October 30, 2003.   [4] Handley, M. and V. Jacobson, "SDP: Session Description Protocol",RFC 2327, April 1998.   [5] Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model with       Session Description Protocol (SDP)",RFC 3264, June 2002.   [6] Schulzrinne, H. and S. Casner, "RTP Profile for Audio and Video       Conferences with Minimal Control", STD 65,RFC 3551, July 2003.   [7] Sjoberg, J., Westerlund, M., Lakaniemi, A., and Q. Xie, "Real-       Time Transport Protocol (RTP) Payload Format and File Storage       Format for the Adaptive Multi-Rate (AMR) and Adaptive Multi-Rate       Wideband (AMR-WB) Audio Codecs",RFC 3267, June 2002.10.2.  Informative References   [8] Cable Television Laboratories, Inc., PacketCable(TM) 1.5       Audio/Video Codecs Specification, PKT-SP-CODEC1.5-I01-050128,       January 28, 2005.http://www.cablelabs.com/specifications/archives/Chen, et al.                Standards Track                    [Page 12]

RFC 4298           RTP Payload Format for BroadVoice       December 2005Authors' Addresses   Juin-Hwey (Raymond) Chen   Broadcom Corporation   Room A3020   16215 Alton Parkway   Irvine, CA 92618   USA   Phone: +1 949 926 6288   EMail: rchen@broadcom.com   Winnie Lee   Broadcom Corporation   Room A2012E   200-13711 International Place   Richmond, British Columbia V6V 2Z8   Canada   Phone: +1 604 233 8605   EMail: wlee@broadcom.com   Jes Thyssen   Broadcom Corporation   Room A3018   16215 Alton Parkway   Irvine, CA 92618   USA   Phone: +1 949 926 5768   EMail: jthyssen@broadcom.comChen, et al.                Standards Track                    [Page 13]

RFC 4298           RTP Payload Format for BroadVoice       December 2005Full Copyright Statement   Copyright (C) The Internet Society (2005).   This document is subject to the rights, licenses and restrictions   contained inBCP 78, and except as set forth therein, the authors   retain all their rights.   This document and the information contained herein are provided on an   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.Intellectual Property   The IETF takes no position regarding the validity or scope of any   Intellectual Property Rights or other rights that might be claimed to   pertain to the implementation or use of the technology described in   this document or the extent to which any license under such rights   might or might not be available; nor does it represent that it has   made any independent effort to identify any such rights.  Information   on the procedures with respect to rights in RFC documents can be   found inBCP 78 andBCP 79.   Copies of IPR disclosures made to the IETF Secretariat and any   assurances of licenses to be made available, or the result of an   attempt made to obtain a general license or permission for the use of   such proprietary rights by implementers or users of this   specification can be obtained from the IETF on-line IPR repository athttp://www.ietf.org/ipr.   The IETF invites any interested party to bring to its attention any   copyrights, patents or patent applications, or other proprietary   rights that may cover technology that may be required to implement   this standard.  Please address the information to the IETF at ietf-   ipr@ietf.org.Acknowledgement   Funding for the RFC Editor function is currently provided by the   Internet Society.Chen, et al.                Standards Track                    [Page 14]

[8]ページ先頭