Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Errata] [Info page]
PROPOSED STANDARD
Errata ExistNetwork Working Group C. KuglerRequest for Comments: 3998 H. LewisCategory: Standards Track IBM Corporation T. Hastings, Ed. Xerox Corporation March 2005Internet Printing Protocol (IPP):Job and Printer Administrative OperationsStatus of This Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.Copyright Notice Copyright (C) The Internet Society (2005).Abstract This document specifies the following 16 additional OPTIONAL system administration operations for use with the Internet Printing Protocol/1.1 (IPP), plus a few associated attributes, values, and status codes, and using the IPP Printer object to manage printer fan-out and fan-in. Printer operations: Job operations: Enable-Printer and Disable-Printer Reprocess-Job Pause-Printer-After-Current-Job Cancel-Current-Job Hold-New-Jobs and Release-Held-New-Jobs Suspend-Current-Job Deactivate-Printer and Activate-Printer Resume-Job Restart-Printer Promote-Job Shutdown-Printer and Startup-Printer Schedule-Job-AfterKugler, et al. Standards Track [Page 1]
RFC 3998 IPP: Job and Printer Operations March 2005Table of Contents1. Introduction..................................................42. Terminology...................................................42.1. Conformance Terminology.................................42.2. Other Terminology.......................................53. Definition of the Printer Operations..........................63.1. The Disable and Enable Printer Operations...............73.1.1. Disable-Printer Operation.......................73.1.2. Enable-Printer Operation........................83.2. The Pause and Resume Printer Operations.................83.2.1. Pause-Printer-After-Current-Job Operation.......93.3. Hold and Release New Jobs Operations....................113.3.1. Hold-New-Jobs Operation.........................113.3.2. Release-Held-New-Jobs Operation.................123.4. Deactivate and Activate Printer Operations..............123.4.1. Deactivate-Printer Operation....................133.4.2. Activate-Printer Operation......................13 3.5. Restart-Printer, Shutdown-Printer, and Startup-Printer Operations..........................143.5.1. Restart-Printer Operation.......................143.5.2. Shutdown-Printer Operation......................143.5.3. Startup-Printer Operation.......................154. Definition of the Job Operations..............................164.1. Reprocess-Job Operation.................................174.2. Cancel-Current-Job Operation............................174.3. Suspend and Resume Job Operations.......................184.3.1. Suspend-Current-Job Operation...................194.3.2. Resume-Job Operation............................204.4. Job Scheduling Operations...............................204.4.1. Promote-Job Operation...........................204.4.2. Schedule-Job-After Operation....................215. Additional Status Codes.......................................235.1. 'server-error-printer-is-deactivated' (0x050A)..........23 6. Use of Operation Attributes That Are Messages from the Operator...........................237. New Printer Description Attributes............................267.1. subordinate-printers-supported (1setOf uri).............267.2. parent-printers-supported (1setOf uri)..................26 8. Additional Values for the "printer-state-reasons" Printer Description Attribute.....268.1. 'hold-new-jobs' Value...................................278.2. 'deactivated' Value.....................................27 9. Additional Values for the "job-state-reasons" Job Description attribute.............279.1. 'job-suspended' Value...................................27 10. Use of the Printer Object to Represent IPP Printer Fan-Out and IPP Printer Fan-In....................27Kugler, et al. Standards Track [Page 2]
RFC 3998 IPP: Job and Printer Operations March 200510.1. IPP Printer Fan-Out.....................................2810.2. IPP Printer Fan-In......................................28 10.3. Printer Object Attributes Used to Represent Printer Fan-Out and Printer Fan-In.........2910.4. Subordinate Printer URI.................................29 10.5. Printer Object Attributes Used to Represent Output Device Fan-Out......................3010.6. Figures to Show All Possible Configurations.............3010.7. Forwarding Requests.....................................33 10.7.1. Forwarding Requests that Affect Printer Objects.....................3310.7.2. Forwarding Requests that Affect Jobs............3510.8. Additional Attributes to Help with Fan-Out..............37 10.8.1. output-device-assigned (name(127)) Job Description Attribute - from [RFC2911]......37 10.8.2. original-requesting-user-name (name(MAX)) Operation and Job Description Attribute.........37 10.8.3. requesting-user-name (name(MAX)) Operation Attribute - Additional Semantics......38 10.8.4. job-originating-user-name (name(MAX)) Job Description Attribute - Additional Semantics............................3811. Conformance Requirements......................................3812. Normative References..........................................3913. Informative References........................................4014. IANA Considerations...........................................4014.1. Attribute Registrations.................................4114.2. Attribute Value Registrations...........................4114.3. Additional Enum Attribute Value Registrations...........4114.4. Operation Registrations.................................4214.5. Status Code Registrations...............................4315. Internationalization Considerations...........................4316. Security Considerations.......................................4317. Summary of Base IPP Documents.................................44 Authors' Addresses................................................45 Full Copyright Statement..........................................46List of Tables Table 1. Printer Operation Operation-Id Assignments..............6 Table 2. Pause and Resume Printer Operations.....................9 Table 3. State Transition Table for Pause-Printer-After-Current-Job Operation...............10 Table 4. Job Operation Operation-Id Assignments..................16 Table 5. Operation Attribute Support for Printer Operations......24 Table 6. Operation Attribute Support for Job Operations..........25 Table 7. Forwarding Operations that Affect Printer Objects.......34 Table 8. Forwarding Operations that Affect Jobs Objects..........36Kugler, et al. Standards Track [Page 3]
RFC 3998 IPP: Job and Printer Operations March 2005 Table 9. Conformance Requirement Dependencies for Operations.....38 Table 10. Conformance Requirement Dependencies for "printer-state-reasons" Values......................39 Table 11. Conformance Requirement Dependencies for "job-state-reasons" Values..........................39List of Figures Figure 1. Embedded Printer Object................................31 Figure 2. Hosted Printer Object..................................31 Figure 3. Output Device Fan-Out..................................31 Figure 4. Chained IPP Printer Objects............................32 Figure 5. IPP Printer Object Fan-Out.............................32 Figure 6. IPP Printer Object Fan-In..............................331. Introduction The Internet Printing Protocol (IPP) is an application level protocol that can be used for distributed printing using Internet tools and technologies. IPP version 1.1 ([RFC2911,RFC2910]) focuses on end- user functionality, with a few administrative operations included. This document defines additional OPTIONAL end user, operator, and administrator operations used to control Jobs and Printers. In addition, this document extends the semantic model of the Printer object by allowing them to be configured into trees and/or inverted trees that represent Printer object Fan-Out and Printer object Fan- In, respectively. The special case of a tree with only a single Subordinate node represents Chained Printers. This document is a registration proposal for an extension to IPP/1.0 and IPP/1.1 following the registration procedures in those documents. The requirements and use cases for this document are defined in [RFC3239].2. Terminology This section defines the terminology used throughout this document.2.1. Conformance Terminology Capitalized terms such as MUST, MUST NOT, REQUIRED, SHOULD, SHOULD NOT, MAY, NEED NOT, and OPTIONAL have special meaning relating to conformance as defined inRFC 2119 [RFC2119] and [RFC2911],section12.1. If an implementation supports the extension defined in this document, then these terms apply; otherwise, they do not. These terms define conformance to this document only; they do not affect conformance to other documents, unless explicitly stated otherwise.Kugler, et al. Standards Track [Page 4]
RFC 3998 IPP: Job and Printer Operations March 20052.2. Other Terminology This document uses terms such as "client", "Printer", "Job", "attributes", "keywords", "operation", and "support". These terms have special meaning and are defined in the model terminology ([RFC2911], section 12.2). In addition, the following capitalized terms are defined: IPP Printer object (or Printer for short) - A software abstraction defined by [RFC2911]. Printer Operation - An operation whose target is an IPP Printer object and whose effect is on the Printer object. Output Device - The physical imaging mechanism that an IPP Printer controls. Note: although this term is capitalized in this specification (but not in [RFC2911]), there is no formal object called an Output Device defined in this document (or in [RFC2911]). Output Device Fan-Out - A configuration in which an IPP Printer controls more than one Output Device. Printer Fan-Out - A configuration in which an IPP Printer object controls more than one Subordinate IPP Printer object. Printer Fan-In - A configuration in which an IPP Printer object is controlled by more than one IPP Printer object. Subordinate Printer - An IPP Printer object that is controlled by another IPP Printer object. Such a Subordinate Printer MAY have zero or more Subordinate Printers. Leaf Printer - An IPP Printer object that has no Subordinate Printers. Non-Leaf Printer - An IPP Printer object that has one or more Subordinate Printers. A Non-Leaf Printer is also called a Parent Printer. Chained Printer - a Non-Leaf Printer that has exactly one Subordinate Printer. Job Creation operations - IPP operations that create a Job object: Print-Job, Print-URI, and Create-Job.Kugler, et al. Standards Track [Page 5]
RFC 3998 IPP: Job and Printer Operations March 20053. Definition of the Printer Operations All Printer Operations are directed at Printer objects. A client MUST always supply the "printer-uri" operation attribute in order to identify the correct target of the operation. These descriptions assume all of the common semantics of the IPP/1.1 Model and Semantics document ([RFC2911], section 3.1). The Printer Operations defined in this document are summarized in Table 1. Table 1. Printer Operation Operation-Id Assignments Operation Name Operation-Id Brief Description -------------------------------------------------------------------- Enable-Printer 0x22 Allows the target Printer to accept Job Creation operations. Disable-Printer 0x23 Prevents the target Printer from accepting Job Creation operations. Pause-Printer- 0x24 Pauses the Printer after the current After-Current- job has been sent to the Output Job Device. Hold-New-Jobs 0x25 Finishes processing all currently pending jobs. Any new jobs are placed in the 'pending-held' state. Release-Held- 0x26 Releases all jobs to the 'pending' New-Jobs state that had been held by the effect of a previous Hold-New-Jobs operation and condition the Printer so that it no longer holds new jobs. Deactivate- 0x27 Puts the Printer into a read-only Printer deactivated state. Activate- 0x28 Restores the Printer to normal Printer activity. Restart-Printer 0x29 Restarts the target Printer and re- initializes the software. Shutdown- 0x2A Shuts down the target Printer so that Printer it cannot be restarted or queried.Kugler, et al. Standards Track [Page 6]
RFC 3998 IPP: Job and Printer Operations March 2005 Startup-Printer 0x2B Starts up the instance of the Printer object. All of the operations in this document are OPTIONAL for an IPP object to support. Unless the specification of an OPTIONAL operation requires support of another OPTIONAL operation, conforming implementations may support any combination of these operations. Many of the operations come in pairs, so both are REQUIRED if either one is implemented.3.1. The Disable and Enable Printer Operations This section defines the OPTIONAL Disable-Printer and Enable-Printer operations that stop and start the IPP Printer object from accepting new IPP jobs. If either of these operations are supported, both MUST be supported. These operations allow the operator to control whether the Printer will accept new Job Creation (Print-Job, Print-URI, and Create-Job) operations. These operations have no other effect on the Printer, so the Printer continues to accept all other operations and continues to schedule and process jobs normally. In other words, these operations control the "input of new jobs" to the IPP Printer, and the Pause and Resume operations (seesection 3.2) independently control the "output of new jobs" from the IPP Printer to the Output Device.3.1.1. Disable-Printer Operation This OPTIONAL operation allows a client to stop the Printer object from accepting new jobs; i.e., it causes the Printer to reject subsequent Job Creation operations and return the 'server-error-not- accepting-jobs' status code. The Printer still accepts all other operations, including Validate-Job, Send-Document, and Send-URI operations. Thus a Disable-Printer operation allows a client to continue submitting multiple documents of a multiple document job if the Create-Job operation had already been accepted. All previously created or submitted Jobs and all Jobs currently processing continue unaffected. The IPP Printer MUST accept the request in any state. The Printer sets the value of its "printer-is-accepting-jobs" READ-ONLY Printer Description attribute to 'false' (see[RFC2911], section 4.4.20), no matter what the previous value was. This operation has no immediate or direct effect on the Printer's "printer-state" and "printer- state-reasons" attributes.Kugler, et al. Standards Track [Page 7]
RFC 3998 IPP: Job and Printer Operations March 2005 Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911] sections1 and8.5). The Disable-Printer Request and Disable-Printer Response have the same attribute groups and attributes as do the Pause-Printer operation (see [RFC2911], sections3.2.7.1 and3.2.7.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.1.2. Enable-Printer Operation This OPTIONAL operation allows a client to start the Printer object accepting jobs; i.e., it causes the Printer to accept subsequent Job Creation operations. The Printer still accepts all other operations. All previously submitted and currently processing Jobs continue unaffected. The IPP Printer MUST accept the request in any state. The Printer sets the value of its "printer-is-accepting-jobs" READ-ONLY Printer Description attribute to 'true' (see[RFC2911], section 4.4.20), no matter what the previous value was. This operation has no immediate or direct effect on the Printer's "printer-state" and "printer- state-reasons" attributes. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911] sections1 and8.5). The Enable-Printer Request and Enable-Printer Response have the same attribute groups and attributes as does the Pause-Printer operation (see [RFC2911], sections3.2.8.1 and3.2.8.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.2. The Pause and Resume Printer Operations This section leaves the OPTIONAL IPP/1.1 Pause-Printer (see [RFC2911], sections3.2.7) ambiguous as to whether it stops the Printer immediately or after the current job. It also defines the OPTIONAL Pause-Printer-After-Current-Job operation as following the current job. These operations affect the scheduling of IPP jobs. If either of these Pause Printer operations are supported, then the Resume-Printer operation MUST be supported. These operations allow the operator to control whether the Printer will send new IPP jobs to the associated Output Device(s) that the IPP Printer object represents. These operations have no other effect on the Printer, so the Printer continues to accept all operations.Kugler, et al. Standards Track [Page 8]
RFC 3998 IPP: Job and Printer Operations March 2005 In other words, these operations control the "output of new jobs" to the Output Device(s), and the Disable and Enable Printer Operations (seesection 3.1) independently control the "input of new jobs" to the IPP Printer. Table 2. Pause and Resume Printer Operations Pause and Resume Printers Description -------------------------------------------------------------------- IPP/1.1 Pause Printer Stops the IPP Printer from sending new IPP Jobs to the Output Device(s) either immediately or after the current job completes, depending on implementation, as defined in [RFC2911]. Pause-Printer-After- Stops the IPP Printer from sending Current-Job new IPP Jobs to the Output Device(s) after the current jobs finish. Resume-Printer Starts the IPP Printer sending IPP Jobs to the Output Device again.3.2.1. Pause-Printer-After-Current-Job Operation This OPTIONAL operation allows a client to stop the Printer object from sending IPP jobs to any of its Output Devices or Subordinate Printers. If the IPP Printer is in the middle of sending an IPP job to an Output Device or Subordinate Printer, the IPP Printer MUST complete sending that Job. However, after receiving this operation, the IPP Printer MUST NOT send any additional IPP jobs to any of its Output Devices or Subordinate Printers. In addition, after having received this operation, the IPP Printer MUST NOT start processing any more jobs, so additional jobs MUST NOT enter the 'processing' state. If the IPP Printer is not sending an IPP Job to the Output Device or Subordinate Printer (whether or not the Output Device or Subordinate Printer is busy processing any jobs), the IPP Printer object transitions immediately to the 'stopped' state by setting its "printer-state" attribute to 'stopped', removing the 'moving-to- paused' value, if present, from its "printer-state-reasons" attribute, and adding the 'paused' value to its "printer-state- reasons" attribute. If the implementation will take appreciable time to complete sending an IPP job that it has started sending to an Output Device or Subordinate Printer, the IPP Printer adds the 'moving-to-paused'Kugler, et al. Standards Track [Page 9]
RFC 3998 IPP: Job and Printer Operations March 2005 value to the Printer object's "printer-state-reasons" attribute (see section [RFC2911], 4.4.12). When the IPP Printer has completed sending IPP jobs that it was in the process of sending, the Printer object transitions to the 'stopped' state by setting its "printer- state" attribute to 'stopped', removing the 'moving-to-paused' value, if present, from its "printer-state-reasons" attribute, and adding the 'paused' value to its "printer-state-reasons" attribute. This operation MUST NOT affect the acceptance of Job Creation requests (see Disable-Printer Operation,section 3.1.1). For any jobs that are 'pending' or 'pending-held', the 'printer- stopped' values of the jobs' "job-state-reasons" attribute also apply. However, the IPP Printer NEED NOT update those jobs' "job- state-reasons" attributes and only have to return the 'printer- stopped' value when those jobs are queried by using the Get-Job- Attributes or Get-Jobs operations (so-called "lazy evaluation"). The IPP Printer MUST accept the request in any state and transition the Printer to the indicated new "printer-state", and it MUST add the indicated value to "printer-state-reasons" attribute before returning as follows: Table 3. State Transition Table for Pause-Printer-After-Current-Job Operation Current New "printer IPP Printer's response status "printer- "printer- -state- code and action (REQUIRED/ state" state" reasons" OPTIONAL state transition for a Printer to support): -------------------------------------------------------------------- 'idle' 'stopped' 'paused' REQUIRED: 'successful-ok' 'processing' 'processing' 'moving- OPTIONAL: 'successful-ok'; to- Later, when the IPP Printer paused' has finished sending IPP jobs to an Output Device, the "printer-state" becomes 'stopped', and the 'paused' value replaces the 'moving-to- paused' value in the "printer- state-reasons" attribute 'processing' 'stopped' 'paused' REQUIRED: 'successful-ok'; the IPP Printer wasn't in the middle of sending an IPP job to an Output DeviceKugler, et al. Standards Track [Page 10]
RFC 3998 IPP: Job and Printer Operations March 2005 'stopped' 'stopped' 'paused' REQUIRED: 'successful-ok' Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Pause-Printer-After-Current-Job Request and Pause-Printer-After- Current-Job Response have the same attribute groups and attributes as does the Pause-Printer operation (see [RFC2911], sections3.2.7.1 and 3.2.7.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.3. Hold and Release New Jobs Operations This section defines operations to condition the Printer to hold any new jobs and to release them.3.3.1. Hold-New-Jobs Operation This OPTIONAL operation allows a client to condition the Printer to complete the current 'pending' and 'processing' IPP Jobs but not to start processing any subsequently created IPP Jobs. If the IPP Printer is in the middle of sending an IPP job to an Output Device or Subordinate Printer, the IPP Printer MUST complete sending that Job. Furthermore, the IPP Printer MUST send all of the current 'pending' IPP Jobs to the Output Device(s) or Subordinate IPP Printer object(s). Any subsequently received Job Creation operations will cause the IPP Printer to put the Job into the 'pending-held' state, with the 'job-held-on-create' value being added to the job's "job- state-reasons" attribute. Thus all newly accepted jobs will be automatically held by the Printer. When the Printer completes all the 'pending' and 'processing' jobs, it enters the 'idle' state as usual. An operator monitoring Printer state changes will know when the Printer has completed all current jobs because the Printer enters the 'idle' state. This operation MUST NOT affect the acceptance of Job Creation requests (see Disable-Printer Operation,section 3.1.1), except to put the Jobs into the 'pending-held' state, instead of the 'pending' or 'processing' state. The IPP Printer MUST accept the request in any state, MUST NOT transition the Printer to any other "printer-state", and MUST add the 'hold-new-jobs' value to the Printer's "printer-state-reasons" attribute (whether the value was present or not).Kugler, et al. Standards Track [Page 11]
RFC 3998 IPP: Job and Printer Operations March 2005 Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Hold-New-Jobs Request and Hold-New-Jobs Response have the same attribute groups and attributes as does the Pause-Printer operation (see [RFC2911], sections3.2.7.1 and3.2.7.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.3.2. Release-Held-New-Jobs Operation This OPTIONAL operation allows a client to undo the effect of a previous Hold-New-Jobs operation. In particular, the Printer releases all the jobs that it held as a consequence of a Hold-New- Jobs operations; i.e., while the 'hold-new-jobs' value was present in the Printer's "printer-state-reasons" attribute. In addition, the Printer MUST accept this request in any state, MUST NOT transition the Printer to any other "printer-state", and MUST remove the 'hold- new-jobs' value from its "printer-state-reasons" attribute (whether the value was present or not) so that the Printer no longer holds newly created jobs. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Release-Held-New-Jobs Request and Release-Held-New-Jobs Response have the same attribute groups and attributes as the Pause-Printer operation (see [RFC2911], sections3.2.7.1 and3.2.7.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.4. Deactivate and Activate Printer Operations This section defines the OPTIONAL Deactivate-Printer and Activate- Printer operations that stop and start the IPP Printer object from accepting all requests except queries and performing work. If either of these operations are supported, both MUST be supported. These operations allow the operator to put the Printer into a dormant read-only condition and to take it out of this condition.Kugler, et al. Standards Track [Page 12]
RFC 3998 IPP: Job and Printer Operations March 20053.4.1. Deactivate-Printer Operation This OPTIONAL operation allows a client to stop the Printer object from sending IPP jobs to any of its Output Devices or Subordinate Printers (Pause-Printer-After-Current-Job) and to stop the Printer object from accepting any requests but query requests. The Printer performs a Disable-Printer and a Pause-Printer-After-Current-Job operation immediately. If these two operations cannot be completed immediately, it includes use of all of the "printer-state-reasons". In addition, the Printer MUST immediately reject all requests, except for Activate-Printer, queries (Get-Printer-Attributes, Get-Job- Attributes, Get-Jobs, etc.), Send-Document, and Send-URI (so that partial job submission can be completed, seesection 3.1.1). The Printer MUST then return the 'server-error-service-unavailable' status code. The IPP Printer MUST accept the request in any state. Immediately, the Printer MUST set the 'deactivated' value in its "printer-state- reasons" attribute. Note: neither the Disable-Printer nor the Pause-Printer-After-Current-Job set the 'deactivated' value. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Deactivate-Printer Request and Deactivate-Printer Response have the same attribute groups and attributes as does the Pause-Printer operation (see [RFC2911], sections3.2.7.1 and3.2.7.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.4.2. Activate-Printer Operation This OPTIONAL operation allows a client to undo the effects of the Deactivate-Printer; i.e., it allows the Printer object to start sending IPP jobs to any of its Output Devices or Subordinate Printers (Pause-Printer-After-Current-Job) and starts the Printer object from accepting any requests. The Printer performs an Enable-Printer and a Resume-Printer operation immediately. In addition, the Printer MUST immediately start accepting all requests. The IPP Printer MUST accept the request in any state. The Printer MUST immediately remove the 'deactivated' value from its "printer- state-reasons" attribute (whether it is present or not). Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5).Kugler, et al. Standards Track [Page 13]
RFC 3998 IPP: Job and Printer Operations March 2005 The Activate-Printer Request and Activate-Printer Response have the same attribute groups and attributes as the Pause-Printer operation (see [RFC2911], sections3.2.7.1 and3.2.7.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.5. Restart-Printer, Shutdown-Printer, and Startup-Printer Operations This section defines the OPTIONAL Restart-Printer, Shutdown-Printer, and Startup-Printer operations that initialize, shutdown, and start up the Printer object, respectively. Each of these operations is OPTIONAL, and any combination MAY be supported.3.5.1. Restart-Printer Operation This OPTIONAL operation allows a client to restart a Printer object whose operation is in need of initialization because of incorrect or erratic behavior; i.e., perform the effect of a software re-boot. The implementation MUST attempt to save any information about Jobs and the Printer object before re-initializing. However, this operation MAY have drastic consequences on the running system, so the client SHOULD first try the Deactivate-Printer operation to minimize the effect on the current state of the system. The effects of previous Disable-Printer, Pause Printer, and Deactivate-Printer operations are lost. The IPP Printer MUST accept the request in any state. The Printer object MUST initialize its Printer's "printer-state" to 'idle', remove the state reasons from its "printer-state-reasons" attribute, and change its "printer-is-accepting-jobs" attribute to 'true'. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Restart-Printer Request and Restart-Printer Response have the same attribute groups and attributes as does the Pause-Printer operation (see [RFC2911], sections3.2.8.1 and3.2.8.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.5.2. Shutdown-Printer Operation This OPTIONAL operation allows a client to shutdown a Printer; i.e., to stop processing jobs without losing any jobs and to make the Printer object unavailable for any operations using the IPP protocol. There is no way to bring the instance of the Printer object back to being used, except for the Startup-Printer (seesection 3.5.3), which starts up a new instance of the Printer object for hostedKugler, et al. Standards Track [Page 14]
RFC 3998 IPP: Job and Printer Operations March 2005 implementations. The purpose of Shutdown-Printer is to shutdown the Printer for an extended period, not to reset the device(s) or modify a Printer attribute. See Restart-Printer (section 3.5.1) and Startup-Printer (section 3.5.3) for the way to initialize the software. See the Disable-Printer operation (section 3.1) for a way for the client to stop the Printer from accepting Job Creation requests without stopping processing or shutting down. The Printer MUST add the 'shutdown' value (see [RFC2911],section4.4.11) immediately to its "printer-state-reasons" Printer Description attribute. It then performs a Deactivate-Printer operation (seesection 3.4.1), which in turn performs Disable-Printer and Pause-Printer-After-Current-Job operations). Note: To shutdown the Printer after all the currently submitted jobs have completed, the operator issues a Disable-Printer operation (seesection 3.1.1) and then waits until all the jobs have completed. The Printer goes into the 'idle' state before issuing the Shutdown- Printer operation. The Printer object MUST accept this operation in any state and transition the Printer object through the "printer-states" and "printer-state-reasons" defined for the Pause-Printer-After-Current- Job operation until the activity is completed and the Printer object disappears. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Shutdown-Printer Request and Shutdown-Printer Response have the same attribute groups and attributes as does the Pause-Printer operation (see [RFC2911], sections3.2.7.1 and3.2.7.2), including the new "printer-message-from-operator" operation attribute (seesection 6).3.5.3. Startup-Printer operation This OPTIONAL operation allows a client to start up an instance of a Printer object, provided that there isn't one already initiated. The purpose of Startup-Printer is to allow a hosted implementation of the IPP Printer object (i.e., a Server that implements an IPP Printer on behalf of a networked or local Output Device) to be started after the host is available (by means outside this document). Seesection3.5.1 for the way to initialize the software or reset the Output Device(s) when the IPP Printer object has already been initiated.Kugler, et al. Standards Track [Page 15]
RFC 3998 IPP: Job and Printer Operations March 2005 The host MUST accept this operation only when the Printer object has not been initiated. If the Printer object already exists, the host must return the 'client-error-not-possible' status code. The result of this operation MUST be with the Printer object's "printer-state" set to 'idle', the state reasons removed from its "printer-state-reasons" attribute, and its "printer-is-accepting- jobs" attribute set to 'false'. Then the operator can reconfigure the Printer before performing an Enable-Printer operation. However, when a Printer is first powered up, it is RECOMMENDED that its "printer-is-accepting-jobs" attribute be set to 'true' in order to achieve easy "out of the box" operation. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Shutdown-Printer Request and Shutdown-Printer Response have the same attribute groups and attributes as does the Pause-Printer operation (see [RFC2911] sections3.2.7.1 and3.2.7.2), including the new "printer-message-from-operator" operation attribute (seesection6).4. Definition of the Job Operations All Job operations are directed at Job objects. A client MUST always supply some means to identify the Job object in order to select the correct target of the operation. That job identification MAY either be a single Job URI or a combination of a Printer URI and a Job ID. The IPP object implementation MUST support both forms of identification for every job. The Job Operations defined in this document are summarized in Table 4. Table 4. Job Operation Operation-Id Assignments Operation Name Operation-Id Brief description -------------------------------------------------------------------- Reprocess-Job 0x2C Creates a copy of a completed target job with a new Job ID and processes it. Cancel-Current- 0x2D Cancels the current job on the target Job Printer or the specified job if it is the current job.Kugler, et al. Standards Track [Page 16]
RFC 3998 IPP: Job and Printer Operations March 2005 Suspend- 0x2E Suspends the current processing job on Current-Job the target Printer or the specified job if it is the current job, allowing other jobs to be processed instead. Resume-Job 0x2F Resumes the suspended target job. Promote-Job 0x30 Promotes the pending target job to be next after the current job(s) complete. Schedule-Job- 0x31 Schedules the target job immediately After after the specified job, all other scheduling factors being equal.4.1. Reprocess-Job Operation This OPTIONAL operation is a create job operation that allows a client to re-process a copy of a job that had been retained in the queue after processing was completed, canceled, or aborted (see[RFC2911], section 4.3.7.2). This operation is the same as the Restart-Job operation (see[RFC2911], section 3.3.7), except that the Printer creates a new job that is a copy of the target job and the target job is unchanged. New values are assigned to the "job-uri" and "job-id" attributes. The new job's Job Description attributes that track job progress, such as "job-impressions-completed", "job- media-sheets-completed", and "job-k-octets-processed", are initialized to 0, as with any create job operation. The target job moves to the Job History after a suitable period, independent of whether one or more Reprocess-Job operations have been performed upon it. If the Set-Job-Attributes operation is supported, then the "job- hold-until" operation attribute MUST be supported with at least the 'indefinite' value, so that a client can modify the new job before it is scheduled for processing by using the Set-Job-Attributes operation. After modifying the job, the client can release the job for processing by using the Release-Job operation specifying the newly assigned "job-uri" or "job-id" for the new job.4.2. Cancel-Current-Job Operation This OPTIONAL operation allows a client to cancel the current job on the target Printer or the specified job if it is the current job on the Printer. See[RFC2911], section 3.3.3, for the semantics of canceling a job. Since a Job might already be marking by the time a Cancel-Current-Job is received, some media sheet pages might print before the job is actually terminated.Kugler, et al. Standards Track [Page 17]
RFC 3998 IPP: Job and Printer Operations March 2005 If the client does not supply a "job-id" operation attribute, the Printer MUST accept the request and cancel the current job if there is a current job in the 'processing' or 'processing-stopped' state; otherwise, it MUST reject the request and return the 'client-error- not-possible' status code. If more than one job is in the 'processing' or 'processing-stopped' state, the one that is marking is canceled, and the others are unaffected. Warning: On a shared printer, there is a race condition. Between the time when a user issues this operation and the time of its acceptance, the current job might change to a different job. If the user or operator is authenticated to cancel the new job, the wrong job is canceled. To prevent this race from canceling the wrong job, the client MAY supply the "job-id" operation attribute, which is checked against the current job's job-id. If the job identified by the "job-id" attribute is not the current job on the Printer (i.e., is not in the 'processing' or 'processing-stopped' state), the Printer MUST reject this operation and return the 'client-error-not- possible' status code. Otherwise, the Printer cancels the specified job. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must either be the job owner (as determined in the Job Creation operation) or an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Cancel-Current-Job Request and Cancel-Current-Job Response have the same attribute groups and attributes as does the Resume-Printer operation (see[RFC2911], section 3.2.8), including the new "job- message-from-operator" operation attribute (seesection 6), with the addition of the following Group 1 Operation attribute in the request: "job-id" (integer(1:MAX)): The client OPTIONALLY supplies this Operation attribute to verify that the identified job is still the current job on the target Printer object. The IPP object MUST support this operation attribute if it supports this operation.4.3. Suspend and Resume Job Operations This section defines the Suspend-Current-Job and Resume-Job operations. These operations allow an operator or user to suspend a job while it is processing, allowing other jobs to be processed, and to resume the suspended job at a later point without losing any of the output.Kugler, et al. Standards Track [Page 18]
RFC 3998 IPP: Job and Printer Operations March 2005 If either of these operations is supported, both MUST be supported. The Hold-Job and Release-Job operations ([RFC2911], section 3.3.5) are for holding and releasing held jobs, not suspending and resuming suspended jobs.4.3.1. Suspend-Current-Job Operation This OPTIONAL operation allows a client to stop the current job on the target Printer or the specified job if it is the current job on the Printer, to allow other jobs to be processed instead. The Printer moves the current job or the target job to the 'processing- stopped' state and sets the 'job-suspended' value (seesection 9.1) in the job's "job-state-reasons" attribute and processes other jobs. If the client does not supply a "job-id" operation attribute, the Printer MUST accept the request and suspend the current job if there is a current job in the 'processing' or 'processing-stopped' state. Otherwise, it MUST reject the request and return the 'client-error- not-possible' status code. If more than one job is in the 'processing' or 'processing-stopped' state, all of them are suspended. Warning: On a shared printer, there is a race condition. Between the time when a user issues this operation and the time of its acceptance, the current job might change to a different job. If the user or operator is authenticated to suspend the new job, the wrong job is suspended. To prevent this race from pausing the wrong job, the client MAY supply the "job-id" operation attribute, which is checked against the current job's job-id. If the job identified by the "job-id" attribute is not the current job on the Printer (i.e., is not in the 'processing' or 'processing-stopped' state), the Printer MUST reject this operation and return the 'client-error-not- possible' status code. Otherwise, the Printer suspends the specified job and processed other jobs. The Printer MUST reject a Suspend-Current-Job request (and return the 'client-error-not-possible') for a job that has been suspended, i.e., for a job in the 'processing-stopped' state, with the 'job-suspended' value in its "job-state-reasons" attribute. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be either the job owner (as determined in the Job Creation operation) or an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5).Kugler, et al. Standards Track [Page 19]
RFC 3998 IPP: Job and Printer Operations March 2005 The Suspend-Current-Job Request and Suspend-Current-Job Response have the same attribute groups and attributes as does the Pause-Printer operation (see[RFC2911], section 3.2.8 ), including the new "job- message-from-operator" operation attribute (seesection 6), with the addition of the following Group 1 Operation attribute in the request: "job-id" (integer(1:MAX)): The client OPTIONALLY supplies this Operation attribute to verify that the identified job is still the current job on the target Printer object. The IPP object MUST support this operation attribute if it supports this operation.4.3.2. Resume-Job Operation This OPTIONAL operation allows a client to resume the target job at the point where it was suspended. The Printer moves the target job to the 'pending' state and removes the 'job-suspended' value from the job's "job-state-reasons" attribute. If the target job is not in the 'processing-stopped' state, with the 'job-suspended' value in the job's "job-state-reasons" attribute, the Printer MUST reject the request and return the 'client-error-not- possible' status code, since the job was not suspended. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be either the job owner (as determined in the Job Creation operation) or an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Resume-Job Request and Resume-Job Response have the same attribute groups and attributes as the Release-Job operation (see[RFC2911], section 3.3.6), including the new "job-message-from- operator" operation attribute (seesection 6).4.4. Job Scheduling Operations This section defines jobs that allow an operator to control the scheduling of jobs.4.4.1. Promote-Job Operation This OPTIONAL operation allows a client to make the pending target job be processed next after the current job completes. This operation is especially useful in a production printing environment where the operator is involved in job scheduling.Kugler, et al. Standards Track [Page 20]
RFC 3998 IPP: Job and Printer Operations March 2005 If the target job is in the 'pending' state, this operation does not change the job's state but causes the job to be processed after the current job(s) complete. If the target job is not in the 'pending' state, the Printer MUST reject the request and return the 'client- error-not-possible' status code. If the Printer implements the "job-priority" Job Template attribute (see[RFC2911], section 4.2.1), the Printer sets the job's "job- priority" to the highest value supported (so that the job will print before any of the other pending jobs). The Printer returns the target job immediately after the current job(s) in a Get-Jobs response (see[RFC2911], section 3.2.6) for the 'not-completed' jobs. When the current job is completed, canceled, suspended (seesection4.3.1), or aborted, the target of this operation is processed next. If a client issues this request (again) before the target of the operation of the original request started processing, the target of this new request is processed first. IPP is specified not to require queues for job scheduling, as there are other implementation techniques for scheduling multiple jobs, such as re-evaluating a criteria function for each job on a scheduling cycle. However, if an implementation does implement queues for jobs, then the Promote-Job operation puts the specified job at the front of the queue. A subsequent Promote-Job operation prior to the processing of the first job puts that specified job at the front of the queue, so that it is "in front" of the previously promoted job. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5). The Promote-Job Request and Promote-Job Response have the same attribute groups and attributes as does the Cancel-Job operation (see[RFC2911], section 3.3.3), including the new "job-message-from- operator" operation attribute (seesection 6).4.4.2. Schedule-Job-After Operation This OPTIONAL operation allows a client to request that the Printer schedule the target job so that it will be processed immediately after the specified predecessor job, all other scheduling factors being equal. This operation is specially useful in a production printing environment where the operator is involved in job scheduling.Kugler, et al. Standards Track [Page 21]
RFC 3998 IPP: Job and Printer Operations March 2005 If the target job is in the 'pending' state, this operation does not change the job's state but causes the job to be processed after the preceding job completes. The preceding job can be in the target 'pending', 'processing', or 'processing-stopped' state. If the target job is not in the 'pending' state, or if the predecessor job is not in the 'pending', 'processing', or 'processing-stopped' state, the Printer MUST reject the request, and it returns the 'client- error-not-possible' status code, as the job cannot have its position changed. If the Printer implements the "job-priority" Job Template attribute (see[RFC2911], section 4.2.1), the Printer sets the job's "job- priority" to that of the predecessor job (so that the job will print after the predecessor job). The Printer returns the target job immediately after the predecessor in a Get-Jobs response (see[RFC2911], section 3.2.6) for the 'not-completed' jobs. When the predecessor job completes processing or is canceled or aborted while processing, the target of this operation is processed next. If the client does not supply a predecessor job, this operation has the same semantics as Promote-Job (seesection 4.4). IPP is specified not to require queues for job scheduling, as there are other implementation techniques for scheduling multiple jobs, such as re-evaluating a criteria function for each job on a scheduling cycle. However, if an implementation does implement queues for jobs, then the Schedule-Job-After operation puts the specified job immediately after the specified job in the queue. A subsequent Schedule-Job-After operation specifying the same job will cause its target job to be placed after that job, even though it is between the first target job and the specified job. For example, suppose the job queue consisted of jobs A, B, C, D, and E, in that order. A Schedule-Job-After with job E as the target and B as the specified job would result in the following queue: A, B, E, C, D. A subsequent Schedule-Job-After with Job D as the target and B as the specified job would result in the following queue: A, B, D, E, C. In other words, the link between the two jobs in a Schedule-Job-After operation is not retained; i.e., there is no attribute on either job that points to the other job as a result of this operation. Access Rights: The authenticated user (see[RFC2911], section 8.3) performing this operation must be an operator or administrator of the Printer object (see [RFC2911], sections1 and8.5).Kugler, et al. Standards Track [Page 22]
RFC 3998 IPP: Job and Printer Operations March 2005 The Schedule-Job-After Request have the same attribute groups and attributes as does the Cancel-Job operation (see [RFC2911],section3.3.3), plus the new "job-message-from-operator" operation attribute (seesection 6). In addition, the following operation attribute is defined: "predecessor-job-id": The client OPTIONALLY supplies this attribute. The Printer MUST support it, if it supports this operation. This attribute specifies the job after which the target job is to be processed. If the client omits this attribute, the Printer MUST process the target job next, i.e., after the current job, if there is one. The Schedule-Job-After Response has the same attribute groups, attributes, and status codes as does the Cancel-Job operation (see[RFC2911], section 3.3.3). The following status codes have particular meaning for this operation: 'client-error-not-possible' - The target job was not in the 'pending' state, or the predecessor job was not in the 'pending', 'processing', or 'processing-stopped' state. 'client-error-not-found' - Either the target job or the predecessor job was not found.5. Additional Status Codes This section defines new status codes used by the operations defined in this document.5.1. 'server-error-printer-is-deactivated' (0x050A) The Printer has been deactivated by the Deactivate-Printer operation and is only accepting the Activate-Printer (seesection 3.5.1), Get- Job-Attributes, Get-Jobs, Get-Printer-Attributes, and any other Get- Xxxx operations. An operator can perform the Activate-Printer operation to allow the Printer to accept other operations.6. Use of Operation Attributes That Are Messages from the Operator This section summarizes the usage of the "printer-message-from- operator" and "job-message-from-operator" operation attributes [RFC3380] that set the corresponding Printer and Job Description attributes (see [RFC2911] for the definition of these). These operation attributes are defined for most of the Printer and Job operations that operators are likely to perform, respectively, so that operators can indicate the reasons for their actions.Kugler, et al. Standards Track [Page 23]
RFC 3998 IPP: Job and Printer Operations March 2005 Table 5 shows the operation attributes defined for use with the Printer Operations. Table 5. Operation Attribute Support for Printer Operations Operation Attribute A B --------------------------------------------- attributes-charset REQ REQ attributes-natural-language REQ REQ printer-uri REQ REQ requesting-user-name REQ REQ printer-message-from-operator Note OPT Legend: A: Get-Printer-Attributes, Set-Printer-Attributes B: All other Printer administrative operations, including, but not limited to, Pause-Printer, Pause-Printer-After-Current- Job, Resume-Printer, Hold-New-Jobs, Release-Held-New-Jobs, Purge-Jobs, Enable-Print, Disable-Printer, Restart- Printer, Shutdown-Printer, and Startup-Printer. REQ: REQUIRED for a Printer to support. OPT: OPTIONAL for a Printer to support; the Printer ignores the attribute if it is not supported. Note: According to [RFC3380], the Client MUST NOT supply the "printer-message-from-operator" operation attribute in a Get-Printer-Attributes or Set-Printer-Attributes operation; the Printer MUST ignore this operation attribute in these two operations. Instead, when it is used by an operator, the client MUST supply the "printer-message-from-operator" as (one of the) explicit attributes being set on the Printer object with the Set-Printer-Attributes operation.Kugler, et al. Standards Track [Page 24]
RFC 3998 IPP: Job and Printer Operations March 2005 Table 6 shows the operation attributes defined for use with the Job operations. Table 6. Operation Attribute Support for Job Operations Operation Attribute A B C F --------------------------------------------------------- attributes-charset REQ REQ REQ REQ attributes-natural-language REQ REQ REQ REQ printer-uri REQ REQ REQ REQ job-uri REQ REQ REQ job-id REQ REQ REQ REQ requesting-user-name REQ REQ REQ REQ job-message-from-operator OPT OPT OPT Note message** OPT OPT OPT n/a job-hold-until n/a n/a OPT* n/a Legend: A: Cancel-Job, Resume-Job, Restart-Job, Promote-Job, Schedule-Job- After B: Cancel-Current-Job, Suspend-Current-Job C: Hold-Job, Release-Job, Reprocess-Job F: Get-Job-Attributes, Set-Job-Attributes REQ; REQUIRED for a Printer to support. OPT: OPTIONAL for a Printer to support; the Printer ignores the attribute if it is supplied, but not supported. n/a: not applicable for use with the operation; the Printer ignores the attribute. Note: According to [RFC3380], the Client MUST NOT supply the "job- message-from-operator" operation attribute in a Get-Job- Attributes or Set-Job-Attributes operation; the Printer MUST ignore this operation attribute in these two operations. Instead, when used by an operator, the client MUST supply the "job-message-from-operator" as (one of the) explicit attributes being set on the Job object with the Set-Job-Attributes operation. *: The Printer MUST support the "job-hold-until" operation attribute if it supports the "job-hold-until" Job Template attribute. For the Reprocess-Job operation, the client can hold the job and then modify the job before releasing it to be processed. **: In [RFC2911], the "message" operation attribute is defined to contain a message to the operator, but [RFC2911] does not define a Job Description attribute to store the message.Kugler, et al. Standards Track [Page 25]
RFC 3998 IPP: Job and Printer Operations March 20057. New Printer Description Attributes The following new Printer Description attributes are needed to support the new operations defined in this document and the concepts of Printer Fan-Out (seesection 10).7.1. subordinate-printers-supported (1setOf uri) This Printer attribute is REQUIRED if an implementation supports Subordinate Printers (seesection 10) and contains the URIs of the immediate Subordinate Printer object(s) associated with this Printer object. Each Non-Leaf Printer object MUST support this Printer Description attribute. A Leaf Printer object either does not support the "subordinate-printers-supported" attribute or does so with the 'no-value' out-of-band value (see[RFC2911], section 4.1), depending on the implementation. The precise format of the Subordinate Printer URIs is implementation dependent (seesection 10.4). If the Printer object does not have an associated Output Device, the Printer MAY automatically copy the value of the Subordinate Printer object's "printer-name" attribute to the Job object's "output- device-assigned" attribute (see[RFC2911], section 4.3.13). The "output-device-assigned" Job attribute identifies the Output Device to which the Printer object has assigned a job; for example, when a single Printer object is supporting Device Fan-Out or Printer Fan- Out.7.2. parent-printers-supported (1setOf uri) This Printer attribute is REQUIRED if an implementation supports Subordinate Printers (seesection 10) and contains the URI of the Non-Leaf printer object(s) for which this Printer object is the immediate Subordinate; i.e., this Printer's immediate "parent" or "parents". Each Subordinate Printer object MUST support this Printer Description attribute. A Printer that has no parents either does not support the "parent-printers-supported" attribute or does so with the 'no-value' out-of-band value (see[RFC2911], section 4.1), depending on the implementation.8. Additional Values for the "printer-state-reasons" Printer Description Attribute This section defines additional values for the "printer-state- reasons" Printer Description attribute.Kugler, et al. Standards Track [Page 26]
RFC 3998 IPP: Job and Printer Operations March 20058.1. 'hold-new-jobs' Value 'hold-new-jobs': The operator has issued the Hold-New-Jobs operation (seesection 3.3.1) or other means, but the output-device(s) are taking an appreciable time to stop. Later, when all output has stopped, the "printer-state" becomes 'stopped', and the 'paused' value replaces the 'moving-to-paused' value in the "printer- state-reasons" attribute. This value MUST be supported if the Hold-New-Jobs operation is supported and the implementation takes significant time to pause a device in certain circumstances.8.2. 'deactivated' Value 'deactivated': A client has issued a Deactivate-Printer operation for the Printer object (seesection 3.4.1), and the Printer is in the process of becoming deactivated or has become deactivated. The Printer MUST reject all requests except for Activate-Printer, queries (Get-Printer-Attributes, Get-Job-Attributes, Get-Jobs, etc.), Send-Document, and Send-URI (so that partial job submission can be completed; seesection 3.1.1), and then return the 'server-error-service-unavailable' status code.9. Additional Values for the "job-state-reasons" Job Description Attribute This section defines additional values for the "job-state-reasons" Job Description attribute.9.1. 'job-suspended' Value 'job-suspended': While job processing has been suspended by the Suspend-Current-Job operation, other jobs can be processed on the Printer. The Job can be resumed with the Resume-Job operation, which removes this value.10. Use of the Printer Object to Represent IPP Printer Fan-Out and IPP Printer Fan-In This section defines how the Printer object MAY be used to represent IPP Printer Fan-Out and IPP Printer Fan-In. In Fan-Out, an IPP Printer is used to represent other IPP Printer objects. In Fan-In, several IPP Printer objects are used to represent another IPP Printer object.Kugler, et al. Standards Track [Page 27]
RFC 3998 IPP: Job and Printer Operations March 200510.1. IPP Printer Fan-Out The IPP/1.1 Model and Semantics introduces the semantic concept of an IPP Printer object that represents more than one Output Device (see[RFC2911], section 2.1). This concept is called "Output Device Fan- Out". However, with Fan-Out there was no way to represent the individual states of the Output Devices or to perform operations on a specific Output Device. This document generalizes the semantics of the Printer object to represent Subordinate Fan-Out Output Devices such as IPP Printer objects. This concept is called "Printer object Fan-Out". A Printer object that has a Subordinate Printer object is called a Non-Leaf Printer object. Thus, a Non-Leaf Printer object supports one or more Subordinate Printer objects in order to represent Printer object Fan-Out. A Printer object that does not have any Subordinate Printer objects is called a Leaf Printer object. Each Non-Leaf Printer object submits jobs to its immediate Subordinate Printers and otherwise controls the Subordinate Printers by using IPP or other protocols. Whether pending jobs are kept in the Non-Leaf Printer until a Subordinate Printer can accept them or are kept in the Subordinate Printers depends on implementation and/or configuration policy. Furthermore, a Subordinate Printer object MAY, in turn, have Subordinate Printer objects. Thus a Printer object can be both a Non-Leaf Printer and a Subordinate Printer. A Subordinate Printer object MUST be a conforming Printer object, so it MUST support all of the REQUIRED [RFC2911] operations and attributes. However, with access control, the Subordinate Printer MAY be configured so that end-user clients are not permitted to perform any operations (or just Get-Printer-Attributes) while one or more Non-Leaf Printer object(s) are permitted to perform any operation.10.2. IPP Printer Fan-In The IPP/1.1 Model and Semantics did not preclude the semantic concept of multiple IPP Printer objects that represent a single Output Device (see[RFC2911], section 2.1). However, there was no way for the client to determine whether there was a Fan-In configuration; nor was there a way to perform operations on the Subordinate device. This specification generalizes the semantics of the Printer object to allow several Non-Leaf IPP Printer objects to represent a single Subordinate Printer object. Thus a Non-Leaf Printer object MAY share a Subordinate Printer object with one or more other Non-Leaf Printer objects in order to represent IPP Printer Fan-In. As with Fan-Out (seesection 10.1), when a Printer object is a Non- Leaf Printer, it MUST NOT have an associated Output Device. As withKugler, et al. Standards Track [Page 28]
RFC 3998 IPP: Job and Printer Operations March 2005 Fan-Out, a Leaf Printer object has one or more associated Output Devices. As with Fan-Out, the Non-Leaf Printer objects submit jobs to their Subordinate Printer objects and otherwise control the Subordinate Printer. As with Fan-Out, whether pending jobs are kept in the Non-Leaf Printers until the Subordinate Printer can accept them or are kept in the Subordinate Printer depends on the implementation and/or configuration policy.10.3. Printer Object Attributes Used to Represent Printer Fan-Out and Printer Fan-In The following Printer Description attributes are defined to represent the relationship between Printer object(s) and their Subordinate Printer object(s): 1. "subordinate-printers-supported" (1setOf uri) - Contains the URI of the immediate Subordinate Printer object(s). 2. "parent-printers-supported (1setOf uri) - Contains the URI of the Non-Leaf printer object(s) for which this Printer object is the immediate Subordinate; i.e., this Printer's immediate "parent" or "parents".10.4. Subordinate Printer URI Each Subordinate Printer object has a URI used as the target of each operation on the Subordinate Printer. The means to configure URIs for Subordinate Printer objects is implementation-dependent, as are all URIs. However, there are two distinct approaches: a. When the implementation seeks to make sure that no operation on a Subordinate Printer object "sneaks by" the parent Printer object (or that no Subordinate Printer is fronting for a device that is not networked), the host part of the URI specifies the host of the parent Printer. Then the parent Printer object can easily reflect the state of the Subordinate Printer objects in the parent's Printer object state and state reasons as the operation passes "through" the parent Printer object. b. When the Subordinate Printer is networked and the implementation allows operations to go directly to the Subordinate Printer (with proper access control) without knowledge of the parent Printer object, the host part of the URI is different from the host part of the parent Printer object. In this a case, the parent Printer object MAY keep its "printer-state" and "printer-state-reasons" up to date, either by polling the Subordinate Printer object or by subscribing to events with the Subordinate Printer object (see [RFC3995] forKugler, et al. Standards Track [Page 29]
RFC 3998 IPP: Job and Printer Operations March 2005 means to subscribe to event notification when the Subordinate Printer object supports IPP notification). Alternatively, the parent Printer MAY wait until its "printer-state" and "printer-state-reasons" attributes are queried and then query all its Subordinate Printers in order to return the correct values.10.5. Printer Object Attributes Used to Represent Output Device Fan-Out Only Leaf IPP Printer objects are allowed to have one or more associated Output Devices. Each Leaf Printer object MAY support the "output-devices-supported" (1setOf name(127)) to indicate the user- friendly name(s) of the Output Device(s) that the Leaf Printer object represents. It is RECOMMENDED that each Leaf Printer object have only one associated Output Device, so that the individual Output Devices can be represented completely and controlled completely by clients. In other words, the Leaf Printer's "output-devices- supported" attribute SHOULD have only one value. Non-Leaf Printer MUST NOT have associated Output Devices. However, a Non-Leaf Printer SHOULD support an "output-devices-supported" (1setOf name(127)) Printer Description attribute that contains all the values of its immediate Subordinate Printers. As these Subordinate Printers MAY be Leaf or Non-Leaf, the same rules apply to them. Thus any Non-Leaf Printer SHOULD have an "output-devices-supported" (1setOf name(127)) attribute that contains all the values of the Output Devices associated with Leaf Printers of its complete sub-tree. When a configuration of Printers and Output Devices is added, moved, or changed, there can be moments when the tree structure is not consistent; i.e., times when a Non-Leaf Printer's "subordinate- printers-supported" does not agree with the Subordinate Printer's "parent-printers-supported". Therefore, the operator SHOULD first Deactivate all Printers being configured in this way, update all pointer attributes, and then reactivate them. A useful client tool would validate a tree structure before Activating the Printers involved.10.6. Figures to Show All Possible Configurations Figures 1, 2, and 3 are taken from [RFC2911] to show the configurations possible with IPP/1.0 and IPP/1.1 where all Printer objects are Leaf Printer objects. The remaining figures show additional configurations using Non-Leaf and Leaf Printer objects.Kugler, et al. Standards Track [Page 30]
RFC 3998 IPP: Job and Printer Operations March 2005 Legend: ----> indicates a network protocol with the direction of its requests ##### indicates a Printer object that is either embedded in an Output Device, or hosted in a server. The Printer object might or might not be capable of queuing/spooling. any indicates any network protocol or direct connect, including IPP. Output Device +---------------+ | ########### | O +--------+ | # (Leaf) # | /|\ | client |------------IPP-----------------># Printer # | / \ +--------+ | # Object # | | ########### | +---------------+ Figure 1. Embedded Printer Object ########### Output Device O +--------+ # (Leaf) # +---------------+ /|\ | client |---IPP----># Printer #---any->| | / \ +--------+ # object # | | ########### +---------------+ Figure 2. Hosted Printer Object +---------------+ | | +->| Output Device | ########### any/ | | O +--------+ # (Leaf) # / +---------------+ /|\ | client |---IPP----># Printer #--* / \ +--------+ # Object # \ +---------------+ ########### any\ | | +->| Output Device | | | +---------------+ Figure 3. Output Device Fan-OutKugler, et al. Standards Track [Page 31]
RFC 3998 IPP: Job and Printer Operations March 2005 ########### ########### O +--------+ # Non-Leaf# # subord. # /|\ | client |---IPP----># Printer #---IPP----># Printer # / \ +--------+ # object # # object # ########### ########### The Subordinate Printer can be a Non-Leaf Printer, as in Figures 4 through 6, or can be a Leaf Printer, as in Figures 1 through 3. Figure 4. Chained IPP Printer Objects +------IPP--------------------->########### / +---># subord. # / / # Printer # / ########### IPP # object # O +--------+ # Non-Leaf# / ########### /|\ | client |---IPP----># Printer #--* / \ +--------+ # object # \ \ ########### IPP ########### \ \ # subord. # \ +---># Printer # +------IPP---------------------># object # ########### The Subordinate Printer can be a Non-Leaf Printer, as in Figures 4 through 6, or can be a Leaf Printer, as in Figures 1 through 3. Figure 5. IPP Printer Object Fan-OutKugler, et al. Standards Track [Page 32]
RFC 3998 IPP: Job and Printer Operations March 2005 ########### # Non-Leaf# +---># Printer #-+ / # object # \ IPP ########### \ ########### O +--------+ / +-IPP-># subord. # /|\ | client |--+-----------IPP---------------># Printer # / \ +--------+ \ +-IPP-># object # IPP ########### / ########### \ # Non-Leaf# / +---># Printer #-+ # object # ########### The Subordinate Printer can be a Non-Leaf Printer, as in Figures 4 through 6, or can be a Leaf Printer, as in Figures 1 through 3. Figure 6. IPP Printer Object Fan-In10.7. Forwarding Requests This section describes the forwarding of Job and Printer requests to Subordinate Printer objects.10.7.1. Forwarding Requests that Affect Printer Objects In Printer Fan-Out, Printer Fan-In, and Chained Printers, the Non- Leaf IPP Printer object MUST NOT forward the operations that affect Printer objects to its Subordinate Printer objects. If a client seeks to explicitly target a Subordinate Printer, the client MUST specify the URI of the Subordinate Printer. The client can determine the URI of any Subordinate Printers by querying the Printer's "subordinate-printers-supported (1setOf uri) attribute (seesection7.1). Table 7 lists the operations that affect Printer objects and the forwarding behavior that a Non-Leaf Printer MUST exhibit to its immediate Subordinate Printers. Operations that affect jobs have a different forwarding rule (seesection 10.7.2 and Table 8):Kugler, et al. Standards Track [Page 33]
RFC 3998 IPP: Job and Printer Operations March 2005 Table 7. Forwarding Operations that Affect Printer Objects Printer Operation Non-Leaf Printer Action --------------------------------------------------------------- Printer Operations: Enable-Printer MUST NOT forward to any of its Subordinate Printers Disable-Printer MUST NOT forward to any of its Subordinate Printers Hold-New-Jobs MUST NOT forward to any of its Subordinate Printers Release-Held-New- MUST NOT forward to any of its Subordinate Jobs Printers Deactivate-Printer MUST NOT forward to any of its Subordinate Printers Activate-Printer MUST NOT forward to any of its Subordinate Printers Restart-Printer MUST NOT forward to any of its Subordinate Printers Shutdown-Printer MUST NOT forward to any of its Subordinate Printers Startup-Printer MUST NOT forward to any of its Subordinate Printers IPP/1.1 Printer See [RFC2911] Operations: Get-Printer- MUST NOT forward to any of its Subordinate Attributes Printers Pause-Printer MUST NOT forward to any of its Subordinate Printers Resume-Printer MUST NOT forward to any of its Subordinate Printers Set Operations: See [RFC3380] Set-Printer- MUST NOT forward to any of its Subordinate Attributes PrintersKugler, et al. Standards Track [Page 34]
RFC 3998 IPP: Job and Printer Operations March 200510.7.2. Forwarding Requests that Affect Jobs Unlike Printer Operations that only affect Printer objects (seesection 10.7.1), a Non-Leaf Printer object MUST forward operations that directly affect jobs to the appropriate Job object(s) in one or more of its immediate Subordinate Printer objects. Forwarding is REQUIRED since the purpose of this Job operation is to affect the indicated job, which may have been forwarded itself. This forwarding MAY be immediate or queued, depending on the operation and the implementation. For example, a Non-Leaf Printer object MAY queue/spool jobs, feeding a job at a time to its Subordinate Printer(s), or MAY forward jobs immediately to one of its Subordinate Printers. In either case, the Non-Leaf Printer object forwards Job Creation operations to one of its Subordinate Printers. Only the time of forwarding of the Job Creation operations depends on whether the policy is to queue/spool jobs in the Non-Leaf Printer or the Subordinate Printer. When a Non-Leaf Printer object creates a Job object in its Subordinate Printer, whether that Non-Leaf Printer object keeps a fully formed Job object or just keeps a mapping from the "job-ids" that it assigned to those assigned by its Subordinate Printer object is IMPLEMENTATION-DEPENDENT. In either case, the Non-Leaf Printer MUST be able to accept and carry out future Job operations that specify the "job-id" that the Non-Leaf Printer assigned and returned to the job submitting client. Table 8 lists the operations that directly affect jobs and the forwarding behavior that a Non-Leaf Printer MUST exhibit to its Subordinate Printers.Kugler, et al. Standards Track [Page 35]
RFC 3998 IPP: Job and Printer Operations March 2005 Table 8. Forwarding Operations that Affect Jobs Objects Operation Non-Leaf Printer action --------------------------------------------------------------- Job operations: Reprocess-Job MUST forward to the appropriate Job in one of its Subordinate Printers Cancel-Current- MUST NOT forward Job Resume-Job MUST forward to the appropriate Job in one of its Subordinate Printers Promote-Job MUST forward to the appropriate Job in one of its Subordinate Printers IPP/1.1 Printer operations: Print-Job MUST forward immediately or queue to the appropriate Subordinate Printer Print-URI MUST forward immediately or queue to the appropriate Subordinate Printer Validate-Job MUST forward to the appropriate Subordinate Printer Create-Job MUST forward immediately or queue to the appropriate Subordinate Printer Get-Jobs MUST forward to all its Subordinate Printers Purge-Jobs MUST forward to all its Subordinate Printers IPP/1.1 Job operations: Send-Document MUST forward immediately or queue to the appropriate Job in one of its Subordinate Printers Send-URI MUST forward immediately or queue to the appropriate Job in one of its Subordinate Printers Cancel-Job MUST forward to the appropriate Job in one of its Subordinate Printers Get-Job- MUST forward to the appropriate Job in one of Attributes its Subordinate Printers if the Non-Leaf Printer doesn't know the complete status of the Job object Hold-Job MUST forward to the appropriate Job in one of its Subordinate Printers Release-Job MUST forward to the appropriate Job in one of its Subordinate PrintersKugler, et al. Standards Track [Page 36]
RFC 3998 IPP: Job and Printer Operations March 2005 Restart-Job MUST forward to the appropriate Job in one of its Subordinate Printers IPP Set operations: See [RFC3380] Set-Job- MUST forward to the appropriate Job in one of Attributes its Subordinate Printers When a Printer receives a request that REQUIRES forwarding, it does so on a "best efforts basis" and returns a response to its client without waiting for responses from any of its Subordinate Printers. Such forwarded requests could fail.10.8. Additional Attributes to Help with Fan-Out The following operation and Job Description attributes are defined to help represent Job relationships for Fan-Out and forwarding of jobs.10.8.1. output-device-assigned (name(127)) Job Description Attribute - from [RFC2911] [RFC2911] defines "output-device-assigned" as follows: "This attribute identifies the Output Device to which the Printer object has assigned this job. If an Output Device implements an embedded Printer object, the Printer object NEED NOT set this attribute. If a print server implements a Printer object, the value MAY be empty (zero-length string) or not returned until the Printer object assigns an Output Device to the job. This attribute is particularly useful when a single Printer object supports multiple devices (so called "Device Fan-Out" see[RFC2911] section 2.1)." See alsosection 10.1 in this specification.10.8.2. original-requesting-user-name (name(MAX)) Operation and Job Description Attribute The operation attribute containing the user name of the original user; i.e., corresponding to the "requesting-user-name" operation attribute (see[RFC2911], section 3.2.1.1) that the original client supplied to the first Printer object. The Printer copies the "original-requesting-user-name" operation attribute to the corresponding Job Description attribute.Kugler, et al. Standards Track [Page 37]
RFC 3998 IPP: Job and Printer Operations March 200510.8.3. requesting-user-name (name(MAX)) Operation Attribute - Additional Semantics The IPP/1.1 "requesting-user-name" operation attribute (see[RFC2911] section 3.2.1.1) is updated by each client to be itself on each hop; i.e., the "requesting-user-name" represents the client forwarding the request, not the original client.10.8.4. job-originating-user-name (name(MAX)) Job Description Attribute - Additional Semantics The "job-originating-user-name" Job Description attribute (see[RFC2911], section 4.3.6) remains as the authenticated original user, not the parent Printer's authenticated host, and is forwarded by each client without changing the value.11. Conformance Requirements The Job and Printer Administrative operations defined in this document are OPTIONAL operations. However, some operations MUST be implemented if others are implemented, as shown in Table 9. Table 9. Conformance Requirement Dependencies for Operations Operations REQUIRED If any of these operations are supported: -------------------------------------------------------------------- Enable-Printer Disable-Printer Disable-Printer Enable-Printer Pause-Printer Resume-Printer Resume-Printer Pause-Printer, Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Release-Held-New-Jobs Hold-New-Jobs Activate-Printer, Deactivate-Printer Disable-Printer, Pause-Printer-After-Current-Job Deactivate-Printer, Activate-Printer Enable-Printer, Resume-Printer Restart-Printer none Shutdown-Printer none Startup-Printer none Reprocess-Job none Cancel-Current-Job none Resume-Job Suspend-Current-Job Suspend-Current-Job Resume-JobKugler, et al. Standards Track [Page 38]
RFC 3998 IPP: Job and Printer Operations March 2005 Promote-Job none Schedule-Job-After Promote-Job Tables 10 and 11 list the "printer-state-reasons" and "job-state- reasons" values that are REQUIRED if the indicated operations are supported. Table 10. Conformance Requirement Dependencies for "printer-state-reasons" Values "printer-state- Conformance If any of the following Printer reasons" values: Requirement Operations are supported: -------------------------------------------------------------------- 'paused' REQUIRED Pause-Printer, Pause-Printer-After-Current-Job, or Deactivate-Printer 'hold-new-jobs' REQUIRED Hold-New-Jobs 'moving-to-paused' OPTIONAL Pause-Printer, Pause-Printer-After-Current-Job, Deactivate-Printer 'deactivated' REQUIRED Deactivate-Printer Table 11. Conformance Requirement Dependencies for "job-state- reasons" Values "job-state-reasons" Conformance If any of the following Job values: Requirement operations are supported: 'job-suspended' REQUIRED Suspend-Current-Job 'printer-stopped' REQUIRED Always REQUIRED12. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels",BCP 14,RFC 2119, March 1997. [RFC2246] Dierks, T. and C. Allen, "The TLS Protocol Version 1.0",RFC 2246, January 1999. [RFC2616] Fielding, R., Gettys, J., Mogul, J., Frystyk, H., Masinter, L., Leach, P., and T. Berners-Lee, "Hypertext Transfer Protocol -- HTTP/1.1",RFC 2616, June 1999. [RFC2910] Herriot, R., Butler, S., Moore, P., Turner, R., and J. Wenn, "Internet Printing Protocol/1.1: Encoding and Transport",RFC 2910, September 2000.Kugler, et al. Standards Track [Page 39]
RFC 3998 IPP: Job and Printer Operations March 2005 [RFC2911] Hastings, T., Herriot, R., deBry, R., Isaacson, S., and P. Powell, "Internet Printing Protocol/1.1: Model and Semantics",RFC 2911, September 2000. [RFC3380] Hastings, T., Herriot, R., Kugler, C., and H. Lewis, "Internet Printing Protocol (IPP): Job and Printer Set Operations",RFC 3380, September 2002.13. Informative References [RFC2567] Wright, F., "Design Goals for an Internet Printing Protocol",RFC 2567, April 1999. [RFC2568] Zilles, S., "Rationale for the Structure of the Model and Protocol for the Internet Printing Protocol",RFC 2568, April 1999. [RFC2569] Herriot, R., Hastings, T., Jacobs, N., and J. Martin, "Mapping between LPD and IPP Protocols",RFC 2569, April 1999. [RFC3196] Hastings, T., Manros, C., Zehler, P., Kugler, C., and H. Holst, "Internet Printing Protocol/1.1: Implementor's Guide",RFC 3196, November 2001. [RFC3239] Kugler, C., Lewis, H., and T. Hastings, "Internet Printing Protocol (IPP): Requirements for Job, Printer, and Device Administrative Operations",RFC 3239, February 2002. [RFC3995] Herriot, R. and T. Hastings, "Internet Printing Protocol (IPP): Event Notifications and Subscriptions",RFC 3995, February 2005.14. IANA Considerations This section contains the registration information that IANA added to the IPP Registry according to the procedures defined in[RFC2911], section 6, to cover the definitions in this document. The resulting registrations have been published as additions to thehttp://www.iana.org/assignments/ipp-registrations file.Kugler, et al. Standards Track [Page 40]
RFC 3998 IPP: Job and Printer Operations March 200514.1. Attribute Registrations The following table lists all the attributes defined in this document. These have been registered according to the procedures in[RFC2911], section 6.2. Name Reference Section -------------------------------------- --------- ------- Job Description attributes: original-requesting-user-name (name(MAX)) [RFC3998] 10.8.2 Printer Description attributes: subordinate-printers-supported (1setOf uri) [RFC3998] 7.1 parent-printers-supported (1setOf uri) [RFC3998] 7.2 Operation attributes: original-requesting-user-name (name(MAX)) [RFC3998] 10.8.214.2. Attribute Value Registrations This section lists the additional values defined in this document for existing attributes. Attribute Value Reference Section --------------------- --------- ------- job-state-reasons (1setOf type2 keyword) job-suspended [RFC3998] 9.1 printer-state-reasons (1setOf type2 keyword) hold-new-jobs [RFC3998] 8.1 deactivated [RFC3998] 8.214.3. Additional Enum Attribute Value Registrations The following table lists all the new enum attribute values defined in this document. These have been registered according to the procedures in[RFC2911], section 6.1.Kugler, et al. Standards Track [Page 41]
RFC 3998 IPP: Job and Printer Operations March 2005 Attribute (attribute syntax) Value Name Reference Section ------- -------------------- --------- ------- operations-supported (1setOf type2 enum) [RFC2911] 4.4.1 0x0022 Enable-Printer [RFC3998] 3 0x0023 Disable-Printer [RFC3998] 3 0x0024 Pause-Printer-After-Current-Job [RFC3998] 3 0x0025 Hold-New-Jobs [RFC3998] 3 0x0026 Release-Held-New-Jobs [RFC3998] 3 0x0027 Deactivate-Printer [RFC3998] 3 0x0028 Activate-Printer [RFC3998] 3 0x0029 Restart-Printer [RFC3998] 3 0x002A Shutdown-Printer [RFC3998] 3 0x002B Startup-Printer [RFC3998] 3 0x002C Reprocess-Job [RFC3998] 4 0x002D Cancel-Current-Job [RFC3998] 4 0x002E Suspend-Current-Job [RFC3998] 4 0x002F Resume-Job [RFC3998] 4 0x0030 Promote-Job [RFC3998] 4 0x0031 Schedule-Job-After [RFC3998] 414.4. Operation Registrations The following table lists all the operations defined in this document. These have been registered according to the procedures in[RFC2911], section 6.4. Name Reference Section ----------------------------- --------- ------- Activate-Printer [RFC3998] 3.4.2 Cancel-Current-Job [RFC3998] 4.2 Deactivate-Printer [RFC3998] 3.4.1 Disable-Printer [RFC3998] 3.1.1 Enable-Printer [RFC3998] 3.1.2 Hold-New-Jobs [RFC3998] 3.3.1 Pause-Printer-After-Current-Job [RFC3998] 3.2.1 Promote-Job [RFC3998] 4.4.1 Release-Held-New-Jobs [RFC3998] 3.3.2 Reprocess-Job [RFC3998] 4.1 Restart-Printer [RFC3998] 3.5.1 Resume-Job [RFC3998] 4.3.2 Schedule-Job-After [RFC3998] 4.4.2 Shutdown-Printer [RFC3998] 3.5.2 Startup-Printer [RFC3998] 3.5.3 Suspend-Current-Job [RFC3998] 4.3.1Kugler, et al. Standards Track [Page 42]
RFC 3998 IPP: Job and Printer Operations March 200514.5. Status Code Registrations The following table lists the status code defined in this document. This has been registered according to the procedures in[RFC2911], section 6.6. Value Name Reference Section ------ ------------------------ --------- ------- 0x0000:0x00FF - "successful" none at this time 0x0100:0x01FF - "informational" none at this time 0x0300:0x03FF - "redirection" SeeRFC 2911 Errata none at this time 0x0400:0x04FF - "client-error" none at this time 0x0500:0x05FF - "server-error" 0x050A server-error-printer-is-deactivated [RFC3998] 5.115. Internationalization Considerations This document has the same localization considerations as [RFC2911].16. Security Considerations The IPP Model and Semantics document [RFC2911] discusses high level security requirements (Client Authentication, Server Authentication, and Operation Privacy). Client Authentication is the mechanism by which the client proves its identity to the server in a secure manner. Server Authentication is the mechanism by which the server proves its identity to the client in a secure manner. Operation Privacy is defined as a mechanism for protecting operations from eavesdropping. Printer operations defined in this specification (seesection 3), as well as Pause-Printer, Resume-Printer, and Purge-Job (defined in [RFC2911]) are intended for use by an operator and/or administrator. Job operations defined in this specification (seesection 4) and Cancel-Job, Hold-Job, and Release-Job (defined in [RFC2911]) are intended for use by the job owner, operator, or administrator of the Printer object. These operator and administrator operations affect service for all users.Kugler, et al. Standards Track [Page 43]
RFC 3998 IPP: Job and Printer Operations March 2005 Inappropriate use of an administrative operation by an unauthenticated end user can affect the quality of service for all users. Therefore, IPP Printer implementations MUST support both successful certificate-based TLS [RFC2246] client authentication and successful operator/administrator authorization (see [RFC2911], sections5.2.7 and8, and [RFC2910]) to perform the administrative operations defined in this document. [RFC2910] requires the IPP Printer to support the minimum cipher suite specified for TLS/1.0. The means for authorizing an operator or administrator of the Printer object are outside the scope of this specification,RFC 2910, andRFC2911. The use of TLS and Client Authentication solves the Denial of Service, Man in the Middle, and Masquerading security threats.17. Summary of Base IPP Documents The base set of IPP documents includes the following: Design Goals for an Internet Printing Protocol [RFC2567] Rationale for the Structure and Model and Protocol for the Internet Printing Protocol [RFC2568] Internet Printing Protocol/1.1: Model and Semantics [RFC2911] Internet Printing Protocol/1.1: Encoding and Transport [RFC2910] Internet Printing Protocol/1.1: Implementer's Guide [RFC3196] Mapping between LPD and IPP Protocols [RFC2569] "Design Goals for an Internet Printing Protocol" takes a broad look at distributed printing functionality, and it enumerates real-life scenarios that help clarify the features that have to be included in a printing protocol for the Internet. It identifies requirements for three types of users: end users, operators, and administrators. It calls out a subset of end user requirements that are satisfied in IPP/1.0. A few OPTIONAL operator operations have been added to IPP/1.1. "Rationale for the Structure and Model and Protocol for the Internet Printing Protocol" describes IPP from a high level view, defines a roadmap for the various documents that form the suite of IPP specification documents, and gives background and rationale for the IETF working group's major decisions. "Internet Printing Protocol/1.1: Model and Semantics" describes a simplified model with abstract objects, their attributes, and their operations that are independent of encoding and transport. It introduces a Printer and a Job object. The Job object optionally supports multiple documents per Job. It also addresses security, internationalization, and directory issues.Kugler, et al. Standards Track [Page 44]
RFC 3998 IPP: Job and Printer Operations March 2005 "Internet Printing Protocol/1.1: Encoding and Transport" is a formal mapping of the abstract operations and attributes defined in the model document onto HTTP/1.1 [RFC2616]. It defines the encoding rules for a new Internet MIME media type called "application/ipp". This document also defines the rules for transporting over HTTP a message body whose Content-Type is "application/ipp". This document defines the 'ippget' scheme for identifying IPP printers and jobs. "Internet Printing Protocol/1.1: Implementer's Guide" gives insight and advice to implementers of IPP clients and IPP objects. It is intended to help them understand IPP/1.1 and some of the considerations that may assist them in the design of their client and/or IPP object implementations. For example, a typical order of processing requests is given, including error checking. Motivation for some of the specification decisions is also included. "Mapping between LPD and IPP Protocols" gives some advice to implementers of gateways between IPP and LPD (Line Printer Daemon) implementations.Authors' Addresses Carl Kugler IBM Corporation, 003G 6300 Diagonal Hwy Boulder, CO 80301 Phone: (303) 924-5060 EMail: kugler@us.ibm.com Tom Hastings, editor Xerox Corporation 701 S Aviation Blvd. ESAE 242 El Segundo, CA 90245 Phone: 310-333-6413 Fax: 310-333-6342 EMail: hastings@cp10.es.xerox.com Harry Lewis IBM Corporation 6300 Diagonal Hwy Boulder, CO 80301 Phone: (303) 924-5337 EMail: harryl@us.ibm.comKugler, et al. Standards Track [Page 45]
RFC 3998 IPP: Job and Printer Operations March 2005Full Copyright Statement Copyright (C) The Internet Society (2005). This document is subject to the rights, licenses and restrictions contained inBCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found inBCP 78 andBCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository athttp://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org.Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society.Kugler, et al. Standards Track [Page 46]
[8]ページ先頭