Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]
PROPOSED STANDARD
Internet Engineering Task Force (IETF) V. Singh, Ed.Request for Comments: 7243 J. OttCategory: Standards Track Aalto UniversityISSN: 2070-1721 I. Curcio Nokia Research Center May 2014RTP Control Protocol (RTCP) Extended Report (XR) Blockfor the Bytes Discarded MetricAbstract The RTP Control Protocol (RTCP) is used in conjunction with the Real- time Transport Protocol (RTP) to provide a variety of short-term and long-term reception statistics. The available reporting may include aggregate information across longer periods of time as well as individual packet reporting. This document specifies a report computing the bytes discarded from the de-jitter buffer after successful reception.Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available inSection 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained athttp://www.rfc-editor.org/info/rfc7243.Singh, et al. Standards Track [Page 1]
RFC 7243 RTCP XR Bytes Discarded May 2014Copyright Notice Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject toBCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.Table of Contents1. Introduction ....................................................32. Terminology .....................................................43. Bytes Discarded Report Block ....................................44. Protocol Operation ..............................................64.1. Reporting Node (Receiver) ..................................64.2. Media Sender ...............................................65. SDP Signaling ...................................................76. Security Considerations .........................................77. IANA Considerations .............................................87.1. XR Report Block Registration ...............................87.2. SDP Parameter Registration .................................87.3. Contact Information for IANA Registrations .................88. Acknowledgments .................................................89. References ......................................................99.1. Normative References .......................................99.2. Informative References .....................................9Appendix A. Metrics Represented Using the Template fromRFC 6390 ..11Singh, et al. Standards Track [Page 2]
RFC 7243 RTCP XR Bytes Discarded May 20141. Introduction RTP [RFC3550] provides a transport for real-time media flows such as audio and video together with the RTP Control Protocol (RTCP), which provides periodic feedback about the media streams received in a specific duration. In addition, RTCP can be used for timely feedback about individual events to report (e.g., packet loss) [RFC4585]. Both long-term and short-term feedback enable a media sender to adapt its media transmission and/or encoding dynamically to the observed path characteristics. [RFC3611] defines RTCP Extended Reports as a detailed reporting framework to provide more than just the coarse Receiver Report (RR) statistics. The detailed reporting may enable a media sender to react more appropriately to the observed networking conditions as these can be characterized better, although at the expense of extra overhead. In addition to lost packets, [RFC3611] defines the notion of "discarded" packets: packets that were received but dropped from the de-jitter buffer because they were either too early (for buffering) or too late (for playout). The "discard rate" metric is part of the VoIP metrics report block even though it is not just applicable to audio: it is specified as the fraction of discarded packets since the beginning of the session. SeeSection 4.7.1 of [RFC3611]. The discard metric is believed to be applicable to a large class of RTP applications that use a de-jitter buffer [RFC5481]. Recently proposed extensions to the Extended Reports (XR) reporting suggest enhancing the discard metric: o Reporting the number of discarded packets in a measurement interval, i.e., during either the last reporting interval or since the beginning of the session, as indicated by a flag in the suggested XR report [RFC7002]. If an endpoint needs to report packet discard due to other reasons than early- and late-arrival (for example, discard due to duplication, redundancy, etc.) then it should consider using the Discarded Packets Report Block [RFC7002]. o Reporting gaps and bursts of discarded packets during a measurement interval, i.e., the last reporting interval or the duration of the session [RFC7003]. o Reporting run-length encoding of a discarded packet during a measurement interval, i.e., between a set of sequence numbers [RFC7097].Singh, et al. Standards Track [Page 3]
RFC 7243 RTCP XR Bytes Discarded May 2014 However, none of these metrics allow a receiver to report precisely the number of RTP payload bytes that were discarded. While this information could in theory be derived from high-frequency reporting on the number of discarded packets [RFC7002] or from the Discard RLE (Run Length Encoding) report [RFC7097], these two mechanisms do not appear feasible. The former would require an unduly high amount of reporting that still might not be sufficient due to the non- deterministic scheduling of RTCP packets. The latter incurs significant complexity (by storing a map of sequence numbers and packet sizes) and reporting overhead. An XR block is defined in this document to indicate the number of RTP payload bytes discarded, per interval or for the duration of the session, similar to the other XR blocks.2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described inBCP 14, [RFC2119]. The terminology defined in RTP [RFC3550] and in the extensions for XR reporting [RFC3611] applies.3. Bytes Discarded Report Block The Bytes Discarded Report Block uses the following format, which follows the model of the framework for performance metric development [RFC6390]. 0 1 2 3 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | BT=26 | I |E|Reserved | Block length=2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SSRC of source | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Number of RTP payload bytes discarded | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1: XR Bytes Discarded Report Block Block Type (BT): 8 bits. A Bytes Discarded Packets Report Block is identified by the constant 26. Interval Metric flag (I): 2 bits. It is used to indicate whether the discard metric is an Interval or a Cumulative metric, that is, whether the reported value applies to the most recent measurementSingh, et al. Standards Track [Page 4]
RFC 7243 RTCP XR Bytes Discarded May 2014 interval duration between successive reports (I=10, the Interval Duration) or to the accumulation period characteristic of cumulative measurements (I=11, the Cumulative Duration). Since the bytes discarded are not measured at a particular time instance but over one or several reporting intervals, the metric MUST NOT be reported as a Sampled Metric (I=01). In addition, the value I=00 is reserved and MUST NOT be sent, and it MUST be discarded when received. Early bit (E): It is introduced to distinguish between packets discarded due to early arrival and those discarded due to late arrival. The E bit is set to '1' if it reports bytes discarded due to early arrival and is set to '0' if it reports bytes discarded due to late arrival. If a duplicate packet is received and discarded, these duplicate packets are ignored and not reported. In case both early and late discarded packets shall be reported, two Bytes Discarded report blocks MUST be included. Reserved: 5 bits. This field is reserved for future definition. In the absence of such definition, the bits in this field MUST be set to zero and MUST be ignored by the receiver. Block length: 16 bits. It MUST be set to 2, in accordance with the definition of this field in [RFC3611]. The block MUST be discarded if the block length is set to a different value. Number of RTP payload bytes discarded: It is a 32-bit unsigned integer value indicating the total number of bytes discarded. The 'bytes discarded' corresponds to the RTP payload size of every RTP packet that is discarded (due to early or late arrival). Hence, the 'bytes discarded' ignores the size of any RTP header extensions and the size of the padding bits. Also the discarded packet is associated to the interval in which it was discarded, not when it was expected. If the Interval Metric flag is set as I=11, the value in the field indicates the number of RTP payload bytes discarded from the start of the session; if the Interval Metric flag is set as I=10, it indicates the number of bytes discarded in the most recent reporting interval. If the XR block follows a Measurement Information Block [RFC6776] in the same RTCP compound packet, then the cumulative (I=11) or the interval (I=10) for this report block corresponds to the values of the "measurement duration" in the Measurement Information Block. If the receiver sends the Bytes Discarded Report Block without the Measurement Information Block, then the Bytes Discarded Report Block MUST be sent in conjunction with an RTCP Receiver Report (RR) as a compound RTCP packet.Singh, et al. Standards Track [Page 5]
RFC 7243 RTCP XR Bytes Discarded May 20144. Protocol Operation This section describes the behavior of the reporting node (i.e., the media receiver) and the media sender.4.1. Reporting Node (Receiver) The media receiver MAY send the Bytes Discarded Reports as part of the regularly scheduled RTCP packets as perRFC 3550. It MAY also include Bytes Discarded Reports in immediate or early feedback packets as per [RFC4585]. Transmission of the RTCP XR Bytes Discarded Report is up to the discretion of the media receiver, as is the reporting granularity. However, it is RECOMMENDED that the media receiver signals the bytes discarded packets using the method defined in this document. When reporting several metrics in a single RTCP packet, the reporting intervals for the report blocks are synchronized, therefore the media receiver may choose to additionally send the Discarded Packets [RFC7002] or Discard RLE [RFC7097] Report Block to assist the media sender in correlating the bytes discarded to the packets discarded in that particular interval. If all packets over a reporting period were discarded, the media receiver MAY use the Discarded Packets Report Block [RFC7002] instead.4.2. Media Sender The media sender MUST be prepared to operate without receiving any Bytes Discarded reports. If Bytes Discarded reports are generated by the media receiver, the media sender cannot rely on all these reports being received, nor can the media sender rely on a regular generation pattern from the media receiver. However, if the media sender receives any RTCP reports but no Bytes Discarded report blocks and is aware that the media receiver supports Bytes Discarded report blocks, it MAY assume that no packets were discarded by the media receiver. The media sender SHOULD accept the Bytes Discarded Report Block only if it is received in a compound RTCP receiver report or if it is preceded by a Measurement Information Block [RFC6776]. Under all other circumstances, it MUST ignore the block.Singh, et al. Standards Track [Page 6]
RFC 7243 RTCP XR Bytes Discarded May 20145. SDP Signaling A participant of a media session MAY use SDP to signal its support for the report block specified in this document or use them without any prior signaling (seeSection 5 of [RFC3611]). For signaling in SDP, the RTCP XR attribute as defined in [RFC3611] MUST be used. The SDP [RFC4566] attribute 'xr-format' defined inRFC3611 is augmented to indicate the Bytes Discarded metric. This is described in the following ABNF [RFC5234]: rtcp-xr-attrib = "a=" "rtcp-xr" ":" [xr-format *(SP xr-format)] CRLF ; defined in [RFC3611] xr-format =/ xr-discard-bytes xr-discard-bytes = "discard-bytes" The parameter 'discard-bytes' to indicate support for the Bytes Discarded Report Block is defined inSection 3. When SDP is used in the offer/answer context, the mechanism defined in [RFC3611] for unilateral "rtcp-xr" attribute parameters applies (seeSection 5.2 of [RFC3611]).6. Security Considerations The Bytes Discarded block does not provide per-packet statistics, hence the risk to confidentiality documented inSection 7, paragraph 3 of [RFC3611] does not apply. In some situations, returning very detailed error information (e.g., over-range measurement or measurement unavailable) using this report block can provide an attacker with insight into the security processing. For example, assume that the attacker sends a packet with a stale timestamp (i.e., time in the past) to the receiver. If the receiver now sends a discard report with the same number of bytes as the payload of the injected packet, the attacker can infer that no security processing was performed. If, on the other hand, the attacker does not receive a discard report, it can equivalently assume that the security procedures were performed on the packet. Implementers should therefore consider the guidance in [RFC7202] for using appropriate security mechanisms, i.e., where security is a concern, the implementation should apply encryption and authentication to the report block. For example, this can be achieved by using the AVPF profile together with the Secure RTPSingh, et al. Standards Track [Page 7]
RFC 7243 RTCP XR Bytes Discarded May 2014 profile as defined in [RFC3711]; an appropriate combination of the two profiles (an "SAVPF") is specified in [RFC5124]. However, other mechanisms also exist (documented in [RFC7201]) and might be more suitable. The Bytes Discarded report is employed by the sender to perform congestion control, typically, for calculating goodput (i.e., throughput that is useful). In these cases, an attacker MAY drive the endpoint to lower its sending rate and under-utilize the link; therefore, media senders should choose appropriate security measures to mitigate such attacks. Lastly, the security considerations of [RFC3550], [RFC3611], and [RFC4585] apply.7. IANA Considerations New block types for RTCP XR are subject to IANA registration. For general guidelines on IANA considerations for RTCP XR, refer to [RFC3611].7.1. XR Block Registration This document registers a new value in the IANA "RTP Control Protocol Extended Reports (RTCP XR) Block Type Registry": 26 for BDR (Bytes Discarded Report).7.2. SDP Parameter Registration This document registers a new parameter for the Session Description Protocol (SDP), "discard-bytes" in the "RTP Control Protocol Extended Reports (RTCP XR) Session Description Protocol (SDP) Parameters Registry".7.3. Contact Information for IANA Registrations RAI Area Directors <rai-ads@tools.ietf.org>8. Acknowledgments The authors would like to thank Benoit Claise, Alan Clark, Roni Even, Vijay Gurbani, Sam Hartman, Vinayak Hegde, Jeffrey Hutzelman, Barry Leiba, Colin Perkins, Dan Romascanu, Dan Wing, and Qin Wu for providing valuable feedback on this document during its development.Singh, et al. Standards Track [Page 8]
RFC 7243 RTCP XR Bytes Discarded May 20149. References9.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels",BCP 14,RFC 2119, March 1997. [RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, "RTP: A Transport Protocol for Real-Time Applications", STD 64,RFC 3550, July 2003. [RFC3611] Friedman, T., Caceres, R., and A. Clark, "RTP Control Protocol Extended Reports (RTCP XR)",RFC 3611, November 2003. [RFC4566] Handley, M., Jacobson, V., and C. Perkins, "SDP: Session Description Protocol",RFC 4566, July 2006. [RFC4585] Ott, J., Wenger, S., Sato, N., Burmeister, C., and J. Rey, "Extended RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/AVPF)",RFC 4585, July 2006. [RFC5234] Crocker, D., Ed., and P. Overell, "Augmented BNF for Syntax Specifications: ABNF", STD 68,RFC 5234, January 2008. [RFC6390] Clark, A. and B. Claise, "Guidelines for Considering New Performance Metric Development",BCP 170,RFC 6390, October 2011. [RFC6776] Clark, A. and Q. Wu, "Measurement Identity and Information Reporting Using a Source Description (SDES) Item and an RTCP Extended Report (XR) Block",RFC 6776, October 2012. [RFC7002] Clark, A., Zorn, G., and Q. Wu, "RTP Control Protocol (RTCP) Extended Report (XR) Block for Discard Count Metric Reporting",RFC 7002, September 2013.9.2. Informative References [RFC3711] Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K. Norrman, "The Secure Real-time Transport Protocol (SRTP)",RFC 3711, March 2004. [RFC5124] Ott, J. and E. Carrara, "Extended Secure RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/SAVPF)",RFC 5124, February 2008.Singh, et al. Standards Track [Page 9]
RFC 7243 RTCP XR Bytes Discarded May 2014 [RFC5481] Morton, A. and B. Claise, "Packet Delay Variation Applicability Statement",RFC 5481, March 2009. [RFC7003] Clark, A., Huang, R., and Q. Wu, "RTP Control Protocol (RTCP) Extended Report (XR) Block for Burst/Gap Discard Metric Reporting",RFC 7003, September 2013. [RFC7097] Ott, J., Singh, V., and I. Curcio, "RTP Control Protocol (RTCP) Extended Report (XR) for RLE of Discarded Packets",RFC 7097, January 2014. [RFC7201] Westerlund, M. and C. Perkins, "Options for Securing RTP Sessions",RFC 7201, April 2014. [RFC7202] Perkins, C. and M. Westerlund, "Securing the RTP Framework: Why RTP Does Not Mandate a Single Media Security Solution",RFC 7202, April 2014.Singh, et al. Standards Track [Page 10]
RFC 7243 RTCP XR Bytes Discarded May 2014Appendix A. Metrics Represented Using the Template fromRFC 6390 a. RTP Payload Bytes Discarded Metric * Metric Name: RTP Payload Bytes Discarded Metric * Metric Description: Total number of RTP payload bytes discarded over the period covered by this report. * Method of Measurement or Calculation: See the definition of "Number of RTP payload bytes discarded" inSection 3. * Units of Measurement: See the definition of "Number of RTP payload bytes discarded" inSection 3. * Measurement Point(s) with Potential Measurement Domain: See the first paragraph ofSection 3. * Measurement Timing: See the last three paragraphs ofSection 3 for measurement timing and for the Interval Metric flag. * Use and applications: See the third paragraph ofSection 1. * Reporting model: SeeRFC 3611.Singh, et al. Standards Track [Page 11]
RFC 7243 RTCP XR Bytes Discarded May 2014Authors' Addresses Varun Singh (editor) Aalto University School of Electrical Engineering Otakaari 5 A Espoo, FIN 02150 Finland EMail: varun@comnet.tkk.fi URI:http://www.netlab.tkk.fi/~varun/ Joerg Ott Aalto University School of Electrical Engineering Otakaari 5 A Espoo, FIN 02150 Finland EMail: jo@comnet.tkk.fi Igor D.D. Curcio Nokia Research Center P.O. Box 1000 (Visiokatu 3) Tampere, FIN 33721 Finland EMail: igor.curcio@nokia.comSingh, et al. Standards Track [Page 12]
[8]ページ先頭