Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]
INFORMATIONAL
Internet Engineering Task Force (IETF) J. XiaRequest for Comments: 6828 HuaweiCategory: Informational January 2013ISSN: 2070-1721Content Splicing for RTP SessionsAbstract Content splicing is a process that replaces the content of a main multimedia stream with other multimedia content and delivers the substitutive multimedia content to the receivers for a period of time. Splicing is commonly used for insertion of local advertisements by cable operators, whereby national advertisement content is replaced with a local advertisement. This memo describes some use cases for content splicing and a set of requirements for splicing content delivered by RTP. It provides concrete guidelines for how an RTP mixer can be used to handle content splicing.Status of This Memo This document is not an Internet Standards Track specification; it is published for informational purposes. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Not all documents approved by the IESG are a candidate for any level of Internet Standard; seeSection 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained athttp://www.rfc-editor.org/info/rfc6828.Xia Informational [Page 1]
RFC 6828 RTP Splicing January 2013Copyright Notice Copyright (c) 2013 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject toBCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.Table of Contents1. Introduction ....................................................22. System Model and Terminology ....................................33. Requirements for RTP Splicing ...................................64. Content Splicing for RTP Sessions ...............................74.1. RTP Processing in RTP Mixer ................................74.2. RTCP Processing in RTP Mixer ...............................8 4.3. Considerations for Handling Media Clipping at the RTP Layer .................................................104.4. Congestion Control Considerations .........................114.5. Considerations for Implementing Undetectable Splicing .....135. Implementation Considerations ..................................136. Security Considerations ........................................147. Acknowledgments ................................................158. References .....................................................158.1. Normative References ......................................158.2. Informative References ....................................15Appendix A. Why Mixer Is Chosen ...................................171. Introduction This document outlines how content splicing can be used in RTP sessions. Splicing, in general, is a process where part of a multimedia content is replaced with other multimedia content and delivered to the receivers for a period of time. The substitutive content can be provided, for example, via another stream or via local media file storage. One representative use case for splicing is local advertisement insertion. This allows content providers to replace national advertising content with their own regional advertising content prior to delivering the regional advertising content to the receivers. Besides the advertisement insertion use case, there are other use cases in which the splicing technology canXia Informational [Page 2]
RFC 6828 RTP Splicing January 2013 be applied, for example, splicing a recorded video into a video conferencing session or implementing a playlist server that stitches pieces of video together. Content splicing is a well-defined operation in MPEG-based cable TV systems. Indeed, the Society for Cable Telecommunications Engineers (SCTE) has created two standards, [SCTE30] and [SCTE35], to standardize MPEG2-TS splicing procedures. SCTE 30 creates a standardized method for communication between advertisement server and splicer, and SCTE 35 supports splicing of MPEG2 transport streams. When using multimedia splicing into the Internet, the media may be transported by RTP. In this case, the original media content and substitutive media content will use the same time period but may contain different numbers of RTP packets due to different media codecs and entropy coding. This mismatch may require some adjustments of the RTP header sequence number to maintain consistency. [RFC3550] provides the tools to enable seamless content splicing in RTP sessions, but to date there have been no clear guidelines on how to use these tools. This memo outlines the requirements for content splicing in RTP sessions and describes how an RTP mixer can be used to meet these requirements.2. System Model and Terminology In this document, the splicer, an intermediary network element, handles RTP splicing. The splicer can receive main content and substitutive content simultaneously but will send one of them at one point of time. When RTP splicing begins, the splicer sends the substitutive content to the RTP receiver instead of the main content for a period of time. When RTP splicing ends, the splicer switches back to sending the main content to the RTP receiver. A simplified RTP splicing diagram is depicted in Figure 1, in which only one main content flow and one substitutive content flow are given. Actually, the splicer can handle multiple splicing for multiple RTP sessions simultaneously. RTP splicing may happen more than once in multiple time slots during the lifetime of the main RTP stream. The methods by which the splicer learns when to start and end the splicing are out of scope for this document.Xia Informational [Page 3]
RFC 6828 RTP Splicing January 2013 +---------------+ | | Main Content +-----------+ | Main RTP |------------->| | Output Content | Content | | Splicer |---------------> +---------------+ ---------->| | | +-----------+ | | Substitutive Content | | +-----------------------+ | Substitutive RTP | | Content | | or | | Local File Storage | +-----------------------+ Figure 1: RTP Splicing Architecture This document uses the following terminologies. Output RTP Stream The RTP stream that the RTP receiver is currently receiving. The content of the output of the RTP stream can be either main content or substitutive content. Main Content The multimedia content that is conveyed in the main RTP stream. Main content will be replaced by the substitutive content during splicing. Main RTP Stream The RTP stream that the splicer is receiving. The content of the main RTP stream can be replaced by substitutive content for a period of time. Main RTP Sender The sender of RTP packets carrying the main RTP stream.Xia Informational [Page 4]
RFC 6828 RTP Splicing January 2013 Substitutive Content The multimedia content that replaces the main content during splicing. The substitutive content can, for example, be contained in an RTP stream from a media sender or fetched from local media file storage. Substitutive RTP Stream An RTP stream with new content that will replace the content in the main RTP stream. The substitutive RTP stream and main RTP stream are two separate streams. If the substitutive content is provided via a substitutive RTP stream, the substitutive RTP stream must pass through the splicer before the substitutive content is delivered to the receiver. Substitutive RTP Sender The sender of RTP packets carrying the substitutive RTP stream. Splicing-In Point A virtual point in the RTP stream, suitable for substitutive content entry, typically in the boundary between two independently decodable frames. Splicing-Out Point A virtual point in the RTP stream, suitable for substitutive content exit, typically in the boundary between two independently decodable frames. Splicer An intermediary node that inserts substitutive content into a main RTP stream. The splicer sends substitutive content to the RTP receiver instead of main content during splicing. It is also responsible for processing RTP Control Protocol (RTCP) traffic between the RTP sender and the RTP receiver.Xia Informational [Page 5]
RFC 6828 RTP Splicing January 20133. Requirements for RTP Splicing In order to allow seamless content splicing at the RTP layer, the following requirements must be met. Meeting these will also allow, but not require, seamless content splicing at layers above RTP. REQ-1: The splicer should be agnostic about the network and transport-layer protocols used to deliver the RTP streams. REQ-2: The splicing operation at the RTP layer must allow splicing at any point required by the media content and must not constrain when splicing-in or splicing-out operations can take place. REQ-3: Splicing of RTP content must be backward compatible with the RTP/RTCP protocol, associated profiles, payload formats, and extensions. REQ-4: The splicer will modify the content of RTP packets and thus break the end-to-end security, at a minimum, breaking the data integrity and source authentication. If the splicer is designated to insert substitutive content, it must be trusted, i.e., be in the security context(s) with the main RTP sender, the substitutive RTP sender, and the receivers. If encryption is employed, the splicer commonly must decrypt the inbound RTP packets and re-encrypt the outbound RTP packets after splicing. REQ-5: The splicer should rewrite as necessary and forward RTCP messages (e.g., including packet loss, jitter, etc.) sent from a downstream receiver to the main RTP sender or the substitutive RTP sender, and thus allow the main RTP sender or substitutive RTP sender to learn the performance of the downstream receiver when its content is being passed to an RTP receiver. In addition, the splicer should rewrite RTCP messages from the main RTP sender or substitutive RTP sender to the receiver.Xia Informational [Page 6]
RFC 6828 RTP Splicing January 2013 REQ-6: The splicer must not affect other RTP sessions running between the RTP sender and the RTP receiver and must be transparent for the RTP sessions it does not splice. REQ-7: The RTP receiver should not be able to detect any splicing points in the RTP stream produced by the splicer on the RTP protocol level. For the advertisement insertion use case, it is important to make it difficult for the RTP receiver to detect where an advertisement insertion is starting or ending from the RTP packets, and thus avoiding the RTP receiver from filtering out the advertisement content. This memo only focuses on making the splicing undetectable at the RTP layer. The corresponding processing is depicted inSection 4.5.4. Content Splicing for RTP Sessions The RTP specification [RFC3550] defines two types of middleboxes: RTP translators and RTP mixers. Splicing is best viewed as a mixing operation. The splicer generates a new RTP stream that is a mix of the main RTP stream and the substitutive RTP stream. An RTP mixer is therefore an appropriate model for a content splicer. In the next four subsections (fromSection 4.1 toSection 4.4), the document analyzes how the mixer handles RTP splicing and how it satisfies the general requirements listed in Section 3. InSection 4.5, the document looks at REQ-7 in order to hide the fact that splicing takes place.4.1. RTP Processing in RTP Mixer A splicer could be implemented as a mixer that receives the main RTP stream and the substitutive content (possibly via a substitutive RTP stream), and sends a single output RTP stream to the receiver(s). That output RTP stream will contain either the main content or the substitutive content. The output RTP stream will come from the mixer and will have the synchronization source (SSRC) of the mixer rather than the main RTP sender or the substitutive RTP sender. The mixer uses its own SSRC, sequence number space, and timing model when generating the output stream. Moreover, the mixer may insert the SSRC of the main RTP stream into the contributing source (CSRC) list in the output media stream.Xia Informational [Page 7]
RFC 6828 RTP Splicing January 2013 At the splicing-in point, when the substitutive content becomes active, the mixer chooses the substitutive RTP stream as the input stream and extracts the payload data (i.e., substitutive content). If the substitutive content comes from local media file storage, the mixer directly fetches the substitutive content. After that, the mixer encapsulates substitutive content instead of main content as the payload of the output media stream and then sends the output RTP media stream to the receiver. The mixer may insert the SSRC of the substitutive RTP stream into the CSRC list in the output media stream. If the substitutive content comes from local media file storage, the mixer should leave the CSRC list blank. At the splicing-out point, when the substitutive content ends, the mixer retrieves the main RTP stream as the input stream and extracts the payload data (i.e., main content). After that, the mixer encapsulates main content instead of substitutive content as the payload of the output media stream and then sends the output media stream to the receivers. Moreover, the mixer may insert the SSRC of the main RTP stream into the CSRC list in the output media stream as before. Note that if the content is too large to fit into RTP packets sent to the RTP receiver, the mixer needs to transcode or perform application-layer fragmentation. Usually the mixer is deployed as part of a managed system and MTU will be carefully managed by this system. This document does not raise any new MTU related issues compared to a standard mixer described in [RFC3550]. Splicing may occur more than once during the lifetime of the main RTP stream. This means the mixer needs to send main content and substitutive content in turn with its own SSRC identifier. From receiver point of view, the only source of the output stream is the mixer regardless of where the content is coming from.4.2. RTCP Processing in RTP Mixer By monitoring available bandwidth and buffer levels and by computing network metrics such as packet loss, network jitter, and delay, an RTP receiver can learn the network performance and communicate this to the RTP sender via RTCP reception reports. According to the description inSection 7.3 of [RFC3550], the mixer splits the RTCP flow between the sender and receiver into two separate RTCP loops; the RTP sender has no idea about the situation on the receiver. But splicing is a process where the mixer selects one media stream from multiple streams rather than mixing them, so the mixer can leave the SSRC identifier in the RTCP report intactXia Informational [Page 8]
RFC 6828 RTP Splicing January 2013 (i.e., the SSRC of the downstream receiver). This enables the main RTP sender or the substitutive RTP sender to learn the situation on the receiver. If the RTCP report corresponds to a time interval that is entirely main content or entirely substitutive content, the number of output RTP packets containing substitutive content is equal to the number of input substitutive RTP packets (from the substitutive RTP stream) during splicing. In the same manner, the number of output RTP packets containing main content is equal to the number of input main RTP packets (from the main RTP stream) during non-splicing unless the mixer fragments the input RTP packets. This means that the mixer does not need to modify the loss packet fields in reception report blocks in RTCP reports. But, if the mixer fragments the input RTP packets, it may need to modify the loss packet fields to compensate for the fragmentation. Whether the input RTP packets are fragmented or not, the mixer still needs to change the SSRC field in the report block to the SSRC identifier of the main RTP sender or the substitutive RTP sender and rewrite the extended highest sequence number field to the corresponding original extended highest sequence number before forwarding the RTCP report to the main RTP sender or the substitutive RTP sender. If the RTCP report spans the splicing-in point or the splicing-out point, it reflects the characteristics of the combination of main RTP packets and substitutive RTP packets. In this case, the mixer needs to divide the RTCP report into two separate RTCP reports and send them to their original RTP senders, respectively. For each RTCP report, the mixer also needs to make the corresponding changes to the packet loss fields in the report block besides the SSRC field and the extended highest sequence number field. If the mixer receives an RTCP extended report (XR) block, it should rewrite the XR report block in a similar way to the reception report block in the RTCP report. Besides forwarding the RTCP reports sent from the RTP receiver, the mixer can also generate its own RTCP reports to inform the main RTP sender, or the substitutive RTP sender, of the reception quality of content not sent to the RTP receiver when it reaches the mixer. These RTCP reports use the SSRC of the mixer. If the substitutive content comes from local media file storage, the mixer does not need to generate RTCP reports for the substitutive stream.Xia Informational [Page 9]
RFC 6828 RTP Splicing January 2013 Based on the above RTCP operating mechanism, the RTP sender whose content is being passed to a receiver will see the reception quality of its stream as received by the mixer and the reception quality of the spliced stream as received by the receiver. The RTP sender whose content is not being passed to a receiver will only see the reception quality of its stream as received by the mixer. The mixer must forward RTCP source description (SDES) and BYE packets from the receiver to the sender and may forward them in inverse direction as defined inSection 7.3 of [RFC3550]. Once the mixer receives an RTP/Audio-Visual Profile with Feedback (AVPF) [RFC4585] transport-layer feedback packet, it must handle it carefully, as the feedback packet may contain the information of the content that comes from different RTP senders. In this case, the mixer needs to divide the feedback packet into two separate feedback packets and process the information in the feedback control information (FCI) in the two feedback packets, just as in the RTCP report process described above. If the substitutive content comes from local media file storage (i.e., the mixer can be regarded as the substitutive RTP sender), any RTCP packets received from downstream related to the substitutive content must be terminated on the mixer without any further processing.4.3. Considerations for Handling Media Clipping at the RTP Layer This section provides informative guidelines on how to handle media substitution at the RTP layer to minimize media impact. Dealing well with the media substitution at the RTP layer is necessary for quality implementations. To perfectly erase any media impact needs more considerations at the higher layers. How the media substitution is erased at the higher layers is outside of the scope of this memo. If the time duration for any substitutive content mismatches, i.e., shorter or longer than the duration of the main content to be replaced, then media degradations may occur at the splicing point and thus impact the user's experience. If the substitutive content has shorter duration from the main content, then there could be a gap in the output RTP stream. The RTP sequence number will be contiguous across this gap, but there will be an unexpected jump in the RTP timestamp. Such a gap would cause the receiver to have nothing to play. This may be unavoidable, unless the mixer can adjusts the splice in or splice out point to compensate. This assumes the splicing mixer can send more of the main RTP stream in place of the shorter substitutive stream or varyXia Informational [Page 10]
RFC 6828 RTP Splicing January 2013 the length of the substitutive content. It is the responsibility of the higher-layer protocols and the media providers to ensure that the substitutive content is of very similar duration as the main content to be replaced. If the substitute content has longer duration than the reserved gap duration, there will be an overlap between the substitutive RTP stream and the main RTP stream at the splicing-out point. A straightforward approach is that the mixer performs an ungraceful action and terminates the splicing and switches back to the main RTP stream even if this may cause media stuttering on the receiver. Alternatively, the mixer may transcode the substitutive content to play at a faster rate than normal, to adjust it to the length of the gap in the main content and generate a new RTP stream for the transcoded content. This is a complex operation and very specific to the content and media codec used. Additional approaches exist; these types of issues should be taken into account in both mixer implementors and media generators to enable smooth substitutions.4.4. Congestion Control Considerations If the substitutive content has somewhat different characteristics from the main content it replaces, or if the substitutive content is encoded with a different codec or has different encoding bitrate, it might overload the network and might cause network congestion on the path between the mixer and the RTP receiver(s) that would not have been caused by the main content. To be robust to network congestion and packet loss, a mixer that is performing splicing must continuously monitor the status of a downstream network by monitoring any of the following RTCP reports that are used: 1. RTCP receiver reports indicate packet loss [RFC3550]. 2. RTCP NACKs for lost packet recovery [RFC4585]. 3. RTCP Explicit Congestion Notification (ECN) Feedback information [RFC6679].Xia Informational [Page 11]
RFC 6828 RTP Splicing January 2013 Once the mixer detects congestion on its downstream link, it will treat these reports as follows: 1. If the mixer receives the RTCP receiver reports with packet loss indication, it will forward the reports to the substitutive RTP sender or the main RTP sender as described inSection 4.2. 2. If mixer receives the RTCP NACK packets defined in [RFC4585] from the RTP receiver for packet loss recovery, it first identifies the content category of lost packets to which the NACK corresponds. Then, the mixer will generate new RTCP NACKs for the lost packets with its own SSRC and make corresponding changes to their sequence numbers to match original, pre-spliced, packets. If the lost substitutive content comes from local media file storage, the mixer acting as the substitutive RTP sender will directly fetch the lost substitutive content and retransmit it to the RTP receiver. The mixer may buffer the sent RTP packets and do the retransmission. It is somewhat complex that the lost packets requested in a single RTCP NACK message not only contain the main content but also the substitutive content. To address this, the mixer must divide the RTCP NACK packet into two separate RTCP NACK packets: one requests for the lost main content, and another requests for the lost substitutive content. 3. If an ECN-aware mixer receives RTCP ECN feedback (RTCP ECN feedback packets or RTCP XR summary reports) defined in [RFC6679] from the RTP receiver, it must process them in a similar way to the RTP/AVPF feedback packet or RTCP XR process described inSection 4.2 of this memo. These three methods require the mixer to run a congestion control loop and bitrate adaptation between itself and the RTP receiver. The mixer can thin or transcode the main RTP stream or the substitutive RTP stream, but such operations are very inefficient and difficult, and they also bring undesirable delay. Fortunately, as noted in this memo, the mixer acting as a splicer can rewrite the RTCP packets sent from the RTP receiver and forward them to the RTP sender, thus letting the RTP sender knows that congestion is being experienced on the path between the mixer and the RTP receiver. Then, the RTP sender applies its congestion control algorithm and reduces the media bitrate to a value that is in compliance with congestion control principles for the slowest link. The congestion control algorithm may be a TCP-friendly bitrate adaptation algorithm specified in [RFC5348] or a Datagram Congestion Control Protocol (DCCP) congestion control algorithm defined in [RFC5762].Xia Informational [Page 12]
RFC 6828 RTP Splicing January 2013 If the substitutive content comes from local media file storage, the mixer must directly reduce the bitrate as if it were the substitutive RTP sender. From the above analysis, to reduce the risk of congestion and maintain the bandwidth consumption stable over time, the substitutive RTP stream is recommended to be encoded at an appropriate bitrate to match that of the main RTP stream. If the substitutive RTP stream comes from the substitutive RTP sender, this sender should have some knowledge about the media encoding bitrate of the main content in advance. Acquiring such knowledge is out of scope in this document.4.5. Considerations for Implementing Undetectable Splicing If it is desirable to prevent receivers from detecting that splicing is occurring at the RTP layer, the mixer must not include a CSRC list in outgoing RTP packets and must not forward RTCP messages from the main RTP sender or from the substitutive RTP sender. Due to the absence of a CSRC list in the output RTP stream, the RTP receiver only initiates SDES, BYE, and Application-specific functions (APP) packets to the mixer without any knowledge of the main RTP sender and the substitutive RTP sender. The CSRC list identifies the contributing sources; these SSRC identifiers of contributing sources are kept globally unique for each RTP session. The uniqueness of the SSRC identifier is used to resolve collisions and to detect RTP-level forwarding loops as defined inSection 8.2 of [RFC3550]. A danger that loops involving those contributing sources will not be detected will be created by the absence of a CSRC list in this case. The loops could occur if either the mixer is misconfigured to form a loop or a second mixer/translator is added, causing packets to loop back to upstream of the original mixer. An undetected RTP packet loop is a serious denial-of-service threat, which can consume all available bandwidth or mixer processing resources until the looped packets are dropped as a result of congestion. So, non-RTP means must be used to detect and resolve loops if the mixer does not add a CSRC list.5. Implementation Considerations When the mixer is used to handle RTP splicing, the RTP receiver does not need any RTP/RTCP extension for splicing. As a trade-off, additional overhead could be induced on the mixer, which uses its own sequence number space and timing model. So the mixer will rewrite the RTP sequence number and timestamp, whatever splicing is active or not, and generate RTCP flows for both sides. In case the mixer serves multiple main RTP streams simultaneously, this may lead to more overhead on the mixer.Xia Informational [Page 13]
RFC 6828 RTP Splicing January 2013 If an undetectable splicing requirement is required, the CSRC list is not included in the outgoing RTP packet; this brings a potential issue with loop detection as briefly described inSection 4.5.6. Security Considerations The splicing application is subject to the general security considerations of the RTP specification [RFC3550]. The mixer acting as splicer replaces some content with other content in RTP packets, thus breaking any RTP-level end-to-end security, such as integrity protection and source authentication. Thus, any RTP-level or outside security mechanism, such as IPsec [RFC4301] or Datagram Transport Layer Security [RFC6347], will use a security association between the splicer and the receiver. When using the Secure Real-Time Transport Protocol (SRTP) [RFC3711], the splicer could be provisioned with the same security association as the main RTP sender. Using a limitation in the SRTP security services regarding source authentication, the splicer can modify and re-protect the RTP packets without enabling the receiver to detect if the data comes from the original source or from the splicer. Security goals to have source authentication all the way from the RTP main sender to the receiver through the splicer is not possible with splicing and any existing solutions. A new solution can theoretically be developed that enables identifying the participating entities and what each provides, i.e., the different media sources, main and substituting, and the splicer providing the RTP-level integration of the media payloads in a common timeline and synchronization context. Such a solution would obviously not meet REQ-7 and will be detectable on the RTP level. The nature of this RTP service offered by a network operator employing a content splicer is that the RTP-layer security relationship is between the receiver and the splicer, and between the sender and the splicer, but is not end-to-end between the receiver and the sender. This appears to invalidate the undetectability goal, but in the common case, the receiver will consider the splicer as the main media source. Some RTP deployments use RTP payload security mechanisms (e.g., ISMACryp [ISMACryp]). If any payload internal security mechanisms are used, only the RTP sender and the RTP receiver establish that security context, in which case any middlebox (e.g., splicer) between the RTP sender and the RTP receiver will not get such keying material. This may impact the splicer's ability to perform splicing if it is dependent on RTP payload-level hints for finding the splice in and out points. However, other potential solutions exist toXia Informational [Page 14]
RFC 6828 RTP Splicing January 2013 specify or mark where the splicing points exist in the media streams. When using RTP payload security mechanisms, SRTP or other security mechanisms at RTP or lower layers can be used to provide integrity and source authentication between the splicer and the RTP receiver.7. Acknowledgments The following individuals have reviewed the earlier versions of this specification and provided very valuable comments: Colin Perkins, Magnus Westerlund, Roni Even, Tom Van Caenegem, Joerg Ott, David R. Oran, Cullen Jennings, Ali C. Begen, Charles Eckel, and Ning Zong.8. References8.1. Normative References [RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, "RTP: A Transport Protocol for Real-Time Applications", STD 64,RFC 3550, July 2003. [RFC4585] Ott, J., Wenger, S., Sato, N., Burmeister, C., and J. Rey, "Extended RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/AVPF)",RFC 4585, July 2006. [RFC6679] Westerlund, M., Johansson, I., Perkins, C., O'Hanlon, P., and K. Carlberg, "Explicit Congestion Notification (ECN) for RTP over UDP",RFC 6679, August 2012.8.2. Informative References [ISMACryp] Internet Streaming Media Alliance (ISMA), "ISMA Encryption and Authentication Specification 2.0", November 2007. [RFC3711] Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K. Norrman, "The Secure Real-time Transport Protocol (SRTP)",RFC 3711, March 2004. [RFC4301] Kent, S. and K. Seo, "Security Architecture for the Internet Protocol",RFC 4301, December 2005. [RFC5348] Floyd, S., Handley, M., Padhye, J., and J. Widmer, "TCP Friendly Rate Control (TFRC): Protocol Specification",RFC 5348, September 2008. [RFC5762] Perkins, C., "RTP and the Datagram Congestion Control Protocol (DCCP)",RFC 5762, April 2010.Xia Informational [Page 15]
RFC 6828 RTP Splicing January 2013 [RFC6347] Rescorla, E. and N. Modadugu, "Datagram Transport Layer Security Version 1.2",RFC 6347, January 2012. [SCTE30] Society of Cable Telecommunications Engineers (SCTE), "Digital Program Insertion Splicing API", 2009. [SCTE35] Society of Cable Telecommunications Engineers (SCTE), "Digital Program Insertion Cueing Message for Cable", 2011.Xia Informational [Page 16]
RFC 6828 RTP Splicing January 2013Appendix A. Why Mixer Is Chosen Both a translator and mixer can realize splicing by changing a set of RTP parameters. A translator has no SSRC; hence it is transparent to the RTP sender and receiver. Therefore, the RTP sender sees the full path to the receiver when the translator is passing its content. When a translator inserts the substitutive content, the RTP sender could get a report on the path up to the translator itself. Additionally, if splicing does not occur yet, the translator does not need to rewrite the RTP header, and the overhead on the translator can be avoided. If a mixer is used to do splicing, it can also allow the RTP sender to learn the situation of its content on the receiver or on the mixer just like the translator does, which is specified inSection 4.2. Compared to the translator, the mixer's outstanding benefit is that it is pretty straightforward to do with RTCP messages, for example, bit-rate adaptation to handle varying network conditions. But the translator needs more considerations, and its implementation is more complex. From the above analysis, both the translator and mixer have their own advantages: less overhead or less complexity on handling RTCP. After long and sophisticated discussions, the avtext WG members decided that they prefer less complexity rather than less overhead and are inclined to choose a mixer to do splicing. If one chooses a mixer as splicer, the overhead on the mixer must be taken into account even if the splicing has not occurred yet.Author's Address Jinwei Xia Huawei Software No.101 Nanjing, Yuhuatai District 210012 China Phone: +86-025-86622310 EMail: xiajinwei@huawei.comXia Informational [Page 17]
[8]ページ先頭