Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]
Obsoleted by:1706 EXPERIMENTAL
Network Working Group B. ManningRequest for Comments: 1637 Rice UniversityObsoletes:1348 R. ColellaCategory: Experimental NIST June 1994DNS NSAP Resource RecordsStatus of this Memo This memo defines an Experimental Protocol for the Internet community. This memo does not specify an Internet standard of any kind. Discussion and suggestions for improvement are requested. Distribution of this memo is unlimited.Abstract The Internet is moving towards the deployment of an OSI lower layers infrastructure. This infrastructure comprises the connectionless network protocol (CLNP) and supporting routing protocols. Also required as part of this infrastructure is support in the Domain Name System (DNS) for mapping between names and NSAP addresses. This document defines the format of one new Resource Record (RR) for the DNS for domain name-to-NSAP mapping. The RR may be used with any NSAP address format. This document supercedesRFC 1348. NSAP-to-name translation is accomplished through use of the PTR RR (see STD 13,RFC 1035 for a description of the PTR RR). This paper describes how PTR RRs are used to support this translation.Manning & Colella [Page 1]
RFC 1637 DNS NSAP RRs June 19941. Introduction The Internet is moving towards the deployment of an OSI lower layers infrastructure. This infrastructure comprises the connectionless network protocol (CLNP) [6] and supporting routing protocols. Also required as part of this infrastructure is support in the Domain Name System (DNS) [8] [9] for mapping between domain names and OSI Network Service Access Point (NSAP) addresses [7] [Note: NSAP and NSAP address are used interchangeably throughout this memo]. This document defines the format of one new Resource Record (RR) for the DNS for domain name-to-NSAP mapping. The RR may be used with any NSAP address format. NSAP-to-name translation is accomplished through use of the PTR RR (seeRFC 1035 for a description of the PTR RR). This paper describes how PTR RRs are used to support this translation. This memo assumes that the reader is familiar with the DNS. Some familiarity with NSAPs is useful; see [2] or [7] for additional information.2. Background The reason for defining DNS mappings for NSAPs is to support CLNP in the Internet. Debugging with CLNP ping and traceroute is becoming more difficult with only numeric NSAPs as the scale of deployment increases. Current debugging is supported by maintaining and exchanging a configuration file with name/NSAP mappings similar in function to hosts.txt. This suffers from the lack of a central coordinator for this file and also from the perspective of scaling. The former is the most serious short-term problem. Scaling of a hosts.txt-like solution has well-known long-term scaling difficiencies. A second reason for this work is the proposal to use CLNP as an alternative to IP: "TCP and UDP with Bigger Addresses (TUBA), A Simple Proposal for Internet Addressing and Routing" [1]. For this to be practical, the DNS must be capable of supporting CLNP addresses.3. Scope The methods defined in this paper are applicable to all NSAP formats. This includes support for the notion of a custom-defined NSAP format based on an AFI obtained by the IAB for use in the Internet. As a point of reference, there is a distinction between registration and publication of addresses. For IP addresses, the IANA is the rootManning & Colella [Page 2]
RFC 1637 DNS NSAP RRs June 1994 registration authority and the DNS a publication method. For NSAPs, addendum two of the network service definition, ISO8348/Ad2 [7] is the root registration authority and this memo defines how the DNS is used as a publication method.4. Structure of NSAPs NSAPs are hierarchically structured to allow distributed administration and efficient routing. Distributed administration permits subdelegated addressing authorities to, as allowed by the delegator, further structure the portion of the NSAP space under their delegated control. Accomodating this distributed authority requires that there be little or no a priori knowledge of the structure of NSAPs built into DNS resolvers and servers. For the purposes of this memo, NSAPs can be thought of as a tree of identifiers. The root of the tree is ISO8348/Ad2 [7], and has as its immediately registered subordinates the one-octet Authority and Format Identifiers (AFIs) defined there. The size of subsequently- defined fields depends on which branch of the tree is taken. The depth of the tree varies according to the authority responsible for defining subsequent fields. An example is the authority under which U.S. GOSIP defines NSAPs [3]. Under the AFI of 47, NIST (National Institute of Standards and Technology) obtained a value of 0005 (the AFI of 47 defines the next field as being two octets consisting of four BCD digits from the International Code Designator space [4]). NIST defined the subsequent fields in [3], as shown in Figure 1. The field immediately following 0005 is a format identifier for the rest of the U.S. GOSIP NSAP structure, with a hex value of 80. Following this is the three-octet field, values for which are allocated to network operators; the registration authority for this field is delegated to GSA (General Services Administration). The last octet of the NSAP is the NSelector (NSel). In practice, the NSAP minus the NSel identifies the CLNP protocol machine on a given system, and the NSel identifies the CLNP user. Since there can be more than one CLNP user (meaning multiple NSel values for a given "base" NSAP), the representation of the NSAP should be CLNP-user independent. To achieve this, an NSel value of zero shall be used with all NSAP values stored in the DNS. An NSAP with NSel=0 identifies the network layer itself. It is left to the application retrieving the NSAP to determine the appropriate value to use in that instance of communication.Manning & Colella [Page 3]
RFC 1637 DNS NSAP RRs June 1994 |--------------| | <-- IDP --> | |--------------|-------------------------------------| | AFI | IDI | <-- DSP --> | |-----|--------|-------------------------------------| | 47 | 0005 | DFI | AA |Rsvd | RD |Area | ID |Sel | |-----|--------|-----|----|-----|----|-----|----|----| octets | 1 | 2 | 1 | 3 | 2 | 2 | 2 | 6 | 1 | |-----|--------|-----|----|-----|----|-----|----|----| IDP Initial Domain Part AFI Authority and Format Identifier IDI Initial Domain Identifier DSP Domain Specific Part DFI DSP Format Identifier AA Administrative Authority Rsvd Reserved RD Routing Domain Identifier Area Area Identifier ID System Identifier SEL NSAP Selector Figure 1: GOSIP Version 2 NSAP structure. When CLNP is used to support TCP and UDP services, the NSel value used is the appropriate IP PROTO value as registered with the IANA. For "standard" OSI, the selection of NSel values is left as a matter of local administration. Administrators of systems that support the OSI transport protocol [5] in addition to TCP/UDP must select NSels for use by OSI Transport that do not conflict with the IP PROTO values. In the NSAP RRs in Master Files and in the printed text in this memo, NSAPs are often represented as a string of "."-separated hex values. The values correspond to convenient divisions of the NSAP to make it more readable. For example, the "."-separated fields might correspond to the NSAP fields as defined by the appropriate authority (ISOC, RARE, U.S. GOSIP, ANSI, etc.). The use of this notation is strictly for readability. The "."s do not appear in DNS packets and DNS servers can ignore them when reading Master Files. For example, a printable representation of the first four fields of a U.S. GOSIP NSAP might look like 47.0005.80.005a00Manning & Colella [Page 4]
RFC 1637 DNS NSAP RRs June 1994 and a full U.S. GOSIP NSAP might appear as 47.0005.80.005a00.0000.1000.0020.00800a123456.00. Other NSAP formats have different lengths and different administratively defined field widths to accomodate different requirements. For more information on NSAP formats in use seeRFC1629 [2].5. The NSAP RR The NSAP RR is defined with mnemonic "NSAP" and TYPE code 22 (decimal) and is used to map from domain names to NSAPs. Name-to-NSAP mapping in the DNS using the NSAP RR operates analogously to IP address lookup. A query is generated by the resolver requesting an NSAP RR for a provided domain name. NSAP RRs conform to the top level RR format and semantics as defined inSection 3.2.1 of RFC 1035. 1 1 1 1 1 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | | / / / NAME / | | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | TYPE = NSAP | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | CLASS = IN | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | TTL | | | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | RDLENGTH | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ / RDATA / / / +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ where: * NAME: an owner name, i.e., the name of the node to which this resource record pertains. * TYPE: two octets containing the NSAP RR TYPE code of 22 (decimal).Manning & Colella [Page 5]
RFC 1637 DNS NSAP RRs June 1994 * CLASS: two octets containing the RR IN CLASS code of 1. * TTL: a 32 bit signed integer that specifies the time interval in seconds that the resource record may be cached before the source of the information should again be consulted. Zero values are interpreted to mean that the RR can only be used for the transaction in progress, and should not be cached. For example, SOA records are always distributed with a zero TTL to prohibit caching. Zero values can also be used for extremely volatile data. * RDLENGTH: an unsigned 16 bit integer that specifies the length in octets of the RDATA field. * RDATA: a variable length string of octets containing the NSAP. The value is the binary encoding of the NSAP as it would appear in the CLNP source or destination address field. A typical example of such an NSAP (in hex) is shown below. For this NSAP, RDLENGTH is 20 (decimal); "."s have been omitted to emphasize that they don't appear in the DNS packets. 39840f80005a0000000001e13708002010726e005.1 Additional Section Processing [The specification in this section is necessary for completeness in describing name server support for TUBA. For the time being, name servers participating in TUBA demonstrations MAY ELECT to implement this behavior; it SHOULD NOT be the default behavior of name servers because the IPng sweepstakes are still outstanding and further consideration is required for truncation and other issues.]RFC 1035 describes the additional section processing (ASP) required when servers encounter NS records during query processing. FromSection 3.3.11, "NS RDATA format": NS records cause both the usual additional section processing to locate a type A record, and, when used in a referral, a special search of the zone in which they reside for glue information. For TUBA, identical ASP is required on type NSAP records to support servers and resolvers that use CLNP, either because of preference or because it is the only internetworking protocol available (i.e., in the absense of IPv4). Thus, NS records cause ASP which locates a type NSAP record in addition to a type A record. Both type A and NSAP records should be returned, if available.Manning & Colella [Page 6]
RFC 1637 DNS NSAP RRs June 19946. NSAP-to-name Mapping Using the PTR RR The PTR RR is defined inRFC 1035. This RR is typically used under the "IN-ADDR.ARPA" domain to map from IPv4 addresses to domain names. Similarly, the PTR RR is used to map from NSAPs to domain names under the "NSAP.INT" domain. A domain name is generated from the NSAP according to the rules described below. A query is sent by the resolver requesting a PTR RR for the provided domain name. A domain name is generated from an NSAP by reversing the hex nibbles of the NSAP, treating each nibble as a separate subdomain, and appending the top-level subdomain name "NSAP.INT" to it. For example, the domain name used in the reverse lookup for the NSAP 47.0005.80.005a00.0000.0001.e133.ffffff000162.00 would appear as 0.0.2.6.1.0.0.0.f.f.f.f.f.f.3.3.1.e.1.0.0.0.0.0.0.0.0.0.a.5.0.0. \ 0.8.5.0.0.0.7.4.NSAP.INT. [Implementation note: For sanity's sake user interfaces should be designed to allow users to enter NSAPs using their natural order, i.e., as they are typically written on paper. Also, arbitrary "."s should be allowed (and ignored) on input.]7. Master File Format The format of NSAP RRs (and NSAP-related PTR RRs) in Master Files conforms toSection 5, "Master Files," ofRFC 1035. Below are examples of the use of these RRs in Master Files to support name-to- NSAP and NSAP-to-name mapping. The NSAP RR introduces a new hex string format for the RDATA field. The format is "0x" (i.e., a zero followed by an 'x' character) followed by a variable length string of hex characters (0 to 9, a to f). The hex string is case-insensitive. "."s (i.e., periods) may be inserted in the hex string anywhere after the "0x" for readability. The "."s have no significance other than for readability and are not propagated in the protocol (e.g., queries or zone transfers).Manning & Colella [Page 7]
RFC 1637 DNS NSAP RRs June 1994 ;;;;;; ;;;;;; Master File for domain nsap.nist.gov. ;;;;;; @ IN SOA emu.ncsl.nist.gov. root.emu.ncsl.nist.gov. ( 1994041800 ; Serial - date 1800 ; Refresh - 30 minutes 300 ; Retry - 5 minutes 604800 ; Expire - 7 days 3600 ) ; Minimum - 1 hour IN NS emu.ncsl.nist.gov. IN NS tuba.nsap.lanl.gov. ; ; $ORIGIN nsap.nist.gov. ; ; hosts ; bsdi1 IN NSAP 0x47.0005.80.005a00.0000.0001.e133.ffffff000161.00 IN A 129.6.224.161 IN HINFO PC_486 BSDi1.1(TUBA) ; bsdi2 IN NSAP 0x47.0005.80.005a00.0000.0001.e133.ffffff000162.00 IN A 129.6.224.162 IN HINFO PC_486 BSDi1.1(TUBA) ; cursive IN NSAP 0x47.0005.80.005a00.0000.0001.e133.ffffff000171.00 IN A 129.6.224.171 IN HINFO PC_386 DOS_5.0/NCSA_Telnet(TUBA) ; infidel IN NSAP 0x47.0005.80.005a00.0000.0001.e133.ffffff000164.00 IN A 129.6.55.164 IN HINFO PC/486 BSDi1.0(TUBA) ; ; routers ; cisco1 IN NSAP 0x47.0005.80.005a00.0000.0001.e133.aaaaaa000151.00 IN A 129.6.224.151 IN A 129.6.225.151 IN A 129.6.229.151 ; 3com1 IN NSAP 0x47.0005.80.005a00.0000.0001.e133.aaaaaa000111.00 IN A 129.6.224.111 IN A 129.6.225.111 IN A 129.6.228.111Manning & Colella [Page 8]
RFC 1637 DNS NSAP RRs June 1994 ;;;;;; ;;;;;; Master File for reverse mapping of NSAPs under the ;;;;;; NSAP prefix: ;;;;;; ;;;;;; 47.0005.80.005a00.0000.0001.e133 ;;;;;; @ IN SOA emu.ncsl.nist.gov. root.emu.ncsl.nist.gov. ( 1994041800 ; Serial - date 1800 ; Refresh - 30 minutes 300 ; Retry - 5 minutes 604800 ; Expire - 7 days 3600 ) ; Minimum - 1 hour IN NS emu.ncsl.nist.gov. IN NS tuba.nsap.lanl.gov. ; ; $ORIGIN 3.3.1.e.1.0.0.0.0.0.0.0.0.0.a.5.0.0.0.8.5.0.0.0.7.4.NSAP.INT. ; 0.0.1.6.1.0.0.0.f.f.f.f.f.f IN PTR bsdi1.nsap.nist.gov. ; 0.0.2.6.1.0.0.0.f.f.f.f.f.f IN PTR bsdi2.nsap.nist.gov. ; 0.0.1.7.1.0.0.0.f.f.f.f.f.f IN PTR cursive.nsap.nist.gov. ; 0.0.4.6.1.0.0.0.f.f.f.f.f.f IN PTR infidel.nsap.nist.gov. ; 0.0.1.5.1.0.0.0.a.a.a.a.a.a IN PTR cisco1.nsap.nist.gov. ; 0.0.1.1.1.0.0.0.a.a.a.a.a.a IN PTR 3com1.nsap.nist.gov.8. Security Considerations Security issues are not discussed in this memo.Manning & Colella [Page 9]
RFC 1637 DNS NSAP RRs June 19949. Authors' Addresses Bill Manning Rice University -- ONCS P.O. Box 1892 6100 South Main Houston, Texas 77251-1892 USA Phone: +1.713.285.5415 EMail: bmanning@rice.edu Richard Colella National Institute of Standards and Technology Technology/B217 Gaithersburg, MD 20899 USA Phone: +1 301-975-3627 Fax: +1 301 590-0932 EMail: colella@nist.gov10. References [1] Callon R., "TCP and UDP with Bigger Addresses (TUBA), A Simple Proposal for Internet Addressing and Routing",RFC 1347, DEC, June 1992. [2] Colella, R., Gardner, E., Callon, R., and Y. Rekhter, "Guidelines for OSI NSAP Allocation inh the Internet",RFC 1629, NIST, Wellfleet, Mitre, T.J. Watson Research Center, IBM Corp., May 1994. [3] GOSIP Advanced Requirements Group. Government Open Systems Interconnection Profile (GOSIP) Version 2. Federal Information Processing Standard 146-1, U.S. Department of Commerce, National Institute of Standards and Technology, Gaithersburg, MD, April 1991. [4] ISO/IEC. Data interchange - structures for the identification of organization. International Standard 6523, ISO/IEC JTC 1, Switzerland, 1984. [5] ISO/IEC. Connection oriented transport protocol specification. International Standard 8073, ISO/IEC JTC 1, Switzerland, 1986.Manning & Colella [Page 10]
RFC 1637 DNS NSAP RRs June 1994 [6] ISO/IEC. Protocol for Providing the Connectionless-mode Network Service. International Standard 8473, ISO/IEC JTC 1, Switzerland, 1986. [7] ISO/IEC. Information Processing Systems -- Data Communications -- Network Service Definition Addendum 2: Network Layer Addressing. International Standard 8348/Addendum 2, ISO/IEC JTC 1, Switzerland, 1988. [8] Mockapetris, P., "Domain Names -- Concepts and Facilities", STD 13,RFC 1034, USC/Information Sciences Institute, November 1987. [9] Mockapetris, P., "Domain Names -- Implementation and Specification", STD 13,RFC 1035, USC/Information Sciences Institute, November 1987.Manning & Colella [Page 11]
[8]ページ先頭