Device Tree¶

GPIOs can easily be mapped to devices and functions in the device tree. Theexact way to do it depends on the GPIO controller providing the GPIOs, see thedevice tree bindings for your controller.

GPIOs mappings are defined in the consumer device’s node, in a property named<function>-gpios, where <function> is the function the driver will requestthroughgpiod_get(). For example:

foo_device {        compatible = "acme,foo";        ...        led-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>, /* red */                    <&gpio 16 GPIO_ACTIVE_HIGH>, /* green */                    <&gpio 17 GPIO_ACTIVE_HIGH>; /* blue */        power-gpios = <&gpio 1 GPIO_ACTIVE_LOW>;};

Properties named <function>-gpio are also considered valid and old bindings useit but are only supported for compatibility reasons and should not be used fornewer bindings since it has been deprecated.

This property will make GPIOs 15, 16 and 17 available to the driver under the“led” function, and GPIO 1 as the “power” GPIO:

struct gpio_desc *red, *green, *blue, *power;red = gpiod_get_index(dev, "led", 0, GPIOD_OUT_HIGH);green = gpiod_get_index(dev, "led", 1, GPIOD_OUT_HIGH);blue = gpiod_get_index(dev, "led", 2, GPIOD_OUT_HIGH);power = gpiod_get(dev, "power", GPIOD_OUT_HIGH);

The led GPIOs will be active high, while the power GPIO will be active low (i.e.gpiod_is_active_low(power) will be true).

The second parameter of thegpiod_get() functions, the con_id string, has to bethe <function>-prefix of the GPIO suffixes (“gpios” or “gpio”, automaticallylooked up by the gpiod functions internally) used in the device tree. With above“led-gpios” example, use the prefix without the “-” as con_id parameter: “led”.

Internally, the GPIO subsystem prefixes the GPIO suffix (“gpios” or “gpio”)with the string passed in con_id to get the resulting string(snprintf(..."%s-%s",con_id,gpio_suffixes[]).

ACPI¶

ACPI also supports function names for GPIOs in a similar fashion to DT.The above DT example can be converted to an equivalent ACPI descriptionwith the help of _DSD (Device Specific Data), introduced in ACPI 5.1:

Device (FOO) {        Name (_CRS, ResourceTemplate () {                GpioIo (Exclusive, ..., IoRestrictionOutputOnly,                        "\\_SB.GPI0") {15} // red                GpioIo (Exclusive, ..., IoRestrictionOutputOnly,                        "\\_SB.GPI0") {16} // green                GpioIo (Exclusive, ..., IoRestrictionOutputOnly,                        "\\_SB.GPI0") {17} // blue                GpioIo (Exclusive, ..., IoRestrictionOutputOnly,                        "\\_SB.GPI0") {1} // power        })        Name (_DSD, Package () {                ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),                Package () {                        Package () {                                "led-gpios",                                Package () {                                        ^FOO, 0, 0, 1,                                        ^FOO, 1, 0, 1,                                        ^FOO, 2, 0, 1,                                }                        },                        Package () {                                "power-gpios",                                Package () {^FOO, 3, 0, 0},                        },                }        })}

For more information about the ACPI GPIO bindings seeDocumentation/firmware-guide/acpi/gpio-properties.rst.

Platform Data¶

Finally, GPIOs can be bound to devices and functions using platform data. Boardfiles that desire to do so need to include the following header:

#include <linux/gpio/machine.h>

GPIOs are mapped by the means of tables of lookups, containing instances of thegpiod_lookup structure. Two macros are defined to help declaring such mappings:

GPIO_LOOKUP(key, chip_hwnum, con_id, flags)GPIO_LOOKUP_IDX(key, chip_hwnum, con_id, idx, flags)

where

• key is either the label of the gpiod_chip instance providing the GPIO, orthe GPIO line name
• chip_hwnum is the hardware number of the GPIO within the chip, or U16_MAXto indicate that key is a GPIO line name

• con_id is the name of the GPIO function from the device point of view. It

  can be NULL, in which case it will match any function.

• idx is the index of the GPIO within the function.

• flags is defined to specify the following properties:

  • GPIO_ACTIVE_HIGH - GPIO line is active high
  • GPIO_ACTIVE_LOW - GPIO line is active low
  • GPIO_OPEN_DRAIN - GPIO line is set up as open drain
  • GPIO_OPEN_SOURCE - GPIO line is set up as open source

  • GPIO_PERSISTENT - GPIO line is persistent during

    suspend/resume and maintains its value

  • GPIO_TRANSITORY - GPIO line is transitory and may loose its

    electrical state during suspend/resume

In the future, these flags might be extended to support more properties.

Note that:

1. GPIO line names are not guaranteed to be globally unique, so the firstmatch found will be used.
2. GPIO_LOOKUP() is just a shortcut to GPIO_LOOKUP_IDX() where idx = 0.

A lookup table can then be defined as follows, with an empty entry defining itsend. The ‘dev_id’ field of the table is the identifier of the device that willmake use of these GPIOs. It can be NULL, in which case it will be matched forcalls togpiod_get() with a NULL device.

structgpiod_lookup_tablegpios_table={.dev_id="foo.0",.table={GPIO_LOOKUP_IDX("gpio.0",15,"led",0,GPIO_ACTIVE_HIGH),GPIO_LOOKUP_IDX("gpio.0",16,"led",1,GPIO_ACTIVE_HIGH),GPIO_LOOKUP_IDX("gpio.0",17,"led",2,GPIO_ACTIVE_HIGH),GPIO_LOOKUP("gpio.0",1,"power",GPIO_ACTIVE_LOW),{},},};

And the table can be added by the board code as follows:

gpiod_add_lookup_table(&gpios_table);

The driver controlling “foo.0” will then be able to obtain its GPIOs as follows:

struct gpio_desc *red, *green, *blue, *power;red = gpiod_get_index(dev, "led", 0, GPIOD_OUT_HIGH);green = gpiod_get_index(dev, "led", 1, GPIOD_OUT_HIGH);blue = gpiod_get_index(dev, "led", 2, GPIOD_OUT_HIGH);power = gpiod_get(dev, "power", GPIOD_OUT_HIGH);

Since the “led” GPIOs are mapped as active-high, this example will switch theirsignals to 1, i.e. enabling the LEDs. And for the “power” GPIO, which is mappedas active-low, its actual signal will be 0 after this code. Contrary to thelegacy integer GPIO interface, the active-low property is handled duringmapping and is thus transparent to GPIO consumers.

A set of functions such asgpiod_set_value() is available to work withthe new descriptor-oriented interface.

Boards using platform data can also hog GPIO lines by defining GPIO hog tables.

structgpiod_hoggpio_hog_table[]={GPIO_HOG("gpio.0",10,"foo",GPIO_ACTIVE_LOW,GPIOD_OUT_HIGH),{}};

And the table can be added to the board code as follows:

gpiod_add_hogs(gpio_hog_table);

The line will be hogged as soon as the gpiochip is created or - in case thechip was created earlier - when the hog table is registered.

Arrays of pins¶

In addition to requesting pins belonging to a function one by one, a device mayalso request an array of pins assigned to the function. The way those pins aremapped to the device determines if the array qualifies for fast bitmapprocessing. If yes, a bitmap is passed over get/set array functions directlybetween a caller and a respective .get/set_multiple() callback of a GPIO chip.

In order to qualify for fast bitmap processing, the array must meet thefollowing requirements:

• pin hardware number of array member 0 must also be 0,
• pin hardware numbers of consecutive array members which belong to the samechip as member 0 does must also match their array indexes.

Otherwise fast bitmap processing path is not used in order to avoid consecutivepins which belong to the same chip but are not in hardware order being processedseparately.

If the array applies for fast bitmap processing path, pins which belong todifferent chips than member 0 does, as well as those with indexes different fromtheir hardware pin numbers, are excluded from the fast path, both input andoutput. Moreover, open drain and open source pins are excluded from fast bitmapoutput processing.