Important

BUGGY IDE CHIPSETS CAN CORRUPT DATA!!

PCI versions of the CMD640 and RZ1000 interfaces are now detectedautomatically at startup when PCI BIOS support is configured.

Linux disables the “prefetch” (“readahead”) mode of the RZ1000to prevent data corruption possible due to hardware design flaws.

For the CMD640, linux disables “IRQ unmasking” (hdparm -u1) on anydrive for which the “prefetch” mode of the CMD640 is turned on.If “prefetch” is disabled (hdparm -p8), then “IRQ unmasking” can beused again.

For the CMD640, linux disables “32bit I/O” (hdparm -c1) on any drivefor which the “prefetch” mode of the CMD640 is turned off.If “prefetch” is enabled (hdparm -p9), then “32bit I/O” can beused again.

The CMD640 is also used on some Vesa Local Bus (VLB) cards, and isNOTautomatically detected by Linux. For safe, reliable operation with suchinterfaces, oneMUST use the “cmd640.probe_vlb” kernel option.

Use of the “serialize” option is no longer necessary.

Common pitfalls¶

• 40-conductor IDE cables are capable of transferring data in DMA modes up toudma2, but no faster.
• If possible devices should be attached to separate channels if they areavailable. Typically the disk on the first and CD-ROM on the second.
• If you mix devices on the same cable, please consider using similar devicesin respect of the data transfer mode they support.
• Even better try to stick to the same vendor and device type on the samecable.

This is the multiple IDE interface driver, as evolved from hd.c¶

It supports up to 9 IDE interfaces per default, on one or more IRQs (usually14 & 15). There can be up to two drives per interface, as per the ATA-6 spec.:

Primary:    ide0, port 0x1f0; major=3;  hda is minor=0; hdb is minor=64Secondary:  ide1, port 0x170; major=22; hdc is minor=0; hdd is minor=64Tertiary:   ide2, port 0x1e8; major=33; hde is minor=0; hdf is minor=64Quaternary: ide3, port 0x168; major=34; hdg is minor=0; hdh is minor=64fifth..     ide4, usually PCI, probedsixth..     ide5, usually PCI, probed

To access devices on interfaces > ide0, device entries please make sure thatdevice files for them are present in /dev. If not, please create suchentries, by using /dev/MAKEDEV.

This driver automatically probes for most IDE interfaces (including all PCIones), for the drives/geometries attached to those interfaces, and for the IRQlines being used by the interfaces (normally 14, 15 for ide0/ide1).

Any number of interfaces may share a single IRQ if necessary, at a slightperformance penalty, whether on separate cards or a single VLB card.The IDE driver automatically detects and handles this. However, this mayor may not be harmful to your hardware.. two or more cards driving the same IRQcan potentially burn each other’s bus driver, though in practice thisseldom occurs. Be careful, and if in doubt, don’t do it!

Drives are normally found by auto-probing and/or examining the CMOS/BIOS data.For really weird situations, the apparent (fdisk) geometry can also be specifiedon the kernel “command line” using LILO. The format of such lines is:

ide_core.chs=[interface_number.device_number]:cyls,heads,sects

or:

ide_core.cdrom=[interface_number.device_number]

For example:

ide_core.chs=1.0:1050,32,64  ide_core.cdrom=1.1

The results of successful auto-probing may override the physical geometry/irqspecified, though the “original” geometry may be retained as the “logical”geometry for partitioning purposes (fdisk).

If the auto-probing during boot time confuses a drive (ie. the drive workswith hd.c but not with ide.c), then an command line option may be specifiedfor each drive for which you’d like the drive to skip the hardwareprobe/identification sequence. For example:

ide_core.noprobe=0.1

or:

ide_core.chs=1.0:768,16,32ide_core.noprobe=1.0

Note that when only one IDE device is attached to an interface, it should bejumpered as “single” or “master”,not “slave”. Many folks have had“trouble” with cdroms because of this requirement, so the driver now probesfor both units, though success is more likely when the drive is jumperedcorrectly.

Courtesy of Scott Snyder and others, the driver supports ATAPI cdrom drivessuch as the NEC-260 and the new MITSUMI triple/quad speed drives.Such drives will be identified at boot time, just like a hard disk.

If for some reason your cdrom drive isnot found at boot time, you can forcethe probe to look harder by supplying a kernel command line parametervia LILO, such as::

ide_core.cdrom=1.0      /* "master" on second interface (hdc) */

or:

ide_core.cdrom=1.1      /* "slave" on second interface (hdd) */

For example, a GW2000 system might have a hard drive on the primaryinterface (/dev/hda) and an IDE cdrom drive on the secondary interface(/dev/hdc). To mount a CD in the cdrom drive, one would use something like:

ln -sf /dev/hdc /dev/cdrommkdir /mnt/cdrommount /dev/cdrom /mnt/cdrom -t iso9660 -o ro

If, after doing all of the above, mount doesn’t work and you seeerrors from the driver (with dmesg) complaining aboutstatus=0xff,this means that the hardware is not responding to the driver’s attemptsto read it. One of the following is probably the problem:

• Your hardware is broken.
• You are using the wrong address for the device, or you have thedrive jumpered wrong. Review the configuration instructions above.
• Your IDE controller requires some nonstandard initialization sequencebefore it will work properly. If this is the case, there will oftenbe a separate MS-DOS driver just for the controller. IDE interfaceson sound cards usually fall into this category. Such configurationscan often be made to work by first booting MS-DOS, loading theappropriate drivers, and then warm-booting linux (without poweringoff). This can be automated using loadlin in the MS-DOS autoexec.

If you always get timeout errors, interrupts from the drive are probablynot making it to the host. Check how you have the hardware jumperedand make sure it matches what the driver expects (see the configurationinstructions above). If you have a PCI system, also check the BIOSsetup; I’ve had one report of a system which was shipped with IRQ 15disabled by the BIOS.

The kernel is able to execute binaries directly off of the cdrom,provided it is mounted with the default block size of 1024 (as above).

Please pass on any feedback on any of this stuff to the maintainer,whose address can be found in linux/MAINTAINERS.

The IDE driver is modularized. The high level disk/CD-ROM/tape/floppydrivers can always be compiled as loadable modules, the chipset driverscan only be compiled into the kernel, and the core code (ide.c) can becompiled as a loadable module provided no chipset support is needed.

When using ide.c as a module in combination with kmod, add:

alias block-major-3 ide-probe

to a configuration file in /etc/modprobe.d/.

When ide.c is used as a module, you can pass command line parameters to thedriver using the “options=” keyword to insmod, while replacing any ‘,’ with‘;’.

Summary of ide driver parameters for kernel command line¶

For legacy IDE VLB host drivers (ali14xx/dtc2278/ht6560b/qd65xx/umc8672)you need to explicitly enable probing by using “probe” kernel parameter,i.e. to enable probing for ALI M14xx chipsets (ali14xx host driver) use:

• “ali14xx.probe” boot option when ali14xx driver is built-in the kernel
• “probe” module parameter when ali14xx driver is compiled as module(“modprobe ali14xx probe”)

Also for legacy CMD640 host driver (cmd640) you need to use “probe_vlb”kernel paremeter to enable probing for VLB version of the chipset (PCI onesare detected automatically).

You also need to use “probe” kernel parameter for ide-4drives driver(support for IDE generic chipset with four drives on one port).

To enable support for IDE doublers on Amiga use “doubler” kernel parameterfor gayle host driver (i.e. “gayle.doubler” if the driver is built-in).

To force ignoring cable detection (this should be needed only if you’re usingshort 40-wires cable which cannot be automatically detected - if this is nota case please report it as a bug instead) use “ignore_cable” kernel parameter:

• “ide_core.ignore_cable=[interface_number]” boot option if IDE is built-in(i.e. “ide_core.ignore_cable=1” to force ignoring cable for “ide1”)
• “ignore_cable=[interface_number]” module parameter (for ide_core module)if IDE is compiled as module

Other kernel parameters for ide_core are:

• “nodma=[interface_number.device_number]” to disallow DMA for a device
• “noflush=[interface_number.device_number]” to disable flush requests
• “nohpa=[interface_number.device_number]” to disable Host Protected Area
• “noprobe=[interface_number.device_number]” to skip probing
• “nowerr=[interface_number.device_number]” to ignore the WRERR_STAT bit
• “cdrom=[interface_number.device_number]” to force device as a CD-ROM
• “chs=[interface_number.device_number]” to force device as a disk (using CHS)

Some Terminology¶

IDE

Integrated Drive Electronics, meaning that each drive has a built-incontroller, which is why an “IDE interface card” is not a “controller card”.

ATA

AT (the old IBM 286 computer) Attachment Interface, a draft AmericanNational Standard for connecting hard drives to PCs. This is the officialname for “IDE”.

The latest standards define some enhancements, known as the ATA-6 spec,which grew out of vendor-specific “Enhanced IDE” (EIDE) implementations.

ATAPI

ATA Packet Interface, a new protocol for controlling the drives,similar to SCSI protocols, created at the same time as the ATA2 standard.ATAPI is currently used for controlling CDROM, TAPE and FLOPPY (ZIP orLS120/240) devices, removable R/W cartridges, and for high capacity hard diskdrives.

mlord@pobox.com

Wed Apr 17 22:52:44 CEST 2002 edited by Marcin Dalecki, the currentmaintainer.

Wed Aug 20 22:31:29 CEST 2003 updated ide boot options to current ide.ccomments at 2.6.0-test4 time. Maciej Soltysiak <solt@dns.toxicfilms.tv>