Mount Options¶

When mounting an XFS filesystem, the following options are accepted.

allocsize=size

Sets the buffered I/O end-of-file preallocation size whendoing delayed allocation writeout (default size is 64KiB).Valid values for this option are page size (typically 4KiB)through to 1GiB, inclusive, in power-of-2 increments.

The default behaviour is for dynamic end-of-filepreallocation size, which uses a set of heuristics tooptimise the preallocation size based on the currentallocation patterns within the file and the access patternsto the file. Specifying a fixedallocsize value turns offthe dynamic behaviour.

attr2 or noattr2

The options enable/disable an “opportunistic” improvement tobe made in the way inline extended attributes are storedon-disk. When the new form is used for the first time whenattr2 is selected (either when setting or removing extendedattributes) the on-disk superblock feature bit field will beupdated to reflect this format being in use.

The default behaviour is determined by the on-disk featurebit indicating thatattr2 behaviour is active. If eithermount option is set, then that becomes the new default usedby the filesystem.

CRC enabled filesystems always use theattr2 format, and sowill reject thenoattr2 mount option if it is set.

discard or nodiscard (default)

Enable/disable the issuing of commands to let the blockdevice reclaim space freed by the filesystem. This isuseful for SSD devices, thinly provisioned LUNs and virtualmachine images, but may have a performance impact.

Note: It is currently recommended that you use thefstrimapplication todiscard unused blocks rather than thediscardmount option because the performance impact of this optionis quite severe.

grpid/bsdgroups or nogrpid/sysvgroups (default)

These options define what group ID a newly created filegets. Whengrpid is set, it takes the group ID of thedirectory in which it is created; otherwise it takes thefsgid of the current process, unless the directory has thesetgid bit set, in which case it takes thegid from theparent directory, and also gets thesetgid bit set if it isa directory itself.

filestreams

Make the data allocator use the filestreams allocation modeacross the entire filesystem rather than just on directoriesconfigured to use it.

ikeep or noikeep (default)

Whenikeep is specified, XFS does not delete empty inodeclusters and keeps them around on disk. Whennoikeep isspecified, empty inode clusters are returned to the freespace pool.

inode32 or inode64 (default)

Wheninode32 is specified, it indicates that XFS limitsinode creation to locations which will not result in inodenumbers with more than 32 bits of significance.

Wheninode64 is specified, it indicates that XFS is allowedto create inodes at any location in the filesystem,including those which will result in inode numbers occupyingmore than 32 bits of significance.

inode32 is provided for backwards compatibility with oldersystems and applications, since 64 bits inode numbers mightcause problems for some applications that cannot handlelarge inode numbers. If applications are in use which donot handle inode numbers bigger than 32 bits, theinode32option should be specified.

largeio or nolargeio (default)

Ifnolargeio is specified, the optimal I/O reported inst_blksize bystat(2) will be as small as possible to allowuser applications to avoid inefficient read/modify/writeI/O. This is typically the page size of the machine, asthis is the granularity of the page cache.

Iflargeio is specified, a filesystem that was created with aswidth specified will return theswidth value (in bytes)inst_blksize. If the filesystem does not have aswidthspecified but does specify anallocsize thenallocsize(in bytes) will be returned instead. Otherwise the behaviouris the same as ifnolargeio was specified.

logbufs=value

Set the number of in-memory log buffers. Valid numbersrange from 2-8 inclusive.

The default value is 8 buffers.

If the memory cost of 8 log buffers is too high on smallsystems, then it may be reduced at some cost to performanceon metadata intensive workloads. Thelogbsize option belowcontrols the size of each buffer and so is also relevant tothis case.

logbsize=value

Set the size of each in-memory log buffer. The size may bespecified in bytes, or in kilobytes with a “k” suffix.Valid sizes for version 1 and version 2 logs are 16384 (16k)and 32768 (32k). Valid sizes for version 2 logs alsoinclude 65536 (64k), 131072 (128k) and 262144 (256k). Thelogbsize must be an integer multiple of the logstripe unit configured atmkfs(8) time.

The default value for version 1 logs is 32768, while thedefault value for version 2 logs is MAX(32768, log_sunit).

logdev=device and rtdev=device

Use an external log (metadata journal) and/or real-time device.An XFS filesystem has up to three parts: a data section, a logsection, and a real-time section. The real-time section isoptional, and the log section can be separate from the datasection or contained within it.

noalign

Data allocations will not be aligned at stripe unitboundaries. This is only relevant to filesystems createdwith non-zero data alignment parameters (sunit,swidth) bymkfs(8).

norecovery

The filesystem will be mounted without running log recovery.If the filesystem was not cleanly unmounted, it is likely tobe inconsistent when mounted innorecovery mode.Some files or directories may not be accessible because of this.Filesystems mountednorecovery must be mounted read-only orthe mount will fail.

nouuid

Don’t check for double mounted file systems using the filesystemuuid. This is useful to mount LVM snapshot volumes,and often used in combination withnorecovery for mountingread-only snapshots.

noquota

Forcibly turns off all quota accounting and enforcementwithin the filesystem.

uquota/usrquota/uqnoenforce/quota

User disk quota accounting enabled, and limits (optionally)enforced. Refer toxfs_quota(8) for further details.

gquota/grpquota/gqnoenforce

Group disk quota accounting enabled and limits (optionally)enforced. Refer toxfs_quota(8) for further details.

pquota/prjquota/pqnoenforce

Project disk quota accounting enabled and limits (optionally)enforced. Refer toxfs_quota(8) for further details.

sunit=value and swidth=value

Used to specify the stripe unit and width for a RAID deviceor a stripe volume. “value” must be specified in 512-byteblock units. These options are only relevant to filesystemsthat were created with non-zero data alignment parameters.

Thesunit andswidth parameters specified must be compatiblewith the existing filesystem alignment characteristics. Ingeneral, that means the only valid changes tosunit areincreasing it by a power-of-2 multiple. Validswidth valuesare any integer multiple of a validsunit value.

Typically the only time these mount options are necessary ifafter an underlying RAID device has had it’s geometrymodified, such as adding a new disk to a RAID5 lun andreshaping it.

swalloc

Data allocations will be rounded up to stripe width boundarieswhen the current end of file is being extended and the filesize is larger than the stripe width size.

wsync

When specified, all filesystem namespace operations areexecuted synchronously. This ensures that when the namespaceoperation (create, unlink, etc) completes, the change to thenamespace is on stable storage. This is useful in HA setupswhere failover must not result in clients seeinginconsistent namespace presentation during or after afailover event.

Deprecated Mount Options¶

Removed Mount Options¶

sysctls¶

The following sysctls are available for the XFS filesystem:

fs.xfs.stats_clear (Min: 0 Default: 0 Max: 1)

Setting this to “1” clears accumulated XFS statisticsin /proc/fs/xfs/stat. It then immediately resets to “0”.

fs.xfs.xfssyncd_centisecs (Min: 100 Default: 3000 Max: 720000)

The interval at which the filesystem flushes metadataout to disk and runs internal cache cleanup routines.

fs.xfs.filestream_centisecs (Min: 1 Default: 3000 Max: 360000)

The interval at which the filesystem ages filestreams cachereferences and returns timed-out AGs back to the free streampool.

fs.xfs.speculative_prealloc_lifetime

(Units: seconds Min: 1 Default: 300 Max: 86400)The interval at which the background scanning for inodeswith unused speculative preallocation runs. The scanremoves unused preallocation from clean inodes and releasesthe unused space back to the free pool.

fs.xfs.error_level (Min: 0 Default: 3 Max: 11)

A volume knob for error reporting when internal errors occur.This will generate detailed messages & backtraces for filesystemshutdowns, for example. Current threshold values are:

XFS_ERRLEVEL_OFF: 0XFS_ERRLEVEL_LOW: 1XFS_ERRLEVEL_HIGH: 5

fs.xfs.panic_mask (Min: 0 Default: 0 Max: 256)

Causes certain error conditions to call BUG(). Value is a bitmask;OR together the tags which represent errors which should cause panics:

XFS_NO_PTAG 0XFS_PTAG_IFLUSH 0x00000001XFS_PTAG_LOGRES 0x00000002XFS_PTAG_AILDELETE 0x00000004XFS_PTAG_ERROR_REPORT 0x00000008XFS_PTAG_SHUTDOWN_CORRUPT 0x00000010XFS_PTAG_SHUTDOWN_IOERROR 0x00000020XFS_PTAG_SHUTDOWN_LOGERROR 0x00000040XFS_PTAG_FSBLOCK_ZERO 0x00000080XFS_PTAG_VERIFIER_ERROR 0x00000100

This option is intended for debugging only.

fs.xfs.irix_symlink_mode (Min: 0 Default: 0 Max: 1)

Controls whether symlinks are created with mode 0777 (default)or whether their mode is affected by the umask (irix mode).

fs.xfs.irix_sgid_inherit (Min: 0 Default: 0 Max: 1)

Controls files created in SGID directories.If the group ID of the new file does not match the effective groupID or one of the supplementary group IDs of the parent dir, theISGID bit is cleared if the irix_sgid_inherit compatibility sysctlis set.

fs.xfs.inherit_sync (Min: 0 Default: 1 Max: 1)

Setting this to “1” will cause the “sync” flag setby thexfs_io(8) chattr command on a directory to beinherited by files in that directory.

fs.xfs.inherit_nodump (Min: 0 Default: 1 Max: 1)

Setting this to “1” will cause the “nodump” flag setby thexfs_io(8) chattr command on a directory to beinherited by files in that directory.

fs.xfs.inherit_noatime (Min: 0 Default: 1 Max: 1)

Setting this to “1” will cause the “noatime” flag setby thexfs_io(8) chattr command on a directory to beinherited by files in that directory.

fs.xfs.inherit_nosymlinks (Min: 0 Default: 1 Max: 1)

Setting this to “1” will cause the “nosymlinks” flag setby thexfs_io(8) chattr command on a directory to beinherited by files in that directory.

fs.xfs.inherit_nodefrag (Min: 0 Default: 1 Max: 1)

Setting this to “1” will cause the “nodefrag” flag setby thexfs_io(8) chattr command on a directory to beinherited by files in that directory.

fs.xfs.rotorstep (Min: 1 Default: 1 Max: 256)

In “inode32” allocation mode, this option determines how manyfiles the allocator attempts to allocate in the same allocationgroup before moving to the next allocation group. The intentis to control the rate at which the allocator moves betweenallocation groups when allocating extents for new files.

Deprecated Sysctls¶

None at present.

Removed Sysctls¶

Error handling¶

XFS can act differently according to the type of error found during itsoperation. The implementation introduces the following concepts to the errorhandler:

-failure speed:

Defines how fast XFS should propagate an error upwards when a specificerror is found during the filesystem operation. It can propagateimmediately, after a defined number of retries, after a set time period,or simply retry forever.

-error classes:

Specifies the subsystem the error configuration will apply to, such asmetadata IO or memory allocation. Different subsystems will havedifferent error handlers for which behaviour can be configured.

-error handlers:

Defines the behavior for a specific error.

The filesystem behavior during an error can be set viasysfs files. Eacherror handler works independently - the first condition met by an error handlerfor a specific class will cause the error to be propagated rather than reset andretried.

The action taken by the filesystem when the error is propagated is contextdependent - it may cause a shut down in the case of an unrecoverable error,it may be reported back to userspace, or it may even be ignored becausethere’s nothing useful we can with the error or anyone we can report it to (e.g.during unmount).

The configuration files are organized into the following hierarchy for eachmounted filesystem:

/sys/fs/xfs/<dev>/error/<class>/<error>/

Where:

<dev>

The short device name of the mounted filesystem. This is the same devicename that shows up in XFS kernel error messages as “XFS(<dev>): …”

<class>

The subsystem the error configuration belongs to. As of 4.9, the definedclasses are:

• “metadata”: applies metadata buffer write IO

<error>

The individual error handler configurations.

Each filesystem has “global” error configuration options defined in their toplevel directory:

/sys/fs/xfs/<dev>/error/

fail_at_unmount (Min: 0 Default: 1 Max: 1)

Defines the filesystem error behavior at unmount time.

If set to a value of 1, XFS will override all other error configurationsduring unmount and replace them with “immediate fail” characteristics.i.e. no retries, no retry timeout. This will always allow unmount tosucceed when there are persistent errors present.

If set to 0, the configured retry behaviour will continue until allretries and/or timeouts have been exhausted. This will delay unmountcompletion when there are persistent errors, and it may prevent thefilesystem from ever unmounting fully in the case of “retry forever”handler configurations.

Note: there is no guarantee that fail_at_unmount can be set while anunmount is in progress. It is possible that thesysfs entries areremoved by the unmounting filesystem before a “retry forever” errorhandler configuration causes unmount to hang, and hence the filesystemmust be configured appropriately before unmount begins to preventunmount hangs.

Each filesystem has specific error class handlers that define the errorpropagation behaviour for specific errors. There is also a “default” errorhandler defined, which defines the behaviour for all errors that don’t havespecific handlers defined. Where multiple retry constraints are configured fora single error, the first retry configuration that expires will cause the errorto be propagated. The handler configurations are found in the directory:

/sys/fs/xfs/<dev>/error/<class>/<error>/

max_retries (Min: -1 Default: Varies Max: INTMAX)

Defines the allowed number of retries of a specific error beforethe filesystem will propagate the error. The retry count for a givenerror context (e.g. a specific metadata buffer) is reset every timethere is a successful completion of the operation.

Setting the value to “-1” will cause XFS to retry forever for thisspecific error.

Setting the value to “0” will cause XFS to fail immediately when thespecific error is reported.

Setting the value to “N” (where 0 < N < Max) will make XFS retry theoperation “N” times before propagating the error.

retry_timeout_seconds (Min: -1 Default: Varies Max: 1 day)

Define the amount of time (in seconds) that the filesystem isallowed to retry its operations when the specific error isfound.

Setting the value to “-1” will allow XFS to retry forever for thisspecific error.

Setting the value to “0” will cause XFS to fail immediately when thespecific error is reported.

Setting the value to “N” (where 0 < N < Max) will allow XFS to retry theoperation for up to “N” seconds before propagating the error.

Note: The default behaviour for a specific error handler is dependent on boththe class and error context. For example, the default values for“metadata/ENODEV” are “0” rather than “-1” so that this error handler defaultsto “fail immediately” behaviour. This is done because ENODEV is a fatal,unrecoverable error no matter how many times the metadata IO is retried.