Note

This document describes the rpmsg bus and how to write rpmsg drivers.To learn how to add rpmsg support for new platforms, check out remoteproc.txt(also a resident of Documentation/).

Introduction¶

Modern SoCs typically employ heterogeneous remote processor devices inasymmetric multiprocessing (AMP) configurations, which may be runningdifferent instances of operating system, whether it’s Linux or any otherflavor of real-time OS.

OMAP4, for example, has dual Cortex-A9, dual Cortex-M3 and a C64x+ DSP.Typically, the dual cortex-A9 is running Linux in a SMP configuration,and each of the other three cores (two M3 cores and a DSP) is runningits own instance of RTOS in an AMP configuration.

Typically AMP remote processors employ dedicated DSP codecs and multimediahardware accelerators, and therefore are often used to offload CPU-intensivemultimedia tasks from the main application processor.

These remote processors could also be used to control latency-sensitivesensors, drive random hardware blocks, or just perform background taskswhile the main CPU is idling.

Users of those remote processors can either be userland apps (e.g. multimediaframeworks talking with remote OMX components) or kernel drivers (controllinghardware accessible only by the remote processor, reserving kernel-controlledresources on behalf of the remote processor, etc..).

Rpmsg is a virtio-based messaging bus that allows kernel drivers to communicatewith remote processors available on the system. In turn, drivers could thenexpose appropriate user space interfaces, if needed.

When writing a driver that exposes rpmsg communication to userland, pleasekeep in mind that remote processors might have direct access to thesystem’s physical memory and other sensitive hardware resources (e.g. onOMAP4, remote cores and hardware accelerators may have direct access to thephysical memory, gpio banks, dma controllers, i2c bus, gptimers, mailboxdevices, hwspinlocks, etc..). Moreover, those remote processors might berunning RTOS where every task can access the entire memory/devices exposedto the processor. To minimize the risks of rogue (or buggy) userland codeexploiting remote bugs, and by that taking over the system, it is oftendesired to limit userland to specific rpmsg channels (see definition below)it can send messages on, and if possible, minimize how much controlit has over the content of the messages.

Every rpmsg device is a communication channel with a remote processor (thusrpmsg devices are called channels). Channels are identified by a textual nameand have a local (“source”) rpmsg address, and remote (“destination”) rpmsgaddress.

When a driver starts listening on a channel, its rx callback is bound witha unique rpmsg local address (a 32-bit integer). This way when inbound messagesarrive, the rpmsg core dispatches them to the appropriate driver accordingto their destination address (this is done by invoking the driver’s rx handlerwith the payload of the inbound message).

User API¶

int rpmsg_send(struct rpmsg_channel *rpdev, void *data, int len);

sends a message across to the remote processor on a given channel.The caller should specify the channel, the data it wants to send,and its length (in bytes). The message will be sent on the specifiedchannel, i.e. its source and destination address fields will beset to the channel’s src and dst addresses.

In case there are no TX buffers available, the function will block untilone becomes available (i.e. until the remote processor consumesa tx buffer and puts it back on virtio’s used descriptor ring),or a timeout of 15 seconds elapses. When the latter happens,-ERESTARTSYS is returned.

The function can only be called from a process context (for now).Returns 0 on success and an appropriate error value on failure.

int rpmsg_sendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst);

sends a message across to the remote processor on a given channel,to a destination address provided by the caller.

The caller should specify the channel, the data it wants to send,its length (in bytes), and an explicit destination address.

The message will then be sent to the remote processor to which thechannel belongs, using the channel’s src address, and the user-provideddst address (thus the channel’s dst address will be ignored).

In case there are no TX buffers available, the function will block untilone becomes available (i.e. until the remote processor consumesa tx buffer and puts it back on virtio’s used descriptor ring),or a timeout of 15 seconds elapses. When the latter happens,-ERESTARTSYS is returned.

The function can only be called from a process context (for now).Returns 0 on success and an appropriate error value on failure.

int rpmsg_send_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst,                                                      void *data, int len);

sends a message across to the remote processor, using the src and dstaddresses provided by the user.

The caller should specify the channel, the data it wants to send,its length (in bytes), and explicit source and destination addresses.The message will then be sent to the remote processor to which thechannel belongs, but the channel’s src and dst addresses will beignored (and the user-provided addresses will be used instead).

In case there are no TX buffers available, the function will block untilone becomes available (i.e. until the remote processor consumesa tx buffer and puts it back on virtio’s used descriptor ring),or a timeout of 15 seconds elapses. When the latter happens,-ERESTARTSYS is returned.

The function can only be called from a process context (for now).Returns 0 on success and an appropriate error value on failure.

int rpmsg_trysend(struct rpmsg_channel *rpdev, void *data, int len);

sends a message across to the remote processor on a given channel.The caller should specify the channel, the data it wants to send,and its length (in bytes). The message will be sent on the specifiedchannel, i.e. its source and destination address fields will beset to the channel’s src and dst addresses.

In case there are no TX buffers available, the function will immediatelyreturn -ENOMEM without waiting until one becomes available.

The function can only be called from a process context (for now).Returns 0 on success and an appropriate error value on failure.

int rpmsg_trysendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst)

sends a message across to the remote processor on a given channel,to a destination address provided by the user.

The user should specify the channel, the data it wants to send,its length (in bytes), and an explicit destination address.

The message will then be sent to the remote processor to which thechannel belongs, using the channel’s src address, and the user-provideddst address (thus the channel’s dst address will be ignored).

In case there are no TX buffers available, the function will immediatelyreturn -ENOMEM without waiting until one becomes available.

The function can only be called from a process context (for now).Returns 0 on success and an appropriate error value on failure.

int rpmsg_trysend_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst,                                                      void *data, int len);

sends a message across to the remote processor, using source anddestination addresses provided by the user.

The user should specify the channel, the data it wants to send,its length (in bytes), and explicit source and destination addresses.The message will then be sent to the remote processor to which thechannel belongs, but the channel’s src and dst addresses will beignored (and the user-provided addresses will be used instead).

In case there are no TX buffers available, the function will immediatelyreturn -ENOMEM without waiting until one becomes available.

The function can only be called from a process context (for now).Returns 0 on success and an appropriate error value on failure.

struct rpmsg_endpoint *rpmsg_create_ept(struct rpmsg_device *rpdev,                                        rpmsg_rx_cb_t cb, void *priv,                                        struct rpmsg_channel_info chinfo);

every rpmsg address in the system is bound to an rx callback (so wheninbound messages arrive, they are dispatched by the rpmsg bus using theappropriate callback handler) by means of an rpmsg_endpoint struct.

This function allows drivers to create such an endpoint, and by that,bind a callback, and possibly some private data too, to an rpmsg address(either one that is known in advance, or one that will be dynamicallyassigned for them).

Simple rpmsg drivers need not call rpmsg_create_ept, because an endpointis already created for them when they are probed by the rpmsg bus(using the rx callback they provide when they registered to the rpmsg bus).

So things should just work for simple drivers: they already have anendpoint, their rx callback is bound to their rpmsg address, and whenrelevant inbound messages arrive (i.e. messages which their dst addressequals to the src address of their rpmsg channel), the driver’s handleris invoked to process it.

That said, more complicated drivers might do need to allocateadditional rpmsg addresses, and bind them to different rx callbacks.To accomplish that, those drivers need to call this function.Drivers should provide their channel (so the new endpoint would bindto the same remote processor their channel belongs to), an rx callbackfunction, an optional private data (which is provided back when therx callback is invoked), and an address they want to bind with thecallback. If addr is RPMSG_ADDR_ANY, then rpmsg_create_ept willdynamically assign them an available rpmsg address (drivers should havea very good reason why not to always use RPMSG_ADDR_ANY here).

Returns a pointer to the endpoint on success, or NULL on error.

void rpmsg_destroy_ept(struct rpmsg_endpoint *ept);

destroys an existing rpmsg endpoint. user should provide a pointerto an rpmsg endpoint that was previously created with rpmsg_create_ept().

int register_rpmsg_driver(struct rpmsg_driver *rpdrv);

registers an rpmsg driver with the rpmsg bus. user should providea pointer to an rpmsg_driver struct, which contains the driver’s->probe() and ->remove() functions, an rx callback, and an id_tablespecifying the names of the channels this driver is interested tobe probed with.

void unregister_rpmsg_driver(struct rpmsg_driver *rpdrv);

unregisters an rpmsg driver from the rpmsg bus. user should providea pointer to a previously-registered rpmsg_driver struct.Returns 0 on success, and an appropriate error value on failure.

Typical usage¶

The following is a simple rpmsg driver, that sends an “hello!” messageon probe(), and whenever it receives an incoming message, it dumps itscontent to the console.

#include <linux/kernel.h>#include <linux/module.h>#include <linux/rpmsg.h>static void rpmsg_sample_cb(struct rpmsg_channel *rpdev, void *data, int len,                                              void *priv, u32 src){      print_hex_dump(KERN_INFO, "incoming message:", DUMP_PREFIX_NONE,                                              16, 1, data, len, true);}static int rpmsg_sample_probe(struct rpmsg_channel *rpdev){      int err;      dev_info(&rpdev->dev, "chnl: 0x%x -> 0x%x\n", rpdev->src, rpdev->dst);      /* send a message on our channel */      err = rpmsg_send(rpdev, "hello!", 6);      if (err) {              pr_err("rpmsg_send failed: %d\n", err);              return err;      }      return 0;}static void rpmsg_sample_remove(struct rpmsg_channel *rpdev){      dev_info(&rpdev->dev, "rpmsg sample client driver is removed\n");}static struct rpmsg_device_id rpmsg_driver_sample_id_table[] = {      { .name = "rpmsg-client-sample" },      { },};MODULE_DEVICE_TABLE(rpmsg, rpmsg_driver_sample_id_table);static struct rpmsg_driver rpmsg_sample_client = {      .drv.name       = KBUILD_MODNAME,      .id_table       = rpmsg_driver_sample_id_table,      .probe          = rpmsg_sample_probe,      .callback       = rpmsg_sample_cb,      .remove         = rpmsg_sample_remove,};module_rpmsg_driver(rpmsg_sample_client);

Allocations of rpmsg channels¶

At this point we only support dynamic allocations of rpmsg channels.

This is possible only with remote processors that have the VIRTIO_RPMSG_F_NSvirtio device feature set. This feature bit means that the remoteprocessor supports dynamic name service announcement messages.

When this feature is enabled, creation of rpmsg devices (i.e. channels)is completely dynamic: the remote processor announces the existence of aremote rpmsg service by sending a name service message (which containsthe name and rpmsg addr of the remote service, see struct rpmsg_ns_msg).

This message is then handled by the rpmsg bus, which in turn dynamicallycreates and registers an rpmsg channel (which represents the remote service).If/when a relevant rpmsg driver is registered, it will be immediately probedby the bus, and can then start sending messages to the remote service.

The plan is also to add static creation of rpmsg channels via the virtioconfig space, but it’s not implemented yet.