Hello - I'm venturing into a PC104 project and have few questions tostart off. I have no experience with PC104 whatsoever.The goal is for a...
Hello - I'm venturing into a PC104 project and have few questions tostart off. I have no experience with PC104 whatsoever.The goal is for a PC104 module to talk to another board with an FPGA onit. Questions are:1. Can I use any version of Linux on the PC104 ?2. To save time, I hope to use the PC104 in 8-bit mode. Does anyone seea problem with this approach ?3. Does anyone hav...
F.Y.IExcuse me for my little knowledge in pc104.What is the easiest way to communicate between a pc104 and a ordinarypc, is it possible...
F.Y.IExcuse me for my little knowledge in pc104.What is the easiest way to communicate between a pc104 and a ordinarypc, is it possible by pci slot ?In order to do that do I need the pc104+ ?thanks
I am having problems installing a new M-systems disk on chip 200 (64Mb) othe PC104). My PC104 is to run linux and i basically need to load an...
I am having problems installing a new M-systems disk on chip 200 (64Mb) othe PC104). My PC104 is to run linux and i basically need to load an imagonto the new disk on chip. I have a hard-drive connected to the pc104(usinthe old PPM-TX processor board) since the image is loaded on the harddriveSo when i try to get the pc104 to boot of the hardrive, it simply refuseto do so. is turning out...
Hi,I am a PC104 newbie.I am trying to boot a PC104 using a Compactflash flash memory card. To doso, I first copied system files onto it...
Hi,I am a PC104 newbie.I am trying to boot a PC104 using a Compactflash flash memory card. To doso, I first copied system files onto it (from a Windows98 machine). I thenused the flash card to boot the PC104, but encountered "Disk I/O error".Could someone let me know what could be wrong?Thanks,Niranjan
I have a project that I will be doing on a PC104 system.Before I call the dozens of vendors who don't give pricinginfo online, I would...
I have a project that I will be doing on a PC104 system.Before I call the dozens of vendors who don't give pricinginfo online, I would like to ask whether anyone else hasselected PC104 systems lately, and if so what they found.REQUIREMENTS:Very low performance 386 or 486. A 16Mhz 386SX would be overkill.Runs MS-DOS. 1MB memory.Very, very cheap. The cheaper the better...
I have a PC104 with Lan, what I would like to do is connect it up with adesktop computer and comunicate between the PC and the PC104 through...
I have a PC104 with Lan, what I would like to do is connect it up with adesktop computer and comunicate between the PC and the PC104 through lan,using dos and windows 98.What programs are out there where I can have Dos talking to windows 98.I just want control over the PC104 from the desktop, networking between dosand windows 98.I want to only use dos on the pc104 because it has...
Hi all,I use a CPLD to generate interrupt in a PC104 system. It work's fine.The question is:is correct connect CPLD output diretly to...
Hi all,I use a CPLD to generate interrupt in a PC104 system. It work's fine.The question is:is correct connect CPLD output diretly to PC104 IRQ input (i don't needinterrupt sharing)? Or i need other hardware (pull-up resistor or other) ?Thank's in advanceMax
I have searched a lot for a computer or at least a box with a backplane, where I can put in 5 or more PC104 cards.All PC104 computers I saw,...
I have searched a lot for a computer or at least a box with a backplane, where I can put in 5 or more PC104 cards.All PC104 computers I saw, only had cages with room for 2-3 cards.I think there must be providers offering larger cages.Is there someone who provides large cages with a back plane for I PC104processor card?thanks ulli
Hi folks,I am about to emabark on a new development using a COTS PC104 singleboard computer (probably Arcom Viper) for use in an industrial...
Hi folks,I am about to emabark on a new development using a COTS PC104 singleboard computer (probably Arcom Viper) for use in an industrial controlsystem. The PC104 will perform the role of an autonomous serial dataacquisition hub with some basic control functions. The PC104 will beinstalled in a remote location with proprietary ethernet or serialprotocols revovering data from the PC...
Hey guys, first time posting here. I'm new to PC104. At uni we are buildinga mini electric race car and the team decided to use a PC104 to...
Hey guys, first time posting here. I'm new to PC104. At uni we are buildinga mini electric race car and the team decided to use a PC104 to runeverything including data acquisition (don't know why they opted for aground up system when there were packages available for noobs)We are using two brush less DC motors integrated with 2 inverters (DC to 3phase AC) and IGBT switch. The controller is...
is there any one who manufacture pc104 with pentium 4 and firewire , Pci slot.if so can you refer me to his web page? or correct me if i am...
is there any one who manufacture pc104 with pentium 4 and firewire , Pci slot.if so can you refer me to his web page? or correct me if i am wrong.thanks alotanahmany
HiJust recently purchased A PC104 board with ethernet lan,Is there any software around or aplications where I can load the softwareonto a...
HiJust recently purchased A PC104 board with ethernet lan,Is there any software around or aplications where I can load the softwareonto a 16mb disk on chip, I know that Iam using limited memory, but I haveread and seen at exibitions where they have pc104 boards connected to adesktop with windows 98 running and able to read or communicate with thepc104 board using a lan connection....
Hi all,Any recommendations for a PC104 plus SBC with good processing speedand withstand high temperature? I am worried about the PCI...
Hi all,Any recommendations for a PC104 plus SBC with good processing speedand withstand high temperature? I am worried about the PCI connectors.In some of the boards the OCI connectors become loose and the daughterboards come out some days.Thanks in advance.Krishna.
My idea is the following, is it completely absurd ?I know that W2000 server works with RAS on a pc104.Will W2003 server also work ?I'm...
My idea is the following, is it completely absurd ?I know that W2000 server works with RAS on a pc104.Will W2003 server also work ?I'm thinking about Win 2003 because i need the RAS (Remote Access Server forTCP/IP)- PC104 (CPU 400 Mhz + 128 MB ram)- HD 30 GB- GPRS radio modem through RS 232 (hopefully supported by the RAS)- Windows 2003 Standard Edition (becouse i need th...
I'm also trying to design a PC104 (ISA) bus board.I will interface an ADC (AD9220 or faster) via FIFO buffer to PC104 (ISA)bus.I need to...
I'm also trying to design a PC104 (ISA) bus board.I will interface an ADC (AD9220 or faster) via FIFO buffer to PC104 (ISA)bus.I need to control ADC to digitize input signal in a burst and store theconverted data into a FIFO.When FIFO is full, I need to generate an interrupt to signal the PC104 fordata transfer.Unfortunatelly I do not have enough experience with CPLD / FPGA (yet)....
I want 128bytes (small enough!) of NVRAM ina PC104 format. Google has not done it so far!Thanks for any leads. - RM
I want 128bytes (small enough!) of NVRAM ina PC104 format. Google has not done it so far!Thanks for any leads. - RM
What embedded software is out there to run on a PC104 for just datacollecting through the serial port.For example, data from a electronic...
What embedded software is out there to run on a PC104 for just datacollecting through the serial port.For example, data from a electronic balance, with a RS 232 interface.The PC104 has a 200mhz CPU 16mb of ram, 500 cf card as hard drive.Thanks Chris
I recently purchased a PC104, what operating systems can be purchased to runthese boards.I have a Compact Flash Card aa a hard drive using...
I recently purchased a PC104, what operating systems can be purchased to runthese boards.I have a Compact Flash Card aa a hard drive using windows 95 and 98 whichwrites continusly to the compact flash.I would imagine this would shorten the life of the card.Would I be best using "CE" or Linix, C++, Dos etc.Thanks Simon
Hello,I have a small PC104 device with one USB port. As of yet, I'm not too familiar with USB, except to know there is exactly 1 master and...
Hello,I have a small PC104 device with one USB port. As of yet, I'm not too familiar with USB, except to know there is exactly 1 master and many slaves.I would like to know if it is possible to make the PC104 device look like a slave, so that I can have it emulate a "usb storage device".It's used for a logger, and eventually I'll insert a harddrive (instead of the now current fla...
Hi,I have a PC104 from kontron (mops_lcd) thatI can't read IO ports from the ISA bus,The write to ports is ok but the read gets0xff...
Hi,I have a PC104 from kontron (mops_lcd) thatI can't read IO ports from the ISA bus,The write to ports is ok but the read gets0xff always. (even with datalines forced '0' all the time)Looks that IO input is comming from elsewhereas onboard devices like LPT or COM work wellI suspect a bridge config or whatever...Kontron support doesn't really help and Iwonder if anyone has step...
