Hi, everybody!I am trying to build a parallel port ICP adapter. I think it will be quite usefull and low cost.But I can not read data from...
Hi, everybody!I am trying to build a parallel port ICP adapter. I think it will be quite usefull and low cost.But I can not read data from the device(LPC9107), the data line is always high when read. What may be the problem?To get in programming mode the RESET pin has to have a sequence of 7 pulses after the rising edge of VDD and the RST high time must between 1-32us, which is e...
Hello..I Try to setup CCU PWM unit in LPC936 but cant get it working.Timer 0/1 as pwm works great but I need more PWM'sThe unit is...
Hello..I Try to setup CCU PWM unit in LPC936 but cant get it working.Timer 0/1 as pwm works great but I need more PWM'sThe unit is clocked with 18MHz external crystal. So I intend to use CCLK (18MHz) as CCU clk as PLL can't be set correctly with crystal over16MHz. Or I'm wrong?Pin P2.1 is set as Pushpol output and folowed code should 50%/50% cycle but it's on LOW all thetime...
Anyone done ISP on a 936?On the app. note AN10258, there is a statement that says 'To controlVDD, a PNP transistor is needed, because P2.3...
Anyone done ISP on a 936?On the app. note AN10258, there is a statement that says 'To controlVDD, a PNP transistor is needed, because P2.3 cannot supply enoughcurrent for the LPC9xx during programming.'Can I just supply 3.3V all the time to the 936 and not connect P2.3 tomy board? Problems with that?Sutton ------------------------------------
Hi,I'm sort of new at the LPC micros, but have some code apparentlycompiled with the Keil compiler for a lPC938. I've got...
Hi,I'm sort of new at the LPC micros, but have some code apparentlycompiled with the Keil compiler for a lPC938. I've got everythingcompiling fine, except for the ADC code. The relevant portions of thecode are this:(line 80): res = (XBYTE[AD0DAT0L_ADDR]<
Hello,I'm a new LPC935 user and for my first application, my microcontrollerBUG, where is the problem???(Sorry for my bad English, I've some...
Hello,I'm a new LPC935 user and for my first application, my microcontrollerBUG, where is the problem???(Sorry for my bad English, I've some difficulties with this language)Explanation:First, I'm developing my program direct in assembler with =B5vision3.=20It's a easy program to verify if my =B5C do it correctly but I've nooutput :(The program :org0000hljmpstart=09or...
Hi,I have a problem with programming P89LPC922.I use ISP, i can programm it 1 time then i cannot programm it again. If i change the...
Hi,I have a problem with programming P89LPC922.I use ISP, i can programm it 1 time then i cannot programm it again. If i change the processor, i can programm it 1 time then it's all. The processor doesn't respond on TX.Do you have an idea of what appends?Thanks a lotDavid
Hi all!I need to know the MFGID, ID1 and ID2 for the new LPC954 device.I suppose that MFGID = 15H and ID1 = DDH, but ID2?Is there an...
Hi all!I need to know the MFGID, ID1 and ID2 for the new LPC954 device.I suppose that MFGID = 15H and ID1 = DDH, but ID2?Is there an updated ICP_LPC9xx_v27.pdf (P89LPC900 In-Circuit Programming Specifications) available?On the user manual I read that the P89LPC952/954 program memory consists 1 kB sectors. This is true for LPC952 (8K total flash), but the only other LPC900 devi...
Hi,I'm using a P89LPC936 with a 12MHz crystal (SMD case HC49/4H)The uC doesn't always start.It seems that oscillation level is too small...
Hi,I'm using a P89LPC936 with a 12MHz crystal (SMD case HC49/4H)The uC doesn't always start.It seems that oscillation level is too small (0.5V to 1.6V with 3.3V Vdd).Also it seems to work fine with a classic crystal (not SMD).The reason could be that classic crystal have serie resistance (about 10 ohms) much lower then SMD crystal (about 30 ohms). And the 89LPC936 doesn't have enou...
I just found an error in the P89LPC952 User Manual (Rev.00), and also in the reg952.h header file that you can download from the Keil...
I just found an error in the P89LPC952 User Manual (Rev.00), and also in the reg952.h header file that you can download from the Keil website.The error is in the serial port 1 control register: S1CON correct address is B6H, while at pages 55 and 58 it's indicated as B5H.Fortunately you can find it correctly indicated as B6H at page 15.As I said, the error is also in the keil C51 re...
It seems that the bondout chip on the EPM900 is a 89LPC932.The LPC932 don't have analog fonctions and is code limited.Is there a boundout...
It seems that the bondout chip on the EPM900 is a 89LPC932.The LPC932 don't have analog fonctions and is code limited.Is there a boundout chip for the P89LPC936 ?And where can we find it (distributors ?)Thanks------------------------ Yahoo! Groups Sponsor --------------------~--> =20Home is just a click away.=A0 Make Yahoo! your home page now.http://us.click.yahoo.com/DHchtC/3FxN
Tosignificantly increase your chances of receiving answers, please make sure to:
