Available from:
Aliexpress.com
Amazon.de
Aliexpress.com
Banggood.com
Manufacturer:
Alibaba.com
Install method:
Tasmota pre-installed
| GPIO # | Component |
|---|---|
| GPIO00 | None |
| GPIO01 | None |
| GPIO02 | Zigbee Tx |
| GPIO03 | None |
| GPIO04 | Zigbee Rx |
| GPIO05 | None |
| GPIO09 | None |
| GPIO10 | None |
| GPIO12 | Zigbee RST 2 |
| GPIO13 | Zigbee RST 1 |
| GPIO14 | Led_i 1 |
| GPIO15 | LedLink |
| GPIO16 | ETH POWER |
| GPIO17 | None |
| GPIO18 | ETH MDIO |
| GPIO19 | None |
| GPIO20 | None |
| GPIO21 | None |
| GPIO22 | None |
| GPIO23 | ETH MDC |
| GPIO24 | None |
| GPIO25 | None |
| GPIO26 | None |
| GPIO27 | None |
| GPIO6 | None |
| GPIO7 | None |
| GPIO8 | None |
| GPIO11 | None |
| GPIO32 | I2C SCL 1 |
| GPIO33 | I2C SDA 1 |
| GPIO34 | Button 1 |
| GPIO35 | None |
| GPIO36 | None |
| GPIO37 | None |
| GPIO38 | None |
| GPIO39 | None |
{"NAME":"ZB-GW03-V1.2","GPIO":[0,0,3552,0,3584,0,0,0,5793,5792,320,544,5536,0,5600,0,0,0,0,5568,0,0,0,0,0,0,0,0,608,640,32,0,0,0,0,0],"FLAG":0,"BASE":1}Preflashed version is not available from all vendors!
Serial Flash
Downloadtasmota32-zigbeebridge.factory.bin unofficial precompiled firmware from development branch and flash the ESP32 module. Or usetasmota32-zigbeebridge.bin for OTA upgrade.
Flash Zigbee module
Download Zigbee module firmware (for example:ncp-uart-sw_6.7.8_115200.ota) from Tasmota GitHub located inTasmota/tools/fw_SonoffZigbeeBridge_ezsp/.
Go toFirmware Upgrade and next to “Upgrade by file upload” use theChoose File button and select Zigbee module firmware you downloaded f.e. (ncp-uart-sw_6.7.8_115200.ota).
Click onStart upgrade, be patient and wait for a few minutes until flashing is complete. Once it is done, Tasmota will reboot. If the flash was successful the console will show Zigbee2Tasmota starting:
16:31:11 ZIG: Resetting EZSP device16:31:12 RSL: tele/zbbridge/RESULT = {"ZbState":{"Status":1,"Message":"EFR32 booted","RestartReason":"Power-on","Code":2}}16:31:12 RSL: tele/zbbridge/RESULT = {"ZbState":{"Status":55,"Version":"6.7.8.0","Protocol":8,"Stack":2}}16:31:12 RSL: tele/zbbridge/RESULT = {"ZbState":{"Status":3,"Message":"Configured, starting coordinator"}}16:31:13 RSL: tele/zbbridge/RESULT = {"ZbState":{"Status":56,"IEEEAddr":"0x80E423FFFE225691","ShortAddr":"0x0000","DeviceType":1}}16:31:14 ZIG: Subscribe to group 0 'ZbListen0 0'16:31:14 RSL: tele/zbbridge/RESULT = {"ZbState":{"Status":0,"Message":"Started"}}16:31:14 ZIG: Zigbee started16:31:14 ZIG: No zigbee devices data in FlashFirmware build
To build your own firmware for Tasmota32 that includes ethernet and zigbee support:
user_config_override.h:
#ifdef FIRMWARE_EWELINK #warning **** Build: FIRMWARE FOR EWELINK ZB-GW03-V1.2 **** #undef SERIAL_LOG_LEVEL #define SERIAL_LOG_LEVEL LOG_LEVEL_NONE #define USE_ZIGBEE #undef USE_ZIGBEE_ZNP #define USE_ZIGBEE_EZSP #define USE_UFILESYS #define USE_ZIGBEE_EEPROM // T24C512A #define USE_TCP_BRIDGE #undef USE_ZIGBEE_CHANNEL #define USE_ZIGBEE_CHANNEL 11 // (11-26) #define USE_ETHERNET #undef ETH_TYPE #define ETH_TYPE 0 // ETH_PHY_LAN8720 #undef ETH_CLKMODE #define ETH_CLKMODE 3 // ETH_CLOCK_GPIO17_OUT #undef ETH_ADDRESS #define ETH_ADDRESS 1 // PHY1#endifplatformio_override.ini
[env:tasmota32-EWELINK]extends = env:tasmota32board_build.f_cpu = 240000000Lboard_build.f_flash = 40000000Lbuild_flags = ${env:tasmota32_base.build_flags} -DFIRMWARE_EWELINKDetailed Instructions
Step-by-step instructions to build custom firmware, flash the device, and final setup steps to work with or without Home Assistant:https://thehelpfulidiot.com/a-wired-sonoff-zigbee-alternative
[8]ページ先頭