Movatterモバイル変換

[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]

PROPOSED STANDARD

Internet Engineering Task Force (IETF) A. ClarkRequest for Comments: 7005 TelchemyCategory: Standards Track V. SinghISSN: 2070-1721 Aalto University Q. Wu Huawei September 2013RTP Control Protocol (RTCP) Extended Report (XR) Blockfor De-Jitter Buffer Metric ReportingAbstract This document defines an RTP Control Protocol (RTCP) Extended Report (XR) block that allows the reporting of de-jitter buffer metrics for a range of RTP applications.Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available inSection 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained athttp://www.rfc-editor.org/info/rfc7005.Copyright Notice Copyright (c) 2013 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject toBCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.Clark, et al. Standards Track [Page 1]

RFC 7005                  RTCP XR Jitter Buffer           September 2013Table of Contents1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .31.1.  De-Jitter Buffer Metrics Block . . . . . . . . . . . . . .31.2.  RTCP and RTCP Extended Reports . . . . . . . . . . . . . .31.3.  Performance Metrics Framework  . . . . . . . . . . . . . .31.4.  Applicability  . . . . . . . . . . . . . . . . . . . . . .32.  Standards Language . . . . . . . . . . . . . . . . . . . . . .43.  De-Jitter Buffer Operation . . . . . . . . . . . . . . . . . .43.1.  Idealized De-Jitter Buffer . . . . . . . . . . . . . . . .43.2.  Fixed De-Jitter Buffer . . . . . . . . . . . . . . . . . .53.3.  Adaptive De-Jitter Buffer  . . . . . . . . . . . . . . . .54.  De-Jitter Buffer Metrics Block . . . . . . . . . . . . . . . .64.1.  Report Block Structure . . . . . . . . . . . . . . . . . .64.2.  Definition of Fields in De-Jitter Buffer Metrics Block . .65.  SDP Signaling  . . . . . . . . . . . . . . . . . . . . . . . .95.1.  SDP rtcp-xr-attrib Attribute Extension . . . . . . . . . .95.2.  Offer/Answer Usage . . . . . . . . . . . . . . . . . . . .96.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . .96.1.  New RTCP XR Block Type Value . . . . . . . . . . . . . . .96.2.  New RTCP XR SDP Parameter  . . . . . . . . . . . . . . . .106.3.  Contact Information for Registrations  . . . . . . . . . .107.  Security Considerations  . . . . . . . . . . . . . . . . . . .108.  Contributors . . . . . . . . . . . . . . . . . . . . . . . . .109.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . .1010. References . . . . . . . . . . . . . . . . . . . . . . . . . .1010.1. Normative References . . . . . . . . . . . . . . . . . . .1010.2. Informative References . . . . . . . . . . . . . . . . . .11Appendix A.  Metrics Represented Using the Template fromRFC 6390  . . . . . . . . . . . . . . . . . . . . . .12Clark, et al.                Standards Track                    [Page 2]

RFC 7005                  RTCP XR Jitter Buffer           September 20131.  Introduction1.1.  De-Jitter Buffer Metrics Block   This document defines a new block type to augment those defined in   [RFC3611] for use in a range of RTP applications.   The new block type provides information on de-jitter buffer   configuration and performance.   The metric belongs to the class of transport-related end-system   metrics defined in [RFC6792].   Instances of this metrics block refer by synchronization source   (SSRC) to the separate auxiliary Measurement Information Block   [RFC6776], which contains information such as the SSRC of the   measured stream, and RTP sequence numbers and time intervals   indicating the span of the report.1.2.  RTCP and RTCP Extended Reports   The use of RTCP for reporting is defined in [RFC3550].  [RFC3611]   defines an extensible structure for reporting using an RTCP Extended   Report (XR).  This document defines a new Extended Report block for   use with [RFC3550] and [RFC3611].1.3.  Performance Metrics Framework   "Guidelines for Considering New Performance Metric Development"   [RFC6390] provides guidance on the definition and specification of   performance metrics.  "Guidelines for Use of the RTP Monitoring   Framework" [RFC6792] provides guidance on the reporting block format   using RTCP XR.  Metrics described in this document are in accordance   with the guidelines in [RFC6390]and [RFC6792].1.4.  Applicability   Real-time applications employ a de-jitter buffer [RFC5481] to absorb   jitter introduced on the path from source to destination.  These   metrics are used to report how the de-jitter buffer at the receiving   end of the RTP stream behaves as a result of jitter in the network;   they are applicable to a range of RTP applications.   These metrics correspond to terminal-related factors that affect   real-time application quality and are useful for providing a better   end-user quality of experience (QoE) when these terminal-related   factors are used as inputs to calculate QoE metrics [QMB].Clark, et al.                Standards Track                    [Page 3]

RFC 7005 RTCP XR Jitter Buffer September 20132. Standards Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described inRFC 2119 [RFC2119].3. De-Jitter Buffer Operation A de-jitter buffer is required to absorb delay variation in the network delivery of media packets. A de-jitter buffer works by holding media data for a period of time after it is received and before it is played out. Packets that arrive early are held in the de-jitter buffer longer. If packets arrive too early, they may be discarded if there is no available de-jitter buffer space. If packets are delayed excessively by the network, they may be discarded if they miss their playout time. The de-jitter buffer can be considered a time window with the early edge aligned with the delay corresponding to the earliest arriving packet and the late edge representing the maximum permissible delay before a late arriving packet would be discarded. The delay applied to packets that arrive on time or at their expected arrival time is known as the nominal delay, and this is equivalent to the time difference/buffer size difference between the insertion point of the on-time packets and the point at which the packets are read out. The reference for the expected arrival time may be, for example, the first packet in the session or the running average delay. If all packets arrived at their expected arrival time, then every packet would be held in the de-jitter buffer exactly the nominal delay. The de-jitter buffer maximum delay is the delay that is applied to the earliest arriving packet that is not discarded and corresponds to the early edge of the de-jitter buffer time window.3.1. Idealized De-Jitter Buffer In practice, de-jitter buffer implementations vary considerably; however, they should behave in a manner conceptually consistent with an idealized de-jitter buffer, which is described as follows:Clark, et al. Standards Track [Page 4]

RFC 7005                  RTCP XR Jitter Buffer           September 2013   (i)    Receive the first packet and delay playout by D ms.  Keep the          RTP timestamp (TS) and receive time as a reference.          RTP TS[1]          receive time[1]          Assume that both are normalized in ticks (there are 10,000          ticks in a millisecond).   (ii)   Receive the next packet.   (iii)  Calculate r = RTP TS[n] - RTP TS[1] and t = receive time[n] -          receive time[1].  If r == t, then the packet arrived on time.          If r < t, then the packet arrived late, and if r > t, then the          packet arrived early.   (iv)   Delay playout of packet by D + (r-t).   (v)    Go back to (ii).   Note that this idealized implementation assumes that the sender's RTP   clock is synchronized to the clock in the receiver, which is used to   timestamp packet arrivals.  If there is no such inherent   synchronization, the system may need to use an adaptive de-jitter   buffer or other techniques to ensure reliable reception.3.2.  Fixed De-Jitter Buffer   A fixed de-jitter buffer lacks provision to track the condition of   the network and has a fixed size, and packets leaving the de-jitter   buffer have a constant delay.  For fixed de-jitter buffer   implementation, the nominal delay is set to a constant value   corresponding to the packets that arrive at their expected arrival   time, while the maximum delay is set to a constant value   corresponding to the fixed size of the de-jitter buffer.3.3.  Adaptive De-Jitter Buffer   An adaptive de-jitter buffer can adapt to the change in the network's   delay and has variable size or variable delay.  It allows the nominal   delay to be set to a low value initially to minimize user perceived   delay; however, it can automatically extend the late edge (and   possibly also retract the early edge) of a buffer window if a   significant proportion of the packets are arriving late (and hence   being discarded).Clark, et al.                Standards Track                    [Page 5]

RFC 7005                  RTCP XR Jitter Buffer           September 20134.  De-Jitter Buffer Metrics Block   This block describes the configuration and operating parameters of   the de-jitter buffer in the receiver of the RTP end system or RTP   mixer that sends the report.  Instances of this metrics block use the   SSRC to refer to the separate auxiliary Measurement Information Block   [RFC6776], which describes the measurement periods in use (see[RFC6776], Section 4.2).  This metrics block relies on the   measurement interval in the Measurement Information Block indicating   the span of the report and MUST be sent in the same compound RTCP   packet as the Measurement Information Block.  If the measurement   interval is not received in the same compound RTCP packet as this   metrics block, this metrics block MUST be discarded.4.1.  Report Block Structure   De-Jitter Buffer (DJB) Metrics Block       0                   1                   2                   3       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+      |     BT=23    | I |C|  resv    |       Block Length=3          |      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+      |                           SSRC of Source                      |      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+      |          DJB nominal          |        DJB maximum            |      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+      |     DJB high-water mark       |      DJB low-water mark       |      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                     Figure 1: Report Block Structure4.2.  Definition of Fields in De-Jitter Buffer Metrics Block   Block Type (BT): 8 bits      A De-Jitter Buffer Metrics Report Block is identified by the      constant 23.   Interval Metric flag (I): 2 bits      This field is used to indicate whether the de-jitter buffer      metrics are Sampled, Interval, or Cumulative metrics:         I=01: Sampled Value - the reported value is a sampled         instantaneous value.Clark, et al.                Standards Track                    [Page 6]

RFC 7005                  RTCP XR Jitter Buffer           September 2013         I=10: Interval Duration - the reported value applies to the         most recent measurement interval duration between successive         metrics reports.         I=11: Cumulative Duration - the reported value applies to the         accumulation period characteristic of cumulative measurements.      In this document, de-jitter buffer metrics can only be sampled and      cannot be measured over definite intervals.  Also, the value I=00      is reserved for future use.  Senders MUST NOT use the values I=00,      I=10, or I=11.  If a block is received with I=00, I=10, or I=11,      the receiver MUST discard the block.   Jitter Buffer Configuration (C): 1 bit      This field is used to identify the de-jitter buffer method in use      at the receiver, according to the following code:         0 = Fixed de-jitter buffer         1 = Adaptive de-jitter buffer   Reserved (resv): 5 bits      These bits are reserved.  They MUST be set to zero by senders and      ignored by receivers (see[RFC6709], Section 4.2).   Block Length: 16 bits      The length of this report block in 32-bit words, minus one, in      accordance with the definition in [RFC3611].  This field MUST be      set to 3 to match the fixed length of the report block.   SSRC of Source: 32 bits      As defined inSection 4.1 of [RFC3611].   De-jitter buffer nominal delay (DJB nominal): 16 bits      This is the current nominal de-jitter buffer delay (in      milliseconds) that corresponds to the nominal de-jitter buffer      delay for packets that arrive exactly on time.  It is calculated      based on the time spent in the de-jitter buffer for the packet      that arrives exactly on time.  This parameter MUST be provided for      both fixed and adaptive de-jitter buffer implementations.Clark, et al.                Standards Track                    [Page 7]

RFC 7005 RTCP XR Jitter Buffer September 2013 The measured value is an unsigned value. If the measured value exceeds 0xFFFD, the value 0xFFFE MUST be reported to indicate an over-range measurement. If the measurement is unavailable, the value 0xFFFF MUST be reported. De-jitter buffer maximum delay (DJB maximum): 16 bits This is the current maximum de-jitter buffer delay (in milliseconds) that corresponds to the earliest arriving packet that would not be discarded. It is calculated based on the time spent in the de-jitter buffer for the earliest arriving packet. In simple queue implementations, this may correspond to the size of the de-jitter buffer. In adaptive de-jitter buffer implementations, this value may vary dynamically. This parameter MUST be provided for both fixed and adaptive de-jitter buffer implementations. The measured value is an unsigned value. If the measured value exceeds 0xFFFD, the value 0xFFFE MUST be reported to indicate an over-range measurement. If the measurement is unavailable, the value 0xFFFF MUST be reported. De-jitter buffer high-water mark (DJB high-water mark): 16 bits This is the highest value of the de-jitter buffer nominal delay (in milliseconds) that occurred at any time during the reporting interval. This parameter MUST be provided for adaptive de-jitter buffer implementations, and its value MUST be set to DJB maximum for fixed de-jitter buffer implementations. The measured value is an unsigned value. If the measured value exceeds 0xFFFD, the value 0xFFFE MUST be reported to indicate an over-range measurement. If the measurement is unavailable, the value 0xFFFF MUST be reported. De-jitter buffer low-water mark (DJB low-water mark): 16 bits This is the lowest value of the de-jitter buffer nominal delay (in milliseconds) that occurred at any time during the reporting interval. This parameter MUST be provided for adaptive de-jitter buffer implementations, and its value MUST be set to DJB maximum for fixed de-jitter buffer implementations. The measured value is an unsigned value. If the measured value exceeds 0xFFFD, the value 0xFFFE MUST be reported to indicate an over-range measurement. If the measurement is unavailable, the value 0xFFFF MUST be reported.Clark, et al. Standards Track [Page 8]

RFC 7005                  RTCP XR Jitter Buffer           September 20135.  SDP Signaling   [RFC3611] defines the use of the Session Description Protocol (SDP)   [RFC4566] for signaling the use of XR blocks.  However, XR blocks MAY   be used without prior signaling (seeSection 5 of RFC 3611).5.1.  SDP rtcp-xr-attrib Attribute Extension   This section augments the SDP [RFC4566] attribute "rtcp-xr" defined   in [RFC3611] by providing an additional value of "xr-format" to   signal the use of the report block defined in this document.   xr-format =/ xr-djb-block   xr-djb-block = "de-jitter-buffer"5.2.  Offer/Answer Usage   When SDP is used in Offer/Answer context [RFC3264], the SDP Offer/   Answer usage defined in [RFC3611] for unilateral "rtcp-xr" attribute   parameters applies.  For detailed usage of Offer/Answer for   unilateral parameters, refer toSection 5.2 of [RFC3611].6.  IANA Considerations   New block types for RTCP XR are subject to IANA registration.  For   general guidelines on IANA considerations for RTCP XR, refer to   [RFC3611].6.1.  New RTCP XR Block Type Value   This document assigns the block type value 23 in the IANA "RTP   Control Protocol Extended Reports (RTCP XR) Block Type Registry" to   the "De-Jitter Buffer Metrics Block".6.2.  New RTCP XR SDP Parameter   This document also registers a new parameter "de-jitter-buffer" in   the "RTP Control Protocol Extended Reports (RTCP XR) Session   Description Protocol (SDP) Parameters Registry".Clark, et al.                Standards Track                    [Page 9]

RFC 7005 RTCP XR Jitter Buffer September 20136.3. Contact Information for Registrations The contact information for registrations is: Qin Wu (sunseawq@huawei.com) 101 Software Avenue, Yuhua District Nanjing, Jiangsu 210012 China7. Security Considerations It is believed that this RTCP XR block introduces no new security considerations beyond those described in [RFC3611]. This block does not provide per-packet statistics, so the risk to confidentiality documented inSection 7, paragraph 3 of [RFC3611] does not apply.8. Contributors Geoff Hunt wrote the initial draft of this document.9. Acknowledgments The authors gratefully acknowledge reviews and feedback provided by Bruce Adams, Philip Arden, Amit Arora, Claire Bi, Bob Biskner, Benoit Claise, Kevin Connor, Claus Dahm, Spencer Dawkins, Randy Ethier, Roni Even, Jim Frauenthal, Kevin Gross, Albert Higashi, Tom Hock, Shane Holthaus, Paul Jones, Rajesh Kumar, Keith Lantz, Mohamed Mostafa, Amy Pendleton, Colin Perkins, Mike Ramalho, Ravi Raviraj, Dan Romascanu, Albrecht Schwarz, Tom Taylor, Hideaki Yamada, and Glen Zorn.10. References10.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels",BCP 14,RFC 2119, March 1997. [RFC3264] Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model with Session Description Protocol (SDP)",RFC 3264, June 2002. [RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, "RTP: A Transport Protocol for Real-Time Applications", STD 64,RFC 3550, July 2003. [RFC3611] Friedman, T., Caceres, R., and A. Clark, "RTP Control Protocol Extended Reports (RTCP XR)",RFC 3611, November 2003.Clark, et al. Standards Track [Page 10]

RFC 7005                  RTCP XR Jitter Buffer           September 2013   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session              Description Protocol",RFC 4566, July 2006.   [RFC6776]  Clark, A. and Q. Wu, "Measurement Identity and Information              Reporting Using a Source Description (SDES) Item and an              RTCP Extended Report (XR) Block",RFC 6776, October 2012.10.2.  Informative References   [QMB]      Clark, A., "RTP Control Protocol (RTCP) Extended Report              (XR) Blocks for QoE Metric Reporting", Work in Progress,              May 2013.   [RFC5481]  Morton, A. and B. Claise, "Packet Delay Variation              Applicability Statement",RFC 5481, March 2009.   [RFC6390]  Clark, A. and B. Claise, "Guidelines for Considering New              Performance Metric Development",BCP 170,RFC 6390,              October 2011.   [RFC6709]  Carpenter, B., Aboba, B., and S. Cheshire, "Design              Considerations for Protocol Extensions",RFC 6709,              September 2012.   [RFC6792]  Wu, Q., Hunt, G., and P. Arden, "Guidelines for Use of the              RTP Monitoring Framework",RFC 6792, November 2012.Clark, et al.                Standards Track                   [Page 11]

RFC 7005 RTCP XR Jitter Buffer September 2013Appendix A. Metrics Represented Using the Template fromRFC 6390 a. De-Jitter Buffer Nominal Delay Metric * Metric Name: De-jitter buffer nominal delay in RTP * Metric Description: The "expected arrival time" is the time that an RTP packet would arrive if there was no delay variation. The delay applied to packets that arrive at their expected time is known as the Nominal Delay. * Method of Measurement or Calculation: SeeSection 4.2, de-jitter buffer nominal delay definition. * Units of Measurement: SeeSection 4.2, de-jitter buffer nominal delay definition. * Measurement Point(s) with Potential Measurement Domain: SeeSection 4. * Measurement Timing: SeeSection 4 for measurement timing andSection 4.2 for Interval Metric flag. * Use and Applications: SeeSection 1.4. * Reporting Model: SeeRFC 3611. b. De-Jitter Buffer Maximum Delay Metric * Metric Name: De-jitter buffer maximum delay in RTP. * Metric Description: It is the current maximum de-jitter buffer delay for RTP traffic that corresponds to the earliest arriving packet that would not be discarded. * Method of Measurement or Calculation: SeeSection 4.2, de-jitter buffer maximum delay definition andSection 3, the last paragraph. * Units of Measurement: SeeSection 4.2, de-jitter buffer maximum delay definition. * Measurement Point(s) with Potential Measurement Domain: SeeSection 4. * Measurement Timing: SeeSection 4 for measurement timing andSection 4.2 for Interval Metric flag.Clark, et al. Standards Track [Page 12]

RFC 7005 RTCP XR Jitter Buffer September 2013 * Use and Applications: SeeSection 1.4. * Reporting Model: SeeRFC 3611. c. De-Jitter Buffer High-Water Mark Metric * Metric Name: De-jitter buffer high-water mark in RTP. * Metric Description: It is the highest value of the de-jitter buffer nominal delay for RTP traffic which occurred at any time during the reporting interval. * Method of Measurement or Calculation: SeeSection 4.2, de-jitter buffer high-water mark definition. * Units of Measurement: SeeSection 4.2, de-jitter buffer nominal delay definition. * Measurement Point(s) with Potential Measurement Domain: SeeSection 4. * Measurement Timing: SeeSection 4 for measurement timing andSection 4.2 for Interval Metric flag. * Use and Applications: SeeSection 1.4. * Reporting Model: SeeRFC 3611. d. De-Jitter Buffer Low-Water Mark Metric * Metric Name: De-jitter buffer low-water mark in RTP. * Metric Description: It is the lowest value of the de-jitter buffer nominal delay (for RTP traffic) that occurred at any time during the reporting interval. * Method of Measurement or Calculation: SeeSection 4.2, de-jitter buffer low-water mark definition. * Units of Measurement: SeeSection 4.2, de-jitter buffer low water mark definition. * Measurement Point(s) with Potential Measurement Domain: SeeSection 4, 1st paragraph. * Measurement Timing: SeeSection 4 for measurement timing andSection 4.2 for Interval Metric flag.Clark, et al. Standards Track [Page 13]

RFC 7005                  RTCP XR Jitter Buffer           September 2013       *  Use and Applications: SeeSection 1.4.       *  Reporting Model: SeeRFC 3611.Authors' Addresses   Alan Clark   Telchemy Incorporated   2905 Premiere Parkway, Suite 280   Duluth, GA  30097   USA   EMail: alan.d.clark@telchemy.com   Varun Singh   Aalto University   School of Electrical Engineering   Otakaari 5 A   Espoo, FIN  02150   Finland   EMail: varun@comnet.tkk.fi   Qin Wu   Huawei   101 Software Avenue, Yuhua District   Nanjing, Jiangsu  210012   China   EMail: sunseawq@huawei.comClark, et al.                Standards Track                   [Page 14]

[8]ページ先頭