Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]
INFORMATIONAL
Network Working Group J. HouttuinRequest for Comments: 1506 RARE SecretariatRARE Technical Report: 6 August 1993A Tutorial on Gatewaying between X.400 and Internet MailStatus of this Memo This memo provides information for the Internet community. It does not specify an Internet standard. Distribution of this memo is unlimited.Introduction There are many ways in which X.400 and Internet (STD 11,RFC 822) mail systems can be interconnected. Addresses and service elements can be mapped onto each other in different ways. From the early available gateway implementations, one was not necessarily better than another, but the sole fact that each handled the mappings in a different way led to major interworking problems, especially when a message (or address) crossed more than one gateway. The need for one global standard on how to implement X.400 - Internet mail gatewaying was satisfied by the Internet Request For Comments 1327, titled "Mapping between X.400(1988)/ISO 10021 andRFC 822." This tutorial was produced especially to help new gateway managers find their way into the complicated subject of mail gatewaying according toRFC 1327. The need for such a tutorial can be illustrated by quoting the following discouraging paragraph fromRFC1327, chapter 1: "Warning: the remainder of this specification is technically detailed. It will not make sense, except in the context ofRFC 822 and X.400 (1988). Do not attempt to read this document unless you are familiar with these specifications." The introduction of this tutorial is general enough to be read not only by gateway managers, but also by e-mail managers who are new to gatewaying or to one of the two e-mail worlds in general. Parts of this introduction can be skipped as needed. For novice end-users, even this tutorial will be difficult to read. They are encouraged to use the COSINE MHS pocket user guide [14] instead. To a certain extent, this document can also be used as a reference guide to X.400 <->RFC 822 gatewaying. Wherever there is a lack of detail in the tutorial, it will at least point to the corresponding chapters in other documents. As such, it shields theRFC 1327 noviceRARE Working Group on Mail and Messaging (WG-MSG) [Page 1]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 from too much detail.Acknowledgements This tutorial is heavily based on other documents, such as [2], [6], [7], [8], and [11], from which large parts of text were reproduced (slightly edited) by kind permission from the authors. The author would like to thank the following persons for their thorough reviews: Peter Cowen (Nexor), Urs Eppenberger (SWITCH), Erik Huizer (SURFnet), Steve Kille (ISODE Consortium), Paul Klarenberg (NetConsult), Felix Kugler (SWITCH), Sabine Luethi.Disclaimer This document is not everywhere exact and/or complete in describing the involved standards. Irrelevant details are left out and some concepts are simplified for the ease of understanding. For reference purposes, always use the original documents.RARE Working Group on Mail and Messaging (WG-MSG) [Page 2]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993Table of Contents1. An overview of relevant standards ........................41.1. What is X.400 ? ......................................51.2. What is an RFC ? .....................................81.3. What isRFC 822 ? ....................................91.4. What isRFC 1327 ? ...................................112. Service Elements .........................................123. Address mapping ..........................................143.1. X.400 addresses ......................................153.1.1. Standard Attributes ..............................153.1.2. Domain Defined Attributes ........................173.1.3. X.400 address notation ...........................173.2.RFC 822 addresses ....................................193.3.RFC 1327 address mapping .............................203.3.1. Default mapping ..................................203.3.1.1. X.400 ->RFC 822 .............................203.3.1.2.RFC 822 -> X.400 .............................223.3.2. Exception mapping ................................233.3.2.1. PersonalName and localpart mapping ...........253.3.2.2. X.400 domain and domainpart mapping ..........263.3.2.2.1. X.400 ->RFC 822 .........................273.3.2.2.2.RFC 822 -> X.400 .........................283.4. Table co-ordination ..................................313.5. Local additions ......................................313.6. Product specific formats .............................323.7. Guidelines for mapping rule definition ...............344. Conclusion ...............................................35Appendix A. References ......................................36Appendix B. Index (Only available in the Postscript version) 37Appendix C. Abbreviations ...................................37Appendix D. How to access the MHS Co-ordination Server ......38 Security Considerations .....................................39 Author's Address ............................................39RARE Working Group on Mail and Messaging (WG-MSG) [Page 3]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 19931. An overview of relevant standards This chapter describes the history, status, future, and contents of the involved standards. There is a major difference between mail systems used in the USA and Europe. Mail systems originated mainly in the USA, where their explosive growth started as early as in the seventies. Different company-specific mail systems were developed simultaneously, which, of course, led to a high degree of incompatibility. The Advanced Research Projects Agency (ARPA), which had to use machines of many different manufacturers, triggered the development of the Internet and the TCP/IP protocol suite, which was later accepted as a standard by the US Department of Defense (DoD). The Internet mail format is defined in STD 11,RFC 822 and the protocol used for exchanging mail is known as the simple mail transfer protocol (SMTP) [1]. Together with UUCP and the BITNET protocol NJE, SMTP has become one of the main de facto mail standards in the US. Unfortunately, all these protocols were incompatible, which explains the need to come to an acceptable global mail standard. CCITT and ISO began working on a norm and their work converged in what is now known as the X.400 Series Recommendations. One of the objectives was to define a superset of the existing systems, allowing for easier integration later on. Some typical positive features of X.400 are the store-and-forward mechanism, the hierarchical address space and the possibility of combining different types of body parts into one message body. In Europe, the mail system boom came later. Since there was not much equipment in place yet, it made sense to use X.400 as much as possible right from the beginning. A strong X.400 lobby existed, especially in West-Germany (DFN). In the R&D world, mostly EAN was used because it was the only affordable X.400 product at that time (Source-code licenses were free for academic institutions). At the moment, the two worlds of X.400 and SMTP are moving closer together. For instance, the United States Department of Defense, one of the early forces behind the Internet, has decided that future DoD networking should be based on ISO standards, implying a migration from SMTP to X.400. As an important example of harmonisation in the other direction, X.400 users in Europe have a need to communicate with the Internet. Due to the large traffic volume between the two nets it is not enough interconnecting them with a single international gateway. The load on such a gateway would be too heavy. Direct access using local gateways is more feasible. Although the expected success of X.400 has been a bit disappointingRARE Working Group on Mail and Messaging (WG-MSG) [Page 4]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 (mainly because no good products were available), many still see the future of e-mail systems in the context of this standard. And regardless if in the long run X.400 will or will not take over the world of e-mail systems, SMTP cannot be neglected over the next ten years. Especially the simple installation procedures and the high degree of connectivity will contribute to a growing number ofRFC 822 installations in Europe and world-wide in the near future.1.1. What is X.400 ? In October 1984, the Plenary Assembly of the CCITT accepted a standard to facilitate international message exchange between subscribers to computer based store-and-forward message services. This standard is known as the CCITT X.400 series recommendations ([16], from now on called X.400(84)) and happens to be the first CCITT recommendation for a network application. It should be noted that X.400(84) is based on work done in the IFIP Working Group 6.5, and that ISO at the same time was proceeding towards a compatible document. However, the standardisation efforts of CCITT and ISO did not converge in time (not until the 1988 version), to allow the publication of a common text. X.400(84) triggered the development of software implementing (parts of) the standard in the laboratories of almost all major computer vendors and many software houses. Similarly, public carriers in many countries started to plan X.400(84) based message systems that would be offered to the users as value added services. Early implementations appeared shortly after first drafts of the standard were published and a considerable number of commercial systems are available nowadays. X.400(84) describes a functional model for a Message Handling System (MHS) and associates services and protocols. The model illustrated in Figure 1.1. defines the components of a distributed messaging system. Users in the MHS environment are provided with the capability of sending and receiving messages. Users in the context of an MHS may be humans or application processes. The User Agent (UA) is a process that makes the services of the MTS available to the user. A UA may be implemented as a computer program that provides utilities to create, send, receive and perhaps archive messages. Each UA, and thus each user, is identified by a name (each user has its own UA).RARE Working Group on Mail and Messaging (WG-MSG) [Page 5]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 ----------------------------------------------------------------- | user user Message Handling Environment| | | | | | ----------------------------------------------------------| | | | | Message Handling System || | | ---- ---- || | | |UA| |UA| || | | ---- ---- || | | | | || | | -------------------------------------------------|| | | | | | Message Transfer System ||| | | ---- | ----- ----- ||| |user-|-|UA|--|--|MTA| |MTA| ||| | | ---- | ----- ----- ||| | | | \ / ||| | | | \ / ||| | | | \ / ||| | | | \ / ||| | | | \ / ||| | | ---- | ----- ||| |user-|-|UA|--|---------|MTA| ||| | | ---- | ----- ||| | | -------------------------------------------------|| | ----------------------------------------------------------| ----------------------------------------------------------------- Fig. 1.1. X.400 functional model The Message Transfer system (MTS) transfers messages from an originating UA to a recipient UA. As implied by the Figure 1.1, data sent from UA to UA may be stored temporarily in several intermediate Message Transfer Agents (MTA), i.e., a store-and- forward mechanism is being used. An MTA forwards received messages to a next MTA or to the recipient UA. X.400(84) divides layer 7 of the OSI Reference Model into 2 sublayers, the User Agent Layer (UAL) and the Message Transfer Layer (MTL) as shown in the Figure 1.2. The MTL is involved in the transport of messages from UA to UA, using one or several MTAs as intermediaries. By consequence, routing issues are entirely dealt with in the MTL. The MTL in fact corresponds to the postal service that forwards letters consisting of an envelope and a content. Two protocols, P1 and P3, are used between the MTL entities (MTA Entity (MTAE), and Submission and Delivery Entity (SDE)) to reliably transport messages. The UAL embodies peer UA Entities (UAE), which interpret the content of a message and offer specific services to the application process. Depending on the application to be supported on top of the MTL, one of several end-RARE Working Group on Mail and Messaging (WG-MSG) [Page 6]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 to-end protocols (Pc) is used between UAEs. For electronic mail, X.400(84) defines the protocol P2 as part of the InterPersonal Messaging Service (IPMS). Conceivably other UAL protocols may be defined, e.g., a protocol to support the exchange of electronic business documents. -------------------------------------------------------------- ----- ----- UA layer |UAE|<----- P2, Pc ----------->|UAE| ----- ----- -------------------------------------------------------------- ------ ------ ----- MTA layer |MTAE|<-- P1 -->|MTAE|<-- P3-->|SDE| ------ ------ ----- -------------------------------------------------------------- xxxE = xxx Entity ; SDE = Submission & Delivery Entity -------------------------------------------------------------- Fig. 1.2. X.400 Protocols The structure of an InterPersonal Message (IPM) can be visualised as in Figure 1.3. (Note that the envelope is not a part of the IPM; it is generated by the MTL). Forwarded Message IP-message - ---------- --- ---------- - | message- |envelope| / | PDI | | | content IPM ---------- / ---------- | | - - ---------- / ---------- | | | | IPM- |heading | / |heading | | | | | body ---------- / ---------- | | | | - ----------/ ---------- | | | | | |bodypart| |bodypart| | | | | | ----------\ ---------- | | | | | ---------- \ ---------- | | | | | |bodypart| \ |bodypart| | | | | | ---------- \ ---------- | | | | | . \ | | | | | . \ | | | | | ---------- \ ---------- | | | | | |bodypart| \ |bodypart| | - - - - ---------- - ---------- - (PDI = Previous Delivery Info.) Fig. 1.3. X.400 message structure An IPM heading contains information that is specific for an interpersonal message like 'originator', 'subject', etc. Each bodypart can contain one information type, text, voice or as aRARE Working Group on Mail and Messaging (WG-MSG) [Page 7]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 special case, a forwarded message. A forwarded message consists of the original message together with Previous Delivery Information (PDI), which is drawn from the original delivery envelope. Early experience with X.400(84) showed that the standard had various shortcomings. Therefore CCITT, in parallel with ISO, corrected and extended the specification during its 1984 to 1988 study period and produced a revised standard [17], which was accepted at the 1988 CCITT Plenary Meeting [10]. Amongst others, X.400(88) differs from X.400(84) in that it defines a Message Store (MS), which can be seen as a kind of database for messages. An MS enables the end-user to run a UA locally, e.g., on a PC, whilst the messages are stored in the MS, which is co-located with the MTA. The MTA can thus always deliver incoming messages to the MS instead of to the UA. The MS can even automatically file incoming messages according to certain criteria. Other enhancements in the 88 version concern security and distribution lists.1.2. What is an RFC ? The Internet, a loosely-organised international collaboration of autonomous, interconnected networks, supports host-to-host communication through voluntary adherence to open protocols and procedures defined by Internet Standards. There are also many isolated internets, i.e., sets of interconnected networks, that are not connected to the Internet but use the Internet Standards. The architecture and technical specifications of the Internet are the result of numerous research and development activities conducted over a period of two decades, performed by the network R&D community, by service and equipment vendors, and by government agencies around the world. In general, an Internet Standard is a specification that is stable and well-understood, is technically competent, has multiple, independent, and interoperable implementations with operational experience, enjoys significant public support, and is recognisably useful in some or all parts of the Internet. The principal set of Internet Standards is commonly known as the "TCP/IP protocol suite". As the Internet evolves, new protocols and services, in particular those for Open Systems Interconnection (OSI), have been and will be deployed in traditional TCP/IP environments, leading to an Internet that supports multiple protocol suites. The following organisations are involved in setting Internet standards. Internet standardisation is an organised activity of the InternetRARE Working Group on Mail and Messaging (WG-MSG) [Page 8]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 Society (ISOC). The ISOC is a professional society that is concerned with the growth and evolution of the world-wide Internet, with the way in which the Internet is and can be used, and with the social, political, and technical issues that arise as a result. The Internet Engineering Task Force (IETF) is the primary body developing new Internet Standard specifications. The IETF is composed of many Working Groups, which are organised into areas, each of which is co-ordinated by one or more Area Directors. The Internet Engineering Steering Group (IESG) is responsible for technical management of IETF activities and the approval of Internet standards specifications, using well-defined rules. The IESG is composed of the IETF Area Directors, some at-large members, and the chairperson of the IESG/IETF. The Internet Architecture Board (IAB) has been chartered by the Internet Society Board of Trustees to provide quality control and process appeals for the standards process, as well as external technical liaison, organizational oversight, and long-term architectural planning and research. Any individual or group (e.g., an IETF or RARE working group) can submit a document as a so-called Internet Draft. After the document is proven stable, the IESG may turn the Internet-Draft into a "Requests For Comments" (RFC). RFCs cover a wide range of topics, from early discussion of new research concepts to status memos about the Internet. All Internet Standards (STDs) are published as RFCs, but not all RFCs specify standards. Another sub-series of the RFCs are the RARE Technical Reports (RTRs). As an example, this tutorial also started out as an Internet-Draft. After almost one year of discussions and revisions it was approved by the IESG as an Informational RFC. Once a document is assigned an RFC number and published, that RFC is never revised or re-issued with the same number. Instead, a revision will lead to the document being re-issued with a higher number indicating that an older one is obsoleted.1.3. What isRFC 822 ? STD 11,RFC 822 defines a standard for the format of Internet text messages. Messages consist of lines of text. No special provisions are made for encoding drawings, facsimile, speech, or structured text. No significant consideration has been given to questions of data compression or to transmission and storage efficiency, and the standard tends to be free with the number of bits consumed. ForRARE Working Group on Mail and Messaging (WG-MSG) [Page 9]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 example, field names are specified as free text, rather than special terse codes. A general "memo" framework is used. That is, a message consists of some information in a rigid format (the 'headers'), followed by the main part of the message (the 'body'), with a format that is not specified in STD 11,RFC 822. It does define the syntax of several fields of the headers section; some of these fields must be included in all messages. STD 11,RFC 822 is used in conjunction with a number of different message transfer protocol environments (822-MTSs). - SMTP Networks: On the Internet and other TCP/IP networks, STD 11,RFC 822 is used in conjunction with two other standards: STD 10,RFC 821, also known as Simple Mail Transfer Protocol (SMTP) [1], and RFCs 1034 and 1035 which specify the Domain Name System [3]. - UUCP Networks: UUCP is the UNIX to UNIX CoPy protocol, which is usually used over dialup telephone networks to provide a simple message transfer mechanism. - BITNET: Some parts of Bitnet and related networks use STD 11,RFC 822 related protocols, with EBCDIC encoding. - JNT Mail Networks: A number of X.25 networks, particularly those associated with the UK Academic Community, use the JNT (Joint Network Team) Mail Protocol, also known as Greybook. STD 11,RFC 822 is based on the assumption that there is an underlying service, which inRFC 1327 is called the 822-MTS service. The 822-MTS service provides three basic functions: 1. Identification of a list of recipients. 2. Identification of an error return address. 3. Transfer of anRFC 822 message. It is possible to achieve 2) within theRFC 822 header. Some 822- MTS protocols, in particular SMTP, can provide additional functionality, but as these are neither mandatory in SMTP, nor available in other 822-MTS protocols, they are not considered here. Details of aspects specific to two 822-MTS protocols are given in Appendices B and C ofRFC 1327. AnRFC 822 message consists of a header, and content which is uninterpreted ASCII text. The header is divided into fields, which are the protocol elements. Most of these fields are analogous to P2 heading fields, although some are analogous to MTS Service Elements.RARE Working Group on Mail and Messaging (WG-MSG) [Page 10]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 19931.4. What isRFC 1327 ? There is a large community using STD 11,RFC 822 based protocols for mail services, who will wish to communicate with users of the InterPersonal Messaging Service (IPMS) provided by X.400 systems, and the other way around. This will also be a requirement in cases whereRFC 822 communities intend to make a transition to use X.400 (or the other way around, which also happens), as conversion will be needed to ensure a smooth service transition. The basic function of a mail gateway can be described as follows: receive a mail from one mail world, translate it into the formats of the other mail world and send it out again using the routing rules and protocols of that other world. Especially if a message crosses more than one gateway, it is important that all gateways have the same understanding of how things should be mapped. A simple example of what could go wrong otherwise is the following: A sends a message to B through a gateway and B's reply to A is being routed through another gateway. If the two gateways don't use the same mappings, it can be expected that the From and To addresses in the original mail and in the answer don't match, which is, to say the least, very confusing for the end- users (consider what happens if automated processes communicate via mail). More serious things can happen to addresses if a message crosses more than one gateway on its way from the originator to the recipient. As a real-life example, consider receiving a message from: Mary Plork <MMP_+a_ARG_+lMary_Plork+r%MHS+d_A0CD8A2B01F54FDC- A0CB9A2B03F53FDC%ARG_Incorporated@argmail.com> This is not what you would call user-friendly addressing....RFC 1327 describes a set of mappings that will enable a more transparent interworking between systems operating X.400 (both 84 and 88) and systems usingRFC 822, or protocols derived from STD 11,RFC 822.RFC 1327 describes all mappings in term of X.400(88). It defines how these mappings should be applied to X.400(84) systems in itsAppendixG. Some words about the history ofRFC 1327: It started out in June 1986, whenRFC 987 defined for X.400(84) whatRFC 1327 defines for X.400(84 and 88).RFC 1026 specified a number of additions and corrections toRFC 987. In December 1989,RFC 1138, which had a very short lifetime, was the first one to deal with X.400(88). It was obsoleted byRFC 1148 in March 1990. Finally, in May 1992,RFC 1327 obsoleted all of its ancestors.RARE Working Group on Mail and Messaging (WG-MSG) [Page 11]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 19932. Service Elements BothRFC 822 and X.400 messages consist of certain service elements (such as 'originator' and 'subject'). As long as a message stays within its own world, the behaviour of such service elements is well defined. An important goal for a gateway is to maintain the highest possible service level when a message crosses the boundary between the two mail worlds. When a user originates a message, a number of services are available.RFC 1327 describes, for each service elements, to what extent it is supported for a recipient accessed through a gateway. There are three levels of support: - Supported: Some of the mappings are quite straight-forward, such as '822.Subject:' <-> 'IPMS.Subject'. - Not supported: There may be a complete mismatch: certain service elements exist only in one of the two worlds (e.g., interpersonal notifications). - Partially supported: When similar service elements exist in both worlds, but with slightly different interpretations, some tricks may be needed to provide the service over the gateway border. Apart from mapping between the service elements, a gateway must also map the types and values assigned to these service elements. Again, this may in certain cases be very simple, e.g., 'IA5 -> ASCII'. The most complicated example is mapping address spaces. The problem is that address spaces are not something static that can be defined withinRFC 1327. Address spaces change continuously, and they are defined by certain addressing authorities, which are not always parallel in theRFC 822 and the X.400 world. A valid mapping between two addresses assumes however that there is 'administrative equivalence' between the two domains in which the addresses exist (see also [13]). The following basic mappings are defined inRFC 1327. When going fromRFC 822 to X.400, anRFC 822 message and the associated 822- MTS information is always mapped into an IPM (MTA, MTS, and IPMS Services). Going from X.400 toRFC 822, anRFC 822 message and the associated 822-MTS information may be derived from: - A Report (MTA, and MTS Services) - An InterPersonal Notification (IPN) (MTA, MTS, and IPMS services)RARE Working Group on Mail and Messaging (WG-MSG) [Page 12]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 - An InterPersonal Message (IPM) (MTA, MTS, and IPMS services) Probes (MTA Service) have no equivalent in STD 10,RFC 821 or STD 11,RFC 822 and are thus handled by the gateway. The gateway's Probe confirmation should be interpreted as if the gateway were the final MTA to which the Probe was sent. Optionally, if the gateway usesRFC821 as an 822-MTS, it may use the results of the 'VRFY' command to test whether it would be able to deliver (or forward) mail to the mailbox under probe. MTS Messages containing Content Types other than those defined by the IPMS are not mapped by the gateway, and should be rejected at the gateway. Some basic examples of mappings between service elements are listed below. Service elements:RFC 822 X.400 ------------------------------------------------ Reply-To: IPMS.Heading.reply-recipients Subject: IPMS.Heading.subject In-Reply-To: IPMS.Heading.replied-to-ipm References: IPMS.Heading.related-IPMs To: IPMS.Heading.primary-recipients Cc: IPMS.Heading.copy-recipients Service element types:RFC 822 X.400 ------------------------------------------------ ASCII PrintableString Boolean Boolean Service element values:RFC 822 X.400 ------------------------------------------------ oh_dear oh(u)dear False 00000000 There are some mappings between service elements that are rather tricky and important enough to mention in this tutorial. These are the mappings of origination-related headers and some envelope fields:RARE Working Group on Mail and Messaging (WG-MSG) [Page 13]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993RFC 822 -> X.400: - If Sender: is present, Sender: is mapped to IPMS.Heading.originator, and From: is mapped to IPMS.Heading.authorizing-users. If not, From: is mapped to IPMS.Heading.originator. X.400 ->RFC 822 - If IPMS.Heading.authorizing-users is present, IPMS.Heading.originator is mapped to Sender:, and IPMS.Heading.authorizing-users is mapped to From: . If not, IPMS.Heading.originator is mapped to From:. Envelope attributes -RFC 1327 doesn't define how to map the MTS.OriginatorName and the MTS.RecipientName (often referred to as the P1.originator and P1.recipient), since this depends on which underlying 822- MTS is used. In the very common case thatRFC 821 (SMTP) is used for this purpose, the mapping is normally as follows: MTS.Originator-name <-> MAIL FROM: MTS.Recipient-name <-> RCPT TO: For more details, refer toRFC 1327, chapters 2.2 and 2.3.3. Address mapping As address mapping is often considered the most complicated part of mapping between service element values, this subject is given a separate chapter in this tutorial. BothRFC 822 and X.400 have their own specific address formats.RFC822 addresses are text strings (e.g., "plork@tlec.nl"), whereas X.400 addresses are binary encoded sets of attributes with values. Such binary addresses can be made readable for a human user by a number of notations; for instance: C=zz ADMD=ade PRMD=fhbo O=a bank S=plork G=mary The rest of this chapter deals with addressing issues and mappings between the two address forms in more detail.RARE Working Group on Mail and Messaging (WG-MSG) [Page 14]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 19933.1. X.400 addresses As already stated above, an X.400 address is modelled as a set of attributes. Some of these attributes are mandatory, others are optional. Each attribute has a type and a value, e.g., the Surname attribute has type IA5text, and an instance of this attribute could have the value 'Kille'. Attributes are divided into Standard Attributes (SAs) and Domain Defined Attributes (DDAs). X.400 defines four basic forms of addresses ([17], 18.5), of which the 'Mnemonic O/R Address' is the form that is most used, and is the only form that is dealt with in this tutorial. This is roughly the same address format as what in the 84 version was known as 'O/R names: form 1, variant 1' ([16] 3.3.2).3.1.1. Standard Attributes Standard Attributes (SAs) are attributes that all X.400 installations are supposed to 'understand' (i.e., use for routing), for example: 'country name', 'given name' or 'organizational unit'. The most commonly used SAs in X.400(84) are: surName (S) givenName (G) initials (I*) (Zero or more) generationQualifier (GQ) OrganizationalUnits (OU1 OU2 OU3 OU4) OrganizationName (O) PrivateDomainName (PRMD) AdministrationDomainName (ADMD) CountryName (C) The combination of S, G, I* and GQ is often referred to as the PersonalName (PN). Although there is no hierarchy (of addressing authorities) defined by the standards, the following hierarchy is considered natural: PersonalName < OU4 < OU3 < OU2 < OU1 < O < P < A < C In addition to the SAs listed above, X.400(88) defines some extra attributes, the most important of which is Common Name (CN) CN can be used instead of or even together with PN. The problem in X.400(84) was that PN (S G I* GQ) was well suited to represent persons, but not roles and abstract objects, such as distributionRARE Working Group on Mail and Messaging (WG-MSG) [Page 15]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 lists. Even though postmaster clearly is a role, not someone's real surname, it is quite usual in X.400(84) to address a postmaster with S=postmaster. In X.400(88), the same postmaster would be addressed with CN=postmaster . The attributes C and ADMD are mandatory (i.e., they must be present), and may not be empty. At least one of the attributes PRMD, O, OU, PN and CN must be present. PRMD and ADMD are often felt to be routing attributes that don't really belong in addresses. As an example of how such address attributes can be used for the purpose of routing, consider two special values for ADMD: - ADMD=0; (zero) should be interpreted as 'the PRMD in this address is not connected to any ADMD' - ADMD= ; (single SPACE) should be interpreted as 'the PRMD in this address is reachable via any ADMD in this country'. It is expected that ISO will express this 'any' value by means of a missing ADMD attribute in future versions of MOTIS. This representation can uniquely identify the meaning 'any', as a missing or empty ADMD field as such is not allowed. Addresses are defined in X.400 using the Abstract Syntax Notation One (ASN.1). X.409 defines how definitions in ASN.1 should be encoded into binary format. Note that the meaning, and thus the ASN.1 encoding, of a missing attribute is not the same as that of an empty attribute. In addressing, this difference is often represented as follows: - PRMD=; means that this attribute is present in the address, but its value is empty. Since this is not very useful, it's hardly ever used. The only examples the author knows of were caused by mail managers who should have had this tutorial before they started defining their addresses :-) - PRMD=@; means that this attribute is not present in the address. {NB. This is only necessary if an address notation (see 3.1.3) requires that every single attribute in the hierarchy is somehow listed. Otherwise, a missing attribute can of course be represented by simply not mentioning it. This means that this syntax is mostly used in mapping rules, not by end users.} Addresses that only contain SAs are often referred to as Standard Attribute Addresses (SAAs).RARE Working Group on Mail and Messaging (WG-MSG) [Page 16]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 19933.1.2. Domain Defined Attributes Domain Defined Attributes (DDAs) can be used in addition to Standard Attributes. An instance of a DDA consists of a type and a value. DDAs are meant to have a meaning only within a certain context (originally this was supposed to be the context of a certain management domain, hence the name DDA), such as a company context. As an example, a company might want to define a DDA for describing internal telephone numbers: DDA type=phone value=9571. A bit tricky is the use of DDAs to encode service element types or values that are only available on one side of a service gateway. The most important examples of such usage are defined in:RFC 1327 (e.g., DDA type=RFC-822 value=u(u)ser(a)isode.com)RFC 1328 (e.g., DDA type=CommonName value=mhs-discussion-list) Addresses that contain both SAs and DDAs are often referred to as DDA addresses.3.1.3. X.400 address notation X.400 only prescribes the binary encoding of addresses, it doesn't standardise how such addresses should be written on paper or what they should look like in a user interface on a computer screen. There exist a number of recommendations for X.400 address representation though. - JTC proposed an annex to CCITT Rec. F.401 and ISO/IEC 10021-2, called 'Representation of O/R addresses for human usage'. According to this proposal, an X.400 address would look as follows: G=jo; S=plork; O=a bank; OU1=owe; OU2=you; P=fhbo; A=ade; C=zz Note that in this format, the order of O and the OUs is exactly the opposite of what one would expect intuitively (the attribute hierarchy is increasing from left to right, except for the O and OUs, where it's right to left. The reasoning behind this is that this sequence is following the example of a postal address). This proposal has been added (as a recommendation) to the 1992 version of the standards. - Following what was originally used in the DFN-EAN software, most EAN versions today use an address representation similar to the JTC proposal, with a few differences:RARE Working Group on Mail and Messaging (WG-MSG) [Page 17]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 - natural ordering for O and OUs - no numbering of OUs. - allows writing ADMD and PRMD instead of A and P The address in the example above could, in EAN, be represented as: G=jo; S=plork; OU=you; OU=owe; O=a bank; PRMD=fhbo; ADMD=ade; C=zz This DFN-EAN format is still often referred to as _the_ 'readable format'. - The RARE Working Group on Mail and Messaging, WG-MSG, has made a recommendation that is very similar to the DFN-EAN format, but with the hierarchy reversed. Further, ADMD and PRMD are used instead of A and P. This results in the address above being represented as: C=zz; ADMD=ade; PRMD=fhbo; O=a bank; OU=owe; OU=you; S=plork; G=jo This format is recognised by most versions of the EAN software. In the R&D community, this is one of the most popular address representations for business cards, letter heads, etc. It is also the format that will be used for the examples in this tutorial. (NB. The syntax used here for describing DDAs is as follows: DD.'type'='value', e.g., DD.phone=9571) -RFC 1327 defines a slash separated address representation: /G=jo/S=plork/OU=you/OU=owe/O=a bank/P=fhbo/A=ade/C=zz/ Not only is this format used by the PP software, it is also widespread for business cards and letter heads in the R&D community. -RFC 1327 finally defines yet another format for X.400 _domains_ (not for human users): OU$you.OU$owe.O$a bank.P$fhbo.A$ade.C$zz The main advantage of this format is that it is better machine- parseble than the others, which also immediately implies its main disadvantage: it is barely readable for humans. Every attribute within the hierarchy should be listed, thus a missing attribute must be represented by the '@' sign (e.g., $a bank.P$@.A$ade.C$zz). - Paul-Andre Pays (INRIA) has proposed a format that combines the readability of the JTC format with the parsebility of theRFC 1327 domain format. Although a number of operational tools within the GO-RARE Working Group on Mail and Messaging (WG-MSG) [Page 18]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 MHS community are already based on (variants of) this proposal, its future is still uncertain.3.2.RFC 822 addresses AnRFC 822 address is an ASCII string of the following form: localpart@domainpart "domainpart" is sub-divided into domainpart = sdom(n).sdom(n-1)....sdom(2).sdom(1).dom "sdom" stands for "subdomain", "dom" stands for "top-level-domain". "localpart" ;is normally a login name, and thus typically is a surname or an abbreviation for this. It can also designate a local distribution list. The hierarchy (of addressing authorities) in anRFC 822 address is as follows: localpart < sdom(n) < sdom(n-1) <...< dom Some virtual real-life examples: joemp@tlec.nl tsjaka.kahn@walhalla.diku.dk a13_vk@cs.rochester.edu In the above examples, 'nl', 'dk', and 'edu' are valid, registered, top level domains. Note that some networks that have their own addressing schemes are also reachable by way of 'RFC822-like' addressing. Consider the following addresses: oops!user (a UUCP address) V13ENZACC@CZKETH5A (a BITNET address) These addresses can be expressed inRFC 822 format: user@oops.uucp V13ENZACC@CZKETH5A.BITNET Note that the domains '.uucp' and '.bitnet' have no registered Internet routing. Such addresses must always be routed to a gateway (how this is done is outside the scope of this tutorial). As for mapping such addresses to X.400, there is no direct mappingRARE Working Group on Mail and Messaging (WG-MSG) [Page 19]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 defined between X.400 on the one hand and UUCP and BITNET on the other, so they are normally mapped toRFC 822 style first, and then to X.400 if needed.3.3.RFC 1327 address mapping Despite the difference in address formats, the address spaces defined byRFC 822 and X.400 are quite similar. The most important parallels are: - both address spaces are hierarchical - top level domains and country codes are often the same - localparts and surnames are often the same This similarity can of course be exploited in address mapping algorithms. This is also done inRFC 1327 (NB only in the exception mapping algorithm. See chapter 3.3.2). Note that the actual mapping algorithm is much more complicated than shown below. For details, seeRFC 1327, chapter 4.3.3.1. Default mapping The defaultRFC 1327 address mapping can be visualised as a function with input and output parameters: address information of the gateway performing the mapping | v +-----------------+RFC 822 address <--->| address mapping | <---> X.400 address +-----------------+ I.e., to map an address from X.400 toRFC 822 or vice versa, the only extra input needed is the address information of the local gateway.3.3.1.1. X.400 ->RFC 822 There are two kinds of default address mapping from X.400 toRFC 822: one to map a real X.400 address toRFC 822, and another to decode anRFC 822 address that was mapped to X.400 (i.e., to reverse the defaultRFC 822 -> X.400 mapping). To map a real X.400 address toRFC 822, the slash separated notation of the X.400 address (see chapter 3.1.) is mapped to 'localpart', and the localRFC 822 domain of the gateway that performs the mapping is used as the domain part. As an example, the gateway 'gw.switch.ch' would perform the following mappings:RARE Working Group on Mail and Messaging (WG-MSG) [Page 20]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 C=zz; ADMD=ade; PRMD=fhbo; O=tlec; S=plork; -> /C=zz/ADMD=ade/PRMD=fhbo/O=tlec/S=plork/@gw.switch.ch C=zz; ADMD=ade; PRMD=fhbo; O=a bank; S=plork-> "/C=zz/ADMD=ade/PRMD=fhbo/O=a bank/S=plork/"@gw.switch.ch The quotes in the second example are mandatory if the X.400 address contains spaces, otherwise the syntax rules for theRFC 822 localpart would be violated. This default mapping algorithm is generally referred to as 'left- hand-side encoding'. To reverse the defaultRFC 822 -> X.400 mapping (see chapter 3.3.1.2): if the X.400 address contains a DDA of the typeRFC-822, the SAs can be discarded, and the value of this DDA is the desiredRFC 822 address (NB. Some characters in the DDA value must be decoded first. See chapter 3.3.1.2.). For example, the gateway DD.RFC-822=bush(a)dole.us; C=nl; ADMD=tlec; PRMD=GW -> bush@dole.us3.3.1.2.RFC 822 -> X.400 There are also two kinds of default address mapping fromRFC 822 to X.400: one to map a realRFC 822 address to X.400, and another to decode an X.400 address that was mapped toRFC 822 (i.e., to reverse the default X.400 ->RFC 822 mapping). To map a realRFC 822 address to X.400, theRFC 822 address is encoded in a DDA of typeRFC-822 , and the SAs of the local gateway performing the mapping are added to form the complete X.400 address. This mapping is generally referred to as 'DDA mapping'. As an example, the gateway 'C=nl; ADMD=tlec; PRMD=GW' would perform the following mapping: bush@dole.us -> DD.RFC-822=bush(a)dole.us; C=nl; ADMD=tlec; PRMD=GW As for the encoding/decoding ofRFC 822 addresses in DDAs, it is noted thatRFC 822 addresses may contain characters (@ ! % etc.) that cannot directly be represented in a DDA. DDAs are of the restricted character set type 'PrintableString', which is a subset of IA5 (=ASCII). Characters not in this set need a special encoding. Some examples (For details, refer toRFC 1327, chapter 3.4.):RARE Working Group on Mail and Messaging (WG-MSG) [Page 21]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 100%name@address -> DD.RFC-822;=100(p)name(a)address u_ser!name@address -> DD.RFC-822;=u(u)ser(b)name(a)address To decode an X.400 address that was mapped toRFC 822: if theRFC 822 address has a slash separated representation of a complete X.400 mnemonic O/R address in its localpart, that address is the result of the mapping. As an example, the gateway 'gw.switch.ch' would perform the following mapping: /C=zz/ADMD=ade/PRMD=fhbo/O=tlec/S=plork/G=mary/@gw.switch.ch -> C=zz; ADMD=ade; PRMD=fhbo; O=tlec; S=plork; G=mary3.3.2. Exception mapping according to mapping tables Chapter 3.3.1. showed that it is theoretically possible to useRFC1327 with default mapping only. Although this provides a very simple, straightforward way to map addresses, there are some very good reasons not to useRFC 1327 this way: -RFC 822 users are used to writing simple addresses of the form 'localpart@domainpart'. They often consider X.400 addresses, and thus also the left-hand-side encoded equivalents, as unnecessarily long and complicated. They would rather be able to address an X.400 user as if she had a 'normal'RFC 822 address. For example, take the mapping C=zz; ADMD=ade; PRMD=fhbo; O=tlec; S=plork; -> /C=zz/ADMD=ade/PRMD=fhbo/O=tlec/S=plork/@gw.switch.ch from chapter 3.3.1.1.RFC 822 users would find it much more 'natural' if this address could be expressed inRFC 822 as: plork@tlec.fhbo.ade.nl - X.400 users are used to using X.400 addresses with SAs only. They often consider DDA addresses as complicated, especially if they have to encode the special characters, @ % ! etc, manually. They would rather be able to address anRFC 822 user as if he had a 'normal' X.400 address. For example, take the mapping bush@dole.us -> DD.RFC-822=bush(a)dole.us; C=nl; ADMD= ; PRMD=tlec; O=gateway from chapter 3.3.1.2. X.400 users would find it much moreRARE Working Group on Mail and Messaging (WG-MSG) [Page 22]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 'natural' if this address could be expressed in X.400 as: C=us; ADMD=dole; S=bush - Many organisations are using bothRFC 822 and X.400 internally, and still want all their users to have a simple, unique address in both mail worlds. Note that in the default mapping, the mapped form of an address completely depends on which gateway performed the mapping. This also results in a complication of a more technical nature: - The tricky 'third party problem'. This problem need not necessarily be understood to read the rest of this chapter. If it looks too complicated, please feel free to skip it until you are more familiar with the basics. The third party problem is a routing problem caused by mapping. As an example for DDA mappings (the example holds just as well for left-hand-side encoding), consider the following situation (see Fig. 3.1.):RFC 822 user X in country A sends a message to two recipients:RFC 822 user Y, and X.400 user Z, both in country B: From: X@A To: Y@B , /C=B/.../S=Z/@GW.A Since the gateway in country A maps all addresses in the message, Z will see both X's and Y's address as DDA-encodedRFC 822 addresses, with the SAs of the gateway in country A: From: DD.RFC-822=X(a)A; C=A;....;O=GW To: DD.RFC-822=Y(a)B; C=A;....;O=GW , C=B;...;S=ZRARE Working Group on Mail and Messaging (WG-MSG) [Page 23]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 | ------------ --------- | |X:RFC 822|<------->|gateway| | ------------ --------- | A | ^ \ | | \--------------------------------------------- | | /--------------------------------------------- / | | | B | v | | ----------- | | |Z: X.400 | | | ----------- | | . | | . | | . | | . | | . | v v | ------------ --------- | |Y:RFC 822|<........|gateway| | ------------ --------- Fig. 3.1 The third party problem Now if Z wants to 'group reply' to both X and Y, his reply to Y will be routed over the gateway in country A, even though Y is located in the same country: From: C=B;...;S=Z To: DD.RFC-822=Y(a)B; C=A;....;O=GW , DD.RFC-822=X(a)A; C=A;....;O=GW The best way to travel for a message from Z to Y would of course have been over the gateway in country B: From: C=B;...;S=Z To: DD.RFC-822=Y(a)B; C=B;....;O=GW , DD.RFC-822=X(a)A; C=A;....;O=GW The third party problem is caused by the fact that routing information is mapped into addresses. Ideally, the third party problem shouldn't exist. After all, address mapping affects addresses, and an address is not a route.... The reality is different however. For instance, veryRARE Working Group on Mail and Messaging (WG-MSG) [Page 24]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 few X.400 products are capable to route messages on the contents of a DDA (actually, onlyRFC 1327 gateways will be able to interpret this type of DDA, and who says that the reply will pass a local gateway on its route back?). Similar limitations hold for the other direction: anRFC 822 based mailer is not even allowed (see [5]) to make routing decisions of the content of a left-hand-side encoded X.400 address if the domain part is not its own. So in practice, addressing and (thus also mapping) will very well affect routing. To make mapping between addresses more user friendly, and to avoid the problems shown above,RFC 1327 allows for overruling the default left-hand-side encoding and DDA mapping algorithms. This is done by specifying associations (mapping rules) between certain domainparts and X.400 domains. An X.400 domain (for our purposes; CCITT has a narrower definition...) consists of the domain-related SAs of a Mnemonic O/R address (i.e., all SAs except PN and CN). The idea is to use the similarities between both address spaces, and directly map similar address parts onto each other. If, for the domain in the address to be mapped, an explicit mapping rule can be found, the mapping is performed between: localpart <-> PersonalName domainpart <-> X.400 domain The address information of the gateway is only used as an input parameter if no mapping rule can be found, i.e., if the address mapping must fall back to its default algorithm. The complete mapping function can thus be visualised as follows: address information of the gateway performing the mapping | v +-----------------+RFC 822 address <--->| address mapping | <---> X.400 address +-----------------+ ^ | domain associations (mapping rules)3.3.2.1. PersonalName and localpart mapping Since the mapping between these address parts is independent of the mapping rules that are used, and because it follows a simple, two- way algorithmic approach, this subject is discussed in a separate sub-chapter first.RARE Working Group on Mail and Messaging (WG-MSG) [Page 25]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 The X.400 PersonalName consists of givenName, initials, and surName.RFC 1327 assumes that generationQualifier is not used. To map a localpart to an X.400 PN, the localpart is scanned for dots, which are considered delimiters between the components of PN, and also between single initials. In order not to put too much detail in this tutorial, only a few examples are shown here. For the detailed algorithm, seeRFC 1327, chapter 4.2.1. Marshall.Rose <-> G=Marshall;S=Rose M.T.Rose <-> I=MT;S=Rose Marshall.M.T.Rose <-> G=Marshall;I=MT;S=Rose To map an X.400 PN to anRFC 822 localpart, take the non-empty PN attributes, put them into their hierarchical order (G I* S), and connect them with periods. Some exceptions are caused by the fact that left-hand-side encoding can also be mixed with exception mapping. This is shown in more detail in the following sub-chapters.3.3.2.2. X.400 domain and domainpart mapping A mapping rule associates two domains: an X.400 domain and anRFC 822 domain. The X.400 domain is written in theRFC 1327 domain notation (See 3.1.3.), so that both domains have the same hierarchical order. The domains are written on one line, separated by a '#' sign. For instance: arcom.ch#ADMD$arcom.C$ch# PRMD$tlec.ADMD$ade.C$nl#tlec.nl# A mapping rule must at least contain a top level domain and a country code. If an address must be mapped, a mapping rule with the longest domain match is sought. The associated domain in the mapping rule is used as the domain of the mapped address. The remaining domains are mapped one by one following the natural hierarchy. Concrete examples are shown in the following subchapters.3.3.2.2.1. X.400 ->RFC 822 As an example, assume the following mapping rule is defined: PRMD$tlec.ADMD$ade.C$nl#tlec.nl#RARE Working Group on Mail and Messaging (WG-MSG) [Page 26]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 Then the address C=nl; ADMD=ade; PRMD=tlec; O=you; OU=owe; S=plork S OU O PRMD ADMD Country | | | | | | plork owe you tlec ade nl would be mapped as follows. The Surname 'plork' is mapped to the localpart 'plork', see chapter 3.3.2.1. The domain localpart | sdom3 | | sdom2 | | | sdom1 | | | | top-level-domain | | | | | plork@ tlec.nl The remaining SAs (O and one OU) are mapped one by one following the natural hierarchy: O is mapped to sdom2, OU is mapped to sdom3: localpart | sdom3 | | sdom2 | | | sdom1 | | | | top-level-domain | | | | | plork@owe.you.tlec.nl Thus the mapped address is: plork@owe.you.tlec.nl The table containing the listing of all such mapping rules, which is distributed to all gateways world-wide, is normally referred to as 'mapping table 1'. Other commonly used filenames (also depending on which software your are using) are: 'or2rfc' 'mapping 1' 'map1' 'table 1' 'X2R' As already announced, there is an exceptional case were localpart and PN are not directly mapped onto each other: sometimes it is necessary to use the localpart for other purposes. If the X.400 address contains attributes that would not allow for the simple mapping:RARE Working Group on Mail and Messaging (WG-MSG) [Page 27]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 localpart <-> PersonalName domainpart <-> X.400 domain (e.g., spaces are not allowed in anRFC 822 domain, GQ and CN cannot be directly mapped into localpart, DDAs of another type thanRFC-822), such attributes, together with the PN, are left-hand-side encoded. The domainpart must still be mapped according to the mapping rule as far as possible. This probably needs some examples: C=nl; ADMD=ade; PRMD=tlec; O=owe; OU=you; S=plork; GQ=jr -> /S=plork/GQ=jr/@you.owe.tlec.nl C=nl; ADMD=ade; PRMD=tlec; O=owe; OU=spc ctr; OU=u; S=plork -> "/S=plork/OU=u/OU=spc ctr/"@owe.tlec.nl Note that in the second example, 'O=owe' is still mapped to a subdomain following the natural hierarchy. The problems start with the space in 'OU=spc ctr'.3.3.2.2.2.RFC 822 -> X.400 As an example, assume the following mapping rule is defined: tlec.nl#PRMD$tlec.ADMD$ade.C$nl# Then the address 'plork@owe.you.tlec.nl' : localpart | sdom3 | | sdom2 | | | sdom1 | | | | top-level-domain | | | | | plork@owe.you.tlec.nl would be mapped as follows. The localpart 'plork' is mapped to 'S=plork', see chapter 3.3.2.1. The domain 'tlec.nl' is mapped according to the mapping rule: S OU OU O PRMD ADMD Country | | | | plork tlec ade nl The remaining domains (owe.you) are mapped one by one following theRARE Working Group on Mail and Messaging (WG-MSG) [Page 28]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 natural hierarchy: sdom2 is mapped to O, sdom3 is mapped to OU: S OU OU O PRMD ADMD Country | | | | | | plork | | tlec ade nl owe you Thus the mapped address is (in a readable notation): C=nl; ADMD=ade; PRMD=tlec; O=you; OU=owe; S=plork Had there been any left-hand-side encoded SAs in the localpart that didn't represent a complete mnemonic O/R address, the localpart would be mapped to those SAs. E.g., "/S=plork/GQ=jr/OU=u/OU=spc ctr/"@owe.tlec.nl -> C=nl; ADMD=ade; PRMD=tlec; O=owe; OU=space ctr; OU=u; S=plork; GQ=jr This is necessary to reverse the special use of localpart to left- hand-side encode certain attributes. See 3.3.2.2.1. You might ask yourself by now why such rules are needed at all. Why don't we just use map1 in the other direction? The problem is that a symmetric mapping function (a bijection) would indeed be ideal, but it's not feasible. Asymmetric mappings exist for a number of reasons: - To make sure that uucp addresses etc. get routed over local gateways. - Preferring certain address forms, while still not forbidding others to use another form. Examples of such reasons are: - Phasing out old address forms. - If anRFC 822 address is mapped to ADMD= ; it means that the X.400 mail can be routed over any ADMD in that country. One single ADMD may of course send out an address containing: ADMD=ade; . It must also be possible to map such an address back. So we do need mapping rules fromRFC 822 to X.400 too. The table containing the listing of all such mapping rules, which is distributed to all gateways world-wide, is normally referred to as on which software your are using) are:RARE Working Group on Mail and Messaging (WG-MSG) [Page 29]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 'rfc2or' 'mapping 2' 'map2' 'table 2' 'R2X' If theRFC 822 localpart and/or domainpart contain characters that would not immediately fit in the value of a PN attribute (! % _), the mapping algorithm falls back to DDA mapping. In this case, the SAs that will be used are still determined by mapping the domainpart according to the mapping rule. In our case: 100%user@work.tlec.nl -> DD.RFC-822=100(p)user(a)work.tlec.nl; C=nl; ADMD=ade; PRMD=tlec; O=work If no map2 rule can be found, a third table of rules is scanned: the gateway table. This table has the same syntax as mapping table 2, but its semantics are different. First of all, a domain that only has an entry in the gateway table is always mapped into anRFC 822 DDA. For a domain that is purelyRFC 822 based, but whose mail may be relayed over an X.400 network, the gateway table associates with such a domain the SAs of the gateway to which the X.400 message should be routed. That gateway will then be responsible for gatewaying the message back into theRFC 822 world. E.g., if we have the gateway table entry: gov#PRMD$gateway.ADMD$Internet.C$us# (and we assume that no overruling map2 rule for the top level domain 'gov' exists), this would force all gateways to perform the following mapping: bush@dole.gov -> DD.RFC-822=bush(a)dole.gov; C=us; ADMD=Internet; PRMD=gateway This is very similar to the default DDA mapping, except the SAs are those of a gateway that has declared to be responsible for a certainRFC 822 domain, not those of the local gateway. And thus, this mechanism helps avoid the third party problem discussed in chapter 3.2.2. The table containing the listing of all such gateway rules, which is distributed to all gateways world-wide, is normally referred to as the 'gateway table'. Other commonly used filenames (also depending onRARE Working Group on Mail and Messaging (WG-MSG) [Page 30]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 which software your are using) are: 'rfc1148gate' {From the predecessor ofRFC 1327,RFC 1148} 'gate table' 'GW' Only when no rule at all (map2 or gateway rule) is defined for a domain, the algorithm falls back to the default DDA mapping as described in 3.3.1.2.3.4. Table co-ordination As already stated, the use of mapping tables will only function smoothly if all gateways in the world use the same tables. On the global level, the collection and distribution ofRFC 1327 address mapping tables is co-ordinated by the MHS Co-ordination Service: SWITCH Head Office MHS Co-ordination Service Limmatquai 138 CH-8001 Zurich, Europe Tel. +41 1 268 1550 Fax. +41 1 268 1568RFC 822: project-team@switch.ch X.400: C=ch;ADMD=arcom;PRMD=switch;O=switch;S=project-team; The procedures for collection and distribution of mapping rules can be found on the MHS Co-ordination Server, in the directory "/procedures".Appendix D describes how this server can be accessed. If you want to define mapping rules for your own local domain, you can find the right contact person in your country or network (the gateway manager) on the same server, in the directory "/mhs- services".3.5. Local additions Since certain networks want to define rules that should only be used within their networks, such rules should not be distributed world- wide. Consider two networks that both want to reach the old top- level-domain 'arpa' over their local gateway. They would both like to use a mapping 2 rule for this purpose: TLec in NL: arpa#PRMD$gateway.ADMD$tlec.C$nl# SWITCH in CH: arpa#PRMD$gateway.ADMD$switch.C$ch#RARE Working Group on Mail and Messaging (WG-MSG) [Page 31]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 (You may have noticed correctly that they should have defined such rules in the gateway table, but for the sake of the example, we assume they defined it in mapping table 2. This was the way things were done in the days ofRFC 987, and many networks are still doing it this way these days.) Since a mapping table cannot contain two mapping rules with the same domain on the left hand side, such 'local mappings' are not distributed globally. There exists a RARE draft proposal [13] which defines a mechanism for allowing and automatically dealing with conflicting mapping rules, but this mechanism has not been implemented as to date. After having received the global mapping tables from the MHS Co-ordination Service, many networks add 'local' rules to map2 and the gateway table before installing them on their gateways. Note that the reverse mapping 2 rules for such local mappings _are_ globally unique, and can thus be distributed world- wide. This is even necessary, because addresses that were mapped with a local mapping rule may leak out to other networks (here comes the third party problem again...). Such other networks should at least be given the possibility to map the addresses back. So the global mapping table 1 would in this case contain the two rules: PRMD$gateway.ADMD$tlec.C$nl#arpa# PRMD$gateway.ADMD$switch.C$ch#arpa# Note that if such rules would have been defined as local gate table entries instead of map2 entries, there would have been no need to distribute the reverse mappings world-wide (the reverse mapping of a DDA encodedRFC 822 address is simply done by stripping the SAs, see 3.3.1.1.).3.6. Product specific formats Not all software uses theRFC 1327 format of the mapping tables internally. Almost all formats allow comments on a line starting with a # sign. Some examples of different formats:RARE Working Group on Mail and Messaging (WG-MSG) [Page 32]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993RFC 1327 # This is pureRFC 1327 format # table 1: X.400 ->RFC 822 # PRMD$tlec.ADMD$ade.C$nl#tlec.nl# # etc. # table 2:RFC 822 -> X.400 # arcom.ch#ADMD$arcom.C$ch# # etc. EAN # This is EAN format # It uses the readable format for X.400 domains and TABs # to make a 'readable mapping table format'. # table 1: X.400 ->RFC 822 # P=tlec; A=ade; C=nl; # tlec.nl # etc. # table 2:RFC 822 -> X.400 # arcom.ch # A=arcom; C=ch; # etc. PP # This is PP format # table 1: X.400 ->RFC 822 # PRMD$tlec.ADMD$ade.C$nl:tlec.nl # etc. # table 2:RFC 822 -> X.400 # arcom.ch:ADMD$arcom.C$ch # etc. Most R&D networks have tools to automatically generate these formats from the originalRFC 1327 tables;, some even distribute the tables within their networks in several formats. If you need mapping tables in a specific format, please contact your national or R&D network's gateway manager. See chapter 3.4.RARE Working Group on Mail and Messaging (WG-MSG) [Page 33]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 19933.7. Guidelines for mapping rule definition Beware that defining mapping rules without knowing what you are doing can be disastrous not only for your network, but also for others. You should be rather safe if you follow at least these rules: - First of all, read this tutorial;. - Avoid local mappings; prefer gate table entries. (See chapter 3.5) - Make sure any domain you map to can also be mapped back;. - Aim for symmetry. - Don't define a gateway table entry if the same domain already has a map2 entry. Such a rule would be redundant. - Map to "ADMD=0;" if you will not be connected to any ADMD for the time being. - Only map to "ADMD= ;" if you are indeed reachable through _any_ ADMD in your country. - Mind the difference between "PRMD=;" and "PRMD=@;" and make sure which one you need. (Try to avoid empty or unused attributes in the O/R address hierarchy from the beginning!) - Don't define mappings for domains over which you have no naming authority. - Before defining a mapping rule, make sure you have the permission from the naming authority of the domain you want to map to. Normally, this should be the same organisation as the mapping authority of the domain in the left hand side of the mapping rule. This principle is called 'administrative equivalence'. - Avoid redundant mappings. E.g., if all domains under 'tlec.nl' are in your control, don't define: first.tlec.nl#O$first.PRMD$tlec.ADMD$ade.C$nl# last.tlec.nl#O$last.PRMD$tlec.ADMD$ade.C$nl# always.tlec.nl#O$always.PRMD$tlec.ADMD$ade.C$nl# but rather have only one mapping rule: tlec.nl#PRMD$tlec.ADMD$ade.C$nl#RARE Working Group on Mail and Messaging (WG-MSG) [Page 34]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 - Before introducing a new mapped version of a domain, make sure the world can route to that mapped domain;. E.g., If you are operating a PRMD: C=zz; ADMD=ade; PRMD=ergo; and you want to define the mapping rules: map1: PRMD$ergo.ADMD$ade.C$zz#ergo.zz# map2: ergo.zz#PRMD$ergo.ADMD$ade.C$zz# Make sure that ergo.zz (or at least all of its subdomains) is DNS routeable (register an MX or A record) and will be routed to a gateway that agreed to route the messages from the Internet to you over X.400. In the other direction, if you are operating the Internet domain cs.woodstock.edu, and you want to define a mapping for that domain: map2: cs.woodstock.edu#O$cs.PRMD$woodstock.ADMD$ .C$us# map1: O$cs.PRMD$woodstock.ADMD$ .C$us#cs.woodstock.edu# Make sure that C=us; ADMD= ; PRMD=woodstock; O=cs; (or at least all of its subdomains) is routeable in the X.400 world, and will be routed to a gateway that agreed to route the messages from X.400 to yourRFC 822 domain over SMTP. Within the GO-MHS community, this would be done by registering a line in a so-called domain document, which will state to which mail relay this domain should be routed. Co-ordinate any such actions with your national or MHS' gateway manager. See chapter 3.4.4. Conclusion Mail gatewaying remains a complicated subject. If after reading this tutorial, you feel you understand the basics, try solving some real- life problems. This is indeed a very rewarding area to work in: even after having worked with it for many years, you can make amazing discoveries every other week........RARE Working Group on Mail and Messaging (WG-MSG) [Page 35]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993Appendix A. References [1] Postel, J., "Simple Mail Transfer Protocol", STD 10,RFC 821, USC/Information Sciences Institute, August 1982. [2] Crocker, D., "Standard for the Format of ARPA Internet Text Messages", STD 11,RFC 822, University of Delaware, August 1982. [3] Mockapetris, P., "Domain Names - Concepts and Facilities", and "Domain Names - Implementation and Specification", STD 13, RFCs 1034 and 1035, USC/Information Sciences Institute, November 1987. [4] Kille, S., "Mapping Between X.400 andRFC 822",RFC 987, UK Academic Community Report (MG.19), UCL, June 1986. [5] Braden, R., Editor, "Requirements for Internet Hosts -- Application and Support", STD 3,RFC 1123, USC/Information Sciences Institute, October 1989. [6] Postel, J., Editor, "Internet Official Protocol Standards", STD 1,RFC 1500, USC/Information Sciences Institute, August 1993. [7] Chapin, L., Chair, "The Internet Standards Process",RFC 1310, Internet Activities Board, March 1992. [8] Kille, S., "Mapping between X.400(1988) / ISO 10021 andRFC822",RFC 1327 / RARE RTR 2, University College London, May 1992. [9] Kille, S., "X.400 1988 to 1984 downgrading",RFC 1328 / RARE RTR 3, University College London, May 1992. [10] Plattner, B., and H. Lubich, "Electronic Mail Systems and Protocols Overview and Case Study", Proceedings of the IFIP WG 6.5 International working conference on message handling systems and distributed applications; Costa Mesa 1988; North-Holland, 1989. [11] Houttuin, J., "@route:100%name@address, a practical guide to MHS configuration", Top-Level EC, 1993, (not yet published). [12] Alvestrand, H., "Frequently asked questions on X.400", regularly posted on USEnet in newsgroup comp.protocols.iso.x400. [13] Houttuin, J., Hansen, K., and S. Aumont, "RFC 1327 Address Mapping Authorities", RARE WG-MSG Working Draft, Work in Progress, May 1993.RARE Working Group on Mail and Messaging (WG-MSG) [Page 36]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 [14] "COSINE MHS Pocket User Guide", COSINE MHS Project Team 1992. Also available in several languages from the MHS Co-ordination Server:/user-guides. SeeAppendix D. [15] Grimm, R., and S. Haug, "A Minimum Profile forRFC 987", GMD, November 1987; RARE MHS Project Team; July 1990. Also available from the MHS Co-ordination Server:/procedures/min-rfc987- profile. SeeAppendix D. [16] CCITT Recommendations X.400 - X.430. Data Communication Networks: Message Handling Systems. CCITT Red Book, Vol. VIII - Fasc. VIII.7, Malaga-Torremolinos 1984. [17] CCITT Recommendations X.400 - X.420. Data Communication Networks: Message Handling Systems. CCITT Blue Book, Vol. VIII - Fasc. VIII.7, Melbourne 1988.Appendix B. Index <<Only available in the Postscript version>>Appendix C. Abbreviations ADMD Administration Management Domain ARPA Advanced Research Projects Agency ASCII American Standard Code for Information Exchange ASN.1 Abstract Syntax Notation One BCD Binary-Coded Decimal BITNET Because It's Time NETwork CCITT Comite Consultatif International de Telegraphique et Telephonique COSINE Co-operation for OSI networking in Europe DFN Deutsches Forschungsnetz DL Distribution List DNS Domain Name System DoD Department of Defense EBCDIC Extended BCD Interchange Code IAB Internet Architecture Board IEC International Electrotechnical Commission IESG Internet Engineering Steering Group IETF Internet Engineering Task Force IP Internet Protocol IPM Inter-Personal Message IPMS Inter-Personal Messaging Service IPN Inter-Personal Notification ISO International Organisation for Standardisation ISOC Internet SocietyRARE Working Group on Mail and Messaging (WG-MSG) [Page 37]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 ISODE ISO Development Environment JNT Joint Network Team (UK) JTC Joint Technical Committee (ISO/IEC) MHS Message Handling System MOTIS Message-Oriented Text Interchange Systems MTA Message Transfer Agent MTL Message Transfer Layer MTS Message Transfer System MX Mail eXchanger OSI Open Systems Interconnection OU(s) Organizational Unit(s) PP Mail gatewaying software (not an abbreviation) PRMD Private Management Domain RARE Reseaux Associes pour la Recherche Europeenne RFC Request for comments RTC RARE Technical Committee RTR RARE Technical Report SMTP simple mail transfer protocol STD Internet Standard TCP Transmission Control Protocol UUCP Unix to Unix CoPyAppendix D. How to access the MHS Co-ordination Server Here is an at-a-glance sheet on the access possibilities of the MHS Co-ordination server: E-mail address:RFC822: mhs-server@nic.switch.ch X.400: S=mhs-server; OU1=nic; O=switch; P=switch; A=arcom; C=CH body help # you receive this document index ['directory'] # you receive a directory listing send 'directory''filename' # you receive the specified file FTP address: Internet: nic.switch.ch account: cosine password: 'your email address'RARE Working Group on Mail and Messaging (WG-MSG) [Page 38]
RFC 1506 X.400-Internet Mail Gatewaying Tutorial August 1993 Interactive address: Internet: nic.switch.ch address: PSPDN: +22847971014540 address: EMPB/IXI: 20432840100540 account: info directory: e-mail/COSINE-MHS/ FTAM address: Internet: nic.switch.ch address: PSPDN : +22847971014540 address: EMPB/IXI: 20432840100540 address: ISO CLNS: NSAP=39756f11112222223333aa0004000ae100, TSEL=0103Hex account: ANON gopher address: Internet: nic.switch.chSecurity Considerations Security issues are not discussed in this memo.Author's Address Jeroen Houttuin RARE Secretariat Singel 466-468 NL-1017 AW Amsterdam Europe Tel. +31 20 6391131 Fax. +31 20 6393289RFC 822: houttuin@rare.nl X.400: C=nl;ADMD=400net;PRMD=surf;O=rare;S=houttuinRARE Working Group on Mail and Messaging (WG-MSG) [Page 39]
[8]ページ先頭