Movatterモバイル変換
[0]ホーム
[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]
Obsoleted by:3401,3402,3403,3404 PROPOSED STANDARD
Network Working Group M. MeallingRequest for Comments: 2915 Network Solutions, Inc.Updates:2168 R. DanielCategory: Standards Track DATAFUSION, Inc. September 2000The Naming Authority Pointer (NAPTR) DNS Resource RecordStatus of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.Copyright Notice Copyright (C) The Internet Society (2000). All Rights Reserved.Abstract This document describes a Domain Name System (DNS) resource record which specifies a regular expression based rewrite rule that, when applied to an existing string, will produce a new domain label or Uniform Resource Identifier (URI). Depending on the value of the flags field of the resource record, the resulting domain label or URI may be used in subsequent queries for the Naming Authority Pointer (NAPTR) resource records (to delegate the name lookup) or as the output of the entire process for which this system is used (a resolution server for URI resolution, a service URI for ENUM style e.164 number to URI mapping, etc). This allows the DNS to be used to lookup services for a wide variety of resource names (including URIs) which are not in domain name syntax. Reasons for doing this range from URN Resource Discovery Systems to moving out-of-date services to new domains. This document updates the portions ofRFC 2168 specifically dealing with the definition of the NAPTR records and how other, non-URI specific applications, might use NAPTR.Mealling & Daniel Standards Track [Page 1]
RFC 2915 NAPTR DNS RR September 2000Table of Contents1. Introduction . . . . . . . . . . . . . . . . . . . . . . . .22. NAPTR RR Format . . . . . . . . . . . . . . . . . . . . . .33. Substitution Expression Grammar . . . . . . . . . . . . . .74. The Basic NAPTR Algorithm . . . . . . . . . . . . . . . . .85. Concerning How NAPTR Uses SRV Records . . . . . . . . . . .96. Application Specifications . . . . . . . . . . . . . . . . .107. Examples . . . . . . . . . . . . . . . . . . . . . . . . . .107.1 Example 1 . . . . . . . . . . . . . . . . . . . . . . . . .107.2 Example 2 . . . . . . . . . . . . . . . . . . . . . . . . .127.3 Example 3 . . . . . . . . . . . . . . . . . . . . . . . . .138. DNS Packet Format . . . . . . . . . . . . . . . . . . . . .139. Master File Format . . . . . . . . . . . . . . . . . . . . .1410. Advice for DNS Administrators . . . . . . . . . . . . . . .1411. Notes . . . . . . . . . . . . . . . . . . . . . . . . . . .1512. IANA Considerations . . . . . . . . . . . . . . . . . . . .1513. Security Considerations . . . . . . . . . . . . . . . . . .1514. Acknowledgments . . . . . . . . . . . . . . . . . . . . . .16 References . . . . . . . . . . . . . . . . . . . . . . . . .16 Authors' Addresses . . . . . . . . . . . . . . . . . . . . .17 Full Copyright Statement . . . . . . . . . . . . . . . . . .181. Introduction This RR was originally produced by the URN Working Group [3] as a way to encode rule-sets in DNS so that the delegated sections of a URI could be decomposed in such a way that they could be changed and re- delegated over time. The result was a Resource Record that included a regular expression that would be used by a client program to rewrite a string into a domain name. Regular expressions were chosen for their compactness to expressivity ratio allowing for a great deal of information to be encoded in a rather small DNS packet. The function of rewriting a string according to the rules in a record has usefulness in several different applications. This document defines the basic assumptions to which all of those applications must adhere to. It does not define the reasons the rewrite is used, what the expected outcomes are, or what they are used for. Those are specified by applications that define how they use the NAPTR record and algorithms within their contexts. Flags and other fields are also specified in the RR to control the rewrite procedure in various ways or to provide information on how to communicate with the host at the domain name that was the result of the rewrite.Mealling & Daniel Standards Track [Page 2]
RFC 2915 NAPTR DNS RR September 2000 The final result is a RR that has several fields that interact in a non-trivial but implementable way. This document specifies those fields and their values. This document does not define applications that utilizes this rewrite functionality. Instead it specifies just the mechanics of how it is done. Why its done, what the rules concerning the inputs, and the types of rules used are reserved for other documents that fully specify a particular application. This separation is due to several different applications all wanting to take advantage of the rewrite rule lookup process. Each one has vastly different reasons for why and how it uses the service, thus requiring that the definition of the service be generic. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described inRFC 2119. All references to Uniform Resource Identifiers in this document adhere to the 'absoluteURI' production of the "Collected ABNF" found inRFC 2396 [9]. Specifically, the semantics of URI References do not apply since the concept of a Base makes no sense here.2. NAPTR RR Format The format of the NAPTR RR is given below. The DNS type code [1] for NAPTR is 35. Domain TTL Class Type Order Preference Flags Service Regexp Replacement Domain The domain name to which this resource record refers. This is the 'key' for this entry in the rule database. This value will either be the first well known key (<something>.uri.arpa for example) or a new key that is the output of a replacement or regexp rewrite. Beyond this, it has the standard DNS requirements [1]. TTL Standard DNS meaning [1]. Class Standard DNS meaning [1]. Type The Type Code [1] for NAPTR is 35.Mealling & Daniel Standards Track [Page 3]
RFC 2915 NAPTR DNS RR September 2000 Order A 16-bit unsigned integer specifying the order in which the NAPTR records MUST be processed to ensure the correct ordering of rules. Low numbers are processed before high numbers, and once a NAPTR is found whose rule "matches" the target, the client MUST NOT consider any NAPTRs with a higher value for order (except as noted below for the Flags field). Preference A 16-bit unsigned integer that specifies the order in which NAPTR records with equal "order" values SHOULD be processed, low numbers being processed before high numbers. This is similar to the preference field in an MX record, and is used so domain administrators can direct clients towards more capable hosts or lighter weight protocols. A client MAY look at records with higher preference values if it has a good reason to do so such as not understanding the preferred protocol or service. The important difference between Order and Preference is that once a match is found the client MUST NOT consider records with a different Order but they MAY process records with the same Order but different Preferences. I.e., Preference is used to give weight to rules that are considered the same from an authority standpoint but not from a simple load balancing standpoint. Flags A <character-string> containing flags to control aspects of the rewriting and interpretation of the fields in the record. Flags are single characters from the set [A-Z0-9]. The case of the alphabetic characters is not significant. At this time only four flags, "S", "A", "U", and "P", are defined. The "S", "A" and "U" flags denote a terminal lookup. This means that this NAPTR record is the last one and that the flag determines what the next stage should be. The "S" flag means that the next lookup should be for SRV records [4]. SeeSection 5 for additional information on how NAPTR uses the SRV record type. "A" means that the next lookup should be for either an A, AAAA, or A6 record. The "U" flag means that the next step is not a DNS lookup but that the output of the Regexp field is an URI that adheres to the 'absoluteURI' production found in the ABNF ofRFC 2396 [9]. Since there may be applications that use NAPTR to also lookup aspects of URIs, implementors should be aware that this may cause loop conditions and should act accordingly.Mealling & Daniel Standards Track [Page 4]
RFC 2915 NAPTR DNS RR September 2000 The "P" flag says that the remainder of the application side algorithm shall be carried out in a Protocol-specific fashion. The new set of rules is identified by the Protocol specified in the Services field. The record that contains the 'P' flag is the last record that is interpreted by the rules specified in this document. The new rules are dependent on the application for which they are being used and the protocol specified. For example, if the application is a URI RDS and the protocol is WIRE then the new set of rules are governed by the algorithms surrounding the WIRE HTTP specification and not this document. The remaining alphabetic flags are reserved for future versions of the NAPTR specification. The numeric flags may be used for local experimentation. The S, A, U and P flags are all mutually exclusive, and resolution libraries MAY signal an error if more than one is given. (Experimental code and code for assisting in the creation of NAPTRs would be more likely to signal such an error than a client such as a browser). It is anticipated that multiple flags will be allowed in the future, so implementers MUST NOT assume that the flags field can only contain 0 or 1 characters. Finally, if a client encounters a record with an unknown flag, it MUST ignore it and move to the next record. This test takes precedence even over the "order" field. Since flags can control the interpretation placed on fields, a novel flag might change the interpretation of the regexp and/or replacement fields such that it is impossible to determine if a record matched a given target. The "S", "A", and "U" flags are called 'terminal' flags since they halt the looping rewrite algorithm. If those flags are not present, clients may assume that another NAPTR RR exists at the domain name produced by the current rewrite rule. Since the "P" flag specifies a new algorithm, it may or may not be 'terminal'. Thus, the client cannot assume that another NAPTR exists since this case is determined elsewhere. DNS servers MAY interpret these flags and values and use that information to include appropriate SRV and A,AAAA, or A6 records in the additional information portion of the DNS packet. Clients are encouraged to check for additional information but are not required to do so. Service Specifies the service(s) available down this rewrite path. It may also specify the particular protocol that is used to talk with a service. A protocol MUST be specified if the flags field states that the NAPTR is terminal. If a protocol is specified, but the flags field does not state that the NAPTR is terminal, the nextMealling & Daniel Standards Track [Page 5]
RFC 2915 NAPTR DNS RR September 2000 lookup MUST be for a NAPTR. The client MAY choose not to perform the next lookup if the protocol is unknown, but that behavior MUST NOT be relied upon. The service field may take any of the values below (using the Augmented BNF ofRFC 2234 [5]): service_field = [ [protocol] *("+" rs)] protocol = ALPHA *31ALPHANUM rs = ALPHA *31ALPHANUM ; The protocol and rs fields are limited to 32 ; characters and must start with an alphabetic. For example, an optional protocol specification followed by 0 or more resolution services. Each resolution service is indicated by an initial '+' character. Note that the empty string is also a valid service field. This will typically be seen at the beginning of a series of rules, when it is impossible to know what services and protocols will be offered by a particular service. The actual format of the service request and response will be determined by the resolution protocol, and is the subject for other documents. Protocols need not offer all services. The labels for service requests shall be formed from the set of characters [A-Z0-9]. The case of the alphabetic characters is not significant. The list of "valid" protocols for any given NAPTR record is any protocol that implements some or all of the services defined for a NAPTR application. Currently, THTTP [6] is the only protocol that is known to make that claim at the time of publication. Any other protocol that is to be used must have documentation specifying: * how it implements the services of the application * how it is to appear in the NAPTR record (i.e., the string id of the protocol) The list of valid Resolution Services is defined by the documents that specify individual NAPTR based applications. It is worth noting that the interpretation of this field is subject to being changed by new flags, and that the current specification is oriented towards telling clients how to talk with a URN resolver.Mealling & Daniel Standards Track [Page 6]
RFC 2915 NAPTR DNS RR September 2000 Regexp A STRING containing a substitution expression that is applied to the original string held by the client in order to construct the next domain name to lookup. The grammar of the substitution expression is given in the next section. The regular expressions MUST NOT be used in a cumulative fashion, that is, they should only be applied to the original string held by the client, never to the domain name produced by a previous NAPTR rewrite. The latter is tempting in some applications but experience has shown such use to be extremely fault sensitive, very error prone, and extremely difficult to debug. Replacement The next NAME to query for NAPTR, SRV, or address records depending on the value of the flags field. This MUST be a fully qualified domain-name. Unless and until permitted by future standards action, name compression is not to be used for this field.3. Substitution Expression Grammar The content of the regexp field is a substitution expression. True sed(1) and Perl style substitution expressions are not appropriate for use in this application for a variety of reasons stemming from internationalization requirements and backref limitations, therefore the contents of the regexp field MUST follow the grammar below:subst_expr = delim-char ere delim-char repl delim-char *flagsdelim-char = "/" / "!" / ... <Any non-digit or non-flag character other than backslash '\'. All occurances of a delim_char in a subst_expr must be the same character.>ere = POSIX Extended Regular Expressionrepl = 1 * ( OCTET / backref )backref = "\" 1POS_DIGITflags = "i"POS_DIGIT = %x31-39 ; 0 is not an allowed backref The definition of a POSIX Extended Regular Expression can be found in [8], section 2.8.4. The result of applying the substitution expression to the original URI MUST result in either a string that obeys the syntax for DNS domain-names [1] or a URI [9] if the Flags field contains a 'u'. Since it is possible for the regexp field to be improperly specified, such that a non-conforming domain-name can be constructed, client software SHOULD verify that the result is a legal DNS domain-name before making queries on it.Mealling & Daniel Standards Track [Page 7]
RFC 2915 NAPTR DNS RR September 2000 Backref expressions in the repl portion of the substitution expression are replaced by the (possibly empty) string of characters enclosed by '(' and ')' in the ERE portion of the substitution expression. N is a single digit from 1 through 9, inclusive. It specifies the N'th backref expression, the one that begins with the N'th '(' and continues to the matching ')'. For example, the ERE (A(B(C)DE)(F)G) has backref expressions: \1 = ABCDEFG \2 = BCDE \3 = C \4 = F \5..\9 = error - no matching subexpression The "i" flag indicates that the ERE matching SHALL be performed in a case-insensitive fashion. Furthermore, any backref replacements MAY be normalized to lower case when the "i" flag is given. The first character in the substitution expression shall be used as the character that delimits the components of the substitution expression. There must be exactly three non-escaped occurrences of the delimiter character in a substitution expression. Since escaped occurrences of the delimiter character will be interpreted as occurrences of that character, digits MUST NOT be used as delimiters. Backrefs would be confused with literal digits were this allowed. Similarly, if flags are specified in the substitution expression, the delimiter character must not also be a flag character.4. The Basic NAPTR Algorithm The behavior and meaning of the flags and services assume an algorithm where the output of one rewrite is a new key that points to another rule. This looping algorithm allows NAPTR records to incrementally specify a complete rule. These incremental rules can be delegated which allows other entities to specify rules so that one entity does not need to understand _all_ rules. The algorithm starts with a string and some known key (domain). NAPTR records for this key are retrieved, those with unknown Flags or inappropriate Services are discarded and the remaining records are sorted by their Order field. Within each value of Order, the records are further sorted by the Preferences field. The records are examined in sorted order until a matching record is found. A record is considered a match iff:Mealling & Daniel Standards Track [Page 8]
RFC 2915 NAPTR DNS RR September 2000 o it has a Replacement field value instead of a Regexp field value. o or the Regexp field matches the string held by the client. The first match MUST be the match that is used. Once a match is found, the Services field is examined for whether or not this rule advances toward the desired result. If so, the rule is applied to the target string. If not, the process halts. The domain that results from the regular expression is then used as the domain of the next loop through the NAPTR algorithm. Note that the same target string is used throughout the algorithm. This looping is extremely important since it is the method by which complex rules are broken down into manageable delegated chunks. The flags fields simply determine at which point the looping should stop (or other specialized behavior). Since flags are valid at any level of the algorithm, the degenerative case is to never loop but to look up the NAPTR and then stop. In many specialized cases this is all that is needed. Implementors should be aware that the degenerative case should not become the common case.5. Concerning How NAPTR Uses SRV Records When the SRV record type was originally specified it assumed that the client did not know the specific domain-name before hand. The client would construct a domain-name more in the form of a question than the usual case of knowing ahead of time that the domain-name should exist. I.e., if the client wants to know if there is a TCP based HTTP server running at a particular domain, the client would construct the domain-name _http._tcp.somedomain.com and ask the DNS if that records exists. The underscores are used to avoid collisions with potentially 'real' domain-names. In the case of NAPTR, the actual domain-name is specified by the various fields in the NAPTR record. In this case the client isn't asking a question but is instead attempting to get at information that it has been told exists in an SRV record at that particular domain-name. While this usage of SRV is slightly different than the SRV authors originally intended it does not break any of the assumptions concerning what SRV contains. Also, since the NAPTR explicitly spells out the domain-name for which an SRV exists, that domain-name MUST be used in SRV queries with NO transformations. Any given NAPTR record may result in a domain-name to be used for SRV queries that may or may not contain the SRV standardized underscoreMealling & Daniel Standards Track [Page 9]
RFC 2915 NAPTR DNS RR September 2000 characters. NAPTR applications that make use of SRV MUST NOT attempt to understand these domains or use them according to how the SRV specification structures its query domains.6. Application Specifications It should be noted that the NAPTR algorithm is the basic assumption about how NAPTR works. The reasons for the rewrite and the expected output and its use are specified by documents that define what applications the NAPTR record and algorithm are used for. Any document that defines such an application must define the following: o The first known domain-name or how to build it o The valid Services and Protocols o What the expected use is for the output of the last rewrite o The validity and/or behavior of any 'P' flag protocols. o The general semantics surrounding why and how NAPTR and its algorithm are being used.7. Examples NOTE: These are examples only. They are taken from ongoing work and may not represent the end result of that work. They are here for pedagogical reasons only.7.1 Example 1 NAPTR was originally specified for use with the a Uniform Resource Name Resolver Discovery System. This example details how a particular URN would use the NAPTR record to find a resolver service. Consider a URN namespace based on MIME Content-Ids. The URN might look like this: urn:cid:39CB83F7.A8450130@fake.gatech.edu (Note that this example is chosen for pedagogical purposes, and does not conform to the CID URL scheme.) The first step in the resolution process is to find out about the CID namespace. The namespace identifier [3], 'cid', is extracted from the URN, prepended to urn.arpa. 'cid.urn.arpa' then becomes the first 'known' key in the NAPTR algorithm. The NAPTR records for cid.urn.arpa looked up and return a single record:Mealling & Daniel Standards Track [Page 10]
RFC 2915 NAPTR DNS RR September 2000 cid.urn.arpa. ;; order pref flags service regexp replacement IN NAPTR 100 10 "" "" "/urn:cid:.+@([^\.]+\.)(.*)$/\2/i" . There is only one NAPTR response, so ordering the responses is not a problem. The replacement field is empty, so the pattern provided in the regexp field is used. We apply that regexp to the entire URN to see if it matches, which it does. The \2 part of the substitution expression returns the string "gatech.edu". Since the flags field does not contain "s" or "a", the lookup is not terminal and our next probe to DNS is for more NAPTR records where the new domain is ' gatech.edu' and the string is the same string as before. Note that the rule does not extract the full domain name from the CID, instead it assumes the CID comes from a host and extracts its domain. While all hosts, such as mordred, could have their very own NAPTR, maintaining those records for all the machines at a site as large as Georgia Tech would be an intolerable burden. Wildcards are not appropriate here since they only return results when there is no exactly matching names already in the system. The record returned from the query on "gatech.edu" might look like:;; order pref flags service regexp replacement IN NAPTR 100 50 "s" "z3950+I2L+I2C" "" _z3950._tcp.gatech.edu. IN NAPTR 100 50 "s" "rcds+I2C" "" _rcds._udp.gatech.edu. IN NAPTR 100 50 "s" "http+I2L+I2C+I2R" "" _http._tcp.gatech.edu. Continuing with the example, note that the values of the order and preference fields are equal in all records, so the client is free to pick any record. The flags field tells us that these are the last NAPTR patterns we should see, and after the rewrite (a simple replacement in this case) we should look up SRV records to get information on the hosts that can provide the necessary service. Assuming we prefer the Z39.50 protocol, our lookup might return: ;; Pref Weight Port Target _z3950._tcp.gatech.edu. IN SRV 0 0 1000 z3950.gatech.edu. IN SRV 0 0 1000 z3950.cc.gatech.edu. IN SRV 0 0 1000 z3950.uga.edu. telling us three hosts that could actually do the resolution, and giving us the port we should use to talk to their Z39.50 server. Recall that the regular expression used \2 to extract a domain name from the CID, and \. for matching the literal '.' characters separating the domain name components. Since '\' is the escapeMealling & Daniel Standards Track [Page 11]
RFC 2915 NAPTR DNS RR September 2000 character, literal occurances of a backslash must be escaped by another backslash. For the case of the cid.urn.arpa record above, the regular expression entered into the master file should be "/urn:cid:.+@([^\\.]+\\.)(.*)$/\\2/i". When the client code actually receives the record, the pattern will have been converted to "/urn:cid:.+@([^\.]+\.)(.*)$/\2/i".7.2 Example 2 Even if URN systems were in place now, there would still be a tremendous number of URLs. It should be possible to develop a URN resolution system that can also provide location independence for those URLs. This is related to the requirement that URNs be able to grandfather in names from other naming systems, such as ISO Formal Public Identifiers, Library of Congress Call Numbers, ISBNs, ISSNs, etc. The NAPTR RR could also be used for URLs that have already been assigned. Assume we have the URL for a very popular piece of software that the publisher wishes to mirror at multiple sites around the world: Using the rules specified for this application we extract the prefix, "http", and lookup NAPTR records for http.uri.arpa. This might return a record of the form http.uri.arpa. IN NAPTR ;; order pref flags service regexp replacement 100 90 "" "" "!http://([^/:]+)!\1!i" . This expression returns everything after the first double slash and before the next slash or colon. (We use the '!' character to delimit the parts of the substitution expression. Otherwise we would have to use backslashes to escape the forward slashes and would have a regexp in the zone file that looked like "/http:\\/\\/([^\\/:]+)/\\1/i".). Applying this pattern to the URL extracts "www.foo.com". Looking up NAPTR records for that might return: www.foo.com. ;; order pref flags service regexp replacement IN NAPTR 100 100 "s" "http+I2R" "" _http._tcp.foo.com. IN NAPTR 100 100 "s" "ftp+I2R" "" _ftp._tcp.foo.com. Looking up SRV records for http.tcp.foo.com would return information on the hosts that foo.com has designated to be its mirror sites. The client can then pick one for the user.Mealling & Daniel Standards Track [Page 12]
RFC 2915 NAPTR DNS RR September 20007.3 Example 3 A non-URI example is the ENUM application which uses a NAPTR record to map an e.164 telephone number to a URI. In order to convert the phone number to a domain name for the first iteration all characters other than digits are removed from the the telephone number, the entire number is inverted, periods are put between each digit and the string ".e164.arpa" is put on the left-hand side. For example, the E.164 phone number "+1-770-555-1212" converted to a domain-name it would be "2.1.2.1.5.5.5.0.7.7.1.e164.arpa." For this example telephone number we might get back the following NAPTR records:$ORIGIN 2.1.2.1.5.5.5.0.7.7.1.e164.arpa. IN NAPTR 100 10 "u" "sip+E2U" "!^.*$!sip:information@tele2.se!" . IN NAPTR 102 10 "u" "mailto+E2U" "!^.*$!mailto:information@tele2.se!" . This application uses the same 'u' flag as the URI Resolution application. This flag states that the Rule is terminal and that the output is a URI which contains the information needed to contact that telephone service. ENUM also uses the same format for its Service field except that it defines the 'E2U' service instead of the 'I2*' services that URI resolution uses. The example above states that the available protocols used to access that telephone's service are either the Session Initiation Protocol or SMTP mail.8. DNS Packet Format The packet format for the NAPTR record is: 1 1 1 1 1 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | ORDER | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | PREFERENCE | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ / FLAGS / +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ / SERVICES / +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ / REGEXP / +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ / REPLACEMENT / / / +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+Mealling & Daniel Standards Track [Page 13]
RFC 2915 NAPTR DNS RR September 2000 where: FLAGS A <character-string> which contains various flags. SERVICES A <character-string> which contains protocol and service identifiers. REGEXP A <character-string> which contains a regular expression. REPLACEMENT A <domain-name> which specifies the new value in the case where the regular expression is a simple replacement operation. <character-string> and <domain-name> as used here are defined inRFC1035 [1].9. Master File Format The master file format follows the standard rules inRFC-1035 [1]. Order and preference, being 16-bit unsigned integers, shall be an integer between 0 and 65535. The Flags and Services and Regexp fields are all quoted <character-string>s. Since the Regexp field can contain numerous backslashes and thus should be treated with care. SeeSection 10 for how to correctly enter and escape the regular expression.10. Advice for DNS Administrators Beware of regular expressions. Not only are they difficult to get correct on their own, but there is the previously mentioned interaction with DNS. Any backslashes in a regexp must be entered twice in a zone file in order to appear once in a query response. More seriously, the need for double backslashes has probably not been tested by all implementors of DNS servers. The "a" flag allows the next lookup to be for address records (A, AAAA, A6) rather than SRV records. Since there is no place for a port specification in the NAPTR record, when the "A" flag is used the specified protocol must be running on its default port. The URN Syntax draft defines a canonical form for each URN, which requires %encoding characters outside a limited repertoire. The regular expressions MUST be written to operate on that canonical form. Since international character sets will end up with extensive use of %encoded characters, regular expressions operating on them will be essentially impossible to read or write by hand.Mealling & Daniel Standards Track [Page 14]
RFC 2915 NAPTR DNS RR September 200011. Notes o A client MUST process multiple NAPTR records in the order specified by the "order" field, it MUST NOT simply use the first record that provides a known protocol and service combination. o When multiple RRs have the same "order" and all other criteria being equal, the client should use the value of the preference field to select the next NAPTR to consider. However, because it will often be the case where preferred protocols or services exist, clients may use this additional criteria to sort the records. o If the lookup after a rewrite fails, clients are strongly encouraged to report a failure, rather than backing up to pursue other rewrite paths. o Note that SRV RRs impose additional requirements on clients.12. IANA Considerations The only registration function that impacts the IANA is for the values that are standardized for the Services and Flags fields. To extend the valid values of the Flags field beyond what is specified in this document requires a published specification that is approved by the IESG. The values for the Services field will be determined by the application that makes use of the NAPTR record. Those values must be specified in a published specification and approved by the IESG.13. Security Considerations The interactions with DNSSEC are currently being studied. It is expected that NAPTR records will be signed with SIG records once the DNSSEC work is deployed. The rewrite rules make identifiers from other namespaces subject to the same attacks as normal domain names. Since they have not been easily resolvable before, this may or may not be considered a problem. Regular expressions should be checked for sanity, not blindly passed to something like PERL. This document has discussed a way of locating a service, but has not discussed any detail of how the communication with that service takes place. There are significant security considerations attached to theMealling & Daniel Standards Track [Page 15]
RFC 2915 NAPTR DNS RR September 2000 communication with a service. Those considerations are outside the scope of this document, and must be addressed by the specifications for particular communication protocols.14. Acknowledgments The editors would like to thank Keith Moore for all his consultations during the development of this memo. We would also like to thank Paul Vixie for his assistance in debugging our implementation, and his answers on our questions. Finally, we would like to acknowledge our enormous intellectual debt to the participants in the Knoxville series of meetings, as well as to the participants in the URI and URN working groups.References [1] Mockapetris, P., "Domain names - implementation and specification", STD 13,RFC 1035, November 1987. [2] Mockapetris, P., "Domain names - concepts and facilities", STD 13,RFC 1034, November 1987. [3] Moats, R., "URN Syntax",RFC 2141, May 1997. [4] Gulbrandsen, A., Vixie, P. and L. Esibov, "A DNS RR for specifying the location of services (DNS SRV)",RFC 2782, February 2000. [5] Crocker, D., "Augmented BNF for Syntax Specifications: ABNF",RFC 2234, November 1997. [6] Daniel, R., "A Trivial Convention for using HTTP in URN Resolution",RFC 2169, June 1997. [7] Daniel, R. and M. Mealling, "Resolution of Uniform Resource Identifiers using the Domain Name System",RFC 2168, June 1997. [8] IEEE, "IEEE Standard for Information Technology - Portable Operating System Interface (POSIX) - Part 2: Shell and Utilities (Vol. 1)", IEEE Std 1003.2-1992, January 1993. [9] Berners-Lee, T., Fielding, R.T. and L. Masinter, "Uniform Resource Identifiers (URI): Generic Syntax",RFC 2396, August 1998.Mealling & Daniel Standards Track [Page 16]
RFC 2915 NAPTR DNS RR September 2000Authors' Addresses Michael Mealling Network Solutions, Inc. 505 Huntmar Park Drive Herndon, VA 22070 US Phone: +1 770 921 2251 EMail: michaelm@netsol.com URI:http://www.netsol.com Ron Daniel DATAFUSION, Inc. 139 Townsend Street, Ste. 100 San Francisco, CA 94107 US Phone: +1 415 222 0100 EMail: rdaniel@datafusion.net URI:http://www.datafusion.netMealling & Daniel Standards Track [Page 17]
RFC 2915 NAPTR DNS RR September 2000Full Copyright Statement Copyright (C) The Internet Society (2000). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society.Mealling & Daniel Standards Track [Page 18]
[8]ページ先頭