Adafruit boards that use ATSAMD21 ("M0") or ATSAMD51 ("M4") chips are easy to get working with the Arduino IDE. Most libraries (including the popular ones like NeoPixels and display) will work with those boards, especially devices & sensors that use I2C or SPI.

Now that you have added the appropriate URLs to the Arduino IDE preferences in the previous page, you can open theBoards Manager by navigating to theTools->Board menu.

Once the Board Manager opens, click on the category drop down menu on the top left hand side of the window and selectAll. You will then be able to select and install the boards supplied by the URLs added to the preferences.

Install SAMD Support

First up, install the latestArduino SAMD Boards (version1.6.11 or later)

You can typeArduino SAMD in the top search bar, then when you see the entry, clickInstall

Install Adafruit SAMD

Next you can install the Adafruit SAMD package to add the board file definitions

Make sure you haveType All selected to the left of theFilter your search... box

You can typeAdafruit SAMD in the top search bar, then when you see the entry, clickInstall

Quit and reopen the Arduino IDE to ensure that all of the boards are properly installed. You should now be able to select and upload to the new boards listed in theTools->Board menu.

Select the matching board, the current options are:

• Feather M0 (for use with any Feather M0 other than the Express)
• Feather M0 Express
• Metro M0 Express
• Circuit Playground Express
  
• Gemma M0
• Trinket M0
  
• QT Py M0
  
• ItsyBitsy M0
• Hallowing M0
• Crickit M0(this is for direct programming of the Crickit, which is probably not what you want! For advanced hacking only)
• Metro M4 Express
• Grand Central M4 Express
• ItsyBitsy M4 Express
• Feather M4 Express
• Trellis M4 Express
• PyPortal M4
• PyPortal M4 Titano
• PyBadge M4 Express
• Metro M4 Airlift Lite
• PyGamer M4 Express
• MONSTER M4SK
• Hallowing M4
• MatrixPortal M4
• BLM Badge

Windows 7 and 8.1

Blink

Now you can upload your first blink sketch!

Plug in the SAMD21 M0 or SAMD51 M4 board, and wait for it to be recognized by the OS (just takes a few seconds). It will create a serial/COM port, you can now select it from the drop-down, it'll even be 'indicated' as Trinket/Gemma/Metro/Feather/ItsyBitsy/QT Py/Trellis or whatever the board is named!

Now load up the Blink example

// the setup function runs once when you press reset or power the boardvoid setup() {  // initialize digital pin 13 as an output.  pinMode(13, OUTPUT);}// the loop function runs over and over again forevervoid loop() {  digitalWrite(13, HIGH);   // turn the LED on (HIGH is the voltage level)  delay(1000);              // wait for a second  digitalWrite(13, LOW);    // turn the LED off by making the voltage LOW  delay(1000);              // wait for a second}

// the setup function runs once when you press reset or power the boardvoid setup() {  // initialize digital pin 13 as an output.  pinMode(13, OUTPUT);}// the loop function runs over and over again forevervoid loop() {  digitalWrite(13, HIGH);   // turn the LED on (HIGH is the voltage level)  delay(1000);              // wait for a second  digitalWrite(13, LOW);    // turn the LED off by making the voltage LOW  delay(1000);              // wait for a second}

And click upload! That's it, you will be able to see the LED blink rate change as you adapt thedelay() calls.

Successful Upload

If you have a successful upload, you'll get a bunch of red text that tells you that the device was found and it was programmed, verified & reset

After uploading, you may see a message saying "Disk Not Ejected Properly" about the ...BOOT drive. You can ignore that message: it's an artifact of how the bootloader and uploading work.

Compilation Issues

If you get an alert that looks like

Cannot run program "{runtime.tools.arm-none-eabi-gcc.path}\bin\arm-non-eabi-g++"

Make sure you have installed theArduino SAMD boards package, you needbothArduino & Adafruit SAMD board packages

Manually bootloading

If you ever get in a 'weird' spot with the bootloader, or you have uploaded code that crashes and doesn't auto-reboot into the bootloader, click theRST buttontwice (like a double-click)to get back into the bootloader.

The red LED will pulse and/or RGB LED will be green, so you know that its in bootloader mode.

Once it is in bootloader mode, you can select the newly created COM/Serial port and re-try uploading.

You may need to go back and reselect the 'normal' USB serial port next time you want to use the normal upload.

Ubuntu & Linux Issue Fix

 Follow the steps for installing Adafruit's udev rules on this page.