Sketches of & Index to Names to Window Parts

Below our sketch names all of the parts of a double hung window assembly, viewed from outside and from one side.

Below: a detailed view of how a typical window sash is assembled.

Our sketches of basic double-hung window parts (above and below) appeared inBasic Housing Inspection and later in other window guides in the U.S. in the 1940s or earlier.

Our sketch of repair of window sash cords and weights shows how older double-hung windows operated with sash weights and came from the same source.

Definition & illustration of Awning Type Windows

Awning-type windows (photo at left) operate by a crank and open outwards from the bottom, hinged at the sash top.

Awning windows that open out from the bottom, as most do, can be left open in light rain with less chance of water entering through the window opening itself, allowing ventilation in rainy weather.

As we illustrate and expand atWINDOW TYPES, a PHOTO GUIDE, depending on their pivot or axis point and opening direction, awning type windows may be defined more narrowly as austral windows, pivot windows, and projecting windows as well as identified as top opening (hinged at bottom, rain comes in when open) or bottom opening (hinged at top).

Above we show a sliding pivot type awning window opens at both top and bottom. This window is in a rental apartment in Buenos Aires, Argentina.

Definition & illustration of Basement Windows & Window Wells

Basement windows vary among many of the styles listed here, but because they are normally close to or even below ground level, special installation detail and attention to handling of roof spillage are critical to avoid leaks, rot, and indoor water and mold problems.

The photo above shows a basement window that needs a window-well to avoid water damage, rot, insect attack at this opening.

SeeWINDOW LEAKS INTO BASEMENT.

Definition & illustration of Bay Windows

Bay windows project out from the building wall and may incorporate both fixed vertical glazing and operable sashes of any type, usually double-hung or casement style.

As you will observe in these window type photos, a bay window is angled (an angled-bay window) using angled sides and a flat main center section in construction.

As we explain below, a rounded window of this type should be called a bow window, not a bay. (Unless it's my stomach)

If the roof over a bay window is not maintained, or if the window is not properly installed,

LEAKS & CONDENSATION [image] are likely.

This BAY WINDOW [image] uses fixed center glass and double hung sashes at either side.

Don't confuse a bay window (including a flat central segment) and a bow or curved window.

Definition & illustration of Bow Windows compared with oriel windows

Bow windows project out from the building wall and may incorporate both fixed vertical glazing and operable sashes of any type, though in the curved frame of a bow window the sash may also be specially constructed and glazed to follow that arc, or the operable units in the bow window may simply be small individual panes that operate as sliders or awnings.

In this photo of a bow window, shown on a home in Boston, MA, is constructed with the bow extending to floor level.

And at the right of the bow window is a smaller oriel window, also a bow but whose window opening does not extend to floor level.

Like a bay window, If the roof over a boy window is not maintained, or if the window is not properly installed, leaks and condensation are likely.

Definition & illustration of Casement windows

Casement-type windows are hinged and like awning windows, casements also operate by a crank.

But casement windows but are hinged at oneside and open outwards like a door.

Traditional casement windows on most buildings are constructed of steel sashes and frames, but casements are also constructed of wood, vinyl-clad wood, and solid vinyl.

Watch out: steel framed casement windows such as the unit shown above are usually low in energy efficiency, sporting single glazed panes, no thermal break in the steel frame to slow heat loss to the building exterior, leaky, and often rusted or painted stuck as well.

Definition & illustration of Dormer Windows

DORMERS [photo] are not a window-type but rather are an expansion of space under the roof area of a building.

Nearly any dormer type, even thisSLATE ROOF DORMER EXAMPLE [image] of window can be installed in a dormer.

Dormers as a means of gaining space and light to make an attic area into living space have been around for along time [image]

Definition & illustrations of Double-Hung Windows

DOUBLE-HUNG WINDOWS [image] use two moveable sashes, an upper and lower unit that slide past one another.

Above is a single pane type double hung window in a Poughkeepsie NY home built ca 1925. That window used traditional sash weights.

Below is a modern vinyl or plastic double hung window sash whose sashes are supported by springs rather than sash weights.

Watch out: when inspecting a home for window problems don't assume that all new or recently-installed sashes are operable without doing some actual testing. On both sash weight and spring type window sashes may come crashing down if the sash weight rope or spring is broken.

Because those window support components are hidden from normal view, testing the window for proper operation is important.

Definition & Illustrations of Eyebrow Windows

Eyebrow windows may be fixed or operable and are built protruding through the slope of a roof surface.

Our photo above shows a lovely antique eyebrow window on a roof in New York state. Eyebrow windows may also appear as small peaked installations but the classic is rounded such as we show above.

An "eyebrow" window is a miniature dormer in essence but requires less supporting framer than a larger dormer.

An eyebrow window is not a dormer or dormer window (see Dormers, above).

Definition & illustration of Fixed Glass or Fixed Glazing Windows

Fixed glass windows may be vertical or sloped and in many lexicons include fixed skylights.

Our photo (left) illustrates fixed vertical glazing on a diner in Poughkeepsie, New York.

SeeVERTICAL GLAZING DETAILS for an example.

Also seeSITE BUILT DOUBLE GLAZED WINDOWS.

Definition & illustration of Ox Eye Windows

Shown just below, the eye-shaped window in the center of our photo is an ox-eye window in the wall of the Hacienda Tenexac in Tlaxcala, Mexico, constructed ca 1532, shortly after the arrival of Hernán Cortés de Monroy y Pizarro.

Looking more closely at the wall top (click to enlarge this or any image) and you'll also notice musket firing slots built into the parapet.

Definition & illustration of Single hung windows & window sashes

Single-hung windows are similar to double-hung units but only one sash, usually the lower one, is movable.

Definition & illustration of Skylights, roof skylights, fixed or operable

...

...

Skylights shown here are an example of sloped glazing, normally built into a roof surface.

Our skylight photos above show an older style wire-reinforced and vented skylight in a copper roof (above left), and at above right, a series of custom-built copper-clad skylights in a re-roofed section of a similar building, both on the Vassar College Campus in Poughkeepsie, NY.

Skylights may be operable for ventilation or fixed.

SeeSLOPED GLAZING DETAILS and

seeSKYLIGHT LEAK DIAGNOSIS & REPAIR.

Definition & illustration of Slider Windows

Slider type windows use sashes that slide horizontally like "bypass doors", one sash passing the other on the inside or outside.

TheseSLIDER WINDOWS [image] on a log cabin we renovated in Minnesota were site-built, leaky, and replaced entirely.

Below: a badly-fogged slider window in an apartment building - this window has lost its seal and that needs replacement.

Definition & illustrations of Storm Windows

Storm windows are additional windows, fixed or operable, that are hung or installed over the main window sash to reduce heat loss through the window.

A "triple-track" storm window incorporates a movable screen and upper and lower widow sashes.

Each layer of glazing added to a window cuts heat loss through the window glass by about one third, but if the window is drafty any energy savings will be lost until the drafts are found and sealed.

Also seeAIR LEAK MINIMIZATION

andAIR SEALING STRATEGIES

as well asENERGY SAVINGS RETROFIT LEAK SEALING GUIDE

And seeSTORM WINDOW WEEP HOLES - why we need weep holes to avoid sill rot at storm windows

For a table illustrating nearly all window types, names and architectural features, seeWindow Types - Photo Guide

Inspect, diagnose,& repair doors, skylights, sloped glazing, vertical glazing, energy-losing windows, & leaky basement windows

• Halda, Bonnie J., A.I.A.HISTORIC GARAGE & CARRIAGE DOORS: REHABILATION SOLUTIONS [PDF] Preservation Tech Notes, Doors No. 1, U.S. NPS, Technical Preservation Services, retrieved 2022/10/10, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Doors01.pdf
  
  
• Myers, John H.,THE REPAIR OF HISTORIC WOODEN WINDOWS [PDF] (1981) U.S. National Park Servivce, Technical Preservation Services, Preservation Brief No. 9, retrieved 2017/12/07, original source: www.nps.gov/tps/how-to-preserve/briefs/9-wooden-windows.htm
  
  Excerpt:
  
  Technical Preservation Services recommends the retention and repair of original windows whenever possible.
  
  We believe that the repair and weatherization of existing wooden windows is more practical than most people realize, and that many windows are unfortunately replaced because of a lack of awareness of techniques for evaluation, repair, and weatherization.
  
  Wooden windows which are repaired and properly maintained will have greatly extended service lives while contributing to the historic character of the building.
  
  Thus, an important element of a building's significance will have been preserved for the future.
• OHJ, "Fixing Double-hung Windows." Old House Journal (no. 12, 1979): 135.
• Park, Sharon C. AIA,THE REPAIR & THERMAL UPGRADING of HISTORIC STEEL WINDOWS [PDF] Preservation Brief No. 13, US NPS, Technical Preservation Services, U.S. Department of the Interior
  
  Excerpts:
  
  This Brief identifies various types of historic steel windows that dominated the metal window market from 1890-1950. It then gives criteria for evaluating deterioration and for determining appropriate treatment, ranging from routine maintenance and weatherization to extensive repairs, so that replacement may be avoided where possible.
  
  This information applies to do-it-yourself jobs and to large rehabilitations where the volume of work warrants the removal of all window units for complete overhaul by professional contractors.
  
  This Brief is not intended to promote the repair of ferrous metal windows in every case, but rather to insure that preservation is always the first consideration in a rehabilitation project.
  
  Some windows are not important elements in defining a building's historic character; others are highly significant, but so deteriorated that repair is infeasible.
  
  In such cases, the Brief offers guidance in evaluating appropriate replacement windows.
• Phillips, Morgan, and Selwyn, Judith. Epoxies for Wood Repairs in Historic Buildings. Washington, DC: Technical Preservation Services, U.S. Department of the Interior (Government Printing Office, Stock No. 024016000951), 1978.
• US DOEWEATHER RESISTIVE BARRIERS [PDF] U.S. Department of Energy, how to select and install housewrap and other types of weather resistive barriers
• Weeks, Kay D. and David W. Look, Preservation Brief 10:EXTERIOR PAINT PROBLEMS ON HISTORIC WOODWORK [PDF] Preservation Brief No. 10, Washington, DC: Technical Preservation Services, U.S. Department of the Interior, - retrieved 2022/10/02, original source: https://www.nps.gov/tps/how-to-preserve/briefs/10-paint-problems.htm
  
  Excerpts:
  
  A cautionary approach to paint removal is included in the guidelines to the Secretary of the Interior Standards for Rehabilitation.
  
  Removing paints down to bare wood surfaces using harsh methods can permanently damage those surfaces; therefore such methods are not recommended.
  
  Also, total removal obliterates evidence of the historical paints and their sequence and architectural context.
  
  This Brief expands on that advice for the architect, building manager, contractor, or homeowner by identifying and describing common types of paint surface conditions and failures, then recommending appropriate treatments for preparing exterior wood surfaces for repainting to assure the best adhesion and greatest durability of the new paint.
  
  Although the Brief focuses on responsible methods of "paint removal," several paint surface conditions will be described which do not require any paint removal, and still others which can be successfully handled by limited paint removal.
  
  In all cases, the information is intended to address the concerns related to exterior wood.
  
  It will also be generally assumed that, because houses built before 1950 involve one or more layers of lead-based paint, the majority of conditions warranting paint removal will mean dealing with this toxic substance along with the dangers of the paint removal tools and chemical strippers themselves.

Below we show two problem windows at building basements. If your basement windows seem to be points of leakage into the building see the article Window Leaks into Basement - cited just above.

...

...

If your skylights leak or seem plagued with condensation there is a risk of hidden rot or even mold contaminated ceiling or roof insulation.

SeeSLOPED GLAZING DETAILS - proper installation details for sloped windows and skylights and

seeSKYLIGHT LEAK DIAGNOSIS & REPAIR - how to avoid leaks, rot, damage at skylights

If you are building or installing vertical windows such as the fixed glass triangular windows shown in this photograph,

seeVERTICAL GLAZING DETAILS - proper installation details for vertical fixed glass windows to avoid leaks, rot, condensation, heat loss.

...

Doors: door type examples of entrances

Details about doors are found at

• DOORS, EXTERIOR, Selecting & Installing
• DOORS, INTERIOR

Our photo (below) shows a modern solid-woodmulti-lite exterior door [photo] used at an enclosed porch.

Because of weather exposure and rain splash-up from the entry platform, and because there is no protective storm door installed at this entry, the wood door must be kept coated with paint or polyurethane to avoid water damage, swelling, or rot.

...

Our second exterior door photo (above right) shows an expedient, but insecure means of securing antique interior doors made from a converted ( ca 1910) swing-type garage door.

Window & Door Leaks & Damage

For some home buyers, especially of older homes, un-disclosed problems with windows and doors (leaks, rot, energy loss, operability) can be a real "sleeper" that later turns out to be a source of major headaches and big costs.

At a home inspection in New York we found an entire development in which nearly every wooden window in the 1960's - 1970's homes was badly rotted.

The same siding installation company had made the same mistake - hundreds of times. A flashing error at window tops and sides sent wind-blown rain into the window frame, leading to rot and in some cases termite damage as well.

Windows and doors that are leaky or poorly constructed can be a big energy loser on buildings as well. Here we provide a series of articles on the inspection, diagnosis, installation, and repair of problems at windows and doors on residential buildings.

Exterior building doors, with focus on selecting and installing energy-efficient doors are discussed in detail

atWINDOW / DOOR ENERGY EFFICIENT, DOE.

At left ourphoto shows rot and damage that will eventually occur if a sliding glass door threshold is installed without a pan flashing and is left for a decade or more with little attention to maintenance of sealants nor paint coating.

The common pine brick mold wood trim around this door as well as a common pine door threshold were particularly prone to water absorption and rot.

Definition & illustration of Basement Walkout Doors

Basement walkout doors were originally usually site-built using sloped wood (photo, below left); if your basement door is in as terrible shape as the unit shown here.

The worry about leaks into the building basement should take second place to the immediate life-safety hazard of a rotted door like this one.

Modern basement walkout doors are purchased as a pre-fab steel unit from manufacturers such as Bilco™ and may be set on a site-built or pre-fabricated masonry stairwell.

Details are atBASEMENT WALKOUTS & COVERS and

atBASEMENT STAIRS

Definition & illustration of Door & Window Sill Rabbet Cuts & Flashing Details

Our window sill photo (below, courtesy Carson Dunlop Associates ), shows the traditional rabbet cut or slot on the underside of the window sill.

This window sill detail is intended to aid drainage off of the window sill by reducing the tendency of water to follow, by capillary action, the underside of the sill back to drain down the building wall.

FLASHING MEMBRANES PEEL & STICK

andFLASHING WALL DETAILS include details to avoid leaks at building windows

Details are atWINDOW FLASHING & SEALING Guide

Window Repair, Renovation, Restoration & Improvement Guides

• Anderson A-Series CASEMENT WINDOWS & WINDOW PARTS [PDF] - web search 01/15/2010, original source: http://www.andersenwindows.com/homeowner/pdfs/A-Series_Casement.pdf
• Closs, Christopher W.,REPAIRING AND UPGRADING MULTI-LIGHT WOODEN MILL WINDOWS [PDF] (1986) Preservation Tech Notes, U.S. NPS, Windows No. 16, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows16.pdf
• Feist, William C.,REPLACEMENT WOODEN FRAMES & SASH: PROTECTING WOODWORK AGAINST DECAY [PDF] (1984) Windows Preservation Briefs No. 4, National Park Service, U.S. Department of Interior, Preservation - retrieved 2022/10/07,
  Excerpts:
  
  Studies undertaken by the Forest ProductsLaboratory (FPL), U.S. Departmentof Agriculture , have convincingly shownthat when wooden elements in windowsare treated with a water repellent verylittle decay will occur in the new windowseven if many years of maintenanceneglect follow.
  
  This importantfinding was an outgrowth of a researchproject to determine al ternatives topotentially toxic chemical woodpreservatives. ...
  
  A 20-year test on wooden windows bythe FPL in Madison, Wisconsin, hasconcluded that there is a safer alternativeto traditional water-repellent chemicalpreservatives for treating wood inorder to prevent decay.
  
  It was foundthat the easiest way to prevent decay inwoodwork items such as frames andsash is the application of small amountsof wax to the surface.
  
  The wax, in theabsence alchemical preservatives. protectsthe wood from excessive moistureand provides good long-term protectionto window units and other wood exposedabove ground.
• Fisher, Charles E.,ALUMINUM REPLACEMENTS for STEEL INDUSTRIAL SASH [PDF] (1986) Preservation Tech Notes, U.S. NPS, Windows No. 11, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows12.pdf
  
  Excerpt:
  The contractor's survey of thehistoric windows in the spring of 1984revealed that extensive rusting of theframes had occurred and that manywere racked. The severe rusting hadalso contributed to the spalling of sections of the concrete sills, jambs, andspandrels (see figure 2).
  
  Repair andupgrading options to maintain the historic windows were quite limited dueto the size of the glazing bars.
  
  Theshallow depth of the metal glazingbars (muntins) seemingly precludedthe installation of sealed insulatingglass within the existing lites, even ifthe windows could structurally supportthe additional weight.
  
  The only practical way of double-glazing would haveinvolved the use of interior stormswith units that were either operable orwere removable for ease of cleaning.
• Fisher, Charles E.,PLANNING APPROACHES to WINDOW PRESERVATION [PDF] (1984), Windows Preservation Briefs No. 1, National Park Service, U.S. Department of Interior, Preservation - retrieved 2022/10/07,
  Excerpts:
  
  Window Evaluation Criteria In conjunctionwith the HVAC analysis, threewindow alternatives were considered:
  
  • repairing the existing windows andfixing them closed;
  • modifying the existing windows byinstalling insulated glazing for improvedthermal performance; or
  • replacing the existing windows withhigh-quality, aluminum units with insulatingglass that matched the appearanceof the original.
  
  Criteria for evaluating the threealternatives related to aesthetics, windowperformance and economics:
  
  (1) The historic character of thelarge office windows had to be preserved;
  
  (2) Only high quality materials and workmanship would be used in any workon the windows, consistent with thegoal of creating prime office space;
  
  (3) As a result of the decision previouslyreached concerning the newHVAC system for the building, the windowshad to be fixed closed;
  
  (4) While specific requirements werenot established at the outset for theenergy efficiency of the windows, a projectgoal was to have the overall buildingmeet the energy utilization and buildingperformance standards establishedby the American Society of Heating,Refrigerating and Air-ConditioningEngineers,Inc. (ASHRAE); and
  
  (5) Any changes to the windows inorder to improve energy performanceneeded to be cost-effective.
  
  With these criteria established, thethree window treatments were then examinedin detail.
• Fisher, Charles E., INSTALLING INSULATING GLASS in EXISTING STEEL WINDOWS [PDF] (1984) Windows Preservation Briefs No. 2, National Park Service, U.S. Department of Interior, Preservation - retrieved 2022/10/07,
  Excerpt:
  Four possible approaches to the windows wereexamined:
  
  • repair and repaint the existing windows;
  • repair existing windows and installinsulating glass;
  • replace existing windows with custom-made, dou ble-glazed steel sash; or
  
  • remove existing units and installnew aluminum double-hung thermalsash.
• Fisher, Charles E.,INSTALLING INSULATING GLASS in EXISTING WOODEN SASH INCORPORATING the HISTORIC GLASS [PDF] (1985) Preservation Tech Notes, U.S. NPS, Windows No. 11, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows11.pdf
  
  Excerpt:
  The 102 wooden windows on floors3 through 8 were over 100 years oldyet still in good condition, partlybecause their deep setback from theface of the building provided someprotection from the weather.
  
  Therewas considerable air leakage, however, due to lack of weatherstripping,cracked putty seals around the glass,and shrinkage and cracks in the caulkaround the outside frame.
  
  Sincetenants would be responsible for theirheating and cooling bills upon completion of the rehabilitation work,some form of double glazing wasconsidered desirable.
  
  The windows had both squareand arched tops and the size variedconsiderably, making the cost of agood quality aluminum replacementunit quite high.
  
  The 2 1/2" thick windows varied in height from 6 1/2" to9', depending on the floor level, andthe windows on the two-story addition differed in width from thosebelow; overall the windows ranged inwidth from 3 to 4 feet.
• Fisher, Charles E.,INTERIOR STORM WINDOWS: MAGNETIC SEAL [PDF] (1984), Window Preservation Brief No. 9, National Park Service, U.S. Department of Interior, Preservation
• Fisher, Charles E. & Christina Henry,INTERIOR STORMS for STEEL CASEMENT WINDOWS [PDF] (1986) Window Preservation Brief No. 15, National Park Service, U.S. Department of Interior, Preservation - retrieved 2022/10/07, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows15.pdf
• Fisher, Charles E.,REPLACEMENT WOOD SASH using True Divided Lights and an Interior Piggyback Energy Panel [PDF] (2008) Preservation Tech Notes, U.S. NPS, Windows No. 21, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows21.pdf
  
  Piggyback storm window panels on wood sash windows.
  
• Muckenfuss, Laura A., & Charles E. Fisher,INTERIOR METAL STORM WINDOWS [PDF] Window Preservation Brief No. 5, NPS, Op. Cit., - retrieved 2022/10/07,
• Muckenfuss, Laura A. & Charles E. Fisher,WINDOW AWNINGS [PDF] US NPS, Preservation Tech Notes, Windows, No. 7, National Park Service, US Department of Interior, retrieved 2022/10/07, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows07.pdf
• NRFC,SOLAR HEAT GAIN & WINDOWS, the facts about [PDF] NFRC, National Fenestration Rating Council, January 2005, NFRC website: www.nfrc.org retrieved 12/4/2010, original source: http://www.nfrc.org/documents/SolarHeatGain.pdf.
• Park, Sharon C., AIA,THERMAL RETROFIT of HISTORIC WOODEN SASH USING PIGGYBACK STORM PANELS [PDF] (1984), Window Preservation Brief No. 8, NPS, Op. Cit., - retrieved 2022/10/07
• Parrott, Charles,ALUMINUM REPLACEMENT WINDOWS WITH SEALED INSULATING GLASS AND TRAPEZOIDAL MUNTIN GRIDS [PDF] (1985) Preservation Tech Notes, U.S. NPS, Windows No. 13, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows13.pdf
  
  Excerpt:
  The decision was reached toevaluate the cost and appearance of anon-wooden, double glazed, prefinished, single-hung window with applied muntins grids on the exteriorrather than integral muntins.
  
  The objective was to determine whether anon-wooden commercially availablewindow could closely match the configuration and appearance of thehistoric windows.
• Powers, Robert M. [PDF] (1989)REPAIR and RETROFITTING INDUSTRIAL STEEEL WINDOWS [PDF] Preservation Tech Notes, U.S. NPS, Windows No. 17, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows17.pdf
  
  Excerpt:
  Since the Lippincott Building wasused for a long time as a storage facility, the windows had not been painted,oiled, reglazed, or caulked, nor hadmissing or damaged parts been replaced in well over twenty years (seefigure 1).
  
  Naturally, many of the windows exhibited problems typicallyfound on inadequately maintainedsteel windows, including corrosion,bent and bowed metal sections, nonoperable ventilators, missing or nonfunctional hardware and brokenglazing.
  
  Furthermore, some of theoriginal windows had been removedand replaced with double-hung aluminum windows, and other windowopenings had been infilled with glassand concrete block, metal louvered airvents, ductwork and other mechanicalequipment .
• Randl, Chad,ALUMINUM REPLACEMENT WINDOWS for STEEL PROJECTING UNITS with True Divided Lights & Matching Profiles [PDF] Preservation Tech Notes, U.S. NPS, Windows No. 20, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows20.pdf
• Randl, Chad,PRESERVING HISTORIC CORRIDOR DOORS & GLAZING in HIGH-RISE BUILDINGS [PDF] (2001) Preservation Tech Notes, U.S. NPS, Historic Interior Spaces No. 3, retrieved 2022/10/10, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Interior03.pdf
  Excerpt:
  Historic office building corridors areoften rich in distinctive features andmaterials.
  
  Glass door panels with goldleaf lettering, glass transoms and sidelights, woodwork and wainscoting allprovide a physical connection to the waybusiness was conducted in the late 19thcentury.
  
  Moreover, they display a levelof detail, and quality of material andcraftsmanship that are rare in new construction.
  
  Some of the same characteristics that make historic corridors significant and unique, however, may present achallenge to their sensitive rehabilitation.
  
  A primary difficulty lies in bringinghistoric features and materials "up tocode."
• Randl, Chad,REPAIRING STEEL CASEMENT WINDOWS [PDF] (2002) Preservation Tech Notes, U.S. NPS, Windows No. 19, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows19.pdf
  
  Excerpt:
  The windows on 9 Roxbury Roadshowed deterioration and damage typical of historic steel casements. In thecourse of over seventy-fIve years, corrosion, wear and some distortion of thesash and frame had occurred.
  
  Rustwas particularly prevalent along thelower parts of the sash and framewhere water had penetrated the distorted opening and the cracked perimeter caulk (see figure 4).
  
  Originally tightfitting, all of the sash were bent out ofalignment with resulting gaps from1116" inch to 3/4" inch between sashand frame. Hardware was corroded,stiff, and in some windows, seizedshut. Prior attempts to force the distorted windows closed had also bentsome of the locking handles and otherhardware.
  
  Ten windows were completely inoperable either because they were so farout of alignment that they could not beopened and closed or because successive layers of paint had sealed themshut.
  
  When a previous owner installedwindow-mounted air conditioners notdesigned for steel sash, four additionalwindows were modified and madeinoperable.
• Randl, Chad,THE USE of AWNINGS on HISTORIC BUILDINGS: REPAIR, REPLACEMENT & NEW DESIGN [PDF] NPS Preservation Brief No. 44

• Stachelberg, Cas & Chad Randl,REPAIR & REHABILITATION of HISTORIC SIDEWALK VAULT LIGHTS [PDF] (2003) Preservation Tech Notes, U.S. NPS, Historic Glass No. 2, retrieved 2022/10/10, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Glass02.pdf
  
  Broadway vault light project, Excerpts:
  Deteriorated historic sidewalk vault lights should be repaired wherever possible. Missing panels can be replicated with new panels that match closely the detail and overall appearance of the historic vault lights
  
  Beginning in the 1850s, sidewalk vault lights became a common feature amidst the burgeoning manufacturing districts of America's urban streetscapes. These cast-iron panels, fitted with clear glass lenses, were set into the sidewalk in front of building storefronts.
  
  They permitted daylight to reach otherwise dark basements (or "vaults") that extended out beneath the sidewalks, creating more useable or rentable space for building owners.
• Staveteig, Kaaren R.,MAINTENANCE & REPAIR of ALUMINUM WINDOWS [PDF] (2008) Preservation Tech Notes, U.S. NPS, Windows No. 22, retrieved 2022/10/15, original source https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows22.pdf
  
  Excerpt:
  ... aluminum windows in buildings have been around since the 1930sand that numerous landmark buildingsin the J 930s and 1940s prominentlyfeatured them in their design.
  
  AfterWorld War II, aluminum windowsgained more widespread use in the construction industry and soon surpassedsteel window sales.
  
  By the 1970s, theyrivaled the dominant wood windowindustry, particularly in commercialand institutional construction.
  
  Thehistoric significance of early aluminumwindows is now being recognized andefforts are being taken to preserve andrehabilitate them.
• Stumes, Paul P.E., (Parks Canada),REINFORCING DETERIORATED WOODEN WINDOWS [PDF] (1986) Preservation Tech Notes, U.S. NPS, Windows No. 14, retrieved 2022/10/11, original source: https://www.nps.gov/tps/how-to-preserve/tech-notes/Tech-Notes-Windows14.pdf
• Trissler, Wayne & Charles E. Fisher,EXTERIOR STORM WINDOWS: CASEMENT DESIGN WOODEN STORM SASH [PDF] Window Preservation Brief No. 3, NPS, Op. Cit., - retrieved 2022/10/07
• Vogel, Neal A. & Rolf Achilles, ThePRESERVATION & REPAIR of HISTORIC STAINED & LEADED GLASS [WINDOWS] [PDF] (2007), Preservation Brief No. 33, NPS, Op. Cit., - retrieved 2022/10/08, original source: https://www.nps.gov/tps/how-to-preserve/briefs/33-stained-leaded-glass.htm
  Excerpt:
  This Brief gives a short history of stained and leaded glass in America. It also surveys basic preservation and documentation issues facing owners of buildings with leaded glass. It addresses common causes of deterioration and presents repair, restoration, and protection options.