Commit0de9d86

committed

fix lint

1 parent138a7f7 commit0de9d86Copy full SHA for 0de9d86

File tree

1 file changed

+14

-14

lines changed

variants/STM32H7xx/H742Z(G-I)T_H743Z(G-I)T_H747A(G-I)I_H747I(G-I)T_H750ZBT_H753ZIT_H757AII_H757IIT
- variant_NUCLEO_H753ZI.h

1 file changed

+14

-14

lines changed

`‎variants/STM32H7xx/H742Z(G-I)T_H743Z(G-I)T_H747A(G-I)I_H747I(G-I)T_H750ZBT_H753ZIT_H757AII_H757IIT/variant_NUCLEO_H753ZI.h‎`

Lines changed: 14 additions & 14 deletions

Original file line number	Diff line number	Diff line change
`@@ -200,58 +200,58 @@`
`200`	`200`
`201`	`201`	`// On-board LED pin number`
`202`	`202`	`#ifndefLED_BUILTIN`
`203`		`-#defineLED_BUILTIN PB0 // LD1`
	`203`	`+#defineLED_BUILTIN PB0 // LD1`
`204`	`204`	`#endif`
`205`	`205`	`#defineLED_GREEN LED_BUILTIN`
`206`	`206`	`#defineLED_BLUE PB7 // LD2`
`207`	`207`	`#defineLED_RED PB14 // LD3`
`208`	`208`
`209`	`209`	`// On-board user button`
`210`	`210`	`#ifndefUSER_BTN`
`211`		`-#defineUSER_BTN PC13`
	`211`	`+#defineUSER_BTN PC13`
`212`	`212`	`#endif`
`213`	`213`
`214`	`214`	`// Timer Definitions`
`215`	`215`	`// Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin`
`216`	`216`	`#ifndefTIMER_TONE`
`217`		`-#defineTIMER_TONE TIM6`
	`217`	`+#defineTIMER_TONE TIM6`
`218`	`218`	`#endif`
`219`	`219`	`#ifndefTIMER_SERVO`
`220`		`-#defineTIMER_SERVO TIM7`
	`220`	`+#defineTIMER_SERVO TIM7`
`221`	`221`	`#endif`
`222`	`222`
`223`	`223`	`// UART Definitions`
`224`	`224`	`#ifndefSERIAL_UART_INSTANCE`
`225`		`-#defineSERIAL_UART_INSTANCE 3 //Connected to ST-Link`
	`225`	`+#defineSERIAL_UART_INSTANCE 3 //Connected to ST-Link`
`226`	`226`	`#endif`
`227`	`227`
`228`	`228`	`// Serial pin used for console (ex: ST-Link)`
`229`	`229`	`// Required by Firmata`
`230`	`230`	`#ifndefPIN_SERIAL_RX`
`231`		`-#definePIN_SERIAL_RX PD9`
	`231`	`+#definePIN_SERIAL_RX PD9`
`232`	`232`	`#endif`
`233`	`233`	`#ifndefPIN_SERIAL_TX`
`234`		`-#definePIN_SERIAL_TX PD8`
	`234`	`+#definePIN_SERIAL_TX PD8`
`235`	`235`	`#endif`
`236`	`236`
`237`	`237`	`// HSE default value is 25MHz in HAL`
`238`	`238`	`// HSE_BYPASS is 8MHz`
`239`	`239`	`#ifndefHSE_BYPASS_NOT_USED`
`240`		`-#defineHSE_VALUE 8000000`
	`240`	`+#defineHSE_VALUE 8000000`
`241`	`241`	`#endif`
`242`	`242`
`243`	`243`	`// Extra HAL modules`
`244`	`244`	`#if !defined(HAL_DAC_MODULE_DISABLED)`
`245`		`-#defineHAL_DAC_MODULE_ENABLED`
	`245`	`+#defineHAL_DAC_MODULE_ENABLED`
`246`	`246`	`#endif`
`247`	`247`	`#if !defined(HAL_ETH_MODULE_DISABLED)`
`248`		`-#defineHAL_ETH_MODULE_ENABLED`
	`248`	`+#defineHAL_ETH_MODULE_ENABLED`
`249`	`249`	`#endif`
`250`	`250`	`#if !defined(HAL_QSPI_MODULE_DISABLED)`
`251`		`-#defineHAL_QSPI_MODULE_ENABLED`
	`251`	`+#defineHAL_QSPI_MODULE_ENABLED`
`252`	`252`	`#endif`
`253`	`253`	`#if !defined(HAL_SD_MODULE_DISABLED)`
`254`		`-#defineHAL_SD_MODULE_ENABLED`
	`254`	`+#defineHAL_SD_MODULE_ENABLED`
`255`	`255`	`#endif`
`256`	`256`
`257`	`257`	`/*----------------------------------------------------------------------------`
`@@ -274,6 +274,6 @@`
`274`	`274`	`//`
`275`	`275`	`// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX`
`276`	`276`	`// pins are NOT connected to anything by default.`
`277`		`-#defineSERIAL_PORT_MONITOR Serial`
`278`		`-#defineSERIAL_PORT_HARDWARE Serial`
	`277`	`+#defineSERIAL_PORT_MONITOR Serial`
	`278`	`+#defineSERIAL_PORT_HARDWARE Serial`
`279`	`279`	`#endif`

0 commit comments

Comments

(0)

Movatterモバイル変換

Navigation Menu

Search code, repositories, users, issues, pull requests...

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Uh oh!

Commit0de9d86

File tree

1 file changed

1 file changed

`‎variants/STM32H7xx/H742Z(G-I)T_H743Z(G-I)T_H747A(G-I)I_H747I(G-I)T_H750ZBT_H753ZIT_H757AII_H757IIT/variant_NUCLEO_H753ZI.h‎`

0 commit comments