|
| 1 | +#Use these commands in Kali to install required software: |
| 2 | +# sudo apt install python3-pip |
| 3 | +# pip install python-nmap |
| 4 | + |
| 5 | +# Import nmap so we can use it for the scan |
| 6 | +importnmap |
| 7 | +# We import the ipaddress module. We want to use the ipaddress.ip_address(address) |
| 8 | +# method to see if we can instantiate a valid ip address to test. |
| 9 | +importipaddress |
| 10 | +# We need to create regular expressions to ensure that the input is correctly formatted. |
| 11 | +importre |
| 12 | + |
| 13 | +# Regular Expression Pattern to extract the number of ports you want to scan. |
| 14 | +# You have to specify <lowest_port_number>-<highest_port_number> (ex 10-100) |
| 15 | +port_range_pattern=re.compile("([0-9]+)-([0-9]+)") |
| 16 | +# Initialising the port numbers, will be using the variables later on. |
| 17 | +port_min=0 |
| 18 | +port_max=65535 |
| 19 | + |
| 20 | +# This port scanner uses the Python nmap module. |
| 21 | +# You'll need to install the following to get it work on Linux: |
| 22 | +# Step 1: sudo apt install python3-pip |
| 23 | +# Step 2: pip install python-nmap |
| 24 | + |
| 25 | + |
| 26 | +# Basic user interface header |
| 27 | +print(r"""______ _ _ ______ _ _ |
| 28 | +| _ \ (_) | | | ___ \ | | | | |
| 29 | +| | | |__ ___ ___ __| | | |_/ / ___ _ __ ___ | |__ __ _| | |
| 30 | +| | | / _` \ \ / / |/ _` | | ___ \/ _ \| '_ ` _ \| '_ \ / _` | | |
| 31 | +| |/ / (_| |\ V /| | (_| | | |_/ / (_) | | | | | | |_) | (_| | | |
| 32 | +|___/ \__,_| \_/ |_|\__,_| \____/ \___/|_| |_| |_|_.__/ \__,_|_|""") |
| 33 | +print("\n****************************************************************") |
| 34 | +print("\n* Copyright of David Bombal, 2021 *") |
| 35 | +print("\n* https://www.davidbombal.com *") |
| 36 | +print("\n* https://www.youtube.com/davidbombal *") |
| 37 | +print("\n****************************************************************") |
| 38 | + |
| 39 | +# Ask user to input the ip address they want to scan. |
| 40 | +whileTrue: |
| 41 | +ip_add_entered=input("\nPlease enter the ip address that you want to scan: ") |
| 42 | +# If we enter an invalid ip address the try except block will go to the except block and say you entered an invalid ip address. |
| 43 | +try: |
| 44 | +ip_address_obj=ipaddress.ip_address(ip_add_entered) |
| 45 | +# The following line will only execute if the ip is valid. |
| 46 | +print("You entered a valid ip address.") |
| 47 | +break |
| 48 | +except: |
| 49 | +print("You entered an invalid ip address") |
| 50 | + |
| 51 | + |
| 52 | +whileTrue: |
| 53 | +# You can scan 0-65535 ports. This scanner is basic and doesn't use multithreading so scanning all the ports is not advised. |
| 54 | +print("Please enter the range of ports you want to scan in format: <int>-<int> (ex would be 60-120)") |
| 55 | +port_range=input("Enter port range: ") |
| 56 | +# We pass the port numbers in by removing extra spaces that people sometimes enter. So if you enter 80 - 90 instead of 80-90 the program will still work. |
| 57 | +port_range_valid=port_range_pattern.search(port_range.replace(" ","")) |
| 58 | +ifport_range_valid: |
| 59 | +# We're extracting the low end of the port scanner range the user want to scan. |
| 60 | +port_min=int(port_range_valid.group(1)) |
| 61 | +# We're extracting the upper end of the port scanner range the user want to scan. |
| 62 | +port_max=int(port_range_valid.group(2)) |
| 63 | +break |
| 64 | + |
| 65 | +nm=nmap.PortScanner() |
| 66 | +# We're looping over all of the ports in the specified range. |
| 67 | +forportinrange(port_min,port_max+1): |
| 68 | +try: |
| 69 | +# The result is quite interesting to look at. You may want to inspect the dictionary it returns. |
| 70 | +# It contains what was sent to the command line in addition to the port status we're after. |
| 71 | +# For in nmap for port 80 and ip 10.0.0.2 you'd run: nmap -oX - -p 89 -sV 10.0.0.2 |
| 72 | +result=nm.scan(ip_add_entered,str(port)) |
| 73 | +# Uncomment following line and look at dictionary |
| 74 | +# print(result) |
| 75 | +# We extract the port status from the returned object |
| 76 | +port_status= (result['scan'][ip_add_entered]['tcp'][port]['state']) |
| 77 | +print(f"Port{port} is{port_status}") |
| 78 | +except: |
| 79 | +# We cannot scan some ports and this ensures the program doesn't crash when we try to scan them. |
| 80 | +print(f"Cannot scan port{port}.") |