Repository files navigation

Building a Hackintosh on ROG STRIX Z490-G GAMING using OpenCore.

Although this mobo has a version with the built-in Wi-Fi card, it's CNVi based which means we cannot swap it. Since it's a MATX board, we can add one PCIe Wi-Fi card.

There are quite limiting choices for a fully-support PCIe Wi-Fi card:

Fenvi T919 is the best card among the bunch since it has 3 antennas for Wi-Fi and one for Bluetooth.

Although lack of 802.11ax (Wi-Fi 6) support, 3 streams MIMO together with 80MHz and 400ns GI make its maximum speed to 1.3 Gbps, above 2 streams MIMO 80MHz Wi-Fi 6's 1.2 Gbps speed found on the new Apple Silicon MacBook Pros.

If you're not using a Fenvi card, then you'll need two more kexts for it to work:

AirportBrcmFixup

BrcmPatchRAM

• BrcmBluetoothInjector
• BrcmFirmwareData
• BrcmPatchRAM3 for 10.14+, paired with BrcmBluetoothInjector

You need to put the required kexts in OC/Kexts. After that, runFile -> OC Snapshot in ProperTree and choose your OC folder so the new kexts will be loaded.

Note that some of the legacy cards may needpatch in macOS 12, try to avoid them if you can.

By default macOS will load AppleEthernetE1000 (Apple's DEXT driver) for I255-V, however, this kext will cause kernel panic on my board once the ethernet cable is plugged (Maybe works for you) . Therefore, we have to force loading AppleIntelI210Ethernet.kext in OpenCore using bootarge1000=0. macOS Ventura dropped AppleIntelI210Ethernet.kext, so we will add it as well.

This motherboard has several USB ports and they're defined as the following:

Image Source

For my personal use, I mapped SS03-04, SS07-08, SS09-10, HS11-12, and HS06 for Bluetooth due to the 15 ports limitation in macOS.

If you want to change the mapping, make your own USBMap.kext and replace the one in the OC/Kexts folder.

Few things need to be taken care of in the BIOS.

Note: In the newer version of BIOS, when enablingAbove 4G decoding, you may enableRe-size BAR Support if your hardware supports it. However, you need to make some changes to the config.plist, check out the Re-size BAR section. Make sure you connect the monitor to the dGPU.

If you do not set hardware acceleration correctly, DRM-related content will not play. Since we're using a discrete AMD GPU here, we can make use of AMD's own hardware acceleration coder.

In the terminal, type the following commands one by one.

defaults write com.apple.AppleGVA gvaForceAMDKE -bool YES

defaults write com.apple.AppleGVA gvaForceAMDAVCEncode -bool YES

defaults write com.apple.AppleGVA gvaForceAMDAVCDecode -bool YES

defaults write com.apple.AppleGVA gvaForceAMDHEVCDecode -bool YES

These should make hardware acceleration work correctly and have no problem playing back DRM content.

With the supported hardware, you may be able to enable re-size BAR in your BIOS under the PCI subsystem configuration tab in the BIOS.

macOS has no support for re-size BAR but starting from OpenCore 0.7.5, two quirks can be used to config it so that you can enjoy re-size BAR in Windows while not breaking macOS.

Booter >> Quirks >> ResizeAppleGpuBars: reduces GPU PCI BAR size to be compatible with macOS.

UEFI >> Quirks >> ResizeGpuBars: configure the GPU PCI BAR size for systems other than macOS.

ForResizeAppleGpuBars, you want to set it to0 if youenable re-size BAR and-1 ifdisable it. Other values may break macOS as discussedhere.

ForResizeGpuBars, it depends on your GPU's memory. Set it ton wheren is the minimal integer that makes2^n MB greater than or equal to the video memory you have.

For example, if I have 16GB video memory, then I should set it to14 since2^14 = 16384MB which is basically 16GB.

By default, the USB-C port on RX 6800 only has the functionality of video output and power delivery due to the fact that macOS loads a wrong kext calledAppleAMDUSBXHCIPCI.kext.

We'll use a custom kext based on XCHI-unsupported.kext calledXHCI-AMD6800.kext to force macOS loads the correct kextAppleUSBXHCIPCI.kext.

This repository contains EFI based on OpenCore 0.8.9. If you're using the same mobo, then this EFI is likely working for you. But if you have different parts other than mobo, please read the following content and modify it accrodingly.

You needProperTree to open and edit config.plist.

Since I have both iGPU and dGPU, I set it as output by dGPU and iGPU is only used for hardware accleration.

If you wish to use the iGPU as output, you'll need to changeAAPL,ig-platform-id from0300C89B to00009B3E.

PciRoot(0x0)/Pci(0x1C,0x4)/Pci(0x0,0x0) is used for tricking Apple's I225LM driver into supporting our I225-V network controller. If this does not work on your mobo, tryPciRoot(0x0)/Pci(0x1C,0x1)/Pci(0x0,0x0).

For Navi users(RX 5000/6000 series), you need to addagdpmod=pikera.

If you hate all the debug info when booting, you can also remove-v parameter but I suggest you remove it only when your hacking is up and running fine.

I left this part blank intentionally because you really need your own serial number.

To create a new serial number, you can useGenSMBIOS

As for SMBIOS, it depends on your CPU:

Using GenSMBIOS, you'll getType ,Serial ,Board Serial andSmUUID

Type goes to Generic -> SystemProductName

Serial goes to Generic -> SystemSerialNumber

Board Serial goes to Generic -> MLB

SmUUID goes to Generic -> SystemUUID

TL;DR You need your own serial number and if you have a different CPU or want to use iGPU as output, you need to change a few things in config.plist

Hardware Info

Geekbench 5

CPU Scores (M1 Max is around 1770 single and 12600 multi)

GPU Scores (Unstable due to the short benchmark period, can change from time to time)

Blackmagic Raw Speed Test