Repository files navigation

This is a replacement for a Milight/LimitlessLED remote/gateway hosted on an ESP8266. LeveragesHenryk Plötz's awesome reverse-engineering work.

Milight bulbs are cheap smart bulbs that are controllable with an undocumented 2.4 GHz protocol. In order to control them, you either need aremote ($13), which allows you to control them directly, or aWiFi gateway ($30), which allows you to control them with a mobile app or aUDP protocol.

This project is a replacement for the wifi gateway.

This guide on my blog details setting one of these up.

1. Both the remote and the WiFi gateway are limited to four groups. This means if you want to control more than four groups of bulbs, you need another remote or another gateway. This project allows you to control 262,144 groups (4*2^16, the limit imposed by the protocol).
2. This project exposes a nice REST API to control your bulbs.
3. You can secure the ESP8266 with a username/password, which is more than you can say for the Milight gateway! (The 2.4 GHz protocol is still totally insecure, so this doesn't accomplish much :).
4. Official hubs connect to remote servers to enable WAN access, and this behavior is not disableable.
5. This project is capable of passively listening for Milight packets sent from other devices (like remotes). It can publish data from intercepted packets to MQTT. This could, for example, allow the use of Milight remotes while keeping your home automation platform's state in sync. See the MQTT section for more detail.

The following remotes can be emulated:

Support has been added for the followingbulb types:

Other remotes or bulbs, but have not been tested.

1. An ESP8266. I used a NodeMCU.
2. A NRF24L01+ module (~$3 on ebay). Alternatively, you can use a LT8900.
3. Some way to connect the two (7 female/female dupont cables is probably easiest).

This project is compatible with both NRF24L01 and LT8900 radios. LT8900 is the same model used in the official MiLight devices. NRF24s are a very common 2.4 GHz radio device, but require software emulation of the LT8900's packet structure. As such, the LT8900 is more performant.

Both modules are SPI devices and should be connected to the standard SPI pins on the ESP8266.

This guide details how to connect an NRF24 to an ESP8266. By default GPIO 4 for CE and GPIO 15 for CSN are used, but these can be configured late in the Web GUI under Settings -> Setup.

Image source:MySensors.org

Connect SPI pins (CE, SCK, MOSI, MISO) to appropriate SPI pins on the ESP8266. With default settings, connect RST to GPIO 0, PKT to GPIO 16, CE to GPIO 4, and CSN to GPIO 15. Make sure to properly configure these if using non-default pinouts.

The goal here is to flash your ESP with the firmware. It's really easy to do this withPlatformIO:

export ESP_BOARD=nodemcuv2platformio run -e $ESP_BOARD --target upload

Of course make sure to substitutenodemcuv2 with the board that you're using.

You can find pre-compiled firmware images on thereleases.

This project usesWiFiManager to avoid the need to hardcode AP credentials in the firmware.

When the ESP powers on, you should be able to see a network named "ESPXXXXX", with XXXXX being an identifier for your ESP. Connect to this AP and a window should pop up prompting you to enter WiFi credentials. If your board has a built-in LED (or you wire up an LED), it willflash to indicate the status.

The network password is "milightHub".

Both mDNS and SSDP are supported.

• OS X - you should be able to navigate tohttp://milight-hub.local.
• Windows - you should see a device called "ESP8266 MiLight Gateway" show up in your network explorer.
• Linux users can installavahi (sudo apt-get install avahi-daemon on Ubuntu), and should then be able to navigate tohttp://milight-hub.local.

The HTTP endpoints (shown below) will be fully functional at this point. You should also be able to navigate tohttp://<ip_of_esp>, orhttp://milight-hub.local if your client supports mDNS. The UI should look like this:

If it does not work as expected seeTroubleshooting.

If you need to pair some bulbs, how to do this isdescribed in the wiki.

You can configure aliases or labels for a given(Device Type, Device ID, Group ID) tuple. For example, you might want to call the RGB+CCT remote with the ID0x1111 and the Group ID1 to be calledliving_room. Aliases are useful in a couple of different ways:

• In the UI: the aliases dropdown shows all previously set aliases. When one is selected, the corresponding Device ID, Device Type, and Group ID are selected. This allows you to not need to memorize the ID parameters for each lighting device if you're controlling them through the UI.
• In the REST API: standard CRUD verbs (GET,PUT, andDELETE) allow you to interact with aliases via the/gateways/:device_alias route.
• MQTT: you can configure topics to listen for commands and publish updates/state using aliases rather than IDs.

The REST API is specified using theOpenAPI v3 specification.

openapi.yaml contains the raw spec.

You can view generated documentation for the master branch here.

Docs for other branches can be found here

To configure your ESP to integrate with MQTT, fill out the following settings:

1. mqtt_server- IP or hostname should work. Specify a port with standard syntax (e.g., "mymqttbroker.com:1884").
2. mqtt_topic_pattern - you can control arbitrary configurations of device ID, device type, and group ID with this. A good default choice is something likemilight/:device_id/:device_type/:group_id. More detail is provided below.
3. (optionally)mqtt_username
4. (optionally)mqtt_password

mqtt_topic_pattern leverages single-level wildcards (documentedhere). For example, specifyingmilight/:device_id/:device_type/:group_id will cause the ESP to subscribe to the topicmilight/+/+/+. It will then interpret the second, third, and fourth tokens in topics it receives messages on as:device_id,:device_type, and:group_id, respectively. The following tokens are available:

1. :device_id - Device ID. Can be hexadecimal (e.g.0x1234) or decimal (e.g.4660).
2. :device_type - Remote type.rgbw,fut089, etc.
3. :group_id - Group. 0-4 for most remotes. The "All" group is group 0.
4. :device_alias - Alias for the given device. Note that if an alias is not configured, a default token__unnamed_group will be substituted instead.

Messages should be JSON objects using exactly the same schema that theREST gateway uses for the/gateways/:device_id/:device_type/:group_id endpoint.

Ifmqtt_topic_pattern is set tomilight/:device_id/:device_type/:group_id, you could send the following message to it (the below example uses a ruby MQTT client):

irb(main):001:0>require'mqtt'irb(main):002:0>client=MQTT::Client.new('10.133.8.11',1883)irb(main):003:0>client.connectirb(main):004:0>client.publish('milight/0x118D/rgb_cct/1','{"status":"ON","color":{"r":255,"g":200,"b":255},"brightness":100}')

This will instruct the ESP to send messages to RGB+CCT bulbs with device ID0x118D in group 1 to turn on, set color to RGB(255,200,255), and brightness to 100.

ESPMH is capable of providing two types of updates:

1. Delta: as packets are received, they are translated into the corresponding command (e.g., "set brightness to 50"). The translated command is sent as an update.
2. State: When an update is received, the corresponding command is applied to known group state, and the whole state for the group is transmitted.

To publish data from intercepted packets to an MQTT topic, configure MQTT server settings, and set themqtt_update_topic_pattern to something of your choice. As withmqtt_topic_pattern, the tokens:device_id,:device_type, and:group_id will be substituted with the values from the relevant packet.:device_id will always be substituted with the hexadecimal value of the ID. You can also use:hex_device_id, or:dec_device_id if you prefer decimal.

The published message is a JSON blob containing the state that was changed.

As an example, ifmqtt_update_topic_pattern is set tomilight/updates/:hex_device_id/:device_type/:group_id, and the group 1 on button of a Milight remote is pressed, the following update will be dispatched:

irb(main):005:0>client.subscribe('milight/updates/+/+/+')=>27irb(main):006:0>putsclient.get.inspect["lights/updates/0x1C8E/rgb_cct/1","{\"status\":\"on\"}"]

For this mode,mqtt_state_topic_pattern should be set to something likemilight/states/:hex_device_id/:device_type/:group_id. As an example:

irb(main):005:0>client.subscribe('milight/states/+/+/+')=>27irb(main):006:0>putsclient.get.inspect["lights/states/0x1C8E/rgb_cct/1","{\"state\":\"ON\",\"brightness\":255,\"color_temp\":370,\"bulb_mode\":\"white\"}"]irb(main):007:0>putsclient.get.inspect["lights/states/0x1C8E/rgb_cct/1","{\"state\":\"ON\",\"brightness\":100,\"color_temp\":370,\"bulb_mode\":\"white\"}"]

Make sure thatmqtt_topic_pattern,mqtt_state_topic_pattern, andmatt_update_topic_pattern are all different! If they are they same you can put your ESP in a loop where its own updates trigger an infinite command loop.

You can select which fields should be included in state updates by configuring thegroup_state_fields parameter. Available fields should be mostly self explanatory, but are all documented in the REST API spec underGroupStateField.

To receive updates when the MQTT client connects or disconnects from the broker, confugre themqtt_client_status_topic parameter. A message of the following form will be published:

{"status":"disconnected_unclean","firmware":"milight-hub","version":"1.9.0-rc3","ip_address":"192.168.1.111","reset_reason":"External System"}

If you wish to have the simple messagesconnected anddisconnected instead of the above environmental data, configuresimple_mqtt_client_status totrue (or set Client Status Message Mode to "Simple" in the Web UI).

You can add an arbitrary number of UDP gateways through the REST API or through the web UI. Each gateway server listens on a port and responds to the standard set of commands supported by the Milight protocol. This should allow you to use one of these with standard Milight integrations (SmartThings, Home Assistant, OpenHAB, etc.).

You can select between versions 5 and 6 of the UDP protocol (documentedhere). Version 6 has support for the newer RGB+CCT bulbs and also includes response packets, which can theoretically improve reliability. Version 5 has much smaller packets and is probably lower latency.

Transitions between two given states are supported. Depending on how transition commands are being issued, the duration and smoothness of the transition are both configurable. There are a few ways to use transitions:

These routes are fully documented in theREST API documentation.

When you issue a command to a bulb either via REST or MQTT, you can include atransition field. The value of this field specifies the duration of the transition, in seconds (non-integer values are supported).

For example, the command:

{"brightness":255,"transition":60}

will transition from whatever the current brightness is tobrightness=255 over 60 seconds.

• espMH's transitions should work seamlessly withHomeAssistant's transition functionality.
• You can issue commands specifying transitions between many fields at once. For example:

  {"brightness":255,"kelvin":0,"transition":10.5}

  will transition from current values for brightness and kelvin to the specified values -- 255 and 0 respectively -- over 10.5 seconds.
• Color transitions are supported. Under the hood, this is treated as a transition between current values for r, g, and b to the r, g, b values for the specified color. Because milight uses hue-sat colors, this might not behave exactly as you'd expect for all colors.
• You can transition to a givenstatus orstate. For example,

  {"status":"ON","transition":10}

  will turn the bulb on, immediately set the brightness to 0, and then transition to brightness=255 over 10 seconds. If you specify a brightness value, the transition will stop there instead of 255.

Some ESP boards have a built-in LED, on pin #2. This LED will flash to indicate the current status of the hub:

• Wifi not configured: Fast flash (on/off once per second). SeeConfigure Wifi to configure the hub.
• Wifi connected and ready: Occasional blips of light (a flicker of light every 1.5 seconds).
• Packets sending/receiving: Rapid blips of light for brief periods (three rapid flashes).
• Wifi failed to configure: Solid light.

In the setup UI, you can turn on "enable_solid_led" to change the LED behavior to:

• Wifi connected and ready: Solid LED light
• Wifi failed to configure: Light off

Note that you must restart the hub to affect the change in "enable_solid_led".

You can configure the LED pin from the web console. Note that pin means the GPIO number, not the D number ... for example, D1 is actually GPIO5 and therefore its pin 5. If you specify the pin as a negative number, it will invert the LED signal (the built-in LED on pin 2 (D4) is inverted, so the default is -2).

If you want to wire up your own LED you can connect it to D1/GPIO5. Put a wire from D1 to one side of a 220 ohm resistor. On the other side, connect it to the positive side (the longer wire) of a 3.3V LED. Then connect the negative side of the LED (the shorter wire) to ground. If you use a different voltage LED, or a high current LED, you will need to add a driver circuit.

Another option is to use an external LED parallel to the (inverted) internal one, this way it will mirror the internal LED without configuring a new LED pin in the UI. To do this connect the (short) GND pin of your LED to D4. The longer one to a 220 ohm resistor and finally the other side of the resistor to a 3V3 pin.

This project is developed and built usingPlatformIO.

On-board unit tests are available using PlatformIO. Run unit tests with this command:

pio test -e d1_mini

substitutingd1_mini for the environment of your choice.

A remote integration test suite built using rspec is available under./test/remote.

h4nc (h4nc.zigbee(a)gmail.com) created a PCB and 3D-printable case for espMH. He's offering ready-made versions. Please get in touch with him at the aforementioned email address for further information.

Find more information from theespmh_pcb repository.

• @WoodsterDK added support for LT8900 radios.
• @cmidgley contributed many substantial features to the 1.7 release.

If the project brings you happiness or utility, it's more than enough for me to hear those words.

If you're feeling especially generous, and are open to a charitable donation, that'd make me very happy. Here are some whose mission I support (in no particular order):

• Water.org
• Brain & Behavior Research Foundation
• Electronic Frontier Foundation
• Girls Who Code
• San Francisco Animal Care & Control