Atip jet is a jetnozzle at the tip of somehelicopter rotor blades, used to spin the rotor, much like aCatherine wheel firework.[1] Tip jets replace the normal shaft drive and have the advantage of placing notorque on the airframe, thus not requiring the presence of a tail rotor. Some simplemonocopters are composed of nothing but a single blade with a tip rocket.[2][3]
Tip jets can use compressed air, provided by a separateengine, to create jetthrust. Other types use a system that functions similarly to theafterburner (reheat) on a conventional jet engine, except that instead of reheating a gas jet, they serve as the primary heater, creating greater thrust than the flow of pre-compressed air alone; the best description of this isthrust augmentation. Other designs includesramjets or even a complete turbojet engine. Some, known asrocket-on-rotor systems, involve placing rockets on the tips of the rotor blades that are fueled from a tank.[4]
If the helicopter's engine fails, the tip jets on the rotor increase themoment of inertia, hence permitting it to store energy, which makes performing a successfulautorotation landing somewhat easier. However, the tip jet also typically generates significant extra air drag, which demands a higher sink rate and means that a very sudden transition to thelanding flare must occur for survival, with little room for error.
During the 1900s, AustrianLudwig Wittgenstein investigated the use of tip jets to drive anaircraft propeller while studyingaeronautical engineering atManchester University, in the United Kingdom. Wittgenstein's concept required air and gas to be forced along the propeller arms to combustion chambers on the end of each blade, at which point these gases would undergo compression via the centrifugal force exerted by the revolving arms, and thereby generating sufficient heat to achieve ignition.[5] During 1911, Wittgenstein was able to secure apatent related to his tip jet work.[6]
Despite the relatively early origins of the concept, achieving the next step of practical application proved to be highly difficult, largely due to propeller designs of the era being relatively primitive and incompatible with the design changes required to implement Wittgenstein's tip jets. It would be many years before a blade design that could support the innovation would be developed. Propellers of the period were typically wood, whereas more recent propeller blades are typically composed ofcomposite materials orpressed steel laminates; the latter is manufactured as separate halves before being welded together, giving the blade a hollow interior and therefore an ideal pathway to channel the air and gas for a tip jet.[5] Progress on the jet-powered propeller was further frustrated by Wittgenstein's lack of practical experience with machinery.[7] He ultimately lost interest in aviation and discontinued his engineering work. Wittgenstein would become better known for his later work as aphilosopher.[8]
During the 1920s, the Italian aeronautical engineerVittorio Isacco designed and constructed several unorthodox rotorcraft which became known as theHelicogyre. During 1929, HelicogyreK1171 was manufactured by British aircraft manufacturerS.E. Saunders Limited, and was delivered to theRoyal Aircraft Establishment (RAE) at Farnborough by road, where it underwent limited testing before the programme was terminated.[9][10] Although the Helicogyre did not use tipjets, being instead powered by piston engines positioned at the ends of the rotary wing, Isacco foresaw that these might be replaceable by jets.[11]
Another pioneer in the field of tip jets was the Russian-American engineerEugene Michael Gluhareff, the inventor of theGluhareff Pressure Jet.[12]
During theSecond World War, German engineerFriedrich von Doblhoff suggested powering a helicopter withramjets located on the rotor tips. His idea was taken forwards and, during 1943, theWNF 342 V1 became the first tip jet-powered helicopter; it used a conventional piston engine to drive both a compact propeller and anair compressor to provide air (subsequently mixed with fuel) via channels in the rotor head and the hollow rotor blades to combustion chambers set at the rotor tips.[13] In addition to the WNF 342's experimental use by Germany, two prototypes were obtained by theUnited States as the conflict came to a close.[14]
Subsequently, Doblhoff joined the American aircraft manufacturerMcDonnell Aircraft, which developed and flew theMcDonnell XV-1, an experimentalcompound gyroplane, during the early 1950s. This rotorcraft was classified as aconvertiplane; the propulsion system was powered by a singleContinental-builtR-975radial engine that powered a pair of air compressors to feed high-pressure air through piping in the rotor blades to a combustion chamber on each of the three rotor tips, where a burner ignited fuel for increased thrust, which drove the rotors around and allowed the vehicle to fly in a manner akin to a conventional helicopter.[15] However, while flying horizontally, the compressors were disconnected from the engine, which instead drove a two-bladed pusher propeller; in forward flight, 80 percent of the lift was provided by the wing, while the remainder was generated by the main rotor thatautorotating at about 50 percent of its rpm when directly powered.[16][17] The XV-1 was cancelled due to its unfavourable complexity and rapid advances made by conventional helicopters.[18]
The engineerAugust Stepan has been credited with producing the tip jet engines used by the British aircraft manufacturing interestFairey Aviation.[citation needed] Following the Second World War, Fairey Aviation was keen to explore rotary-wing aircraft, developing theFairey FB-1 Gyrodyne in accordance withSpecification E.16/47.[19] The second FB-1 was modified to investigate a tip-jet driven rotor coupled with a pair of propellers mounted on stub wings; it was later renamed theJet Gyrodyne.[20] Another rotorcraft developed by the firm, theFairey Ultra-light Helicopter was a compact side-by-side two-seater vehicle that used tip jets powered by a singleTurbomeca Palousteturbojet engine.[21] The type led a contract from theMinistry of Supply for four flight test-capable aircraft; the Ultra-light's capabilities were subsequently demonstrated at numerous military exercises, airshows, and even at sea.[21] However, the British Army had become more focused on the rivalSaunders-Roe Skeeter, allegedly due to interest in the latter from the German government.[22]
Drawn to a specification produced by the airlineBritish European Airways (BEA) for a passenger-carrying rotorcraft, referred to theBEA Bus,[23] Fairey set about developing theFairey Rotodyne. On 6 November 1957, the Rotodyne prototype performed itsmaiden flight, piloted by chief helicopter test pilotSquadron Leader W. Ron Gellatly and assistant chief helicopter test pilotLieutenant Commander John G.P. Morton as second pilot.[24][25] On 10 April 1958, the Rotodyne made its first successful transition from vertical to horizontal and then back into vertical flight.[25][26] On 5 January 1959, the Rotodyne set a world speed record in the convertiplane category, at 190.9 mph (307.2 km/h), over a 60-mile (100 km) closed circuit.[27][28]
Both BEA and the RAF had publicly announced their interest in the Rotodyne, the latter placing an initial order for the type.[29] Reportedly, the larger Rotodyne Z design could be developed to accommodate up to 75 passengers and, when equipped withRolls-Royce Tyne engines, would have a projected cruising speed of 200 knots (370 km/h). It would be able to carry nearly 8 tons (7 tonnes) of freight; cargoes could have included severalBritish Army vehicles and the intact fuselage of some fighter aircraft within its fuselage.[30] Despite much of the development work being completed, the British government declared it would issue no further support for the Rotodyne due to economic reasons. Accordingly, on 26 February 1962, official funding for the Rotodyne was terminated.[31][32]
The French aircraft manufacturerSud-Ouest would be the first company to achieve quantity production of a rotorcraft harnessingtip-jet propulsion.[33] Having initially developed the tip jet-equippedSud-Ouest Ariel for purely experimental purposes, the firm had sufficient confidence to proceed with a production-standard rotorcraft, theSud-Ouest Djinn.[34] A single seat prototype, designatedS.O.1220, was constructed to function as an aerial test bed for the rotorcraft's propulsion concept.[35][36] TheFrench Army encouraged the construction of a large pre-production batch of 22 helicopters for evaluation purposes. The first of these flew on 23 September 1954. Three pre-production rotorcraft were acquired by theUnited States Army, designating itYHO-1, for their own trials; according to aviation author Stanley S. McGowen, the US Army held little interest in the type.[37] According to author Wayne Mutza, the US Army had found the YHO-1 to be an excellent weapons platform, but were compelled to abandon its interest by political opposition to the procurement of a foreign designed rotorcraft.[38]
In addition to the French military, a further ten countries placed orders for the type; such as a batch of six rotorcraft which were procured by theGerman Army.[37] Production of the Djinn came to an end during the mid-1960s, by which point a total of 178 Djinns had been constructed; the type had effectively been replaced by the more conventional and highly successfulAérospatiale Alouette II.[34][39] Some Djinns were sold on to civil operators; in this capacity, they were often equipped foragricultural purposes, fitted with chemical tanks and spray bars.[37] During the late 1950s, an improved version of the Djinn, tentatively designated as theDjinn III orSuper Djinn, was being studied by Sud Aviation. As envisioned, the projected Super Djinn would have adopted the newerTurbomeca Palouste IV engine alongside other changes for greater power and endurance than the original production model.[33][40]
The compressed air in cold tip jets generally exited at quite high temperatures due to compression-heating effects, but they are referred to as "cold" jets[citation needed] to differentiate them from jets that burn fuel to heat the air for greater thrust; similar to the difference between the "cold" and "hot" exhausts on theHarrier "jump jet", which uses "cold" air heated to several hundred degrees by compression inside the low-pressure compressor of thePegasus engine.)
Hot tip jets in this context are a form of simple pressure fedrocket engine as both fuel and oxidizer are being supplied, mixed, and ignited. Typically the oxidizer used here is air that has been compressed elsewhere in the aircraft and ducted through the rotor to the tip thruster along with fuel.
(Note: Fuel and oxidiser supplied to combustion chambers at the rotor tips.)