Aswingarm (or swinging arm), originally known as a swing fork or pivoted fork, is a single or double sided mechanical device which attaches the rear wheel of amotorcycle to its body, allowing it to pivot vertically. The main component of the rearsuspension of most modern motorbikes andATVs, it holds the rearaxle firmly, while pivoting to absorb bumps and suspension loads induced by the rider, acceleration, and braking.
Originally motorcycles had no rear suspension, as their frames were little more than stronger versions of the classicdiamond frame of a bicycle. Many types of suspension were tried, includingIndian'sleaf spring suspended swingarm, andMatchless'scantileveredcoiled-spring swingarm. Immediately before and after World War II, theplunger suspension, in which the axle moved up and down two vertical posts, became commonplace. In the latter, the movement in each direction was against coiled springs.
Some manufacturers, such as Greeves, used swingarm designs for the front forks, which were more robust thantelescopic forks. In particular,sidecar motocross outfits frequently use swingarm front forks. The swingarm has also been used for the front suspension ofscooters. In this case it aids in simplifying maintenance. In motorcycles with shaft drive, such as theYamaha XJ650 Maxim, the shaft housing forms the left side swingarm.
Swingarms can be single or double sided, and have appeared in a variety of geometries. Many single-sided also incorporate the driveshaft.
Swinging fork - the original version consisting of a pair of parallel pipes holding the rear axle at one end and pivoting at the other. A pair ofshock absorbers are mounted just before the rear axle and attached to the frame, below the seat rail.
Cantilever - An extension of the swinging fork where a triangulated frame transfers swingarm movement to compress shock absorber/s generally mounted in front of the swingarm. The HRD-Vincent Motorcycle is a famous early form of this type of swingarm, thoughMatchless used it earlier, andYamaha subsequently. TheHarley-DavidsonSoftail is another form of this swingarm, though working in reverse, with the shock absorbers being extended rather than compressed.
Parallelogram - Was first introduced commercially in 1985 on the Magni "Le Mans". Magni called the systemParallelogrammo. Various parallelogram systems have been developed by other manufacturers.[1]
Whereas downward generated mechanical forces would cause a chain-driven bike to"squat" at the rear under acceleration,[2] the torque reaction of a shaft drive machine would induce the opposite, causing the seat (and rider) to rise upwards, a phenomenon known as"shaft-jacking". This anti-intuitive sensation can be disconcerting to riders, which parallelogram suspensions seek to neutralize.
BMW introduced itsParalever system on its 1988 R80GS and R100GS motorcycles, which adds a second link between the rear drive and transmission to allow the driveshaft to pivot along the same axis as the sprung rear frame.
Moto Guzzi patented itsCompact Reactive Drive Shaft system (Ca.R.C.), where the driveshaft is free to float into its structure, providing much softer feedback from transmission.[citation needed] An upper arm serves as a guide to close the geometry of the suspension.[clarification needed]
Extended swingarms - are often used bydrag racing motorcycles (called dragbikes) to keep theircenter of gravity as forward as possible, which reduces the tendency towheelie at the start.
Single-sided swingarm - a suspension lying along only one side of the rear wheel, allowing it to be mounted to a hub like a car wheel. Also found onscooters, where a robust chain case doubles as the swingarm linking the engine and rear wheel, single-sided swingarms need to be much stiffer and more heavily built than double-sided, to accommodate the extra torsional forces. Having a single mounting point guarantees proper wheel alignment.[citation needed]
Single-sided swingarms date from at least the late 1940s. In 1948, theImme R100 produced byNorbert Riedel of Germany had both a single-sided front wheel suspension as well as a single-sided rear swingarm that doubled as the exhaust pipe.[3] In 1950 Moto Guzzi introduced the Galletto, a large-wheel step-through scooter. In 1980,BMW introduced its first single-sided swingarm on theR80G/S, the "Mono-lever", which was superseded by the "Para-lever" used currently.Honda currently features this style of swingarm on theHonda VFR.Ducati has created several models featuring single swingarms, most notably theMassimo Tamburini-designed916 series. While Ducati abandoned this style for the999, the company returned to it for the1098 superbike in 2007, and it survives in the currentDucati 1199. TheTriumph Sprint ST andSpeed Triple also feature single-sided swingarms.[4]
"Squat" occurs because the top of the final drive chain run pulls the swingarm upwards; "shaft-jacking" occurs because the shaft drive bevel gear tries to "climb up" the large bevel gear in the wheel hub, thereby pushing the swingarm downwards and away from the frame.[5]
Shaft-jacking can be minimised by devices such as parallelogram swingarms. A practical way to minimise squat on a chain-drive bike is to locate the final drive sprocket as close as possible to the axis of the swingarm pivot; the ideal solution is to make the final drive sprocket and the swingarm pivot concentric, as was done on theHesketh V1000.
This enabled the longish exhaust pipe to double as a single-sided swing arm for the rear wheel!
| Chassis |  | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| Engine |
| ||||||||
| Transmission |
| ||||||||
| Accessories | |||||||||
| Other | |||||||||