 | This articlerelies largely or entirely on asingle source. Relevant discussion may be found on thetalk page. Please helpimprove this article byintroducing citations to additional sources. Find sources: "Rockwell PPS-4" – news ·newspapers ·books ·scholar ·JSTOR(November 2025) |
 PPS-4/1 single-chip model | |
| General information | |
|---|---|
| Launched | 1972; 54 years ago (1972) |
| Discontinued | 1990s |
| Common manufacturer |
|
| Performance | |
| Max.CPUclock rate | 256 kHz |
| Data width | 8 instruction, 4 data |
| Address width | 12 |
| Physical specifications | |
| Package |
|
TheRockwell PPS-4, short for "Parallel Processing System, 4-bit", was an early4-bitmicroprocessor fromRockwell International, released in late 1972. Although practically unknown today, the PPS series was widely used in calculators, games and toys, and other embedded applications. Updated versions continued to be produced into the 1980s.
The original version was implemented in a three-chip set, consisting of the CPU, a clock generator, and a user ROM. In 1975, the clock generator was integrated to produce thePPS-4/2 with a variety of ROM and RAM support chips. In 1976, thePPS-4/1 added user-customized ROM to produce a single-chip solution, running at a lower speed.
The release of the PPS-4/1 coincided with the release of theRockwell PPS-8, a more advanced8-bit processor. Support chips released for the PPS-8 also worked with the PPS-4/1. These versions of the lineup continued to be produced into the 1980s. The PPS-8, however, was abandoned shortly after its introduction as more advanced 8-bit processors entered the market.
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The PPS-4 was built on ametal gate process, compared to the contemporaryIntel 4004 which was based on the more advancedsilicon gatePMOS logic process. This required high voltages; it ran on a -17 VDC power supply while running at only 256 kHz, whereas the 4004 ran at 750 kHz on a 15 VDC supply.
The CPU, part number 10660,[a] was packaged in a 42-pinquad in-line package. The pins included a 12-pinaddress bus, 8-pindata bus and three 4-pininput/output ports that could be combined in different ways. Power supply and clock signals took up the rest of its 42 pins.[1]
PPS-4's separate data and address buses meant it could read an 8-bit instruction in a single cycle. In contrast, the 16-pin 4004 had a single 4-bit bus multiplexed five ways, meaning specifying a 12-bit address required externallatches and three cycles to specify the address and then two cycles to read an instruction. This meant the PPS-4 performed at roughly the same overall speed as the 4004 despite running at a third the clock speed.[2]
A complete system used the 10660 CPU, the 10706 clock generator in a 10-pinTO-5 package, and one of a variety of ROM or RAM chips. The clock was four-phase[3] and based on a standardNTSC crystal due to their widespread availability.
The PPS-4/2 was introduced in the autumn of 1975, combining the clock chip onto the die and reducing the system to two chips, the 11660 CPU and a ROM or RAM. It also had a built-inLED controller. This would normally be used with the Memory/IO System chip, which combined 2 KB of ROM, 128 bytes of RAM, and 16 serial ports that could be combined in various ways.
The PPS-4/1 followed in early 1976, staying with the PMOS process while most other companies had since moved to the newNMOS logic. This was designed to work with the recently released PPS-8, which also used the PMOS process. The two were designed to work with a common set of interface chips. A wide variety of PPS-4/1 models were produced, with different amounts of RAM, ROM and I/O ports build into the die. These versions ran much slower than the original models, between 40 and 120 kHz.