River Irwell Railway Bridge | |
|---|---|
 | |
| Coordinates | 53°28′40″N2°15′36″W / 53.4779°N 2.2599°W /53.4779; -2.2599 |
| Crosses | River Irwell |
| Locale | Manchester, England |
| History | |
| Designer | George Stephenson |
| Constructed by | George Stephenson |
| Opened | 1 January 1830 (1830-01-01) |
Listed Building – Grade I | |
| Official name | Railway Bridge over River Irwell to Former Liverpool Road Station |
| Designated | 19 June 1988 |
| Reference no. | 1270603 |
| Location | |
 Interactive map of River Irwell Railway Bridge | |
TheRiver Irwell Railway Bridge was built for theLiverpool & Manchester Railway (L&MR), the world's first passenger railway which used only steam locomotives and operated as a scheduled service, near Water Street inManchester, England. The stone railway bridge, built in 1830 byGeorge Stephenson, was part ofLiverpool Road railway station.[1] The bridge was designated aGrade I listed building on 19 June 1988.[1]
The bridge was built by the L&MR on its line betweenLiverpool and Manchester. The bridge spanned the Irwell just before the terminus at Liverpool Road and was not part of the original plan. Construction was marred by an accident in April 1830 when eleven workers were drowned after an overcrowded boat sank after colliding with acofferdam being used in the construction of the bridge's central pier.[2] On 15 September 1830, the L&MR opened the line and the bridge.
In 2016, the bridge was restored as part of the programme to construct theOrdsall Chord, but the railway line severed the link between the bridge, which remains in use, and the former Liverpool Road Station.
The River Irwell Bridge was built by theLiverpool & Manchester Railway who built the world's first intercity railway betweenLiverpool andManchester.[2] During 1829,parliament authorised a variation to the intended route of the railway which was planned to terminate inSalford. The route was extended into Manchester necessitating a bridge over theRiver Irwell to astation at the west end of Liverpool Road. The bridge was probably designed byGeorge Stephenson, the L&MR's chief engineer but elements of its design may have originated fromJesse Hartley orThomas Longridge Gooch.[2]
The bridge is a masonry skew arch bridge, with two equal arches of 20.1 metres (66 ft) skew span, 19.7 metres (65 ft) square span, and 16.2 metres (53 ft) between the parapets. The bridge carries a twinstandard gauge track layout and a 5.5-metre (18 ft) wide roadway. The decision to include a road is alleged to have been made in the face of opposition by theMersey and Irwell Navigation Company who had objected to the bridge's construction because of the bridge pier in the centre of the river. This central pier was constructed by workers inside acofferdam; workers were ferried between the pier and the river banks by boat. In April 1830, an overcrowded boat collided with the cofferdam and sank and eleven workers drowned.[2]
The navigation company insisted that the bridge should clear the water by at least 8.8 metres (29 ft). The clearance meant that the railway line would be high above ground level on the Manchester bank and a brick viaduct was built to carry the line over Water Street governing the location of the platforms at Liverpool Road Station.[2]
The bridge has "two segmental arches on a slightly skewed plan".[3] Its span measures 66 feet (20 m).[2] The bridge is built ofsandstone with rusticatedashlar facings and radiating stonework that frames the arches and forms the spandrel panels. Horizontal stone courses make up the parapet and the pilasters of the central cutwater and span ends, and the coping and cornices are made of plainly dressed stonework.[2]
On 15 September 1830, the bridge was opened, along with the L&MR line. During 1849 an adjacent two-span bridge was constructed to carry theManchester South Junction and Altrincham Railway over the Irwell. Located to the south, it was built ofmasonry and follows a broadly similar alignment.[2] During 1869, a plate-iron-girder viaduct, was constructed at an angle near to the bridge's northern side. The viaduct had a large circular cast-iron support column set on a central river pier. It has been demolished, although proposals for its reinstatement have been mooted.[2]
Over time, the underside of the bridge has been covered bystalactites, some reportedly up to 230 mm (9.1 in) in length. They are the result of the moist environment leachinglime from mortar between the masonry blocks. Efforts to remove them have been conducted in the past.[2]
During June 1988, the Manchester side of the rail bridge was designated a Grade Ilisted structure. The Salford end was not designated until February 2007. The bridge designated for its "special architectural and historic interest due to its early date, intactness, and design by George Stephenson, the nationally renowned railway engineer".[2]
To improve railway services in the north of England, theNorthern Hub programme proposed a link betweenVictoria,Oxford Road andPiccadilly requiring the construction of a 1 kilometre (0.62 mi) link, theOrdsall Chord. A section of the chord is carried on a viaduct across the Irwell, where it bisects the Manchester end of the Irwell bridge approach and the original L&MR tracks into theMuseum of Science & Industry (the formerLiverpool Road Station, which was closed to traffic in 1975 and opened as a museum in 1983), severing the former station's connection to the railway network. The chord forms a curve that connects the Castlefield and Deal Street Junctions. Following legal challenges its construction was officially sanctioned. The viaduct that covered Irwell bridge's north-eastern face was demolished, revealing the bridge's full elevation. By October 2016, the arch soffits had been cleaned and all the stalactites removed.[2]
