Lancia Appia
Lancia Appia Berlina, second series
Overview
Manufacturer	Lancia
Production	1953–1963
Designer	Pinin Farina (Coupé) Giovanni Michelotti atVignale (Convertibile and Lusso)[1] Zagato (Appia Zagato)
Body and chassis
Class	Small family car
Body style	4-doorsaloon 2-door saloon (Vignale) 2-doorcoupé (Pinin Farina) 2-door coupé (Zagato) 2-doorconvertible (Vignale) 3-doorestate (Viotti)
Layout	Front-engine, rear-wheel-drive
Related	Lancia Aurelia
Powertrain
Engine	1.1 LLanciaV4 (petrol)
Transmission	4-speedmanual
Dimensions
Wheelbase	2,480 mm (97.6 in) S. 1 2,510 mm (98.8 in) S. 2, S. 3
Length	3,865 mm (152.2 in) 4,010 mm (157.9 in) S. 2 4,020 mm (158.3 in) S. 3
Width	1,420 mm (55.9 in) 1,485 mm (58.5 in) S. 2 1,390 mm (54.7 in) S. 3
Height	1,422 mm (56.0 in) 1,405 mm (55.3 in) S. 2 1,450 mm (57.1 in) S. 3
Kerb weight	820–920 kg (1,808–2,028 lb)
Chronology
Predecessor	Lancia Ardea
Successor	Lancia Fulvia

TheLancia Appia is apassenger car introduced in 1953 by Italian car manufacturerLancia as a replacement for theArdea, and which remained in production for ten years.The Appia was the last in a long line ofLancia production cars dating back to the LanciaLambda (introduced in 1922) to usesliding pillar front suspension.^[2] All three series produced had a 1089ccLancia V4 engine.

In addition to the saloon, a number of special bodied Appias were produced, including a coupé by Pinin Farina, a convertible and 2-door saloon byVignale and an aluminium-bodied GT byZagato, as well aslight commercial vehicle variants.In total 107,000 Appia were built: 98,000 saloons, 3,863 commercial vehicles, and 5,161 chassis supplied to coachbuilders.

In 1950 Lancia had introduced its first all-newpostwar model, theLancia Aurelia, a small but expensive luxury car with sophisticated engineering features like thefirst ever V6 engine,inboard rear brakes and atransaxle gearbox. Alongside it Lancia was still producing theLancia Ardea, a pre-war design that although once innovative was in need of replacement.The new small Lancia was designed under engineerVittorio Jano. Initially an updated version of the Ardea's 17° V4 engine was considered, but a clean-sheet design was ultimately chosen. At little over 10°, the new V4 had the narrowest angle of any V4 engine, and used solutions unprecedented at Lancia, like dual in-block camshafts in place of overhead ones. As the Ardea resembled a scaled-downAprilia, the Appia mimicked the Aurelia's appearance, substituting its exotic parts with more cost-effective ones, such as a solid axle and a four-speed gearbox in block with the engine. For its mechanical features—sliding pillar front suspension, V4 engine, rear-wheel drive, absence of a centre pillar—the Appia can be considered the last in a line of Lancias which stretched back to the 1922Lambda. Following a custom started in the postwar years, the new model was named after a Romanconsular road, theAppian Way.

The Appia Berlina (saloon/sedan) was introduced in April 1953 at theTurin Motor Show.^[3]The chassis code is C10 for theright hand drive saloon—the standard version, as was customary at Lancia—and C10S (fromSinistra, Italian for "left") for theleft hand drive variant, available on request.Under the Appia's bonnet there is a 38 PS 1.1-litre engine, which according to the manufacturer could push the car to 120 km/h (75 mph).^[3] The body style is similar to theLancia Aurelia. To save weight the doors and rear fenders of the first few thousand examples were aluminium.^[3] The bumpers were also aluminium, making them easily dented. Rubber stripping was added later, to protect them from minor impacts.^[3]In a design inaugurated by the 1933Lancia Augusta, rear doors were aft-hingedsuicide doors, eliminating theB-pillar. A spare tyre, the fuel filler and the battery were located in the trunk/boot.The interior featured bucket front seats, acolumn-mounted shifter, ivory plastic steering wheel and switches, andpanno Lanciawool cloth upholstery in grey or beige. Running on 155HR15 Pirelli Cinturato tyres.In total 20,025 first series saloons were made, from 1953 to 1956.^[3] Of these, the majority—10,257—were right hand drive, and the remaining 9,768 left hand drive.^[4]

The Appia sold in smaller numbers than projected.^[5][6] In 1956, Italian car magazineQuattroruote attributed this to the price, competition from theFiat 1100/103 andAlfa Romeo Giulietta, and a host of minor flaws,^[5][6] e.g., the aluminium bumpers (which however were shared with early Aurelias) — indicating a hasty, low-priority development when Lancia was diverting many of its limited resources to itssports car racing efforts.^[5][6]

Comparison of first (top) and second series rear views

In April 1955 engineerAntonio Fessia joined Lancia astechnical director, and started off fixing the Appia's shortcomings.^[5][6] Jano left shortly after, when Lanciawithdrew from Formula 1.The resulting second series Appia, introduced at theGeneva Motor Show in March 1956, had a more powerful engine, a modernized body and better interior room, although the bucket seats were replaced with a bench seat and there was a considerable weight increase, which largely cancelled out the increase in power . The C10 and C10S type codes were kept.The rear part of the body had been redesigned to enlarge the boot, and the wheelbase was stretched by 3 cm (1.2 in) to provide better rear seat accommodation; this resulted in a 14.5 cm (5.7 in) growth in length. From the front the second series could be recognized from its rectangular instead of round turn signal lamps and the steel bumpers with overriders. The fuel filler cap was moved outside, under a locking flap on the right hand side rear wing. Fessia's changes to the engine included lowering thecompression ratio, redesigning thecylinder head incorporatinghemispherical combustion chambers and a new arrangement of the valves, new pistons, a new carburettor and different camshaft profiles.^[4][7] Output increased to 43 PS, and top speed to 120 km/h (75 mph).^[4] In the cabin a frontbench seat took place of the two single ones, the binnacle held two round instruments, and steering wheel and switchgear went from ivory to black.

Despite—previously critical—Quattroruote having declared the Appia "finally accomplished and convincing",^[8] sales did not take off yet. In May 1958 daily production still lingered at 27 cars per day, far short of the 50 anticipated during the car's development.^[9][6] In total 22,425 second series saloons were made, only 3,180 of them C10 right hand drive cars.^[4]

In March 1959, the third series Appia was introduced at theGeneva Motor Show with a new front end.^[4] Lancia's traditional radiator shell-style grille was ultimately abandoned, in favour of an horizontal one inspired by theLancia Flaminia flagship. Engine power went up again to 48 PS, as did top speed, to 132 km/h (82 mph).^[4] The braking system was improved with twin leading shoe frontdrum brakes and a "Duplex" dual hydraulic circuit during the 1960 model year. Model designations were different from the previous two series: 808.807 for the LHD variant, and 808.808 for the RHD one.In its third iteration the Appia was finally mature, and 55,577 saloons were made, the vast majority in left hand drive.^[4]

At the end of the 1950s, with third series Appia sales soaring, LanciaCEO Fidanza advocated preparing a fourth series with an all-new body.^[10] Fessia, a strong proponent offront-wheel drive, was reluctant about updating the old design, and moreover one that was Jano's brainchild.^[10] In the end Fessia had the upper hand, as Fidanza had come to grips with the board and resigned.^[11] TheLancia Fulvia was developed and introduced in 1963, a clean-sheet design reprising the longitudinal front-wheel drive layout of Fessia's largerFlavia, but with Lancia's final narrow vee V4 engine.

Appia C83 pick-up

Appia C10 van

Appia C86S ambulance

Starting with 1954 Lancia also built light commercial bodies on the Appia chassis, replacing the analogous versions of the earlierArdea.Three models were offered: the Furgoncinopanel van (chassis code C80 or C80S for left hand drive), Camioncinopick-up (C83 or C83S), and anambulance based on the Furgoncino, the Autolettiga (C86 or C86S). In respect to the saloon, all had shorterfinal drives, lower horsepower engines, widenedaxle tracks, upsized 16-inch wheels and larger tyres—and consequently bodywork altered to accept these modifications.^[12]With the introduction of the second series Appia in 1954 all three models received upgrades similar to the saloon's, while keeping the body style almost untouched. Commercial variants were not upgraded to third series specifications, as during 1959 they were phased out in favour of aforward control full-fledgedvan using Appia drivetrains, theLancia Jolly.^[13]

First series Appias were only offered in factory body styles. This changed with the second and third series Appias, which were also built as aplatform chassis intended for coachbuilt bodies.Towards the end of 1955 a first batch of 14 chassis based on the brand new second series Appia were built and handed over to some of the most prominent coachbuilders of the time:Allemano,Boano,Ghia Aigle,Motto,Pinin Farina,Vignale andZagato.^[15]Initially all fourteen chassis were coded tipo 812.00, based on standard saloon mechanicals; five of were upgraded to a more powerful 53 PS engine and floor-mounted shifter, and given the new type designation 812.01. At the April 1956Turin Motor Show, a month after the successful introduction of the second series Appia inGeneva, five specially bodied Appias were shown: a coupé and a two-door saloon byVignale, a coupé each from Pinin Farina, Boano andZagato.^[6] Between Spring 1956 and Spring 1957 the coachbuilders presented their one-off interpretations of the Appia at various motor shows. Later more 812.01 chassis were built, bringing the total of unique to thirteen.

Of the coachbuilders who had worked on the first fourteen chassis, two were selected by Lancia to produce special Appia body styles:Pinin Farina for the coupé, andVignale for the convertible. Their nearly definitive proposals debuted at the March 1957Geneva Motor Show, and soon went into limited series production. Built by their respective designers on chassis supplied by Lancia, these were included in Lancia's own catalogue and regularly sold through Lancia dealerships. In the later years other variants were added to the official portfolio: Vignale's Lusso, Zagato's GTE and Sport, and Viotti's Giardinetta.All of these variants were built on the 812.01 type chassis with the more powerful engine and floor shifter; when the third series saloon debuted its mechanical upgrades were transferred to the chassis, and the engine gained one horsepower 54 PS.In early 1960 a revised, more powerful engine was adopted, putting out 60 HP thanks to a newWeber carburettor and aninlet manifold with a duct per each cylinder.^[16]In total 5,161 Appia chassis for coachbuilders were made.

Lancia Appia Coupé
Dimensions
Wheelbase	2,510 mm (98.8 in)
Length	4,130 mm (162.6 in)
Width	1,490 mm (58.7 in)
Height	1,310 mm (51.6 in)
Kerb weight	925 kg (2,039 lb)

Pinin Farina built a2+2coupé version between 1957 and 1963.Pinin Farina's first proposal, from the 1956Turin Motor Show, was a 4-seater coupé based on an 812.00 chassis and reminiscent of the Lancia Florida prototype, which Lancia's management did not find satisfactory.^[16] Therefore, Pinin Farina set off to work on a second prototype, a 2+2 on one of the five more powerful 812.01 chassis, shown with Lancia's blessing at the March 1957Geneva Motor Show.^[16]Shortly after the Motor Show the car went into small series production, christened Appia Coupé.The Coupé was characterised by a wide grille—which previewed Pinin Farina's ownLancia Flaminia as well as the third series Appia berlina, by a V-shaped B-pillar parting the side window from the wrap-around rear window, and by a two-tone paint scheme. The tail lights were trapezoidal element inset in the rear fins. Bodies were steel, with afibreglass boot lid.

With the introduction of the third series Appia in 1959 the coupé was updated too, to a slightly stronger 54 engine. Third series coupés can be distinguished by the rear tail lights, grouped in a single unit making up the edge of the rear—more vertical—tail fins.In the spring of 1960 the updated 60 HP engine was adopted.^[16] Later in the production run production was moved toCarrozzeria Viotti. Viotti-built cars were identical to Pinin Farina's, although late ones were based on a reinforced 812.04 chassis and had fibreglass instead of aluminium dashboards, and steel instead of fibreglass boot lids.Production amounted to 302 second series cars all built by Pinin Farina, and some 785 third series cars made by Pinin Farina and Viotti. 1,087 cars were built overall, from 1957 to 1963.

Lancia Appia Convertibile and Lusso
Lancia Appia Convertibile Vignale
Dimensions
Wheelbase	2,510 mm (98.8 in)
Length	Convertibile: 4,150 mm (163.4 in) Lusso: 4,340 mm (170.9 in)
Width	Convertibile: 1,510 mm (59.4 in) Lusso: 1,520 mm (59.8 in)
Height	Convertibile: 1,300 mm (51.2 in) Lusso: 1,395 mm (54.9 in)
Kerb weight	Convertibile: 920 kg (2,028 lb) Lusso: 930 kg (2,050 lb)

Vignale's creations from the 1956Turin Motor Show — on two of the eight 812.00 chassis built — were a coupé named Appia Sport, reminiscent of Vignale's ownLancia Aurelia "Raggio Azzurro", and the Gran Lusso, an elegant 2-door saloon.^[1]

Vignale was then chosen to build acabriolet version of the Appia. TheLancia Appia Convertibile, designed byGiovanni Michelotti, was introduced at the 1957Turin Motor Show and produced up to 1962. Initially a two-seater, it was later revised to accept two rear occasional seats, thus becoming a 2+2 from the summer of 1968.^[6] All Convertibles were built on an 812.01 chassis; at first based on the second series Appia platform with a 53 PS engine, upgraded in 1959 to the third series platform and 54 PS engine, and finally in 1960 to the more powerful 60 PS engine. From 1957 to 1962, 1,584 convertibles were built.^[1]

At the 1958Turin Motor Show,Vignale introduced another special Appia variant, theLancia Appia Lusso orBerlina Lusso.^[15] This was a two-door saloon with frameless doors and ample windows, again with styling by Michelotti derived from the 1956 Lancia Gran Lusso.^[15] All Vignale Lusso were built on a specific version of the Tipo 812.02 chassis, a strengthened series three platform.^[18] Front wings and bonnet were shared with the Convertibile, but the Lusso was longer, larger and taller.^[18] In total 477 Appia Lusso were made in the Vignale factory from 1959 to 1962.^[18][15]

Zagato built four coupé versions based on the Berlina between 1957 and 1962, for a grand total of 721 vehicles. Zagato's creations catered to Lancia's sportiest clientele, who would privately race their cars.^[19] All of Zagato's Appias were bodied stretching analuminium skin over a boxed steel framework.^[19]

The harbinger of all Zagato Appias was the prototype built on a type 812.01 chassis, serial number 1005, and first displayed at the 1956Turin Motor Show. It was immediately nicknamedAppia Cammello, "Camel", because of the double humps it carried not only on the roof—Zagato's signature double bubble—but also on the engine bonnet and boot lid.Originally painted in two-tone blue and white, and fully finished with bumpers and over-riders, this prototype was victorious at that year'sCortinaconcours d'elegance.^[20] Later it was outfitted for racing—applying anamaranto (dark red) livery, removing the bumpers and fitting more conventional looking bonnet and boot lid—and entered at the 1957Mille Miglia.^[20]

During early 1957,Zagato built some 30 more Appias, which remained somewhat similar to the first Cammello, but lost the humps on the bonnet and boot lid, donned thin vertical fins over the rear wings and Plexiglas-covered headlamps, and gained a new grille which would set the template for all future Appia Zagato.^[21] All these cars differed a lot from one another.After this first run of prototypes two models were more or less standardised and built in roughly 150 examples. These were the Appia GT, with open headlights carried over from the saloon, and the same 53 PS engine found on other coachbuilders' models; and the sportier Appia GTS, with faired in headlights, a more streamlined body, often a double bubble roof, and a tuned 60 PS engine. The interior carried over the standard car's steering wheel but added tube-framed leatherette sport seats; on the GTS a wood-rimmed steering wheel and bucket seats were optional.^[21]

At the1957 Mille Miglia three Zagato Appias scored a remarkable 1-2-3 finish in their class: the winner was Luciano Mantovani on a GTS, runner up Enrico Anselmi on another GTS, third the aforementioned Cammello piloted by Giorgio Lurani.^[22]

Lancia Appia GTE
Dimensions
Wheelbase	2,510 mm (98.8 in)
Length	4,190 mm (165.0 in)
Width	1,420 mm (55.9 in)
Height	1,240 mm (48.8 in)
Kerb weight	820 kg (1,808 lb)

At the November 1958Turin Motor Show, the newLancia Appia GTE (standing forGran Turismo Esportazione) was introduced, with deliveries starting in January 1959.^[22]The GTE marked an important change in the relationship betweenZagato and Lancia: it was the first Zagato car to be included in Lancia's price lists and sold by Lancia dealers. For Lancia Zagato went from a buyer of chassis to an official supplier of specially bodied finished cars.First shown to the public at the 1958Turin Motor Show, the first GTEs were delivered in early 1959.GTE bodywork was more low slung and streamlined than its predecessors'. The car had a continuous waistline, without the previous humps over the rear wheels; the nose was longer, and the under elongated Plexiglas covers the headlights were set deeply into the wings. At the rear the tail lights were partially sunken in and crowned by protrusions in the bodywork.

The GTE went through numerous updates.In the Spring 1959 chassis upgraded to third series specifications were phased in.^[22] From the autumn newly enacted Italiantraffic laws prohibited headlights cover. GTEs for Italy and some export countries had open headlights, and modified bodywork setting them further forward.^[22] During 1960 the improved 60 PS engine was adopted. When the Appia Sport was introduced it did not supersede the GTE, but rather some of its features were carried over, such as new headlights and protruding in place of flush pushbutton door handles.^[22] The last GTEs were built on a specific 812.03 chassis; the very last example was completed in April 1962.^[22]It is estimated that total GTE production amounts to 167 with the earlier 53 PS engine, and 134 with the later 60 PS one.^[22]

Lancia Appia Sport
1961 Lancia Appia Sport
Dimensions
Wheelbase	2,350 mm (92.5 in)
Length	3,990 mm (157.1 in)
Width	1,410 mm (55.5 in)
Height	1,230 mm (48.4 in)
Kerb weight	820 kg (1,808 lb)

The last and ultimate of Zagato's Appias was the Appia Sport, built from 1961 to 1963 on a shortwheelbase chassis coded 812.05.^[22] The Sport's premiere took place at the March 1961Geneva Motor Show, and production began concurrently; it did not replace the standard wheelbase GTE, which remained on sale alongside it up to 1962.^[22] At 2,350 mm (92.5 in) the Sport's wheelbase was 160 mm (6.3 in) shorter than the GTE's, resulting in a 200 mm (7.9 in) shorter overall length. Adapting the GTE bodywork to the smaller dimensions was the first job of a youngErcole Spada, just hired at Zagato.^[22] From the front the Sport was similar to an open headlight GTE, but had a much rounder rear end, tail lights fully sunken into the bodywork, and a fastback roofline.The Sport is the only Appia Zagato for which production numbers are certain, as the coachbuilder started keeping detailed registers of its production only in 1960: production began in March 1961 concurrently to the model launch, with chassis #1001, and ended in January 1963 with chassis #1201, the 200th car.^[22] It is also the most standardised of all Zagato Appias, though differences in exterior and interior trim from one car to another were still present, depending on part availability at the time and on the client's desires.

A Lancia Appia Zagato was raced in the1959 12 Hours of Sebring, among the drivers was newsmanWalter Cronkite.^[23]

Towards the end of 1958, Lancia turned toCarrozzeria Viotti to build a 3-doorestate based on the third series Appia.^[12] Named Appia Giardinetta—Viotti's trademark designation for estate cars—the production version was unveiled at the November 1959Turin Motor Show. Chassis was extensively modified, receiving a new 808.21^[12][24] type code: a three-door layout was chosen, adding a centre pillar (the Appia saloon had none) to strengthen the body, and the rear part of the platform was altered to lower the boot opening.^[12] Despite looking very similar, little more than lamps and interior details were carried over from the saloon's bodywork. The body was widened 6 cm (2.4 in), which in turn required a wider dashboard, new bumpers, grille, and windscreen.^[12] Insideleatherette and rubber mats took place of Lancia's traditional wool cloth and carpets; the rear seats folded down forming a completely flat 1.5 m long (4 ft 11 in) loading area.^[12] The complexity of this development and lack ofeconomies of scale reflected on the list price, which was approximately 25% higher than the saloon's.^[12] Due to the additional weight, the manufacturer's claimed top speed for the Giardinetta was down to 120 km/h (75 mph).^[24] In total just 300 Giardinettas were made.

The Appia Berlina usedunibody construction. Front suspension was of Lancia'ssliding pillar type, with hydraulicdampers.At the rear there was asolid axle onleaf springs, with hydraulic dampers; the axle had an aluminium differential housing and a stamped steel structure.All Appias were equipped withhydraulic brakes, anddrums an all four wheels. Series three cars gained a dual braking circuit andtwin leading shoe, finned aluminium front drums with cast iron wear rings; the rears remained solid cast iron.When leaving the factory they would originally fitPirelli Cinturato 155HR15 tyres (CA67).

The Appia had a V4 engine with a 10.14° angle between thecylinder banks and a single head for all four cylinders. All models had abore andstroke of 68 mm × 75 mm (2.7 in × 3.0 in), for a total displacement of 1,089 cc (66.5 cu in).The valvetrain comprised two angledpoppet valves per cylinder, actuated bypushrods and rocker arms; there were two in-blockcamshafts, the left hand one for all exhaust and the right hand one for all intake valves, driven by a chain with hydraulic tensioner.Thecylinder heads werealuminium, as werecrankcase andoil pan, integrated in a single casting; thecylinder block wascast iron.

The transmission was a four-speedgearbox, the top threesynchronised. Theclutch was dry single plate, mechanically actuated.

An S1 Berlina saloon tested by the BritishThe Motor magazine in 1954 had a top speed of 76.1 mph (122.5 km/h) and could accelerate from 0–60 mph (97 km/h) in 32.5 seconds. A fuel consumption of 29.0 miles per imperial gallon (9.7 L/100 km; 24.1 mpg_‑US) was recorded. The car was not at the time available on the UK market but an Italian price of 1,328,600 Lire was reported (converted to £780).^[26]

Notes

Wikimedia Commons has media related toLancia Appia.

• Cub Lancia Appia — Appia information and publications(in Italian)
• Lancia Motor Club (UK)
• Lancia Appia Convertible (Vignale)

• Lancia vehicles
• Cars introduced in 1953
• 1960s cars
• Rear-wheel-drive vehicles
• Sedans
• Station wagons
• Coupés
• Convertibles
• Pininfarina
• Cars discontinued in 1963

• CS1 Italian-language sources (it)
• CS1 French-language sources (fr)
• CS1 maint: ignored ISBN errors
• Articles with short description
• Short description matches Wikidata
• Commons category link from Wikidata
• Articles with Italian-language sources (it)