 The LIGO Livingston control room as it was during Advanced LIGO's first observing run (O1) | |
| Alternative names | LIGO |
|---|---|
| Location(s) | Hanford Site,Washington, andLivingston, Louisiana, US |
| Coordinates | LIGO Hanford Observatory:46°27′19″N119°24′28″W / 46.45528°N 119.40778°W /46.45528; -119.40778 (LIGO Hanford Observatory) LIGO Livingston Observatory:30°33′47″N90°46′28″W / 30.56306°N 90.77444°W /30.56306; -90.77444 (LIGO Livingston Observatory) |
| Wavelength | 43 km (7.0 kHz)–10,000 km (30 Hz) |
| Length | 4,000 m (13,123 ft 4 in) |
| Website | www |
  LIGO Livingston Observatory LIGO Hanford Observatory LIGO observatories in theContiguous United States | |
 Related media on Commons | |
TheLaser Interferometer Gravitational-Wave Observatory (LIGO) is a large-scale physics experiment and observatory designed to detect cosmicgravitational waves and to develop gravitational-wave observations as an astronomical tool.[1] Prior to LIGO, all data about the universe has come in the form of light and other forms ofelectromagnetic radiation, from limited direct exploration on relatively nearbySolar System objects such as theMoon,Mars,Venus,Jupiter and their moons, asteroids etc, and fromhigh energy cosmic particles. Initially, two large observatories were built in the United States with the aim of detecting gravitational waves bylaserinterferometry. Two additional, smaller gravitational wave observatories are now operational in Japan (KAGRA) and Italy (Virgo). The two LIGO observatories use mirrors spaced 4 km apart to measure changes in length—over an effective span of 1120 km—of less than one ten-thousandth thecharge diameter of aproton.[2]
The initial LIGO observatories were funded by the United StatesNational Science Foundation (NSF). They were conceived, built, and are operated byCaltech andMIT.[3][4] They collected data from 2002 to 2010, but no gravitational waves were detected during that period.
The Advanced LIGO Project to enhance the original LIGO detectors began in 2008, and continues to be supported by the NSF, with important contributions from the United Kingdom'sScience and Technology Facilities Council, theMax Planck Society of Germany, and theAustralian Research Council.[5][6] The improved detectors began operation in 2015. The detection of gravitational waves was reported in 2016 by theLIGO Scientific Collaboration (LSC) and theVirgo Collaboration with the international participation of scientists from several universities and research institutions. Scientists involved in the project and the analysis of the data forgravitational-wave astronomy are organized by the LSC, which includes more than 1000 scientists worldwide,[7][8][9] as well as 440,000 activeEinstein@Home users as of December 2016[update].[10]
LIGO is the largest and most ambitious project ever funded by the NSF.[11][12] In 2017, theNobel Prize in Physics was awarded toRainer Weiss,Kip Thorne andBarry Barish "for decisive contributions to the LIGO detector and the observation of gravitational waves".[13]
Observations are made in "runs". As of January 2022[update], LIGO has made three runs (with one of the runs divided into two "subruns"), and made 90detections of gravitational waves.[14][15] Maintenance and upgrades of the detectors are made between runs. The first run, O1, which ran from 12 September 2015 to 19 January 2016, made the first three detections, all black hole mergers. The second run, O2, which ran from 30 November 2016 to 25 August 2017, made eight detections: seven black hole mergers and the firstneutron star merger.[16] The third run, O3, began on 1 April 2019; it was divided into O3a, from 1 April to 30 September 2019, and O3b, from 1 November 2019[17] until it was suspended on 27 March 2020 due toCOVID-19.[18] The O3 run included the first detection of the merger of a neutron star with a black hole.[15]
Subsequent gravitational wave observatoriesVirgo in Italy, andKAGRA in Japan, which both use interferometer arms 3 km long, coordinated with LIGO to continue observations after the COVID-caused stop, and LIGO's O4 observing run started on 24 May 2023.[19][20] LIGO projects a sensitivity goal of 160–190 Mpc for binary neutron star mergers (sensitivities: Virgo 80–115 Mpc, KAGRA greater than 1 Mpc).[21]
The LIGO concept built upon early work by many scientists to test a component ofAlbert Einstein's theory ofgeneral relativity, the existence of gravitational waves. Starting in the 1960s, American scientists includingJoseph Weber, as well as Soviet scientists Mikhail Gertsenshtein and Vladislav Pustovoit, conceived of basic ideas and prototypes of laserinterferometry,[22][23] and in 1967Rainer Weiss ofMIT published an analysis of interferometer use and initiated the construction of a prototype with military funding, but it was terminated before it could become operational.[24] Starting in 1968,Kip Thorne initiated theoretical efforts on gravitational waves and their sources atCaltech, and was convinced that gravitational wave detection would eventually succeed.[22]
Prototype interferometric gravitational wave detectors (interferometers) were built in the late 1960s byRobert L. Forward and colleagues atHughes Research Laboratories (with mirrors mounted on a vibration isolated plate rather than free swinging), and in the 1970s (with free swinging mirrors between which light bounced many times) byWeiss at MIT, and then byHeinz Billing and colleagues inGarching Germany, and then byRonald Drever,James Hough and colleagues in Glasgow, Scotland.[25]
In 1980, the NSF funded the study of a large interferometer led by MIT (Paul Linsay,Peter Saulson, Rainer Weiss), and the following year, Caltech constructed a 40-meter prototype (Ronald Drever and Stan Whitcomb). The MIT study established the feasibility of interferometers at a 1 km scale with adequate sensitivity.[22][26]
Under pressure from the NSF, MIT and Caltech were asked to join forces to lead a LIGO project based on the MIT study and on experimental work at Caltech, MIT, Glasgow, andGarching. Drever, Thorne, and Weiss formed a LIGO steering committee, though they were turned down for funding in 1984 and 1985. By 1986, they were asked to disband the steering committee and a single director,Rochus E. Vogt (Caltech), was appointed. In 1988, a research and development proposal achieved funding.[22][26][27][28][29][30]
From 1989 through 1994, LIGO failed to progress technically and organizationally. Only political efforts continued to acquire funding.[22][31] Ongoing funding was routinely rejected until 1991, when theU.S. Congress agreed to fund LIGO for the first year for $23 million. However, requirements for receiving the funding were not met or approved, and the NSF questioned the technological and organizational basis of the project.[27][28] By 1992, LIGO was restructured with Drever no longer a direct participant.[22][31][32][33] Ongoing project management issues and technical concerns were revealed in NSF reviews of the project, resulting in the withholding of funds until they formally froze spending in 1993.[22][31][34][35]
In 1994, after consultation between relevant NSF personnel, LIGO's scientific leaders, and the presidents of MIT and Caltech, Vogt stepped down andBarry Barish (Caltech) was appointed laboratory director,[22][32][36] and the NSF made clear that LIGO had one last chance for support.[31] Barish's team created a new study, budget, and project plan with a budget exceeding the previous proposals by 40%. Barish proposed to the NSF and National Science Board to build LIGO as an evolutionary detector, where detection of gravitational waves with initial LIGO would be possible, and with advanced LIGO would be probable.[37] This new proposal received NSF funding, Barish was appointedPrincipal Investigator, and the increase was approved. In 1994, with a budget of US$395 million, LIGO stood as the largest overall funded NSF project in history. The project broke ground in Hanford, Washington in late 1994 and in Livingston, Louisiana in 1995. As construction neared completion in 1997, under Barish's leadership two organizational institutions were formed, LIGO Laboratory and LIGO Scientific Collaboration (LSC). The LIGO laboratory consists of the facilities supported by the NSF under LIGO Operation and Advanced R&D; this includes administration of the LIGO detector and test facilities. The LIGO Scientific Collaboration is a forum for organizing technical and scientific research in LIGO. It is a separate organization from LIGO Laboratory with its own oversight. Barish appointed Weiss as the first spokesperson for this scientific collaboration.[22][27]
Initial LIGO operations between 2002 and 2010 did not detect any gravitational waves. In 2004, under Barish, the funding and groundwork were laid for the next phase of LIGO development (called "Enhanced LIGO"). This was followed by a multi-year shut-down while the detectors were replaced by much improved "Advanced LIGO" versions.[38][39] Much of the research and development work for the LIGO/aLIGO machines was based on pioneering work for theGEO600 detector at Hannover, Germany.[40][41] By February 2015, the detectors were brought into engineering mode in both locations.[42]
In mid-September 2015, "the world's largest gravitational-wave facility" completed a five-year US$200-million overhaul, bringing the total cost to $620 million.[9][43] On 18 September 2015, Advanced LIGO began its first formal science observations at about four times the sensitivity of the initial LIGO interferometers.[44] Its sensitivity was to be further enhanced until it was planned to reach design sensitivity around 2021.[update][45][needs update]
On 11 February 2016, the LIGO Scientific Collaboration andVirgo Collaboration published a paper about thedetection of gravitational waves, from a signal detected at 09.51UTC on 14 September 2015 of two ~30solar mass black holes merging about 1.3 billionlight-years from Earth.[46][47]
Current executive directorDavid Reitze announced the findings at a media event in Washington D.C., while executive director emeritus Barry Barish presented the first scientific paper of the findings at CERN to the physics community.[48]
On 2 May 2016, members of theLIGO Scientific Collaboration and other contributors were awarded aSpecial Breakthrough Prize in Fundamental Physics for contributing to the direct detection of gravitational waves.[49]
On 16 June 2016 LIGO announced asecond signal was detected from the merging of two black holes with 14.2 and 7.5 times the mass of the Sun. The signal was picked up on 26 December 2015, at 3:38 UTC.[50]
The detection of a third black hole merger, between objects of 31.2 and 19.4 solar masses, occurred on 4 January 2017 and was announced on 1 June 2017.[51][52]Laura Cadonati was appointed the first deputy spokesperson.[53]
A fourth detection of a black hole merger, between objects of 30.5 and 25.3 solar masses, was observed on 14 August 2017 and was announced on 27 September 2017.[54]
In 2017, Weiss, Barish, and Thorne received theNobel Prize in Physics "for decisive contributions to the LIGO detector and the observation of gravitational waves". Weiss was awarded one-half of the total prize money, and Barish and Thorne each received a one-quarter prize.[55][56][57]
After shutting down for improvements, LIGO resumed operation on 26 March 2019, with Virgo joining the network of gravitational-wave detectors on 1 April 2019.[58] Both ran until 27 March 2020, when theCOVID-19 pandemic halted operations.[18] During the COVID shutdown, LIGO underwent a further upgrade in sensitivity, and observing run O4 with the new sensitivity began on 24 May 2023.[19]
LIGO's mission is to directly observe gravitational waves of cosmic origin. These waves were first predicted by Einstein'sgeneral theory of relativity in 1916, when the technology necessary for their detection did not yet exist. Their existence was indirectly confirmed in 1974, when observations of the binary pulsarPSR 1913+16 showed an orbital decay which matched Einstein's predictions of energy loss by gravitational radiation. The Nobel Prize in Physics 1993 was awarded toHulse andTaylor for this discovery.[60]
Direct detection of gravitational waves had long been sought. Their discovery has launched a new branch of astronomy to complementelectromagnetic telescopes andneutrino observatories.Joseph Weber pioneered the effort to detect gravitational waves in the 1960s through his work onresonant mass bar detectors. Bar detectors continue to be used at six sites worldwide. By the 1970s, scientists includingRainer Weiss realized the applicability of laserinterferometry to gravitational wave measurements.Robert Forward operated an interferometric detector at Hughes in the early 1970s.[61]
In fact as early as the 1960s, and perhaps before that, there were papers published on wave resonance of light and gravitational waves.[62] Work was published in 1971 on methods to exploit this resonance for the detection of high-frequencygravitational waves. In 1962, M. E. Gertsenshtein and V. I. Pustovoit published the very first paper describing the principles for using interferometers for the detection of very long wavelength gravitational waves.[63] The authors argued that by using interferometers the sensitivity can be 107 to 1010 times better than by using electromechanical experiments. Later, in 1965,Braginsky extensively discussed gravitational-wave sources and their possible detection. He pointed out the 1962 paper and mentioned the possibility of detecting gravitational waves if the interferometric technology and measuring techniques improved.
Since the early 1990s, physicists have thought that technology has evolved to the point where detection ofgravitational waves—of significant astrophysical interest—is now possible.[64]
In August 2002, LIGO began its search for cosmic gravitational waves. Measurable emissions of gravitational waves are expected from binary systems (collisions and coalescences ofneutron stars orblack holes),supernova explosions of massive stars (which form neutron stars and black holes), accreting neutron stars, rotations of neutron stars with deformed crusts, and the remnants of gravitational radiation created by thebirth of the universe. The observatory may, in theory, also observe more exotic hypothetical phenomena, such as gravitational waves caused by oscillatingcosmic strings or collidingdomain walls.
LIGO operates two gravitational wave observatories in unison: the LIGO Livingston Observatory (30°33′47″N90°46′28″W / 30.56306°N 90.77444°W /30.56306; -90.77444) inLivingston, Louisiana, and the LIGO Hanford Observatory, on theDOE Hanford Site (46°27′19″N119°24′28″W / 46.45528°N 119.40778°W /46.45528; -119.40778), located nearRichland, Washington. These sites are separated by 3002 km straight line distance through the earth, but 3030 km over the surface. Since gravitational waves are expected to travel at the speed of light, this distance corresponds to a difference in gravitational wave arrival times of up to ten milliseconds. With the difference in arrival times at three different facilities one cantrilaterate the source of the wave.This is done by adding a third instrument likeVirgo, located at an even greater distance, in Europe.[65]
Each observatory supports an L-shapedultra high vacuum system, measuring 4 km on each side. Up to fiveinterferometers can be set up in each vacuum system.
The LIGO Livingston Observatory houses one laserinterferometer in the primary configuration. This interferometer was successfully upgraded in 2004 with an active vibration isolation system based on hydraulic actuators providing a factor of 10 isolation in the 0.1–5 Hz band. Seismic vibration in this band is chiefly due tomicroseismic waves and anthropogenic sources (traffic, logging, etc.).
The LIGO Hanford Observatory houses one interferometer, almost identical to the one at the Livingston Observatory. During the Initial and Enhanced LIGO phases, a half-length interferometer operated in parallel with the main interferometer. For this 2 km interferometer, theFabry–Pérot arm cavities had the same optical finesse, and, thus, half the storage time as the 4 km interferometers. With half the storage time, the theoretical strain sensitivity was as good as the full length interferometers above 200 Hz but only half as good at low frequencies. During the same era, Hanford retained its original passive seismic isolation system due to limited geologic activity in Southeastern Washington.
The parameters in this section refer to theAdvanced LIGO experiment. The primary interferometer consists of two beam lines of 4 km length which form a power-recycledMichelson interferometer withGires–Tournois etalon arms. A pre-stabilized 1064 nmNd:YAG laser emits a beam with a power of 20 W that passes through a power recycling mirror. The mirror fully transmits light incident from the laser and reflects light from the other side increasing the power of the light field between the mirror and the subsequent beam splitter to 700 W. From the beam splitter the light travels along two orthogonal arms. By the use of partially reflecting mirrors,Fabry–Pérot cavities are created in both arms that increase the effective path length of laser light in the arm from 4 km to approximately1200 km.[66] The power of the light field in the cavity is 100 kW.[67]
When a gravitational wave passes through the interferometer, the spacetime in the local area is altered. Depending on the source of the wave and its polarization, this results in an effective change in length of one or both of the cavities. The effective length change between the beams will cause the light currently in the cavity to become very slightly out ofphase (antiphase) with the incoming light. The cavity will therefore periodically get very slightly out ofcoherence and the beams, which are tuned todestructively interfere at the detector, will have a very slight periodically varying detuning. This results in a measurable signal.[68]
After an equivalent of approximately 280 trips down the 4 km length to the far mirrors and back again,[69] the two separate beams leave the arms and recombine at the beam splitter. The beams returning from two arms are kept out of phase so that when the arms are both in coherence and interference (as when there is no gravitational wave passing through), their light waves subtract, and no light should arrive at thephotodiode. When a gravitational wave passes through the interferometer, the distances along the arms of the interferometer are shortened and lengthened, causing the beams to become slightly less out of phase. This results in the beams coming in phase, creating aresonance, hence some light arrives at the photodiode and indicates a signal. Light that does not contain a signal is returned to the interferometer using a power recycling mirror, thus increasing the power of the light in the arms.
Since the signal being measured is so small, the LIGO project has carefully measured, documented, and eliminated many forms of noise. Mechanical/seismic noise sources can move objects in the optical system, such as the mirrors, the photon injectors, etc. Electric and magnetic noise can vibrate the permanent magnets and electronics, and radio waves can couple to electronics in the interferometer controls. These noises may drown out the real signal, or produce spurious signals. Background noise and unknown errors (which happen daily) are in the order of 10−20, while gravitational wave signals are around 10−22. After noise reduction, asignal-to-noise ratio around 20 can be achieved, or higher when combined with other gravitational wave detectors around the world.[70]
Much complexity in the instrument is in reducing these spurious couplings, and in monitoring the environment to detect previously unknown sources of noise in order to mitigate them or estimate their impact on the gravitational wave data[71]. Other than careful insulation of the equipment, the methods of mitigation also include:
Seismic vibration is a major source of noise, mitigated by seismic insulation, as well as by sensitive recording of seismic activity in the vicinity of the site, which allows the effect of seismic activity to be subtracted away from the signal.Earth tides produce significant but highly predictable stretching of the equipment, which is cancelled out by a system which adjusts the position of the chambers or the laser frequency, based on the predicted stretching. There are also many "microseismic" sources that produce ground vibrations, including ocean storms, dam operations, forest logging, trucks driving on a road 2 km away, walking heavily in a control room, etc. When under a strong wind, the walls of the building can tilt, which deforms the floor within 10 m of the walls, creating "tilt noise". Even thethermal expansion and contraction of the building itself creates creaks and thumps. Similarly, acoustic vibrations can shake the equipment. This includes wind, nearby vehicles,propeller aircraft,HVAC of a building 300 m away,cooling fans, etc.[72][73][74][75] Other sources of noise include a case of ravens pecking on frost-covered pipes connected to aLN2 cryopump on hot days.[76] Some noises are transient with no identifiable cause.[77]
Electromagnetic noise can couple with electronic and magnetic equipment. Such examples include building heaters, large motors, lights or relatively near-by high-voltage power lines up to 4 km away from the site.[72] SinceBarkhausen noise is suspected to be relevant, magnets at noise-critical locations of aLIGO are made ofsamarium cobalt, which has lower Barkhausen noise.[78]
Because gravity cannot be shielded, the motion of massive objects can create varying gravitational attraction on the test masses in LIGO, calledgravity gradient noise orNewtonian noise. This can be caused by air and soil density variation. Even the gravitational effect of a single human walking within 5 m of the mirror already approaches the noise floor, and the LIGO corner building was designed to keep people at least 10 m from all test masses during normal operations.[79] Cosmic ray events may also create noise in the detector.[75]
Based on current models of astronomical events, and the predictions of thegeneral theory of relativity,[80][81][82] gravitational waves that originate tens of millions of light years from Earth are expected to distort the 4 km mirror spacing by about10−18 m, less than one-thousandth thecharge diameter of aproton. Equivalently, this is a relative change in distance of approximately10−21. A typical event which might cause a detection event would be the late stage inspiral and merger of two 10-solar-mass black holes, not necessarily located in the Milky Way galaxy, which is expected to result in a very specific sequence of signals often summarized by the sloganchirp,burst,quasi-normal mode ringing,exponential decay.
In their fourth Science Run at the end of 2004, the LIGO detectors demonstrated sensitivities in measuring these displacements to within a factor of two of their design.
During LIGO's fifth Science Run in November 2005, sensitivity reached the primary design specification of a detectable strain of 10−21 over a100 Hz bandwidth. The baseline inspiral of two roughly solar-mass neutron stars is typically expected to be observable if it occurs within about 8 millionparsecs (26×10^6 ly), or the vicinity of theLocal Group, averaged over all directions and polarizations. Also at this time, LIGO andGEO 600 (the German-UK interferometric detector) began a joint science run, during which they collected data for several months.Virgo (the French-Italian interferometric detector) joined in May 2007. The fifth science run ended in 2007, after extensive analysis of data from this run did not uncover any unambiguous detection events.
In February 2007, GRB 070201, a shortgamma-ray burst arrived at Earth from the direction of theAndromeda Galaxy. The prevailing explanation of most short gamma-ray bursts is the merger of a neutron star with either a neutron star or a black hole. LIGO reported a non-detection for GRB 070201, ruling out a merger at the distance of Andromeda with high confidence. Such a constraint was predicated on LIGO eventually demonstrating a direct detection of gravitational waves.[83]
After the completion of Science Run 5, initial LIGO was upgraded with certain technologies, planned for Advanced LIGO but available and able to be retrofitted to initial LIGO, which resulted in an improved-performance configuration dubbed Enhanced LIGO.[84] Some of the improvements in Enhanced LIGO included:
Science Run 6 (S6) began in July 2009 with the enhanced configurations on the 4 km detectors.[85] It concluded in October 2010, and the disassembly of the original detectors began.
After 2010, LIGO went offline for several years for a major upgrade, installing the new Advanced LIGO detectors in the LIGO Observatory infrastructures.
The project continued to attract new members, with theAustralian National University andUniversity of Adelaide contributing to Advanced LIGO, and by the time the LIGO Laboratory started the first observing run 'O1' with the Advanced LIGO detectors in September 2015, the LIGO Scientific Collaboration included more than 900 scientists worldwide.[9]
The first observing run operated at a sensitivity roughly three times greater than Initial LIGO,[87] and a much greater sensitivity for larger systems with their peak radiation at lower audio frequencies.[88]
On 11 February 2016, the LIGO andVirgo collaborations announced thefirst observation of gravitational waves.[47][67] The signal, namedGW150914,[67][89] was recorded on 14 September 2015, just two days after Advanced LIGO started collecting data following the upgrade.[47][90][91] It matched thepredictions of general relativity[80][81][82] for the inward spiral andmerger of apair ofblack holes and subsequent ringdown of the resulting single black hole. The observations demonstrated the existence of binary stellar-mass black hole systems and the first observation of a binary black hole merger.
On 15 June 2016, LIGO announced the detection of a second gravitational wave event, recorded on 26 December 2015, at 3:38 UTC. Analysis of the observed signal indicated that the event was caused by the merger of two black holes with masses of 14.2 and 7.5 solar masses, at a distance of 1.4 billion light years.[50] The signal was namedGW151226.[92]
The second observing run (O2) ran from 30 November 2016[93] to 25 August 2017,[94] with Livingston achieving 15–25% sensitivity improvement over O1, and with Hanford's sensitivity similar to O1.[95] In this period, LIGO saw several further gravitational wave events:GW170104 in January;GW170608 in June; andfive others between July and August 2017. Several of these were also detected by the Virgo Collaboration.[96][97][98] Unlike the black hole mergers which are only detectable gravitationally,GW170817 came from thecollision of two neutron stars and was also detected electromagnetically by gamma ray satellites and optical telescopes.[97]
The third run (O3) began on 1 April 2019[99] and was planned to last until 30 April 2020; in fact it was suspended in March 2020 due toCOVID-19.[18][100][101] On 6 January 2020, LIGO announced the detection of what appeared to be gravitational ripples from a collision of two neutron stars, recorded on 25 April 2019, by the LIGO Livingston detector. Unlike GW170817, this event did not result in any light being detected. Furthermore, this is the first published event for a single-observatory detection, given that the LIGO Hanford detector was temporarily offline at the time and the event was too faint to be visible in Virgo's data.[102]
The fourth observing run (O4) was planned to start in December 2022,[103] but was postponed until 24 May 2023. O4 is projected to continue until February 2025.[19] As of O4, the interferometers are operating at a sensitivity of155–175 Mpc,[19] within the design sensitivity range of160–190 Mpc for binary neutron star events.[104]
The fifth observing run (O5) is projected to begin in late 2025 or in 2026.[19]
LIGO-India, or INDIGO, is a planned collaborative project between the LIGO Laboratory and the Indian Initiative in Gravitational-wave Observations (IndIGO) to create a gravitational-wave detector in India. The LIGO Laboratory, in collaboration with theUS National Science Foundation and Advanced LIGO partners from the U.K., Germany and Australia, has offered to provide all of the designs and hardware for one of the three planned Advanced LIGO detectors to be installed, commissioned, and operated by an Indian team of scientists in a facility to be built in India.
The LIGO-India project is a collaboration between LIGO Laboratory and the LIGO-India consortium: Institute of Plasma Research, Gandhinagar; IUCAA (Inter-University Centre for Astronomy and Astrophysics), Pune and Raja Ramanna Centre for Advanced Technology, Indore.
The expansion of worldwide activities in gravitational-wave detection to produce an effective global network has been a goal of LIGO for many years. In 2010, a developmental roadmap[105] issued by theGravitational Wave International Committee (GWIC) recommended that an expansion of the global array of interferometric detectors be pursued as a highest priority. Such a network would afford astrophysicists with more robust search capabilities and higher scientific yields. The current agreement between the LIGO Scientific Collaboration and the Virgo collaboration links three detectors of comparable sensitivity and forms the core of this international network. Studies indicate that the localization of sources by a network that includes a detector in India would provide significant improvements.[106][107] Improvements in localization averages are predicted to be approximately an order of magnitude, with substantially larger improvements in certain regions of the sky.
TheNSF was willing to permit this relocation, and its consequent schedule delays, as long as it did not increase the LIGO budget. Thus, all costs required to build a laboratory equivalent to the LIGO sites to house the detector would have to be borne by the host country.[108] The first potential distant location was atAIGO inWestern Australia,[109] however the Australian government was unwilling to commit funding by 1 October 2011 deadline.
A location in India was discussed at a Joint Commission meeting between India and the US in June 2012.[110] In parallel, the proposal was evaluated by LIGO's funding agency, the NSF. As the basis of the LIGO-India project entails the transfer of one of LIGO's detectors to India, the plan would affect work and scheduling on the Advanced LIGO upgrades already underway. In August 2012, the U.S. National Science Board approved the LIGO Laboratory's request to modify the scope of Advanced LIGO by not installing the Hanford "H2" interferometer, and to prepare it instead for storage in anticipation of sending it to LIGO-India.[111] In India, the project was presented to theDepartment of Atomic Energy and theDepartment of Science and Technology for approval and funding. On 17 February 2016, less than a week after LIGO's landmark announcement about the detection of gravitational waves, Indian Prime MinisterNarendra Modi announced that the Cabinet has granted 'in-principle' approval to the LIGO-India mega science proposal.[112]
A site near pilgrimage site ofAundha Nagnath in theHingoli district of stateMaharashtra inwestern India has been selected.[113][114]
On 7 April 2023, the LIGO-India project was approved by the Cabinet of Government of India. Construction is to begin in Maharashtra's Hingoli district at a cost of INR 2600crores.[115]
Like Enhanced LIGO, certain improvements will be retrofitted to the existing Advanced LIGO instrument. These are referred to asA+ proposals, and are planned for installation starting from 2019 until the upgraded detector is operational in 2024.[116] The changes would almost double Advanced LIGO's sensitivity,[117][118] and increase the volume of space searched by a factor of seven.[119] The upgrades include:
Because the final LIGO output photodetector is sensitive to phase, and not amplitude, it is possible to squeeze the signal so there is lessphase noise and more amplitude noise, without violating thequantum mechanical limit on their product.[122] This is done by injecting a "squeezed vacuum state" into the dark port (interferometer output) which is quieter, in the relevant parameter, than simple darkness. Such a squeezing upgrade was installed at both LIGO sites prior to the third observing run.[123] The A+ improvement will see the installation of an additionaloptical cavity that acts to rotate the squeezing quadrature from phase-squeezed at high frequencies (above 50 Hz) to amplitude-squeezed at low frequencies, thereby also mitigating low-frequencyradiation pressure noise.
A third-generation detector at the existing LIGO sites is being planned under the name "LIGO Voyager" to improve the sensitivity by an additional factor of two, and halve the low-frequency cutoff to 10 Hz.[124] Plans call for the glass mirrors and1064 nm lasers to be replaced by even larger 160 kg silicon test masses, cooled to 123 K (a temperature achievable withliquid nitrogen), and a change to a longer laser wavelength in the range 1500–2200 nm at which silicon is transparent. (Many documents assume a wavelength of 1550 nm, but this is not final.)
Voyager would be an upgrade to A+, to be operational around 2027–2028.[125]
A design for two larger observatories with longer arms is called "Cosmic Explorer". This is based on the LIGO Voyager technology, including a similar LIGO-type L-shape geometry, but with 20 and 40 km arms. It is currently planned to be on the surface. It has a higher sensitivity thanEinstein Telescope for frequencies beyond 10 Hz, but lower sensitivity under 10 Hz.[124]
This is equivalent to measuring the distance from Earth to the nearest star to an accuracy smaller than the width of a human hair!(that is, toProxima Centauri at4.0208×1013 km).
LIGO's advanced detectors are already three times more sensitive than Initial LIGO was by the end of its observational lifetime
the start of O3 is currently projected to begin in early 2019. Updates will be provided once the installation phase is complete and the commissioning phase has begun. An update on the engineering run prior to O3 will be provided by late summer 2018.
The bottom line is that [the sensitivity] is better than it was at the beginning of O1; we expect to get more detections.
{{cite book}}: CS1 maint: multiple names: authors list (link)
| International | |
|---|---|
| National | |
