| F 13 | |
|---|---|
.jpg) Junkers F 13 over the Aérodrome de Cerny-La-Ferté-Alais | |
| General information | |
| Type | passenger transport |
| Manufacturer | Junkers |
| Designer | Otto Reuter |
| Primary users | Junkers Luftverkehr |
| Number built | 322 |
| History | |
| Manufactured | 1919–1932/2009-2019 |
| Introduction date | 1920 |
| First flight | 25 June 1919[1] |
| Retired | late 1930s (1951 in Brazil) |
TheJunkers F 13 is the world's first all-metal transport aircraft, designed and produced by theGerman aircraft manufacturerJunkers.
Produced shortly after the end of theFirst World War, it was acantilever-wingmonoplane with enclosed accommodation for four passengers and a two seat open cockpit. Like all Junkers duralumin-structured designs, from the 1918J 7 to the 1932Ju 46, (some 35 models), it has analuminium alloy (duralumin) structure entirely covered with Junkers' characteristic corrugated andstressed duralumin skin. Internally, the wing was built up on nine circular cross-section duraluminspars with transverse bracing. All control surfaces werehorn balanced.
A total of 322 aircraft were manufactured, a considerably large number for a commercial airliner of the era, and were operated all over the world. It accounted for over a third of air traffic in the early 1920s. It remained in production for thirteen years and in commercial service for more than thirty. There were many versions including floatplanes for water landing, skis, mailplane, and different engines. Several survive in various states of repair in museums, and a replica of the type was put back in production in the 2010s, taking flight once again nearly a century after the type first flew.
What would become the F 13 originated in the work of ProfessorHugo Junkers and his Research Institute inDessau, Germany throughout the 1910s. These efforts were responsible for producing multiple new ideas pertaining not only toaerodynamics but also the employment and working of lightweight metal construction in aviation.[2]
The F 13[3] was a very advanced aircraft when built, an aerodynamically clean all-metal low-wing cantilever monoplane. It was the world's first all-metal passenger aircraft and Junkers' first commercial aircraft. The designation letter F stood forFlugzeug (aircraft); it was the first Junkers aeroplane to use this system. Earlier Junkers notation labelled it J 13. Russian-built aircraft used the designation Ju 13.[citation needed]
The F 13 first flew on 25 June 1919,[4] powered by a 127 kW (170 hp)Mercedes D.IIIa inline upright water-cooled engine. The first production machines had a wing of greater span and area and was furnished with the more powerful 140 kW (185 hp) BMW IIIa upright inline water-cooled motor.
Many variants[5] were built using Mercedes, BMW, Junkers, andArmstrong SiddeleyPuma liquid-cooledinline engines, andGnome-Rhône Jupiter andPratt & Whitney Hornet air-cooledradial engines. The variants were mostly distinguished by a two letter code, the first letter signifying theairframe and the second the engine. Junkers L5-engined variants all had the second letter -e, so type -fe was the long fuselage -f airframe with a L5 engine.
The F13 was the basis for developing theJunkers W 33 andJunkers W 34.[6]
The Junkers F 13 was an all-metal transport aircraft; its construction and several of its design features, such as itscantilever wing, were particularly noteworthy for the era. Unlike traditional wings of the era, which had to use externalstruts and guywires out of necessity, the wing of the F 13 lacked any stay-wires; their elimination meant that a major source ofdrag was entirely avoided.[2] Instead of exposing the supporting elements to the external air currents, all of the bracing was located within the wing itself, thus providing a neater solution from an aerodynamic perspective. As a consequence of this arrangement, the profile of the wing had to be considerable thicker to accommodate these supporting members; while orthodox attitudes of the era favoured thin profiles, the aerodynamic qualities of the F 13 was quite favourable, largely as a result of diligent experimentation.[2] Another advantage was that, while the polar curve for thin profile wings typically had a relatively restricted range of application, such as for high-speed flight or a rapid rate of climb, of a higher climb, the polar curve of thicker profile wings could perform more adequately across both circumstances.[7]
In terms of its material composition, the F 13 had intentionally discarded traditional materials, such as wood andfabric, in favour of an all-metal approach that had been pioneered by Junkers.[8] This switch eliminated concerns over the variable quality of available wood, and the procurement difficulties in obtaining high quality wood that would be well-suited for aeronautical purposes. It also dispensed with various other concerns, as it was perceived as more difficult to maintain the calibrated dimensions of wood due towarping, the same factor also hindered interchangeability; metal posed less of a fire hazard as well.[9] Unlike Junker's early metal aircraft, which was composed ofsteel and thus quite heavy, the F 13 was made ofduralumin, a light-weightalloy that would find widespread use in aeronautical circles. This metal has greater uniform strength to the aircraft, which made it easier to design; greater ease of calculation increased the economics of this choice as well.[10]
Somewhat offsetting the difficulties of developing a new arrangement to permit the installation of all supporting framework internally, the use of metal enabled a substantial number of new construction features to be adopted.[11] Although the specific gravity of duralumin is greater than that of wood, the weight of the Junkers F 13 was beneath that of all other airplanes, wood or metal, of the same class, as a result of thorough aerodynamic studies conducted by the company.[12] Furthermore, it was also felt that the metal approach would increase structural safety and serviceability.[13] In comparison to its wooden contemporaries, the F 13's all-metal approach was slower tofatigue; it was also less expensive to protect againsthumidity and most other atmospheric conditions.Termites were unable to damage metal aircraft.[11] It was partially for this reason that use of the F 13 in varioustropical countries, particularly those inSouth America, quickly became commonplace. In general, the life of a metal aircraft was believed to be far greater than that of a wooden one.[11]
The supporting surface, which was the basis of the structure, comprises three parts, in order to facilitate transportation.[14] The outer portions of the wings were secured to the framework of the central wing section, whose spars consisted of nine duralumin tubes, in a manner that assured symmetry of the wings. These wings could be mounted and demounted by two men within a few minutes. A cantilever girder comprised the core of the wing's framework.[14] The external metal covering, which wascorrugated for increased strength, helped to withstand the stress oftorsion while the overall structure was fairly resistant to dynamic overloading. In another departure from conventional practices of the time, the fuselage was placed on the wing; this permitted the framework of the wing's central section to form the base of both the fuselage and the cabin.[14] Accordingly, the aircraft had a relatively strong superstructure while also reducing its weight. One advantage of the position of the wing was that it afforded the best possible protection to the cabin and its occupants, in the event of a rough or emergency landing.[14]
The flight controls were fairly conventional, both theelevator andailerons were actuated by the pilot via a column with a wheel while therudder was operated using pedals.[15] Various sliding doors were present for inspection and serviceability purposes for the various control cables, levers, and tubes. Provision was made for the installation of dual flight controls, a feature that was thought to be of particular importance during long-range flights.[16] All of the tail surfaces had fairly large areas that benefitted not only the aircraft's manoeuvrability but also its steadiness in flight. Another departure from convention was the means of adjusting the stabilizer to compensate for weight variations; atrimming tank positioned near the rear of the fuselage could offset nose-heaviness or tail-heaviness by means of a pump controlled by the pilot that would withdraw or add sufficient fuel to achieve equilibrium.[16]
Theundercarriage was largely composed of steel tubing; a total of fourstreamlined supports functioned as spring struts.[16] A V-shaped strut arrangement assured sufficient rigidity while the distance between the wheels was thought to be sufficient to prevent the aircraft turning over even during an oblique landing. The tail skid was both jointed andshock-absorbing; it could be readily replaced and was sizable enough to protect the fuselage from sustaining serious damage. Furthermore, special connections were present for the installation offloats, which could be rapidly substituted for the wheels, to convert the F 13 into afloatplane.[17] These floats, which were made of duralumin, were each internally divided into six tight compartments. The aircraft could be similarly equipped for taking off or landing upon snow or ice via the removal of the wheels and substituting them for duralumin runners while a shoe would be attached to the tail skid.[17]
The aerodynamic efficiency of the F 13 meant that less engine power than had been anticipated could be used; various engines from a variety of suppliers could be installed.[18] Easy access to all points of the engine was possible while various components could be exchanged within a short timeframe. The frontalradiator was specially designed by Junkers to possess a high level of efficiency as well as being relatively lightweight; the pilot was able to regulate the engine temperature via the adjustable shutters.[19] Those aircraft intended for use in a tropical country were typically provided with an additional radiator. Considerable attention was paid to the development of propellers, which was shaped by extensive research into aspects such as the pitch, blade section and diameter. The initial propellers used were composed oflaminated wood that was protected by metal along theirleading edges and achieved a mechanical efficiency at least equal to that of wooden ones.[20] Junkers also worked on metal propellers of its own make, the hollow sections of which diminishes in line with the laws of bodies of uniform resistance. Advantages presented by metal propellers include the ability to replace a single blade (instead of the whole propeller), a lack of sensitivity to climate influences, and the potential to shape the propeller hub to vary the propeller pitch for either speed or climb.[20]
Behind the single engine was a semi-enclosedcockpit for the crew, roofed but without side glazing. There was an enclosed and heated cabin completed with both with windows and doors. Passenger seats were fitted withseat belt[broken anchor]s, unusual for the time. The F 13 has a fixed conventional splitlanding gear with a rear skid, though some variants were fitted with floats or on skis. The cabin was relatively sizable and elegantly furnished for the era; in addition to the four passengers it accommodated, room for another passenger or crew member was present alongside the pilot.[21]
Any manufacturer of civil aircraft immediately afterWorld War I was faced with competition from the very large numbers of surplus warplanes that might be cheaply converted – for example, theDH.9C. German manufacturers had further problems with the restrictions imposed by the Inter-Allied Aeronautical Commission of Control, which banned the production of warplanes and of any aircraft in the period of 1921-22. Junkers[22] picked up orders abroad in 1919 in Austria, Poland and the USA and, in the following years withSCADTA (Colombia) and theUnited States Post Office Department. John Larsen Aircraft in the USA purchased a production licence, their machines being designated JL-6. In 1922 there were sales in England, France Italy and Japan.
The F13 was a very popular civilian aircraft, carrying it is estimated 40% of the world's air traffic in the early 1920s.[6]
In Bolivia,LAB's first airplane was a Junkers F 13; first flight took off fromCochabamba on September 23, 1925.
Junkers set up its own airline –Junkers Luftverkehr AG in 1921 to encourage the acquisition of the F 13 by German airlines and was flying 60 of them by 1923. It also established a branch of the airline in Iran. Other marketing techniques were used, providing F 13s on cheap leases and free loans, with such effect that some 16 operators across Europe were flying them. When Junkers Luftverkehr merged intoLuft Hansa in 1926, 9.5 million miles had been flown by them.Luft Hansa itself bought 55 aircraft and in 1928 waa using them on 43 domestic routes. Even in 1937, its F 13s were flying over 50 flights per week on four routes. They were finally withdrawn in 1938.
Most of the F 13s produced before production ended in 1932 were built at Junkers German base atDessau. During the difficult 1921–23 period production was transferred to Junkers plants atDanzig andReval. In 1922–23,Hugo Junkers signed a contract with theSoviet Union to produce the aircraft in a Soviet factory atFili near Moscow, which became known as "Plant no. 22". Some of these aircraft served Soviet airlines while others were used by theRed Army.
There were some other military users. TheColombian Air Force used the F 13 (and the related W.33, W.34 and K.43) as bombers[citation needed] in theColombia–Peru War in 1932–23. TheRepublic of China flew F 13s converted intoscoutbombers until theJanuary 28 Incident in 1932, when they were destroyed by theJapanese along with the Shanghai Aircraft Factory. The Turkish Flying Forces flew a few.
A feature that made the F 13 popular internationally was the ease with which its landing gear could be converted tofloats. During the formative years of commercial aviation, bodies of water such as rivers, lakes, seas and oceans were more abundant than landing strips and civil airports in many parts of the world, soseaplanes were commonplace and even, in some places, more useful than regular aircraft. Aside from the obvious addition of floats, little modification was needed for this conversion; however, the different configuration could cause issues with directional control,[citation needed] and so some models had theirrudder extended to compensate for this.
From their introduction in 1919 F 13s were in service for more than thirty years; the last commercial F 13 was retired inBrazil in 1951.
.jpg)
.jpg)
A German-Swiss project to build a reconstruction of the F 13 was launched in 2009; the first flight was in September 2016. The reconstruction is equipped with radio and a transponder, and uses a 1930sPratt & Whitney R-985 Wasp Junior engine, but is otherwise as close as possible to the original. Additional reconstructions are to be sold for $2.5 million each.[23]
Junkers Flugzeugwerke (SD303) has resurrected the Junkers F 13 as an all-new airplane to honor Hugo Junkers’ achievements. The company completed the aircraft in 2016 and it is at EBACE commemorating the type's maiden flight 100 years ago. The model is available for purchase, and three others like it are currently under construction. Work was in progress on the second and third aircraft during 2019, with airframe number two's maiden flight planned for early that summer.[24]
The replica F 13 made its maiden flight on 15 September 2016, the culmination of many of years of work on the part of supporters of the project. .[25] The replica was created from original blueprints and also a laser scan of the type at the Museum of Air and Space at Le Bourget, Paris. The replica has 2600 parts and tens of thousands of rivets and is powered by a Wasp radial engine.[25]
.jpg)
Emirate of Afghanistan (
Kingdom of Afghanistan after 1926)
.jpg)
.jpg)
There are five surviving F 13 airframes, all in museums.[6]
Data fromHugo Junkers Pionier der Luftfahrt - Seine Flugzeuge,[42]Junkers: an aircraft album No.3[43]
General characteristics
Performance
| International | |
|---|---|
| National | |
