Harpsichord with double keyboard. The inside of the lid is decorated with two original paintings depicting the battle between Apollo and Pan based onThe Judgment of Midas byHendrick Goltzius (1590). The front cover shows Apollo and the Muses on Mount Helicon. The exterior was repainted with red chinoiserie decoration in the 18th century.
Aharpsichord[a] is amusical instrument played by means of akeyboard. Depressing a key raises its back end within the instrument, which in turn raises a mechanism with a smallplectrum made from quill or plastic that plucks one or more strings. The strings are under tension on asoundboard, which is mounted in a wooden case; the soundboard amplifies the vibrations from the strings so that the listeners can hear it. Like apipe organ, a harpsichord may have more than one keyboardmanual[b] and even apedal board. Harpsichords may also havestop levers which add or remove additional octaves. Some harpsichords may have a buff stop, which brings a strip of buff leather or other material in contact with the strings, muting their sound to simulate the sound of a pluckedlute.[1]
The term denotes the whole family of similar plucked-keyboard instruments, including the smallervirginals,muselar, andspinet. The harpsichord was widely used inRenaissance andBaroque music, both as anaccompaniment instrument and as a soloing instrument. During the Baroque era, the harpsichord was a standard part of thecontinuo group. The basso continuo part acted as the foundation for many musical pieces in this era. During the late 18th century, with the development of thefortepiano (and then the increasing use of thepiano in the 19th century) the harpsichord gradually disappeared from the musical scene (except in opera, where it continued to be used to accompanyrecitative). In the 20th century, it made a resurgence, being used inhistorically informed performances of older music, in new compositions, and, in rare cases, in certain styles of popular music (e.g.,Baroque pop).
The harpsichord was most likely invented in the late Middle Ages. By the 16th century, harpsichord makers in Italy were making lightweight instruments with low tension brass stringing. A different approach was taken in theSouthern Netherlands starting in the late 16th century, notably by theRuckers family. Their harpsichords used a heavier construction and produced a more powerful and distinctive tone with higher tension steel treble stringing. These included the first harpsichords with two keyboards, used fortransposition.[2]
The Flemish instruments served as the model for 18th-century harpsichord construction in other nations. In France, the double keyboards were adapted to control different choirs of strings, making a more musically flexible instrument (so-called 'expressive doubles'). Instruments from the peak of the French tradition, by makers such as theBlanchet family andPascal Taskin, are among the most widely admired of all harpsichords, and are frequently used as models for the construction of modern instruments. In England, theKirkman andShudi firms produced sophisticated harpsichords of great power and sonority. German builders such asHieronymus Albrecht Hass extended the sound repertoire of the instrument by addingsixteen-foot andtwo-foot choirs; these instruments have recently served as models for modern builders.[2]
Around the year 1700 the firstfortepiano was built byBartolomeo Cristofori.[3] The earlyfortepiano uses percussion, the strings being struck with leathered paper hammers instead of being plucked. Unlike the harpsichord, the fortepiano is capable of changes in dynamic volume, giving it its name.[4] By the late 18th century the harpsichord was supplanted by the piano and almost disappeared from view for most of the 19th century: an exception was its continued use in opera for accompanyingrecitative, but the piano sometimes displaced it even there.
Twentieth-century efforts to revive the harpsichord began with instruments that used piano technology, with heavy strings and metal frames. Starting in the middle of the 20th century, ideas about harpsichord making underwent a major change, when builders such asFrank Hubbard,William Dowd, andMartin Skowroneck sought to re-establish the building traditions of the Baroque period. Harpsichords of this type of historically informed building practice dominate the current scene.
Harpsichords vary in size and shape, but all have the same basic mechanism. The player depresses a key that rocks over a pivot in the middle of its length. The other end of the key lifts a jack (a long strip of wood) that holds a smallplectrum (a wedge-shaped piece ofquill, often made of plastic in the 21st century), which plucks the string. When the player releases the key, the far end returns to its rest position, and the jack falls back; the plectrum, mounted on a tongue mechanism that can swivel backwards away from the string, passes the string without plucking it again. As the key reaches its rest position, a felt damper atop the jack stops the string's vibrations. These basic principles are explained in detail below.
Figure 1: schematic view of a 2 × 8' single manual harpsichord
Thekeylever is a simple pivot, which rocks on abalance pin that passes through a hole drilled through the keylever.
Thejack is a thin, rectangular piece of wood that sits upright on the end of the keylever. The jacks are held in place by theregisters. These are two long strips of wood (the upper movable, the lower fixed), which run in the gap between pinblock and bellyrail. The registers have rectangular mortises (holes) through which the jacks pass as they can move up and down. The registers hold the jacks in the precise location needed to pluck the string. Figure 2: upper part of a jack
In the jack, aplectrum juts out almost horizontally (normally the plectrum is angled upwards a tiny amount) and passes just under the string. Historically, plectra were made of bird quill or leather; many modern harpsichords have plastic (delrin orcelcon) plectra.
When the front of the key is pressed, the back of the key rises, the jack is lifted, and the plectrum plucks the string.
The vertical motion of the jack is then stopped by thejackrail (also called theupper rail), which is covered with soft felt to muffle the impact. Figure 3: how the harpsichord action works
When the key is released, the jack falls back down under its own weight, and the plectrum passes back under the string. This is made possible by having the plectrum held in a tongue attached with a pivot and a spring to the body of the jack. The bottom surface of the plectrum is cut at a slant; thus when the descending plectrum touches the string from above, the angled lower surface provides enough force to push the tongue backward.[5]
When the jack arrives in fully lowered position, the felt damper touches the string, causing the note to cease.
Sound board of a harpsichord withChladni patternsDetail of the harpsichord by Karl Conrad Fleischer; Hamburg, 1720 inMuseu de la Música de Barcelona. A decorative rose descends below the soundboard in which it is mounted; the soundboard itself is adorned with floral painting around the rose. The bridge is at lower right.
Each string is wound around atuning pin (also known as awrest pin) at the end nearest the player. When rotated with a wrench or tuning hammer, the tuning pin adjusts the tension so that the string sounds the correct pitch. Tuning pins are held tightly in holes drilled in thepinblock orwrestplank, an oblong hardwood plank. Proceeding from the tuning pin, a string next passes over thenut, a sharp edge that is made of hardwood and is normally attached to the wrestplank. The section of the string beyond the nut forms itsvibrating length, which is plucked and creates sound.
At the other end of its vibrating length, the string passes over thebridge, another sharp edge made ofhardwood. As with the nut, the horizontal position of the string along the bridge is determined by a vertical metal pin inserted into the bridge, against which the string rests. The bridge itself rests on asoundboard, a thin panel of wood usually made ofspruce,fir or—in some Italian harpsichords—cypress. The soundboard efficiently transmits the vibrations of the strings into vibrations in the air; without a soundboard, the strings would produce only a very feeble sound. A string is attached at its far end by a loop to ahitchpin that secures it to the case.
While many harpsichords have one string per note, more elaborate harpsichords can have two or more strings for each note. When there are multiple strings for each note, these additional strings are called "choirs" of strings. This provides two advantages: the ability to vary volume and ability to vary tonal quality. Volume is increased when the mechanism of the instrument is set up by the player (see below) so that the press of a single key plucks more than one string. Tonal quality can be varied in two ways. First, different choirs of strings can be designed to have distinct tonal qualities, usually by having one set of strings plucked closer to the nut, which emphasizes the higherharmonics, and produces a "nasal" sound quality. The mechanism of the instrument, called "stops" (following the use of the term inpipe organs) permits the player to select one choir or the other. Second, having one key pluck two strings at once changes not just volume but also tonal quality; for instance, when two strings tuned to the same pitch are plucked simultaneously, the note is not just louder but also richer and more complex.
A particularly vivid effect is obtained when the strings plucked simultaneously are anoctave apart. This is normally heard by the ear not as two pitches but as one: the sound of the higher string is blended with that of the lower one, and the ear hears the lower pitch, enriched in tonal quality by the additional strength in the upper harmonics of the note sounded by the higher string.
When describing a harpsichord it is customary to specify its choirs of strings, often called itsdisposition. To describe the pitch of the choirs of strings, pipe organ terminology is used. Strings ateight-foot pitch (8') sound at the normal expected pitch, strings at four-foot pitch (4') sound an octave higher. Harpsichords occasionally include a sixteen-foot (16') choir (one octave lower than eight-foot) or a two-foot (2') choir (two octaves higher; quite rare). When there are multiple choirs of strings, the player is often able to control which choirs sound. This is usually done by having a set of jacks for each choir, and a mechanism for "turning off" each set, often by moving the upper register (through which the jacks slide) sideways a short distance, so that their plectra miss the strings. In simpler instruments this is done by manually moving the registers, but as the harpsichord evolved, builders invented levers, knee levers and pedal mechanisms to make it easier to change registration.
Harpsichords with more than one keyboard (this usually means two keyboards, stacked one on top of the other in a step-wise fashion, as with pipe organs) provide flexibility in selecting which strings play, since each manual can be set to control the plucking of a different set of strings. This means that a player can have, for instance, an 8' manual and a 4' manual ready for use, making it possible to switch between them to obtain higher (or lower) pitches or different tone. In addition, such harpsichords often have a mechanism (the "coupler") that couples manuals together, so that a single manual plays both sets of strings.
The most flexible system is the French "shove coupler", in which the lower manual slides forward and backward. In the backward position, "dogs" attached to the upper surface of the lower manual engage the lower surface of the upper manual's keys. Depending on choice of keyboard and coupler position, the player can select any of the sets of jacks labeled in "figure 4" as A, or B and C, or all three.
Figure 4. French shove coupler. To the left: uncoupled keyboards. The depressed upper key lifts the jack A upwards. The depressed lower key lifts jacks B and C. To the right: The upper keyboard is coupled to the lower one by pulling the latter. The depressed upper key lifts the jack A upwards. The depressed lower key lifts jacks A, B and C.
The English "dogleg" jack system (also used in Baroque Flanders) does not require a coupler. The jacks labeled A in Figure 5 have a "dogleg" shape that permits either keyboard to play A. If the player wishes to play the upper 8' from the upper manual only and not from the lower manual, a stop handle disengages the jacks labeled A and engages instead an alternative row of jacks called "lute stop" (not shown in the Figure). A lute stop is used to imitate the gentle sound of a pluckedlute.[6]
Figure 5. Dogleg jack, English coupler system. When depressed, the upper key lifts the "dogleg" jack (jack A) upwards. The lower key lifts all three jacks A, B, and C.
The use of multiple manuals in a harpsichord was not originally provided for the flexibility in choosing which strings would sound, but rather fortransposition of the instrument to play in different keys (seeHistory of the harpsichord).
Some early harpsichords and organs had ashort octave in the lowest register. It replaced rarely used bass notes with more widely used notes.
Some early harpsichords used ashort octave for the lowest register.[citation needed] The rationale behind this system was that the low notes F♯ and G♯ are seldom needed inearly music. Deep bass notes typically form theroot of the chord, and F♯ and G♯ chords were seldom used at this time. In contrast, low C and D, both roots of very common chords, are sorely missed if a harpsichord with lowest key E is tuned to match the keyboard layout. When scholars specify the pitch range of instruments with this kind of short octave, they write "C/E", meaning that the lowest note is a C, played on a key that normally would sound E. In anotherarrangement, known as "G/B', the apparent lowest key B is tuned to G, and apparent C-sharp and D-sharp are tuned to A and B respectively.
The wooden case holds in position all of the important structural members: pinblock, soundboard, hitchpins, keyboard, and the jack action. It usually includes a solid bottom, and also internal bracing to maintain its form without warping under the tension of the strings. Cases vary greatly in weight and sturdiness: Italian harpsichords are often of light construction; heavier construction is found in the later Flemish instruments and those derived from them.
A false inner–outer harpsichord from theDeutsches Museum inMunich. The false inner case begins to the right of the keyboard, and continues backward only far enough to provide a slot to support the jack rail.
The case also gives the harpsichord its external appearance and protects the instrument. A large harpsichord is, in a sense, a piece of furniture, as it stands alone on legs and may be styled in the manner of other furniture of its place and period. Early Italian instruments, on the other hand, were so light in construction that they were treated rather like a violin: kept for storage in a protective outer case, and played after taking it out of its case and placing it on a table.[7] Such tables were often quite high – until the late 18th century people usually played standing up.[7] Eventually, harpsichords came to be built with just a single case, though an intermediate stage also existed: thefalse inner–outer, which for purely aesthetic reasons was built to look as if the outer case contained an inner one, in the old style.[8] Even after harpsichords became self-encased objects, they often were supported by separate stands, and some modern harpsichords have separate legs for improved portability.
Many harpsichords have a lid that can be raised, a cover for the keyboard, and amusic stand for holding sheet music and scores.
Harpsichords have been decorated in a great many different ways: with plain buff paint (e.g. some Flemish instruments), with paper printed with patterns, with leather or velvet coverings, withchinoiserie, or occasionally with highly elaborate painted artwork.[9][clarification needed]
Jan Vermeer's famous paintingLady Standing at a Virginal shows a characteristic practice of his time, with the instrument mounted on a table and the player standing.
The virginal is a smaller and simpler rectangular form of the harpsichord having only one string per note; the strings run parallel to the keyboard, which is on the long side of the case.
A spinet is a harpsichord with the strings set at an angle (usually about 30 degrees) to the keyboard. The strings are too close together for the jacks to fit between them. Instead, the strings are arranged in pairs, and the jacks are in the larger gaps between the pairs. The two jacks in each gap face in opposite directions, and each plucks a string adjacent to the gap.
The English diaristSamuel Pepys mentions his "tryangle" several times. This was not the percussion instrument that we calltriangle today; rather, it was a name for octave-pitched spinets, which were triangular in shape.
A clavicytherium is a harpsichord with the soundboard and strings mounted vertically facing the player, the same space-saving principle as anupright piano.[10] In a clavicytherium, the jacks move horizontally without the assistance of gravity, so that clavicytherium actions are more complex than those of other harpsichords.
An ottavino built byArnold Dolmetsch in 1923, and modeled after a 1698 instrument by Joannes Carcassi
Ottavini are small spinets or virginals atfour-foot pitch. Harpsichords at octave pitch were more common in the early Renaissance, but lessened in popularity later on. However, the ottavino remained very popular as a domestic instrument in Italy until the 19th century. In the Low Countries, an ottavino was commonly paired with an8' virginals, encased in a small cubby under the soundboard of the larger instrument. The ottavino could be removed and placed on top of the virginal, making, in effect, a double manual instrument. These are sometimes called 'mother-and-child'[11] or 'double' virginals.[12][13]
Occasionally, harpsichords were built which included another set or sets of strings underneath and played by foot-operatedpedal keyboard which trigger the plucking of the lowest-pitched keys of the harpsichord. Although there are no known extant pedal harpsichords from the 18th century or before, from Adlung (1758): the lower set of usually 8' strings "...is built like an ordinary harpsichord, but with an extent of two octaves only. The jacks are similar, but they will benefit from being arranged back to back, since the two [bass] octaves take as much space as four in an ordinary harpsichord[14] Prior to 1980 when Keith Hill introduced his design for a pedal harpsichord, most pedal harpsichords were built based on the designs of extant pedal pianos from the 19th century, in which the instrument is as wide as the pedalboard.[15] While these were mostly intended as practice instruments for organists, a few pieces are believed to have been written specifically for the pedal harpsichord. However, the set of pedals can augment the sound from any piece performed on the instrument, as demonstrated on several albums byE. Power Biggs.[16]
Thearchicembalo, built in the 16th century, had an unusual keyboard layout, designed to accommodate varianttuning systems demanded by compositional practice and theoretical experimentation. More common were instruments withsplit sharps, also designed to accommodate the tuning systems of the time.
Thefolding harpsichord was an instrument that could be folded up to make it more compact, thus facilitating travelling with it.
On the whole, earlier harpsichords have smallerranges than later ones, although there are many exceptions. The largest harpsichords have a range of just over fiveoctaves, and the smallest have under four. Usually, the shortest keyboards were given extended range in the bass with a "short octave". The traditional pitch range for a 5-octave instrument is F1–F6 (FF–f‴).
Tuning pitch is often taken to be A4 = 415 Hz, roughly a semitone lower than the modern standard concert pitch of A4 = 440 Hz. An accepted exception is for French baroque repertoire, which is often performed with a = 392 Hz, approximately a semitone lower again. SeeJean-Philippe Rameau'sTreatise on Harmony (1722) [Dover Publications], Book One, chapter five, for insight into French baroque tuning; "Since most of these semitones are absolutely necessary in the tuning of organs and other similar instruments, the following chromatic system has been drawn up." Tuning an instrument nowadays usually starts with setting an A; historically it would commence from a C or an F. The harpsichord uses the bass clef (F clef).
Some modern instruments are built with keyboards that can shift sideways, allowing the player to align the mechanism with strings at either A = 415 Hz or A = 440 Hz. If a tuning other than equal temperament is used, the instrument requires retuning once the keyboard is shifted.[17]
Throughout the historical period, the harpsichord was characteristically decorated; for extensive discussion and illustration see Kottick (2003). Cases were painted in bright colors (especially in 18th century France), or covered with elaborate wood veneer (18th century England), or adorned with sculptural moldings and knobs (Italy). Soundboards bore paintings, either of individual items such as flowers and animals (Flanders, also France), or even (in expensive instruments), full-scale paintings of the kind usually executed on canvas. Keyboards could have the same "white keys" and "black keys" that pianos have today, but builders frequently employed the opposite pattern, with white sharps and black naturals. The study of harpsichord decoration became an important scholarly field in the 20th century, notably with the work of Sheridan Germann (2002), whose knowledge extended to the point of being able to pin down the particular anonymous artists who worked with particular builders.
The first music written specifically for solo harpsichord was published around the early 16th century. Composers who wrote solo harpsichord music were numerous during the whole Baroque era in European countries including Italy, Germany, England and France. Solo harpsichord compositions included dancesuites,fantasias, andfugues. Among the most famous composers who wrote for the harpsichord were the members ofEnglish virginal school of the late Renaissance, notablyWilliam Byrd (c. 1540–1623).
In France, a great number of highly characteristic solo works were created and compiled into four books ofordres byFrançois Couperin (1668–1733).Domenico Scarlatti (1685–1757) began his career in Italy but wrote most of his solo harpsichord works in Spain; his most famous work is his series of555 harpsichord sonatas. Perhaps the most celebrated composers who wrote for the harpsichord wereGeorg Friedrich Händel (1685–1759), who composed numerous suites for harpsichord, and especiallyJ. S. Bach (1685–1750), whose solo works (for instance,The Well-Tempered Clavier and theGoldberg Variations), continue to be performed very widely, often on the piano. Bach was also a pioneer of the harpsichord concerto, both inworks designated as such, and in the harpsichord part of hisFifth Brandenburg Concerto.
Two of the most prominent composers of theClassical era,Joseph Haydn (1732–1809) andWolfgang Amadeus Mozart (1756–1791), wrote harpsichord music. For both, the instrument featured in the earlier period of their careers,[citation needed] and was largely supplanted by the piano starting roughly in the late 1770s.[18]
Through the 19th century, the harpsichord was almost completely supplanted by the piano. In the 20th century, composers returned to the instrument, as they sought out variation in the sounds available to them. Under the influence ofArnold Dolmetsch, theharpsichordistsViolet Gordon-Woodhouse (1872–1951) and in France,Wanda Landowska (1879–1959), were at the forefront of the instrument's renaissance.Concertos for the instrument were written byFrancis Poulenc (theConcert champêtre, 1927–28), andManuel de Falla.Elliott Carter'sDouble Concerto is scored for harpsichord, piano and two chamberorchestras. For a detailed account of music composed for the revived harpsichord, seeContemporary harpsichord.
^In virtually all instances, "more than one" means two. For the one known three-manual instrument, seeHieronymus Albrecht Hass. For forged three-manual instruments, seeLeopoldo Franciolini.
Kottick, Edward (1987).The Harpsichord Owner's Guide. Chapel Hill: University of North Carolina Press.
Kottick, Edward (2003).A History of the Harpsichord. Indiana University Press.ISBN0-253-34166-3. An extensive survey by a leading contemporary scholar.
Russell, Raymond (1973).The Harpsichord and Clavichord: an introductory study (2nd ed.). London: Faber and Faber.ISBN0-571-04795-5.
Boalch, Donald H. (1995)Makers of the Harpsichord and Clavichord, 1440–1840, 3rd ed., with updates by Andreas H. Roth and Charles Mould, Oxford University Press,ISBN0-19-318429-X. A catalogue, originating with work by Boalch in the 1950s, of all extant historical instruments.
Germann, Sheridan (2002) Harpsichord Decoration: A Conspectus. InThe Historical Harpsichord, Vol. 4, A Monograph Series in Honor of Frank Hubbard, ed. by Howard Schott. Pendragon Press.
O'Brien, Grant (1990)Ruckers, a Harpsichord and Virginal Building Tradition, Cambridge University Press,ISBN0-521-36565-1. Covers the innovations of the Ruckers family, the founders of the Flemish tradition.
Skowroneck, Martin (2003)Cembalobau: Erfahrungen und Erkenntnisse aus der Werkstattpraxis [Harpsichord construction: a craftsman's workshop experience and insight], Fachbuchreihe Das Musikinstrument83, Bergkirchen : Bochinsky,ISBN3-932275-58-6. A study (written in English and German) of harpsichord building by a leading figure in the modern revival of historically authentic methods of building.
Zuckermann, Wolfgang (1969)The Modern Harpsichord: Twentieth Century Instruments and Their Makers, New York : October House,ISBN0-8079-0165-2
The New Grove: Early Keyboard Instruments. Macmillan, 1989ISBN0-393-02554-3. (material from here is also available online inGrove Music Online)
Beurmann, Andreas (2012)Harpsichords and More. Harpsichords, Spinets, Clavichords, Virginals. Portraits of a Collection. The Beurmann Collection in the Museum für Kunst und Gewerbe, Hamburg, and at the Estate of Hasselburg in East Holstein, Germany, Hildesheim/Zürich/New York, 2012,ISBN978-3-487-14470-2.
