 | This articleneeds additional citations forverification. Please helpimprove this article byadding citations to reliable sources. Unsourced material may be challenged and removed. Find sources: "HP-GL" – news ·newspapers ·books ·scholar ·JSTOR(September 2016) (Learn how and when to remove this message) |
| Hewlett-Packard Graphics Language | |
|---|---|
| Internet media type | application/vnd.hp-HPGL |
HP-GL, short forHewlett-Packard Graphics Language and often written asHPGL, is aprinter control language created byHewlett-Packard (HP). HP-GL was the primary printer control language used by HPplotters.[1] It was introduced with the plotterHP-9872 in 1977 and became a standard for almost all plotters. Hewlett-Packard'sprinters also usually support HP-GL/2 in addition toPCL.[2]
The language is formed from a series of two letter codes (mnemonics), followed by optional parameters. For instance anarc can be drawn on a page by sending the string:
AA100,100,50;
This meansArc Absolute, and the parameters place the center of the arc at absolutecoordinates 100,100 on the page, with a starting angle of 50degrees measured counter-clockwise. A fourth optional parameter (not used here) specifies how far the arc continues, and defaults to 5 degrees.
When first introduced, HP-GL contained the following commands:
| Command | Meaning |
|---|---|
| Vector Group | |
PA x,y{,x,y{...}} | Plot absolute [i] |
PR x,y{,x,y{....}} | Plot relative [i] |
PD | Pen down |
PU | Pen up |
| Character Group | |
CA n | Designate alternate character set n [i] |
CP spaces, lines | Character plot [d] |
CS m | Designate standard set m [i] |
DI run, rise | Absolute direction [d] |
DR run, rise | Relative direction [d] |
LB c, ..., c | LabelASCII string [c] |
SA | Select alternate character set |
SI wide, high | Absolute character size [d] |
SL tan θ | Absolute character slant (from vertical) [d] |
SR wide, high | Relative character size [d] |
SS | Select standard character set |
UC x, y, pen{, ...} | User defined character [i] |
| Line Type Group | |
LT t{,l} | Designate line type t and length l [d] |
SM c | Symbol mode [c] |
SP n | Select pen [i] |
VA | Adaptive velocity |
VN | Normal velocity |
VS v{,n} | Select velocity v for pen n [i] |
| Digitize Group | |
DC | Digitize clear |
DP | Digitize point |
OC | Output current position and pen status |
OD | Output digitized point and pen status |
| Axes | |
TL tp{,tn} | Tick length [d] |
XT | X axis tick |
YT | Y axis tick |
| Set-Up Group | |
IP p1x,p1y,p2x,p2y | Input p1 and p2 [i] |
IW xlo,ylo,xhi,yhi | Input window [i] |
OP | Output p1 and p2 [i] |
| Configuration Status | |
AP | Automatic pen pickup [i] |
DF | Set default values |
IM e{,s{,p}} | Input e, s and p masks [i] |
IN | Initialize |
OE | Output error [i] |
OS | Output status [i] |
SI w,h | set character width and height |
Formats:
Typical HP-GL files start with a few setup commands, followed by a long string of graphics commands. The file was inASCII (text file)format, for instance:
| Command | Meaning |
|---|---|
| IN; | initialize, start a plotting job |
| IP; | set the scaling points (P1 and P2) to their default positions |
| SP1; | select pen 1 |
| PU0,0; | lift Pen Up and move to starting point for next action |
| PD100,0,100,100,0,100,0,0; | put Pen Down and move to the following locations (draw a box around the page) |
| PU50,50; | Pen Up and move to X,Y coordinates 50,50 |
| CI25; | draw a circle with radius 25 |
| SS; | select the standard character set |
| DT*,1; | set the text delimiter to the asterisk, and do not print them (the 1, meaning "true") |
| PU20,80; | lift the pen and move to 20,80 |
| LBHello World*; | draw a label |
The coordinate system was based on the smallest units one of the HP plotters could support, and was set to 25 μm (i.e. 40 units per millimeter, 1016 per inch).The coordinate space was positive or negativefloating point numbers, specifically ±230.
The original HP-GL language did not support definition of line width, as this parameter was determined by the pens loaded into the plotter. With the advent of the firstinkjet plotters, line width for the "pens" specified within the HP-GL files had to be set at the printer so it would know what line width to print for each pen, a cumbersome and error-prone process. WithHewlett-Packard Graphics Language/2 akaHP-GL/2, definition of line width was introduced into the language and allowed for elimination of this step. Also, among other improvements abinary file format was defined that allowed for smaller files and shorter file transfer times, and the minimal resolution was reduced.
| Command | Meaning |
|---|---|
| NPx | number of pens; x=1..256 |
| PCx,r,g,b | pen color; x=pen, r=red, g=green, b=blue, 0..255 |
| PWw,x | pen width; w=pen width in mm with decimal point, x=pen |
HP-GL is related toAGL (A Graphics Language), an extension of theBASIC programming language. AGL was implemented on Hewlett-Packardminicomputers to simplify controlling a plotter. AGL commands describe the desired graphics plotting function, which the computer relays as several HP-GL instructions to the plotter.
Hewlett-Packard software | ||
|---|---|---|
| Applications and utilities |
|  |
| Database | ||
| File systems and formats | ||
| Operating systems and environments | ||
| Protocols and languages | ||
| ||
