Bridgewater Bridge | |
|---|---|
 The Bridgewater Bridge | |
| Coordinates | 42°44′42″S147°13′33″E / 42.74500°S 147.22583°E /-42.74500; 147.22583 |
| Carries |  Midland Highway |
| Crosses | Derwent River |
| Locale | Hobart,Tasmania, Australia |
| Begins | Granton |
| Ends | Bridgewater |
| Named for | Bridgewater |
| Owner | Department of State Growth |
| Preceded by | Blair Street Bridge |
| Followed by | Bowen Bridge |
| Characteristics | |
| Design | box girder |
| Material | Concrete |
| Total length | 1.2 km (0.7 mi) |
| Clearance below | 16 m (52.5 ft)[1] |
| No. oflanes | 4 |
| History | |
| Constructed by | McConnell Dowell |
| Construction start | October 2022[2] |
| Opened | 1 June 2025 |
| Replaces | Truss bridge withvertical lift(1946-2025) |
| Location | |
 Interactive map of Bridgewater Bridge | |
TheBridgewater Bridge is a 1.2-kilometre-long (0.7 mi) concretebox girder bridge that carries theMidland Highway across theDerwent River inHobart,Tasmania, Australia. This bridge connects the Hobart suburbs ofBridgewater andGranton. It accommodates a four-lanehighway and agrade-separatedfootpath andcycle lane. It is the fifth such bridge at this location to carry this name.[3][4]
The bridge was funded by theAustralian andTasmanian Governments at a cost of $786 million[4] and constructed byMcConnell Dowell.[5] it is expected to service 22,000 trips per day.[6] It is the first bridge at the location to have a marine navigation clearance of greater than 16 metres - consistent with theBowen Bridge.[1]
It was opened in June 2025 to replace the fourth Bridgewater Bridge (Bridgewater Bridge and Causeway), a steeltrussvertical-lift bridge and specially-builtcauseway. This was a two-lane road bridge that also carried theSouth Railway Line until its closure in 2014. This bridge had been in operation since 1946, and was the oldest surviving lift span bridge in Australia; lifting of the bridge caused considerable traffic delays in the bridge's final years.[7]
The Bridgewater Bridge was among the first bridges constructed inTasmania after British settlement in 1803, and gave its name to the nearby suburb ofBridgewater.Lieutenant-GovernorGeorge Arthur commissioned the construction of the bridge and causeway to connect theLaunceston – Hobart Trunk Road, linking both Tasmanian towns and providing easier access to farmlands in theinterior of Tasmania.
Construction commenced on the bridge in 1829. Operations were supervised byRoderic O'Connor.[8] The causeway, which was constructed first, was built by a workforce of 200convicts who had been sentenced to secondary punishment. These convicts, using nothing but wheelbarrows, shovels and picks and muscle power, shifted 2 million tonnes (2.2 million short tons) of soil, stones and clay. The finished causeway stretched 1.3 kilometres (1 mi), although did not span the full width of the Derwent. The original plan apparently called for aviaduct, but this plan was abandoned and the half-built arches were filled in to form the present causeway.
Upon completion of the causeway, apunt operated across the deep, navigable section of the river, but could not cope with traffic demands. To resolve this issue, an Act of Parliament was passed in 1846 to enable construction of a bridge.[9] The accepted design was a timber bridge, was by the firm of architect and former convictJames Blackburn.[10] Being asliding bridge, it could slide back to allow shipping to pass through. Construction started in 1848, and opened to traffic in April 1849.[11]
In the early 1870s, theTasmanian Main Line Railway called for widening of the causeway so the railway could be laid on the downstream side. A second bridge was built alongside the first, parallel to it. The northern abutment was about 50 feet downstream from the road bridge. This bridge featured aswing span opening.[12][11] Construction commenced in 1869 and it was completed 1874.[11]
On 22 July 1886, a train from the north was passing over the bridge when the engine left the tracks and tipped over, hanging precariously above the water on the edge of the southern end of the swing bridge.[13] Two people, fireman William Shaw[14] and passenger Daniel Turner, died as a result of the accident.[15][16] The driver was injured. The locomotive was salvageable. The cause of the accident was found to be that the rails failed to match properly when the bridge was closed, so the bridge was modified again to solve this problem.
In 1891 a new bridge was built on the upstream side of the road and rail bridges, and this too, had an opening swing span. Although initially planned as a road crossing, this bridge was designed to be a permanent railway bridge, and was built as a straight line extension of the causeway, with the northern abutment being some 60 metres upstream from the other bridges. When this third bridge was completed in 1893, it was initially used as road bridge, to divert traffic off the 1849 road bridge which was deteriorating rapidly. For six years there were three bridges crossing the Derwent simultaneously, as it was not until 1899 that the 1849 draw-back bridge (the first bridge) was finally dismantled. The introduction of heavier locomotives necessitated the transfer of the railway to the 1893 bridge. In 1907-08 the causeway was widened again, this time on the upstream side, and the tracks laid flush in the centre of the roadway on the 1893 bridge. This would be Bridgewater's modern joint road-rail bridge going forward, but would not be without problems. Road users complained of delays from waiting for trains to cross and the frequent opening of the swing span for river craft lead to near misses and irked local residents. A public meeting was held and the State Government was pressured to make the old 1874 TMLR railway bridge available for road traffic. New piles were added to the 1874 rail bridge, the rails lifted, and the deck converted to a roadway. By November 1908 both bridges had swapped roles: the 1893 road bridge became a railway bridge (as always intended), and the old 1874 railway bridge had now become a road bridge (as never intended). The concrete and steel caisson pivot and the sandstone abutments of the 1893 road/railway bridge are still standing and can be viewed on the upstream or left side of the present bridge as one travels towards the north.[17]
Both the first and second bridges did not run straight off the end of the causeway; rather, they turned slightly to the right, or downstream. The first swing bridge (originally the TMLR rail bridge) was left standing when the present lifting bridge was being constructed to prevent traffic stoppages, so the present bridge deviates from the causeway quite appreciably.
Bridgewater Bridge | |
|---|---|
 Fourth Bridgewater Bridge (1946-2025) | |
| Coordinates | 42°44′27″S147°13′31″E / 42.7408°S 147.2253°E /-42.7408; 147.2253 |
| Carries | Midland Highway South Railway Line |
| Crosses | Derwent River |
| Locale | Hobart,Tasmania, Australia |
| Begins | Granton |
| Ends | Bridgewater |
| Named for | Bridgewater |
| Owner | Department of State Growth |
| Characteristics | |
| Design | Truss bridge withvertical lift |
| Material | Steel |
| Piers in water | 13 |
| No. oflanes | 2 |
| Rail characteristics | |
| No. oftracks | 1 |
| Track gauge | 1,067 mm (3 ft 6 in) |
| History | |
| Construction start | 1939 |
| Opened | 1946 |
| Closed | 2025 |
| Replaces | Swingpunt(c. 1900s-1946) |
| Replaced by | Four-lane concretebox girder |
 | This sectionneeds additional citations forverification. Please helpimprove this article byadding citations to reliable sources in this section. Unsourced material may be challenged and removed.(December 2020) (Learn how and when to remove this message) |
Construction on the steel vertical lift bridge across the Derwent began in 1939.[18] Construction was interrupted byWorld War II;[19] the bridge opened to road traffic in March 1942,[20] with completion of the lifting segment finally completed in early 1946.[21] The bridge opened to rail traffic in late 1946.[22] It consists of a long concrete bridge that leads off the end of the causeway, and a steel lifting section just before the northern bank of the river. The lifting section is one of only a few remaining in theSouthern Hemisphere, and is the largest of its kind remaining in Australia. The bridge was designed to last a century without replacement. A small control house stands on the lifting section. Inside are the switches and locks which operate the bridge.
Until 1984, theAustralian Newsprint Mills atBoyer moved all its produce by river.Barges were used to transport paper from the mill to the storage sheds at Pavilion Point at Hobart, and for this reason the bridge was required to open very frequently. Consequently, a bridge-keeper lived on-site and opened and closed the bridge when required. However, when the decision was made to cease river transportation, an on-site keeper was no longer necessary, so bridge openings became less frequent.
In response to vandalism of the house which contains the bridge operating controls,closed-circuit television cameras were installed along the lifting span sometime between 2003 and 2005.
On 30 October 2006 a fault was found in one of the steel cables holding up the two 170-tonne (190-short-ton) concrete counterweights above the road, forcing the temporary closure of the bridge.[23] This closure caused peak hour traffic delays, mainly along theEast Derwent Highway, due to traffic being diverted over theBowen andTasman bridges. The cables, which were put in place in 1994, were supposed to have a 20-year lifespan and had lasted barely over half that time.
From 2006 until 2010, the lifting segment of the Bridgewater Bridge was out of commission, due to failed maintenance. The State Government spent $14 million to refurbish the bridge and provide it with a further 15 years of life, until a replacement could be built.[24] This refurbishment replaced the vandalised control house and its controls and all of the cabling to raise and lower the bridge. Touted as a "major tourist attraction" with expected regular openings for tourist and private vessels to travel between Hobart andNew Norfolk, the bridge refurbishment was a failure, only successfully opening a handful of times.[7]
Rail services ceased using the bridge when the South Line was cut back to terminate at theBrighton Transport Hub in June 2014.[25][26] The bridge received an Engineering Heritage Marker fromEngineers Australia in 2018 as part of itsEngineering Heritage Recognition Program.[27]
Between 2001 and 2005, theAustralian Government set aside $100 million towards the replacement of the Bridgewater Bridge,[28] soon after theTasmanian Government decided to build the replacement to the south of the existing bridge. However, after years of inaction the State government has encountered someheritage issues with replacing the bridge and is to be replaced as part of the final stage of theBrighton Bypass and Midland Highway upgrade.
Towards the end of 2010, the State government released plans for a new Derwent River crossing, next to the existing bridge.[29] The new bridge would carry the Midland Highway and the old bridge will be left open for rail, pedestrian and local traffic. While the Bridgewater Bridge is recognised as being limited in its ability to perform the function of the Midland Highway, it also has important heritage values and is recognised as a landmark in the area.[30][31]
In March 2016, Infrastructure Tasmania published its review of a design and cost estimate for the construction of a replacement structure for the existing Bridgewater Bridge, which considered various options for a replacement structure and provided advice as to the most feasible crossing solution. As part of the2018–19 federal budget, the Australian Government announced a $461 million grant towards the construction of a new Bridgewater Bridge, representing 80 per cent of the expected total construction cost. The Tasmanian Government is expected to contribute $115 million.[32] Construction was expected to commence in 2019;[33] however, following independent assessment of the project byInfrastructure Australia in July 2019, the evaluation identified a range of issues, which may add to costs and require further work to address, and recommended that the Tasmanian Government revise its business case. The project was scheduled to start design and approvals in 2019, with the design to be agreed by the end of 2020. Substantive construction was expected to commence in 2022 and completion was targeted in 2024.[34]
The project scope also included re-configuration of the interchanges at Granton and Bridgewater to providegrade-separated access.[5]
The bridge officially opened to traffic on the evening of 1 June 2025, following a community walk over the bridge earlier that day.[35] The first vehicle to cross the bridge was a vintage 1910Star Roadster, carrying two women, Margaret McMaster and Barbara Jones, who were present at the previous bridge's opening in 1946.[6]
The bridge includes two fixedspeed cameras[3] and two electronicvariable-message signs.[36]
Bridges of theRiver Derwent | ||||
|---|---|---|---|---|
| ||||
 Road infrastructure in GreaterHobart | ||
|---|---|---|
| Highways |  | |
| Major roads | ||
| Bridges | ||
| Interchanges | ||
| Proposals | ||
