Aimpoint is acontractor for theUnited States military and supplies theAimpoint CompM4. Aimpoint products are used by various armed forces, and are marketed to civilians for hunting and sport. The Aimpoint Comp sights, such as the CompM2, are Aimpoint's most popular product line.
Aimpoint is a manufacturing company founded in 1974.[1] Their primary products arereflector (or reflex) sights, specifically thered dot sight sub-type. In 1975 they introduced their first product,[2] the "Aimpoint Electronic" red dot sight, based on a design byHelsingborg engineerJohn Arne Ingemund Ekstrand.[3] This is the firstlight emitting diode (LED) "red dot" reflector sight manufactured.[citation needed] Aimpoint currently offers various products based on this technology. In 1997 theUS Army awarded Aimpoint the first military contract for a red dot sight, theAimpoint CompM2, designated the “M68 Close Combat Optic”.[4][5]
Aimpoint on anAK4Ak 5D seen here with anAimpoint red dot sight.Hunter with Aimpoint Micro H-2 on rifle
Aimpoint's red dot sights are marketed to hunters, marksmen, law-enforcement agencies, and military organizations.[6] Nearly 3,000,000 sights are in use world wide today.[citation needed]
Their products use non-magnifyingoptical collimators (reflector or "reflex" sights) and battery powered LEDs to produce an illuminated red dotreticle. Many sights utilize amangin mirror system, consisting of ameniscus lens corrector element combined with a semi-reflective mirror (referred to as a "two lens" or "double lens" system by Aimpoint[7]), that compensates forspherical aberration, an error that can cause the dot position to diverge from the sight'soptical axis with change in eye position.[8][9][10] Aimpoint markets their sights as "parallax free",[11][citation needed] but this seems to refer to their off-axis spherical aberration correction system at one optimized viewing distance. Aimpoints, like all collimated sight systems, induce some parallax at non-optimized viewing distances.[12][13]
Aimpoint has separate distributors for their military and civilian products in many countries.[14][15][citation needed]
Left: Aimpoint Acro C2 reflex sight laying on its side. Right: Acro rail on aPicatinny riser.Approximate dimensions of an Aimpoint Acrodovetail rail.
Aimpoint has launched a series of proprietarymounts for their products. These include:
Aimpoint CompM4 mount: Launched in 2007[16] with the Aimpoint CompM4 sight. The sight is attached to the mount via two M5 screws from the underside, and the mount has a transverse groove acting as a recoil lug. The Aimpoint Comp line was launched in 1993.[16] The predecessor of the CompM4,CompM2, had a 30 mmring mount and was introduced in the American military in 2000. Some manufacturers have copied the M4 mount system, but it has mainly been used by Aimpoint.[17][citation needed]
Aimpoint Micro mount: Launched in 2007[18] together with the compact Aimpoint Micro series of sights (T1 and H1, and later T2 and H2). The sight is attached to the mount with four M3 screw. The mount has a longitudinal profile which is reminiscent of theZeiss rail, but with other dimensions and a square recoil lug in the middle. The profile is also longitudinally slightly offset from the centerline. The standard has been copied by many other manufacturers, and has been a common mounting standard for reflex sights in sizes similar to the Aimpoint Micro (such asHolosun 403B, Minox RV1, SIG Sauer Romeo4, Vortex Crossfire and Aimpoint Comp M5b[19]). In addition to being offered as the mounting surface on sights from many other optics manufacturers, there are also many aftermarket mounts available for this pattern.[20]
Aimpoint Acro rail: Launched in 2019 together with the sights Aimpoint Acro P-1 and C-1.[21] This is a mount without screws acting directly between the sight and the mount, and is slim enough (approximately 15 mm wide and 2 mm tall) so that it can be milled directly into most pistol slides. The mount is adovetail rail with a thick transverse recoil lug (4 mm) and is reminiscent of a miniaturized version of thePicatinny rail, but with a lower and slimmer profile, and fewer edges exposed to the user. With competing standards for attaching miniature red dot sights to pistols (such as the Docter, Trijicon, C-more and Shield/Leupold mounting standards), experience among competition shooters has shown that the screws used for attaching the sight directly to the mount can wear due to inadvertently taking up recoil, including both normal recoil from firing as well as negative recoil from when the slide closes during feeding, resulting in the screws wearing and needing to be replaced over time. The Acro mount does not use such screws, but instead has a clamp mount. Due to using a clamp mount (similar to the Picatinny), no screws are needed to attach the sight to the mount rail. The Acro rail has so far been used on Aimpoint Acro (P1, C1, P2, C2) and Steiner MPS.[21]
^List includes: US Army, US Navy, US Air Force, US Marine Corps, USSOCOM units, the FBI's Hostage Rescue Team, French Army, Swedish Army, Danish Army, Finnish Army, Norwegian Army, Latvian Army, Slovenian Army, and Italian Army[citation needed]
