A Novel Method for the Micro-Clearance Measurement of a Precision Spherical Joint Based on a Spherical Differential Capacitive Sensor

Wen Wang

He Yang

^1,*

Min Zhang

¹,

Zhanfeng Chen

Guang Shi

¹,

Keqing Lu

¹,

Kui Xiang

² and

Bingfeng Ju

^2,3

School of Mechanical Engineering, Hangzhou Dianzi University, Hangzhou 310018, China

School of Mechanical Engineering, Zhejiang University, Hangzhou 310027, China

State Key Lab of Fluid Power & Mechatronic Systems, Zhejiang University, Hangzhou 310027, China

Author to whom correspondence should be addressed.

Sensors2018,18(10), 3366;https://doi.org/10.3390/s18103366

Submission received: 15 September 2018 /Revised: 2 October 2018 /Accepted: 5 October 2018 /Published: 9 October 2018

(This article belongs to the SectionPhysical Sensors)

Downloadkeyboard_arrow_down

Browse Figures

Versions Notes

Abstract

A spherical joint is a commonly used mechanical hinge with the advantages of compact structure and good flexibility, and it becomes a key component in many types of equipment, such as parallel mechanisms, industrial robots, and automobiles. Real-time detection of a precision spherical joint clearance is of great significance in analyzing the motion errors of mechanical systems and improving the transmission accuracy. This paper presents a novel method for the micro-clearance measurement with a spherical differential capacitive sensor (SDCS). First, the structure and layout of the spherical capacitive plates were designed according to the measuring principle of capacitive sensors with spacing variation. Then, the mathematical model for the spatial eccentric displacements of the ball and the differential capacitance was established. In addition, equipotential guard rings were used to attenuate the fringe effect on the measurement accuracy. Finally, a simulation with Ansoft Maxwell software was carried out to calculate the capacitance values of the spherical capacitors at different eccentric displacements. Simulation results indicated that the proposed method based on SDCS was feasible and effective for the micro-clearance measurement of the precision spherical joints with small eccentricity.

Keywords:

spherical joint;clearance measurement;eccentric displacement;capacitor

1. Introduction

Because of the advantages of compact structure, good flexibility, and high carrying capacity, precision spherical joints are widely used for three-degree-of-freedom (DOF) mechanical hinges in many types of equipment, such as parallel mechanisms, industrial robots, and automobiles [1]. In actual applications of spherical joints, the clearance between the ball and the socket inevitably exists, due to manufacturing or installation errors. As a result, during the process of transmitting motion or force with spherical joints, the actual position and orientation of the output shaft may deviate from the ideal pose, which affects the overall transmission accuracy of the system. Therefore, real-time detection of a precision spherical joint clearance is of great significance in analyzing the motion errors of the application systems (e.g., robot joints) and improving the transmission accuracy [2].

The clearance measurement is essentially the detection of the relative linear displacement between two components. In the case of a precision spherical joint, the clearance measurement can be achieved by detecting the eccentric displacements of a ball (3-DOF motion in space) and the socket (fixed in space). Many methods have been proposed for the clearance measurement in industrial applications, for example, the inductive sensor-based method [3], the optical fiber-based method [4], the microwave-based method [5], and other methods based on eddy current sensors [6] or capacitive sensors [7]. However, studies focused on the clearance measurement of a precision spherical joint have been rarely reported. Recently, Endemano et al. [8] presented a two-dimensional (2D) study for calculating the capacitances of rotating objects with eccentricity. Han et al. [9] carried out a micro-displacement detection of a spherical rotor with regard to electrostatically suspended gyroscope technology. In the electrostatically suspended gyroscope’s rotor-bearing system, the spherical rotor was steadily suspended by electrostatic forces in a high vacuum chamber. The drift of the spherical rotor from the center of the cavity was obtained by detecting the variation of the spherical capacitance between electrodes and the rotor. This real-time drift was then used as a feedback signal to generate the feedback control of the electrostatic force. The spherical detecting electrode usually consisted of several electrodes (e.g., six, eight or twelve electrodes) [10,11,12,13,14]. Since the clearance of a spherical joint exhibits similar characteristics with that of a spherical rotor, this micro-displacement detection method used for the spherical rotor may provide an inspiration for spherical gap measurement.

A capacitive sensor is widely used for high-precision displacement detection in many applications [15,16]. It is a typical non-contact measurement device with high accuracy, good dynamic performance, high resolution, and strong adaptability to harsh environments (e.g., high temperature). Thus, in this paper, a spherical differential capacitive sensor (SDCS) is proposed to measure spatially eccentric displacements of the ball of a precision spherical joint. First, the structure and measuring principle of the SDCS is introduced. Then, the mathematical model for the relation between spatial eccentric displacements and differential capacitances is presented. Finally, the feasibility of the proposed method is validated by calculating the capacitance for different eccentric displacements using commercial software Ansoft Maxwell 16.0 (Ansoft, Pittsburgh, PA, USA).

2. Structural Design and Measuring Principle

The SDCS proposed in this work consists of a ball (excitation electrode,CE_d) and eight spherical capacitive plates (sensing electrodes,CE_si,i = 1, 2, …, 8), as shown inFigure 1a. The ball of the spherical joint is used as a common electrode, whereas each of the eight spherical capacitive plates is employed as a spherical capacitorC_i,i = 1, 2, …, 8. The coordinate systemOXYZ is defined inFigure 1b, with the originO chosen at the center of the spherical capacitive plates. Eight spherical capacitive plates having the same structure size are concentrically fixed in the spherical joint’s socket, and they are symmetrically distributed in eight quadrants of the three-dimensional coordinate system (Figure 1b). Teflon-laced epoxy with a certain thickness, known as an abrasion-resistant material with self-lubricating properties, was deposited on the inner surface of the spherical capacitive plates. This ensured the insulation between the excitation electrode and the sensing electrodes. Moreover, as a dielectric material, Teflon-laced epoxy can improve the sensitivity of the capacitive sensor.

Ideally, the center of the ball coincides with that of the spherical capacitive plates, and the clearances between the ball and each of the eight spherical capacitive plateshave identical values. As such, eight spherical capacitors have the same value in capacitance. Once the ball has an eccentric displacement relative to the socket, the clearances between the eight spherical capacitive plates and the ball exhibit diverse variations, and thus the capacitance value of each spherical capacitor varies accordingly. In other words, the eccentric displacements of the ball can be obtained by detecting the capacitance of the eight spherical capacitors.

To obtain the micro-clearance of a precision spherical joint (i.e., the three-dimensional displacement of the ball), three pairs of differential capacitance units were established for the eccentric displacement measurement along theX,Y andZ directions, respectively. The differential capacitance unit pair denoted a pair of differentialcapacitanceunits that faced each other with a 180° phase shift. As shown inTable 1,C_up-X,C_up-Y andC_up-Z denoted the differential capacitance unit pairs along theX,Y andZ directions, respectively. Each pair consisted of unit 1 and unit 2, and each unit included four adjacent capacitors. The eccentric displacements of the ball were calculated from the capacitance values of each differential capacitance unit pair. Specifically, the eccentric displacementδ_X of the ball along theX direction was obtained by calculating the capacitance difference between the two differential capacitance units along theX direction, one being the unit that consisted ofC₁,C₄,C₅ andC₈, and the other being the unit that consisted ofC₂,C₃,C₆ andC₇. Similarly, the eccentric displacementδ_Y of the ball along theY direction and the eccentric displacementδ_Z of the ball along theZ direction was acquired by calculating the capacitance difference of the corresponding differential capacitance unit pair, respectively. Thus, the eccentric displacement componentδ_X,δ_Y andδ_Z of the ball can be given by the following equations:

δ_{X} = f_{X} (C_{1} + C_{4} + C_{5} + C_{8} - C_{2} - C_{3} - C_{6} - C_{7}),

(1)

δ_{Y} = f_{Y} (C_{1} + C_{2} + C_{5} + C_{6} - C_{3} - C_{4} - C_{7} - C_{8}),

(2)

δ_{Z} = f_{Z} (C_{1} + C_{2} + C_{3} + C_{4} - C_{5} - C_{6} - C_{7} - C_{8}),

(3)

wheref_X,f_Y andf_Z denote the transition function for the measured capacitance and the eccentric displacement component in theX,Y andZ directions, respectively. Their values were determined by the structural parameters of the eight spherical capacitors. In order to simplify the expressions of the differential capacitances along theX,Y andZ directions, ΔC_X, ΔC_Y and ΔC_Z are defined as follows:

Δ C_{X} = C_{1} + C_{4} + C_{5} + C_{8} - C_{2} - C_{3} - C_{6} - C_{7},

(4)

Δ C_{Y} = C_{1} + C_{2} + C_{5} + C_{6} - C_{3} - C_{4} - C_{7} - C_{8},

(5)

Δ C_{Z} = C_{1} + C_{2} + C_{3} + C_{4} - C_{5} - C_{6} - C_{7} - C_{8} .

(6)

To approximately calculate the capacitance value of each spherical capacitor, two assumptions were made: (1) the area element dA of a spherical capacitor was regarded as a parallel-plate capacitor with an equal gap; (2) the fringe effect of the spherical capacitive plates was not taken into consideration. Based on the above assumptions, the capacitance of the spherical capacitor element dC was calculated based on the formula of a parallel-plate capacitor. Then, the capacitance value of each spherical capacitor was obtained using the following integral:

C_{i} = ε \iint_{A_{i}} \frac{1}{e} d A (i = 1, 2, \dots, 8),

(7)

whereε is the permittivity of the dielectric which includes the abrasion-resistant material and a small quantity of air,e is the clearance between the ball and each spherical capacitive plate, andA_i is the effective area of the spherical capacitive plate for each spherical capacitorC_i,i = 1, 2,…, 8.

3. Mathematical Model

3.1. Calculation of the Clearance between the Ball and the Spherical Capacitive Plates

Figure 2 presents the coordinate systemOXYZ in which the center of the ball deviates from that of the spherical capacitive plates. The unit vectors along theX,Y andZ directions are denoted byi,j andk, respectively.θ is the zenithal angle between the output shaft central axis of the spherical joint and the positive direction of theZ axis,

0 \leq θ \leq π

.φ is the azimuthal angle between the projection of the output shaft central axis onto the planeXOY and the positive direction of theX axis,

0 \leq φ \leq 2 π

. The pointP is on the surface of the ball, and the outward unit normal vectorn of the vectorOP in the coordinate systemOXYZ is given by the following equation:

n = \sin θ \cos φ i + \sin θ \sin φ j + \cos θ k .

(8)

The inner surface of the spherical capacitive plates and the outer surface of the ball are considered as ideal spheres. As shown inFigure 2,R₀ denotes a spherical radius of the inner surface of the spherical capacitive plates.r is the radius of the ball.δ is the linear displacement between the centerO of the socket and the centerO’ of the ball. Therefore, the spatially eccentric displacement of the ball can be written in the form of a vector as follows:

δ = δ_{X} i + δ_{Y} j + δ_{Z} k .

(9)

As shown inFigure 2, the line joining the two pointsO’ andP is extended to intersect with the inner surface of the spherical capacitive plates at the pointQ. The distance from pointQ to pointP is defined as the clearancee at the pointP. The initial clearance of the ball without eccentricity is denoted bye₀, that is,

e_{0} = R_{0} - r

. If the ball has an eccentric displacement relative to the socket, the clearance at the pointP in the case of

e ≪ R_{0}

can be given by the following equation:

e = R_{0} - δ_{X} \sin θ \cos φ - δ_{Y} \sin θ \sin φ - δ_{Z} \cos θ - r .

(10)

To simplify the subsequent calculations, dimensionless parameters are introduced as follows:

k = \frac{e}{e_{0}}, λ_{X} = \frac{δ_{X}}{e_{0}}, λ_{Y} = \frac{δ_{Y}}{e_{0}}, λ_{Z} = \frac{δ_{Z}}{e_{0}} .

Therefore, Equation (10) can be rewritten in the following dimensionless form:

k = 1 - λ_{X} \sin θ \cos φ - λ_{Y} \sin θ \sin φ - λ_{Z} \cos θ .

(11)

3.2. Relation between Capacitance of Spherical Capacitors and Eccentric Displacements

Let

λ = λ_{X} \sin θ \cos φ + λ_{Y} \sin θ \sin φ

, assuming obviously thatλ < 1. It is also assumed that the eccentric displacement of the ball is small.

Using Taylor’s expansion method for 1/k, it becomes the following Taylor’s series:

\frac{1}{k} = \frac{1}{1 - λ} = 1 + λ + λ^{2} + λ^{3} + \dots .

(12)

Substituting Equations (11) and (12) into Equation (7), the following equation is obtained:

C_{i} = \frac{ε}{e_{0}} \iint_{A_{i}} [1 + E (θ, φ)] d A (i = 1, 2, \dots, 8),

(13)

where

E (θ, φ) = \sum_{n = 1}^{\infty} {(λ_{X} \sin θ \cos φ + λ_{Y} \sin θ \sin φ + λ_{Z} \cos θ)}^{n}

and dA is the area element of the spherical capacitive plates at the pointQ (i.e.,

d A = R_{0}^{2} \sin θ d θ d φ

The capacitance of each spherical capacitor can be obtained according to Equation (13). Then, the differential capacitance ΔC_X, ΔC_Y and ΔC_Z can be calculated by substituting the capacitance of each spherical capacitor into Equations (4)–(6), respectively. Therefore, the mathematical model of the relation between the differential capacitance and the spatial eccentric displacements can be established.

Equation (13) can be further rewritten as follows:

C_{i} = K_{i} (λ_{X}, λ_{Y}, λ_{Z}) \frac{ε R_{0}^{2}}{e_{0}} (i = 1, 2, \dots, 8),

(14)

where

K_{i} (λ_{X}, λ_{Y}, λ_{Z}) = \iint_{A_{i}} [1 + E (θ, φ)] \sin θ d θ d φ

As for the spherical capacitive plateCE_si(i = 1, 2, …, 8) shown inFigure 3,

ζ

is the corresponding angle of arc length in the longitude direction, and

θ_{i}

denotes the initial zenithal angle between the upper edge of the spherical capacitive plate and the positive direction of theZ axis.

ξ

is the corresponding angle of arc length in the latitude direction, and

φ_{i}

denotes the azimuthal angle between the projection of the left edge of the spherical capacitive plate onto the planeXOY and the positive direction of theX axis. Accordingly,

K_{i} (λ_{X}, λ_{Y}, λ_{Z})

can be expressed as follows:

K_{i} (λ_{X}, λ_{Y}, λ_{Z}) = \int_{θ_{i}}^{θ_{i} + ζ} \int_{φ_{i}}^{φ_{i} + ξ} [1 + E (θ, φ)] \sin θ d θ d φ .

(15)

K_i (λ_X,λ_Y,λ_Z) can be solved according to Equation (15), after the layout and size of the spherical capacitive plates are determined. Since the eight spherical capacitive plates have the same structure size and are symmetrically distributed in space, and if the size and layout of the spherical capacitive plateCE_s1 is known, other spherical capacitive plates can be determined. Considering the height restrictions of the spherical joint top-cover, let

θ_{1} = 5 π / 18

ζ = π / 6

φ_{1} = π / 12

, and

ξ = π / 3

. Taking the spherical capacitorC₁ as an example, the corresponding

K_{1} (λ_{X}, λ_{Y}, λ_{Z})

is calculated as follows by neglecting the terms of degree above 3:

\begin{array}{l} K_{1} (λ_{X}, λ_{Y}, λ_{Z}) = 0.4913 + 0.2987 λ_{X} + 0.2987 λ_{Y} + 0.2005 λ_{Z} + \dots \\ 0.2002 λ_{X}^{2} + 0.2002 λ_{Y}^{2} + 0.0909 λ_{Z}^{2} + 0.3311 λ_{X} λ_{Y} + \dots \\ 0.2383 λ_{X} λ_{Z} + 0.2383 λ_{Y} λ_{Z} + 0.1434 λ_{X}^{3} + 0.1434 λ_{Y}^{3} + \dots \\ 0.0445 λ_{Z}^{3} + 0.3073 λ_{X} λ_{Y}^{2} + 0.3073 λ_{X}^{2} λ_{Y} + 0.1588 λ_{X} λ_{Z}^{2} + \dots \\ 0.2341 λ_{X}^{2} λ_{Z} + 0.1588 λ_{Y} λ_{Z}^{2} + 0.2341 λ_{Y}^{2} λ_{Z} + 0.3873 λ_{X} λ_{Y} λ_{Z} \end{array}

(16)

Similarly,

K_{i} (λ_{X}, λ_{Y}, λ_{Z}) (i = 2, \dots, 8)

for the other spherical capacitors can be obtained. Then, the capacitance value for each capacitor can be calculated according to Equation (14). By further substituting each capacitance into Equations (4)–(6), the following equations are obtained:

Δ C_{X} = \frac{ε R_{0}^{2}}{e_{0}} Δ K_{X},

(17)

Δ C_{Y} = \frac{ε R_{0}^{2}}{e_{0}} Δ K_{Y},

(18)

Δ C_{Z} = \frac{ε R_{0}^{2}}{e_{0}} Δ K_{Z},

(19)

where

Δ K_{X} = 2.3896 λ_{X} + 1.1472 λ_{X}^{3} + 2.4584 λ_{X} λ_{Y}^{2} + 1.2704 λ_{X} λ_{Z}^{2},

(20)

Δ K_{Y} = 2.3896 λ_{Y} + 1.1472 λ_{Y}^{3} + 2.4584 λ_{Y} λ_{X}^{2} + 1.2704 λ_{Y} λ_{Z}^{2},

(21)

Δ K_{Z} = 1.6040 λ_{Z} + 0.3560 λ_{Z}^{3} + 1.8728 λ_{Z} λ_{X}^{2} + 1.8728 λ_{Z} λ_{Y}^{2} .

(22)

It can be seen from Equations (20)–(22) that the even-order terms of dimensionless eccentric displacements of the ball in the socket are eliminated. This can be ascribed to the symmetrically spatial distribution of the eight spherical capacitive plates and the differential calculation for the capacitance of the spherical capacitors. Thus, the proposed method can improve the sensitivity of the sensor and effectively reduce nonlinear errors.

To examine the effect of the third-order terms, the dimensionless eccentric displacements of the ball with and without the third-order terms were compared in detail. Two cases were considered, one being the displacements only in each axis direction (λ_X = 0,λ_Y = 0 orλ_Z = 0), the other being the displacements in a non-axis direction (λ_X ≠ 0,λ_Y ≠ 0 andλ_Z ≠ 0).

Figure 4 compares the first-order term and the sum of the four terms of dimensionless eccentric displacements in the case of the displacement in the single-axis direction. First, if the displacement of the ball occurs in theX direction (λ_X ≠ 0 andλ_Y =λ_Z = 0), the relative error between ΔK_X and its first-order term is 0.48% and 1.88% atλ_X = 0.1 and 0.2, respectively (Figure 4a). Second, if the displacement occurs in theY direction (λ_Y ≠ 0 andλ_X =λ_Z = 0), the relative error between ΔK_Y and its first-order term is the same as that of theX direction and is therefore not shown. Third, if the displacement occurs in theZ direction (λ_Z ≠ 0 andλ_X =λ_Y = 0), the relative error between ΔK_Z and its first-order term is 0.22% and 0.88% atλ_Z = 0.1 and 0.2, respectively (Figure 4b).

The complex case is that the ball has a small displacement in all three axis directions, assuming that the eccentricity of the ball

ρ = \sqrt{λ_{X}^{2} + λ_{Y}^{2} + λ_{Z}^{2}}

is within the range of 0 ≤ρ ≤ 1.Figure 5 presents the comparison between ΔK_X and its first-order term atρ = 0.1 andρ = 0.2, respectively.The difference between ΔK_X and its first-order term (i.e., third-order terms) is also included. Two observations can be made. First, ΔK_X is roughly equal to its first-order term on the condition of a small eccentric displacement of the ball. Specifically,the relative error between ΔK_Z and its first-order term is less than 1% and 4% atρ = 0.1 and 0.2, respectively. Second, ΔK_X exhibits a linear dependence onλ_X, whereas the effect ofλ_Y andλ_Z on ΔK_X is negligible. Similarly, the corresponding conclusions for ΔK_Y and ΔK_Z can be inferred, respectively.

The above discussions indicate that the third-order terms of the eccentric displacements have little influence on the differential capacitance of the sensor if the eccentricity of the ballρ ≤ 0.2. In addition, it is reasonable to use a linear function to describe the relationship between the differential capacitance and the spatially eccentric displacement component. Hence, if the eccentric displacement componentsδ_X,δ_Y andδ_Z vary within a small range, Equations (17)–(19) can be rewritten in the following form:

Δ C_{X} = \frac{2.3896 ε R_{0}^{2}}{e_{0}^{2}} δ_{X},

(23)

Δ C_{Y} = \frac{2.3896 ε R_{0}^{2}}{e_{0}^{2}} δ_{Y},

(24)

Δ C_{Z} = \frac{1.6040 ε R_{0}^{2}}{e_{0}^{2}} δ_{Z} .

(25)

4. Simulation Setup

In practical applications, capacitive sensor plates have a certain thickness and a limited structure size. There are many charges unevenly distributed on each surface, and the density of the charges is much greater at the edge or tip end. Moreover, the electric field lines at the edge of the plate diverge outwards, resulting in the “fringe effect”. Therefore, the capacitance of the capacitive sensor is inevitably affected by the fringe effect [17]. The fringe effect not only decreases the sensitivity of capacitive sensor, but also generates nonlinear output which affects measuring accuracy. To reduce the errors caused by the fringe effect, equipotential guard rings are widely used in the design of capacitive sensors with spacing variation [18]. Therefore, guard rings (E_gr inFigure 6) for the proposed SDCS were designed on the periphery of the spherical capacitive plates. The radius of both inner and outer surfaces was equal to that of the spherical capacitive plates.

Ansoft Maxwell software was used to calculate the capacitance value at different eccentric displacements for the SDCS with and without guard rings. The spherical capacitive plates had an inner radius of 25.5 mm and a thickness of 2 mm. The radius of the ball was 25 mm, and other structural parameters of the SDCS are presented inTable 2. Abrasion-resistant material was used to fill in the gap between the ball and the spherical capacitive plates. However, air exited through the gap due to the assembly clearance. In order to simplify the simulation model and theoretical calculation, air was adopted as the dielectric. The permittivity of the air was 1.00053. The displacement varied from −50 μm to 50 μm, with a step of 2 μm.

5. Results and Discussions

5.1. Effect of Guard Rings

Figure 7 presents the simulated capacitance values of the spherical capacitorC₁ at different eccentric displacements, along with the theoretical results. Essential comparisons were made between the cases with and without guard rings. Two observations were made. First, the simulation capacitance values were larger than the theoretical values, which were mainly attributed to the fringe effect. This is consistent with Weng and Jin [19], that is, the fringe effect could lead to an increase in capacitance. Second, the increased capacitance was effectively reduced with guard rings, suggesting that the fringe effect could be weakened by deploying guard rings.

5.2. Dependence of the Differential Capacitances on the Eccentric Displacements

In this section, the dependence of the differential capacitances on the eccentric displacements is investigated in detail. To facilitate the discussion, the spatially eccentric displacement of the ball is divided into two categories based on the eccentric directions, namely, one along the single-axis direction and the other along the non-axis direction.

The simplest case is that the ball exhibits eccentric displacements in one of three orthogonal axes (i.e.,X,Y orZ direction). The authors have selected the eccentric displacements along theX directionδ_X as an example.δ_X varies from −50 μm to 50 μm, with a step of 2 μm. Evidently, the eccentricity of the ball is less than 0.1.Figure 8 presents the dependence of the differential capacitance ΔC_X, ΔC_Y and ΔC_Z on the displacements along theX directionδ_X. Three observations can be made. First, the variation of the simulated values of ΔC_X, ΔC_Y and ΔC_Z exhibits similar trends with that of the theoretical values. In other words, the simulation values are consistent with the theoretical values. Second, the differential capacitance ΔC_X exhibits a linear relationship with the displacementδ_X, suggesting a good linearity of the proposed sensor. Third, the simulated values of ΔC_Y or ΔC_Z are close to the theoretical values, that is, 0 pF over the range of −50 μm ≤δ_X ≤ 50 μm. This indicates that no displacement of the ball occurs along theY orZ direction. The simulated values exhibit small deviations of 0.5 pF in ΔC_Y and 0.4 pF in ΔC_Z from the theoretical values, which may be ascribed to the simulation errors.

Figure 9 andFigure 10 present the simulated values of the differential capacitances ΔC_X, ΔC_Y, and ΔC_Z on the condition that the eccentric displacements are along non-axis directions, the former being along the direction ofX =Y in theXOY plane (δ_X =δ_Y andδ_Z = 0) and the latter being along the direction ofX =Y = Z in three-dimensional (3D) space (δ_X =δ_Y =δ_Z). The maximum eccentricity is 0.14 for the eccentric displacements in theXOY plane and 0.17 for those in space, respectively. Several observations can be made. First, the simulated values of ΔC_X, ΔC_Y and ΔC_Z are roughly equal to their theoretical values. Second, if the eccentric displacements are along the direction ofX =Y in theXOY plane, both ΔC_X and ΔC_Y exhibit a linear correlation withδ_x, whereas the variation of ΔC_Z over the range of −50 μm ≤δ_X ≤ 50 μm approximately remains unchanged (Figure 9). Third, if the eccentric displacements are along the direction ofX =Y = Z in 3D space, all the differential capacitances ΔC_X, ΔC_Y and ΔC_Z show a linear relationship withδ_X (Figure 10). Finally, the gradient of ΔC_Z is lower than that of ΔC_X and ΔC_Y. This indicates that the sensitivity along theZ direction is lower than that along theX andY directions, which is consistent with Equations (23)–(25).

In summary, it can be inferred from the simulation result that the eccentric displacement component along theX,Y orZ direction has a good linear relationship with corresponding differential capacitance, provided that the eccentricity of the ball is small. Furthermore, due to the symmetrically spatial layout of the spherical capacitive plates and the differential calculation for the capacitance of the spherical capacitors, additional capacitance caused by the fringe effect can be effectively reduced.

6. Conclusions

This work proposes a novel method for the micro-clearance measurement of a precision spherical joint based on an SDCS. The configuration of the SDCS was first designed and a mathematical model of the proposed measurement method was then deduced. Finally, a simulation using Ansoft Maxwell software was conducted to verify the feasibility of the proposed method. The following conclusions can be made.

(1) The developed SDCS included a ball and eight spherical capacitive plates that were fixed onto the inner side of the socket. The ball was deployed as an excitation electrode, whereas each of the eight capacitive plates was used as a sensing electrode. As such, each capacitive plate and the ball formed a capacitor. The eccentric displacements of the ball were obtained by detecting the capacitance of eight spherical capacitors.

(2) A mathematical model of the differential capacitances and eccentric displacements was deduced. Due to the symmetrically spatial layout of the spherical capacitive plates and the differential calculation for the capacitance of the spherical capacitors, the even-order terms of dimensionless eccentric displacements of the ball in the socket were eliminated. Furthermore,if the eccentricity of the ball was less than 0.2, the third-order terms of the eccentric displacements had little effect on the differential capacitance of the sensor and were therefore neglected. As such, the differential capacitances ΔC_X, ΔC_Y and ΔC_Z exhibited a linear correlation with the eccentric displacement componentsδ_X,δ_Y andδ_Z, respectively.

(3) The simulated values approximately coincided with the theoretical values, showing a linear correlation between the differential capacitances ΔC_X, ΔC_Y and ΔC_Z and the eccentric displacements. This suggests the feasibility of the proposed method for the clearance measurement of a spherical joint. Moreover, the simulated values with guard rings are closer to the theoretical values than those without guard rings. This indicates that the capacitance derivation caused by the fringe effect can be effectively reduced by employing guard rings, that is, the measurement accuracy can be improved by deploying guard rings.

Thus, this work presents analytical and numerical investigations on a capacitive sensor for the clearance measurement of spherical joints. Further studies are still required on experimental investigations about the performance of an actual sensor. Moreover, the sensor performance may be affected by geometrical tolerances (e.g., spherical tolerances of the ball and symmetrical tolerances of the capacitive plates). Extensive studies are required to assess a specification on needed tolerances and to compare it with typical spherical joint tolerances. Finally, mathematical deductions using Pade approximation and Schwarz–Chistoffel mapping may be also interesting objectives of further studies that aim at improving the prediction or theoretical calculation of sensor performance.

Author Contributions

Conceptualization, W.W.; Methodology, W.W. and K.L.; Numerical Simulation, M.Z. and K.X.; Data Analysis, M.Z. and G.S.; Writing—Original Draft Preparation, M.Z. and H.Y.; Writing—Review and Editing, H.Y., Z.C. and W.W.; Supervision, W.W. and B.J.; Funding Acquisition, W.W. and B.J. All authors regularly discussed the progress during the entire work.

Funding

This research was supported by the Zhejiang Provincial Natural Science Foundation of China under Grant No. LZ16E050001, and the National Natural Science Foundation of China under Grant Nos. U1709206, 51465027, and 51275465.

Conflicts of Interest

The authors declare no conflict of interest.

References

Robertson, A.P.; Slocum, A.H. Measurement and characterization of precision spherical joints.Precis. Eng.2006,30, 1–12. [Google Scholar] [CrossRef]
Zhu, J.; Ting, K.L. Uncertainty analysis of planar and spatial robots with joint clearances.Mech. Mach. Theory2000,35, 1239–1256. [Google Scholar] [CrossRef]
Han, Y.; Zhong, C.; Zhu, X.; Zhe, J. Online monitoring of dynamic tip clearance of turbine blades in high temperature environments.Meas. Sci. Technol.2018,29, 045102. [Google Scholar] [CrossRef] [Green Version]
Garcia, I.; Przysowa, R.; Amorebieta, J.; Zubia, J. Tip-clearance measurement in the first stage of the compressor of an aircraft engine.Sensors2016,16, 1897. [Google Scholar] [CrossRef] [PubMed]
Zhang, J.; Duan, F.; Niu, G.; Jiang, J.; Li, J. A blade tip timing method based on a microwave sensor.Sensors2017,17, 1097. [Google Scholar] [CrossRef] [PubMed]
Jamia, N.; Friswell, M.I.; El-Borgi, S.; Fernandes, R. Simulating eddy current sensor outputs for blade tip timing.Adv. Mech. Eng.2018,10, 1–12. [Google Scholar] [CrossRef]
Lawson, C.P.; Ivey, P.C. Tubomachinery blade vibration amplitude measurement through tip timing with capacitance tip clearance probes.Sens. Actuators A Phys.2005,118, 14–24. [Google Scholar] [CrossRef]
Endemano, A.; Desmulliez, M.P.Y.; Dunnigan, M. System level simulation of a double stator wobble electrostatic micromotor.Sens. Actuators A Phys.2002,99, 312–320. [Google Scholar] [CrossRef]
Han, F.T.; Gao, Z.Y.; Li, D.M.; Wang, Y.L. Nonlinear compensation of active electrostatic bearings supporting a spherical rotor.Sens. Actuators A Phys.2005,119, 177–186. [Google Scholar] [CrossRef]
Han, F.T.; Gao, Z.Y.; Wang, Y.L. Modelling and linearization for long-range spherical gap measurement.Chin. J. Sci. Instrum.2002,23, 257–260. (In Chinese) [Google Scholar] [CrossRef]
Gao, Z.Y.Electrostatically Suspended Gyroscope Technology; Tsinghua University Press: Beijing, China, 2004; ISBN 9787302087786. (In Chinese) [Google Scholar]
Hill, D.A.; Letendre, T.; Mills, H.A. Embedded, real-time DSP control of an electrostatically suspended gyroscope. In Proceedings of the 2004 American Control Conference, Boston, MA, USA, 30 June–2 July 2004; Volume 4, pp. 3321–3326. [Google Scholar]
Liu, J.H.; Wang, H.; Chang, K.; Li, X.; Wang, Q.L. Design and test of displacement transducer for an electrode-insulated electrostatically suspended gyroscope. In Proceedings of the 2015 IEEE International Conference on Applied Superconductivity and Electromagnetic Devices, Shanghai, China, 20–23 November 2015; pp. 429–430. [Google Scholar]
Han, F.T.; Wu, Q.P.; Gao, Z.Y. Initial levitation of an electrostatic bearing system without bias.Sens. Actuators A Phys.2006,130–131, 513–522. [Google Scholar] [CrossRef]
Baxter, L.K.Capacitive Sensors: Design and Applications; IEEE Press: New York, NY, USA, 1997; ISBN 9780780353510. [Google Scholar]
Heerens, W.C. Application of capacitance techniques in sensor design.J. Phys. E Sci. Instrum.1986,19, 897–906. [Google Scholar] [CrossRef]
Wang, W.; Wen, Y.H.; Yu, J.P.; Chen, Z. Impact of fringe effect on measuring accuracy of planar capacitive sensors.Sens. Lett.2011,9, 1458–1461. [Google Scholar] [CrossRef]
Ma, Y.Z.; Yu, Y.X.; Wang, X.H. Key technique for inner hole diameter measure with capacitive probe.Appl. Mech. Mater.2013,303–306, 827–830. [Google Scholar] [CrossRef]
Weng, C.W.; Jin, A.K. Effect of fringing fields on the capacitance of circular microsrip disk.IEEE Trans. Microw. Theory1980,28, 98–104. [Google Scholar] [CrossRef]

Figure 1. Structural model of the proposed SDCS: (a) assembly diagram and (b) distribution of the spherical capacitive plates.

Figure 2. Schematic diagram of the spherical clearance calculation.

Figure 3. Coordinate system with a spherical capacitive plateCE_s1.

Figure 4. First-order term and the sum of four terms of (a) ΔK_X and (b)ΔK_Z if the displacements occur along the single-axis direction.

Figure 5. Sum of four terms, first-order term and third-order terms of ΔK_X with (a)ρ = 0.1 and (b)ρ = 0.2 if the displacements occur along the non-axis direction.

Figure 6. Simulation model of the SDCS with guard rings.

Figure 7. Effect of the guard rings on the capacitance value of the spherical capacitorC₁.

Figure 8. Relationship between the differential capacitance values and the displacements in the case ofδ_Y =δ_Z = 0: (a) ΔC_X, (b) ΔC_Y and (c) ΔC_Z.

Figure 9. Relationship between the differential capacitance values and the displacements in the case ofδ_X =δ_Y andδ_Z = 0: (a) ΔC_X, (b) ΔC_Y and (c) ΔC_Z.

Figure 10. Relationship between the differential capacitance values and the displacements in the case ofδ_X =δ_Y =δ_Z: (a) ΔC_X, (b) ΔC_Y and (c) ΔC_Z.

Table 1. Spherical capacitors included in three pairs of differential capacitance units alongX,Y andZ directions, respectively.

Unit Pair	Capacitors for Unit 1	Capacitors for Unit 2
C_up-X	C₁,C₄,C₅ andC₈	C₂,C₃,C₆ andC₇
C_up-Y	C₁,C₂,C₅ andC₆	C₃,C₄,C₇ andC₈
C_up-Z	C₁,C₂,C₃ andC₄	C₅,C₆,C₇ andC₈

Table 2. Simulation parameters of the SDCS.

Parameters	Values
The angle of spherical capacitive plates in the longitude directionζ	π/6
The angle of spherical capacitive plates in the latitude directionξ	π/3
The angle of the clearance between the guard ringη	π/90

© 2018 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).

Share and Cite

MDPI and ACS Style

Wang, W.; Yang, H.; Zhang, M.; Chen, Z.; Shi, G.; Lu, K.; Xiang, K.; Ju, B. A Novel Method for the Micro-Clearance Measurement of a Precision Spherical Joint Based on a Spherical Differential Capacitive Sensor.Sensors2018,18, 3366. https://doi.org/10.3390/s18103366

AMA Style

Wang W, Yang H, Zhang M, Chen Z, Shi G, Lu K, Xiang K, Ju B. A Novel Method for the Micro-Clearance Measurement of a Precision Spherical Joint Based on a Spherical Differential Capacitive Sensor.Sensors. 2018; 18(10):3366. https://doi.org/10.3390/s18103366

Chicago/Turabian Style

Wang, Wen, He Yang, Min Zhang, Zhanfeng Chen, Guang Shi, Keqing Lu, Kui Xiang, and Bingfeng Ju. 2018. "A Novel Method for the Micro-Clearance Measurement of a Precision Spherical Joint Based on a Spherical Differential Capacitive Sensor"Sensors 18, no. 10: 3366. https://doi.org/10.3390/s18103366

APA Style

Wang, W., Yang, H., Zhang, M., Chen, Z., Shi, G., Lu, K., Xiang, K., & Ju, B. (2018). A Novel Method for the Micro-Clearance Measurement of a Precision Spherical Joint Based on a Spherical Differential Capacitive Sensor.Sensors,18(10), 3366. https://doi.org/10.3390/s18103366

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further detailshere.

Article Metrics

Article Access Statistics

For more information on the journal statistics, clickhere.

Multiple requests from the same IP address are counted as one view.

Movatterモバイル変換

Article Menu

A Novel Method for the Micro-Clearance Measurement of a Precision Spherical Joint Based on a Spherical Differential Capacitive Sensor

Abstract

1. Introduction

2. Structural Design and Measuring Principle

3. Mathematical Model

3.1. Calculation of the Clearance between the Ball and the Spherical Capacitive Plates

3.2. Relation between Capacitance of Spherical Capacitors and Eccentric Displacements

4. Simulation Setup

5. Results and Discussions

5.1. Effect of Guard Rings

5.2. Dependence of the Differential Capacitances on the Eccentric Displacements

6. Conclusions

Author Contributions

Funding

Conflicts of Interest

References

Share and Cite

Article Metrics

Article Access Statistics

Further Information

Guidelines

MDPI Initiatives

Follow MDPI