 | This articleneeds additional citations forverification. Please helpimprove this article byadding citations to reliable sources. Unsourced material may be challenged and removed. Find sources: "Rover K-series engine" – news ·newspapers ·books ·scholar ·JSTOR(September 2007) (Learn how and when to remove this message) |
| Rover K-series | |
|---|---|
 | |
| Overview | |
| Manufacturer | Rover Group MG Rover Group/Powertrain Ltd |
| Production | 1988–2005 (K series) |
| Layout | |
| Configuration | Straight-4 |
| Displacement | 1.1 to 1.8 L; 67.9 to 109.6 cu in (1,113 to 1,796 cc) |
| Cylinder bore | 80 mm (3.15 in) |
| Piston stroke | 89.3 mm (3.52 in) |
| Cylinder block material | Aluminium |
| Cylinder head material | Aluminium |
| Valvetrain | SOHC 2 valves x cyl. DOHC4 valves x cyl. withVVC |
| RPM range | |
| Max. engine speed | 7200 |
| Combustion | |
| Turbocharger | On some versions |
| Fuel system | Single KIFSU Carburettor Fuel injection |
| Management | Rover MEMS |
| Fuel type | Petrol |
| Oil system | Wet sump |
| Cooling system | Water-cooled |
| Output | |
| Power output | 60–192 PS (44–141 kW; 59–189 hp) |
| Torque output | 124–128 lb⋅ft (168–174 N⋅m) |
| Chronology | |
| Predecessor | |
| Successor | SAIC Kavachi engine |
TheRover K-series engine is a series ofinternal combustion engines built byPowertrain Ltd, a sister company ofMG Rover. The engine was astraight-four cylinder built in two forms,SOHC andDOHC, ranging from 1.1 to 1.8 L; 67.9 to 109.6 cu in (1,113 to 1,796 cc).
The K series was introduced in 1988 byRover Group as a powerplant for theRover 200 car. It was the second volume-production implementation of the low-pressure sand-casting (or LPS) technique in a new plant sited between East Works andCofton Hackett. (The first volume application of the LPS process had been for theM-16 cylinder head, produced in South Works, adjacent to the former forge). The LPS process pumped liquid aluminium into a chemically-bonded sand mould from below. This reduced oxide inclusions and gave a casting yield of around 90%, compared with 60% for more conventional gravity casting processes. The process avoided many of the inherent problems of casting aluminium components and consequently permitted lower casting wall thickness and higher strength-to-weight ratios. However, the process required the use of heat-treated LM25 material which gave the engines a reputation for being fragile. An engine overheat would often result in the material becoming annealed and rendering the components scrap. The layout of the engine bay on some Rover cars fitted with K-series engines – particularly the MGF with its mid-engined layout – means that a commonly-occurring coolant leak under the inlet manifold can go undetected until severe damage has been done to the head. The aluminium engine blocks were fitted withspun-cast ironcylinder liners that were initially manufactured byGKN's Sheepbridge Stokes ofChesterfield, but these were replaced by liners made by Goetze. Unfortunately a large number of aftermarket engines, the so-called "VHPDs", were built with the old substandard GKN liners by Minister, Lotus and PTP well after the introduction of the Goetze liners to production in 2000.
The engine was introduced initially in 1.1-litresingle overhead cam and 1.4-litredual overhead cam versions. Because Honda stopped providing Rover with engines after the end of their relationship, but well before the BMW takeover, an enlargement of the K Series design to 1.6 and 1.8 litres was carried out. This was done by using larger diameter cylinder liners and also increasing the stroke. The change required a block redesign with the removal of the cylinder block's top deck and a change from "wet" liners to "damp" liners.[1] The plastic throttle body fitted to the engine until 2001 was manufactured by theSU Carburettor company. They also included aluminium and larger sized bodies.
The four-cylinder engines were held together as a sandwich of components bylong through-bolts which held the engine under compression, though this construction is not unknown, and was used in early lightweight fighter engines from theFirst World War. It had also been used in motorcycle engines and Triumph's "Sabrina" Le Mans race engine.[2][3]
The two types of head that were bolted to the common four-cylinder block were designated K8 (8 valves) and K16 (16 valves). A later head design also incorporated a Rover-designedVariable Valve Control (VVC) unit (derived from an expired AP patent). This allowed more power to be developed without compromising low-speed torque and flexibility. The VVC system constantly alters the inlet cam period, resulting in a remarkably flexible drive: the torque curve of a VVC K-series engine is virtually flat throughout the rev range and power climbs steadily with no fall-off whatsoever until the rev limiter kicks in at 7,200 rpm.[citation needed]
Following the collapse ofMG Rover Group in 2005, the K Series engine started a new and rather interesting chapter in its history.Two separate re-developments of the engine were taking place by at the time two rival Chinese car firms.[citation needed]
The Chinese automakerNanjing Automobile (NAC) purchased the assets of MG Rover and in doing so acquired use of theLongbridge plant and the intellectual property rights and production tooling to many designs, including those of the K series engine.[citation needed]
With the help of Lotus Engineering, NAC went on to produce the N Series an improved version of the K Series with redesigned headgasket and oil rail built on the original tooling.[citation needed]
This engine featured in the relaunched MG TF in the UK and the MG3 SW and MG7 in China. Contrary to popular belief, the N Series was never fitted to theMG 6.[citation needed]
When the MG TF ceased production for the final time in 2011, so did the N Series.[citation needed]
The second development was by the larger Chinese conglomerateSAIC Motor. SAIC had also previously purchased the rights and blueprints to several of MG Rovers designs. Whilst they had the necessary know-how they didn't have any tooling so had to essentially reverse engineer their version of the engine.[citation needed]
The advantage of this was it allowed Ricardo 2010, the company tasked by SAIC to carry out development the opportunity to improve the engine in a number of areas.[citation needed]
The main areas of improvement included the head being redesigned to improve the waterways and structural rigidity and the block was also strengthened.[citation needed]
All new tooling was used in its production and the quality of materials and that of the aluminium casting process created a much more substantial update than that of the N Series.[citation needed]
This new engine would go on to power the Roewe 750, the Roewe 550 and later after the two firms NAC and SAIC merged, TheMG 6.[citation needed]
Early K8 engines used a single SU KIFcarburetor with a manual choke and a breaker-lessdistributor mounted on the end of thecamshaft. MEMSSingle-point injection became standard with the launch of the Rover 100 in 1994.
K16 models usedMEMS, with a 1.6ECU from 1990 until 1994 and a 1.9 ECU from 1995 onwards, in either Single Point orMulti Point forms, with a single coil on the back of the engine block and a distributor cap and rotor arm on the end of the inlet camshaft. MEMS 2J was used on the VVC engine, to control the Variable Valve Control and theDistributorless Ignition System, which was used because there were camshaftdrive belts at both ends of the engine. With the launch of theRover 25 andRover 45 in 1999, MEMS 3 was introduced, with twin coils andsequential injection.
| This sectiondoes notcite anysources. Please helpimprove this section byadding citations to reliable sources. Unsourced material may be challenged andremoved.(September 2023) (Learn how and when to remove this message) |
.jpg)
All1100 engines displace 1.1 L; 67.9 cu in (1,113 cc) with bore X stroke of 75 mm × 63 mm. Four variations were created:
Cars that came with the 1100:
Engine Codes: 14K2F (8V), 14K4F (16V), 14K16 (16V)?
All1400 engines displace 1.4 L; 85.2 cu in (1,396 cc) with bore X stroke of 75 mm × 79 mm (2.95 in × 3.11 in) and have DOHC, 16 valves and MPI. Six variations were created:
The K16 82 hp (61 kW; 83 PS) variant is exactly the same as the 103 PS (76 kW; 102 hp) version, apart from a restrictive throttle body designed to lower the car's insurance group. This can be converted to the 103 hp (77 kW) model by changing to the unrestricted throttle body of a 103 engine. The 90 PS (66 kW; 89 hp) Spi features single-point fuel injection rather than the multi-point of the later engine.
Cars that came with the 1400:
Engine Code: 16K4F
All1600 engines displace 1.6 L; 96.9 cu in (1,588 cc) with bore X stroke of 80 mm × 79 mm (3.15 in × 3.11 in) and have DOHC, 16 valves and MPI. Two variations were created:
Cars that came with the 1600:
Engine Codes: 18K4F (16V non-VVC), 18K4K (VVC variants)
The 1.8 engine is the largest the engine displaces. All1800 engines displace 1.8 L; 109.6 cu in (1,796 cc) with bore X stroke of 80 mm × 89.3 mm (3.15 in × 3.52 in)DOHC4 valves per cylinder andMPI.
Non-VVC (18K4F):
Naturally Aspirated:
The base engine makes 118 bhp (120 PS; 88 kW) @ 5600 rpm and 124 lb⋅ft (168 N⋅m) @ 3500 rpm oftorque or in slightly tuned at 136 PS (100 kW; 134 hp) @ 6750 rpm/ 165 N⋅m (122 lb⋅ft) @ 3000 rpm in the MG TF
| Years | Model |
|---|---|
| 1995-99 | Rover 200 |
| 1999-05 | Rover 25 |
| 1999-05 | Rover 45 |
| 1998-05 | Rover 75 |
| 2003–05 | Rover Streetwise |
| 2001-05 | MG ZR |
| 2001-05 | MG ZS |
| 2001-05 | MG ZT |
| 1995–05 | MG F |
| 1997–06 | Land Rover Freelander |
| 1996-05 | Caterham Seven |
| 1996–99 | Caterham 21 |
Turbocharged:
The 1.8 Turbo was developed to replace the 2.0Rover KV6 engine due to emissions and fuel economy, the engine isturbocharged and made 150 to 160 PS (110 to 118 kW; 148 to 158 hp)
VVC (18K4K):
The VVC engine came in three variant:
| Years | Model |
|---|---|
| 1995-99 | Rover 200 |
| 1995-99 | Rover 200 Coupe |
| 1999-05 | Rover 25 |
| 1995–05 | MG F / MG TF |
| 1996-05 | Caterham Seven |
| 1996–99 | Caterham 21 |
| Years | Model |
|---|---|
| 2001-05 | MG ZR |
| 2001-05 | MG ZS |
| 2001-05 | MG ZT |
| 1995–05 | MG F / MG TF |
| 1996-05 | Caterham Seven |
| 1996–99 | Caterham 21 |
| Years | Model |
|---|---|
| 1996-06 | Lotus Elise |
| 2000-04 | Lotus Exige |
| 2000 | Lotus 340R |
| 1996-05 | Caterham Seven |
| 1996–99 | Caterham 21 |
The SAIC Kavachi engine is an extensively improved version of the Rover K series, using a different turbo and gearbox, improved head gasket and strengthened block. UK engineering firm Ricardo plc, expert in race engine designs, was commissioned to not only redesign the engine but also the manufacturing process to produce what is now a very reliable engine. It is only available in 1.8 L; 109.6 cu in (1,796 cc) version.