Kodi can natively mount SMB, NFS, SFTP, WebDAV (and more) remote filesystems (shares) to read media for playback, but many applications that write content, e.g. TVHeadend storing TV recordings, must write to "local" storage. Remote SMB and NFS shares can be "mounted" to the local filesystem using kernel mounts configured through systemd .mount files.

The following NAS configuration is used in the examples below:

• NAS IP:192.168.1.222

• Username:nasuser1

• Password:123nas

• Share name:recordings

• Full address to share:\\192.168.1.222\recordings

SMB Shares

1. Create the folder where the share should be mounted

Connect to your LibreELEC HTPC with SSH.

mkdir /storage/recordings

2. Create the systemd .mount file

IMPORTANT: The filename uses hyphens to separate elements of the filesystem path to the share mount-point, e.g./storage/recordings will bestorage-recordings.mount and sub folders, e.g./storage/recordings/tv would bestorage-recordings-tv.mount

Create the .mount file:

nano /storage/.config/system.d/storage-recordings.mount

Below is an example of the mount definition file for a Samba share:

[Unit]Description=cifs mount scriptRequires=network-online.serviceAfter=network-online.serviceBefore=kodi.service[Mount]What=//192.168.1.222/recordingsWhere=/storage/recordingsOptions=username=nasuser1,password=123nas,rw,vers=2.1Type=cifs[Install]WantedBy=multi-user.target

3. Things to edit

Address of your share. Remember to always use / slashes:

What=//192.168.1.222/recordings

Path where the Share should be mounted:

Where=/storage/recordings

Options:

Options=username=nasuser1,password=123nas,rw,vers=2.1

4. Enable the mount

Finally we need to enable the mountpoint.

systemctl enable storage-recordings.mount

5. Reboot

Reboot your system to check if the mount works.

6. Helpful command for troubleshooting

Get status and error messages from the mount point:

systemctl status storage-recordings.mount

Remove mount point and disable it:

systemctl disable storage-recordings.mount

NFS Shares

1. Create the folder where the share should be mounted

mkdir /storage/recordings

2. Create the systemd definition file

Important: you need to set the filename for the definition file according to the folder where you want to mount your share . In our case:storage-recordings.mount represents the path ->/storage/recordings. If you add a subfolder:storage-recordings-tv.mount represents the path ->/storage/recordings/tv.

nano /storage/.config/system.d/storage-recordings.mount

Contents of the definition file for a NFS share:

[Unit]Description=test nfs mount scriptRequires=network-online.serviceAfter=network-online.serviceBefore=kodi.service[Mount]What=192.168.1.222:/usr/data2/videoWhere=/storage/recordingsOptions=Type=nfs[Install]WantedBy=multi-user.target

3. Things to edit

Address of your share;

What=192.168.1.222:/usr/data2/video

Path where the share should be mounted:

Where=/storage/recordings

Options: At this section you are able to define specific NFS options, such as the NFS version. In the example below we set Type for an NFSv3 share.

Type=nfs

To use an NFSv4 share:

Type=nfs4

4. Start it for a test

systemctl start storage-recordings.mount

Note: That's only a test and the mount won't be available after a reboot. To make it available after boot you have to "enable" the service first.

5. Enable the mount

If the previous test worked, enable the service via:

systemctl enable storage-recordings.mount

6. Reboot

Reboot your system to see if the mount is available after boot.

7. Helpful commands for troubleshooting

Get status and error messages from the mount point:

systemctl status storage-recordings.mount

Remove mount point and disable it:

systemctl disable storage-recordings.mount

Apple TimeCapsule

TimeCapsule devices share files using an Apple dialect of SMB that is not compatible with the Sambasmbclient Kodi uses to connect to SMB shares. To access media on a TimeCapsule you can follow the steps described above for connecting to Samba shares with a systemd storage mount, but with one difference: theOptions configuration must force SMB v1.0 and legacy NTLM authentication or the mount will fail. See below:

Options=username=MyUser,password=MyPass,sec=ntlm,vers=1.0

SMB v1.0 is widely considered to be insecure, but TimeCapsules no longer receive software updates and there is no alternative; SMB v2/v3 are not supported.

Auto Mounting

In some edge cases where the remote filesystem may be unavailable when LibreElec boots or the remote filesystem has a chance of disconnecting, an automount is an easy way to mount without the risk of failure and with the option to attempt to connect/reconnect with no extra effort.

It is basically a safe way to retry mounting the remote filesystem.

How it works

Because we enable the automount service, we can disable the mount service. Which in turn allows the system to boot without errors, even if the network share is not available (it will still show the files as missing until the share is available, but this is expected). What the automount does is try to connect to the network share when the local mount path is accessed by the filesystem. So when trying to play media from the mount path, or trying to update the library (assuming the mount path is in your media library).

1. Create the folder and systemd.mount definition file

Follow the relevant instructions above to create a systemd.mount definition file for your network share.

IMPORTANT: It is recommened to follow the instructions above completey and add the mounted path to your library in Kodi before proceeding with the instructions below.

2. Disable the mount service in systemd

If you've already enabled the mount service in systemd, disable it to prevent errors on boot when the network share is unavailable.

systemctl disable storage-recordings.mount

3. Create a systemd.automount definition file

Filename restrictions are the same as for the.mount definition file. Meaning that if your.mount file is namedstorage-recordings.mount your automount file should be namedstorage-recordings.automount.

nano /storage/.config/system.d/storage-recordings.automount

Contents of the automount definition file:

[Unit]Description=test automount for recordings[Automount]Where=/storage/recordingsTimeoutIdleSec=0[Install]WantedBy=multi-user.target

4. Things to edit

Path of the mount in question:

Where=/storage/recordings

Idle timeout (time before systemd should unmount the network share, 0 means disabled):

TimeoutIdleSec=0

5. Enable the automount service

systemctl enable storage-recordings.automount

6. Reload systemd to apply changes

systemctl daemon-reload

7. Test the automount

If you have already added the mount path to your library in Kodi, you can test the automount by trying to access the folder inside Kodi. If all went well, the network share will mount as soon as you attempt to access it's mount path.

If the network share is available when LibreElec is starting up, it will be mounted during the boot process.

8. Helpful commands for troubleshooting

Get status and error messages from the automount (great for seeing when a mount was attempted):

systemctl status storage-recordings.automount

IMPORTANT: Running the above command will NOT show mount errors, to see mount errors you will still need to runsystemctl status on the.mount service (systemctl status storage-recordings.mount).

Disable the automount:

systemctl disable storage-recordings.automount

Last updated12 months ago