Movatterモバイル変換

ROUTE(8)              Linux System Administrator's ManualROUTE(8)NAME       route - show / manipulate the IP routing tableSYNOPSIS       route [-CFvnNee] [-A family |-4|-6]       route  [-v] [-A family |-4|-6] add [-net|-host] target [netmask Nm] [gw              Gw] [metric N] [mss M] [window W] [irtt I] [reject] [mod]  [dyn]              [reinstate] [[dev] If]       route  [-v] [-A family |-4|-6] del [-net|-host] target [gw Gw] [netmask              Nm] [metric M] [[dev] If]       route  [-V] [--version] [-h] [--help]DESCRIPTION       Route manipulates the kernel's IP routing tables.  Its primary  use  is       to  set up static routes to specific hosts or networks via an interface       after it has been configured with theifconfig(8) program.       When the add or del options are used, route modifies  the  routing  ta-       bles.   Without  these  options, route displays the current contents of       the routing tables.OPTIONS       -A family              use the specified address family (eg `inet'). Use  route  --help              for  a  full list. You can use -6 as an alias for --inet6 and -4              as an alias for -A inet       -F     operate on the kernel's FIB (Forwarding Information Base)  rout-              ing table.  This is the default.       -C     operate on the kernel's routing cache.       -v     select verbose operation.       -n     show numerical addresses instead of trying to determine symbolic              host names. This is useful if you are trying  to  determine  why              the route to your nameserver has vanished.       -e     usenetstat(8)-format  for  displaying  the routing table.  -ee              will generate a very long line  with  all  parameters  from  the              routing table.       del    delete a route.       add    add a new route.       target the destination network or host. You can provide an addresses or              symbolic network or host name. Optionally you can use /prefixlen              notation instead of using the netmask option.       -net   the target is a network.       -host  the target is a host.       netmask NM              when adding a network route, the netmask to be used.       gw GW  route packets via a gateway.              NOTE:  The  specified gateway must be reachable first. This usu-              ally means that you have to set up a static route to the gateway              beforehand.  If you specify the address of one of your local in-              terfaces, it will be used to decide about the interface to which              the  packets should be routed to. This is a BSDism compatibility              hack.       metric M              set the metric field in the routing table (used by routing  dae-              mons) to M. If this option is not specified the metric for inet6              (IPv6) address family defaults to '1', for inet  (IPv4)  it  de-              faults  to  '0'.  You  should  always specify an explicit metric              value to not rely on those defaults  -  they  also  differ  from              iproute2.       mss M  sets  MTU  (Maximum  Transmission Unit) of the route to M bytes.              Note that the current implementation of the route  command  does              not allow the option to set the Maximum Segment Size (MSS).       window W              set  the  TCP  window  size for connections over this route to W              bytes. This is typically only used on AX.25  networks  and  with              drivers unable to handle back to back frames.       irtt I set  the initial round trip time (irtt) for TCP connections over              this route to I milliseconds (1-12000). This is  typically  only              used on AX.25 networks. If omitted the RFC 1122 default of 300ms              is used.       reject install a blocking route, which will force  a  route  lookup  to              fail.   This is for example used to mask out networks before us-              ing the default route. This is NOT for firewalling.       mod, dyn, reinstate              install a dynamic or modified route. These flags are  for  diag-              nostic purposes, and are generally only set by routing daemons.       dev If force  the  route to be associated with the specified device, as              the kernel will otherwise try to determine the device on its own              (by  checking already existing routes and device specifications,              and where the route is added to). In most  normal  networks  you              won't need this.              If  dev  If is the last option on the command line, the word dev              may be omitted, as it's the default. Otherwise the order of  the              route modifiers (metric netmask gw dev) doesn't matter.EXAMPLES       route add -net 127.0.0.0 netmask 255.0.0.0 metric 1024 dev lo              adds  the normal loopback entry, using netmask 255.0.0.0 and as-              sociated with the "lo" device (assuming this device  was  previ-              ously set up correctly withifconfig(8)).       route add -net 192.56.76.0 netmask 255.255.255.0 metric 1024 dev eth0              adds  a  route to the local network 192.56.76.x via "eth0".  The              word "dev" can be omitted here.       route del default              deletes the current default route, which is labeled "default" or              0.0.0.0 in the destination field of the current routing table.       route del -net 192.56.76.0 netmask 255.255.255.0              deletes the route. Since the Linux routing kernel uses classless              addressing, you pretty much always have to specify  the  netmask              that is same as as seen in 'route -n' listing.       route add default gw mango              adds  a  default  route  (which  will  be used if no other route              matches).  All  packets  using  this  route  will  be  gatewayed              through  the  address  of a node named "mango". The device which              will actually be used for that route depends on how we can reach              "mango" - "mango" must be on directly reachable route.       route add mango sl0              Adds  the route to the host named "mango" via the SLIP interface              (assuming that "mango" is the SLIP host).       route add -net 192.57.66.0 netmask 255.255.255.0 gw mango              This command adds the net "192.57.66.x" to be gatewayed  through              the former route to the SLIP interface.       route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0              This  is  an obscure one documented so people know how to do it.              This sets all of the class D (multicast) IP  routes  to  go  via              "eth0".  This  is  the  correct normal configuration line with a              multicasting kernel.       route add -net 10.0.0.0 netmask 255.0.0.0 metric 1024 reject              This  installs  a  rejecting  route  for  the  private   network              "10.x.x.x."       route -6 add 2001:0002::/48 metric 1 dev eth0              This  adds a IPv6 route with the specified metric to be directly              reachable via eth0.OUTPUT       The output of the kernel routing table is organized  in  the  following       columns       Destination              The destination network or destination host.       Gateway              The gateway address or '*' if none set.       Genmask              The  netmask  for  the  destination net; '255.255.255.255' for a              host destination and '0.0.0.0' for the default route.       Flags  Possible flags include              U (route is up)              H (target is a host)              G (use gateway)              R (reinstate route for dynamic routing)              D (dynamically installed by daemon or redirect)              M (modified from routing daemon or redirect)              A (installed by addrconf)              C (cache entry)              !  (reject route)       Metric The 'distance' to the target (usually counted in hops).       Ref    Number of references to this route. (Not used in the Linux  ker-              nel.)       Use    Count  of lookups for the route.  Depending on the use of -F and              -C this will be either route cache misses (-F) or hits (-C).       Iface  Interface to which packets for this route will be sent.       MSS    Default maximum segment  size  for  TCP  connections  over  this              route.       Window Default window size for TCP connections over this route.       irtt   Initial  RTT  (Round  Trip  Time). The kernel uses this to guess              about the best TCP protocol parameters without waiting on  (pos-              sibly slow) answers.       HH (cached only)              The  number  of  ARP entries and cached routes that refer to the              hardware header cache for the cached route. This will be -1 if a              hardware  address  is not needed for the interface of the cached              route (e.g. lo).       Arp (cached only)              Whether or not the hardware address for the cached route  is  up              to date.FILES       /proc/net/ipv6_route       /proc/net/route       /proc/net/rt_cacheSEE ALSOifconfig(8),netstat(8),arp(8),rarp(8),ip(8)HISTORY       Route  for  Linux  was  originally  written  by  Fred  N.   van Kempen,       <waltje@uwalt.nl.mugnet.org> and then modified by Johannes  Stille  and       Linus  Torvalds for pl15. Alan Cox added the mss and window options for       Linux 1.1.22. irtt support and merged with netstat  from  Bernd  Ecken-       fels.AUTHOR       Currently  maintained  by Phil Blundell <Philip.Blundell@pobox.com> and       Bernd Eckenfels <net-tools@lina.inka.de>.net-tools                         2014-02-17ROUTE(8)