AV4 engine is a four-cylinderpiston engine where the cylinders share a common crankshaft and are arranged in aV configuration.
The V4 engine is less common compared tostraight-four engines. However, V4 engines have been used in automobiles, motorcycles, and other applications.
Some V4 engines have twocrankpins that are shared by opposing cylinders. The crankshaft is usually supported by threemain bearings in this type of engines. However this arrangement results an uneven firing engine. Split crankpins are preferred for even firing intervals.
Compared to the more common inline-four engine layout, a V4 engine is much shorter. Although different V angles can be used, if the two pistons are at a 90° V-angle with shared crankpins, the engine also achieves a perfectprimary balance and offers the additional advantage of bettersecondary balance that reduces vibration.[1] The shorter crankshaft of the V4 engine is less susceptible to the effects oftorsional vibration due to its increased stiffness and also because of fewer supports suffers less friction losses.[citation needed]
Disadvantages of V4 engines include its design being inherently wider compared to inline-4 engines, as well as the requirement of two exhaust manifolds, two-cylinder heads, and two valvetrains (thus needing two sets of camshafts for overhead cam engines) rather than only one cylinder head, one manifold, one valvetrain, and one set of camshafts for an inline-four engine.[2] Having two separate banks of components increases cost and complexity in comparison with inline four engines.
Because V4 engines are wider than inline-four engines, incorporating auxiliary drives, inlet systems, and exhaust systems while maintaining an overall compact size may be more difficult like other V-type engines. In order to reduce width, a narrower V-angle could be utilized, such as 60 degrees. Although a 60° V4 is more compact than a 90° V4 engine, the 60° design does not have perfect primary balance (if the crankpins are not split) and, therefore, often require abalance shaft to reduce vibrations similar to theV6 engines. Additionally, any (four-stroke) V4 engine with shared crankpins willfire unevenly which will result in more vibration and potentially require a heavier flywheel. Using split crankpins in a 60° V4, as used on theFord Essex V4 engine andFord Taunus V4 engines, results in an even firing order.
.jpg)
The earliest automotive use of V4 engines were in Grand Prix racing (later called 'Formula One') cars. One of the pioneering V4 engines was in the 1898Mors rear-engined car built in France.[3][4] At the time, the lack of vibration from the V4 engine was a key selling point.[5] However, the car's V4 engine was replaced by a conventional inline-four engine by 1901.
In the1907 French Grand Prix, the car entered byJ. Walter Christie used a 19,891 cc (1,214 cu in) V4 engine, the largest engine ever used in a Grand Prix race.[6] The engine was mounted transversely in the front and the car was front-wheel drive. The car retired from the French Grand Prix after just four laps, however, it later set a speed record of 164 km/h (102 mph).[7]
The first V4 engine used in production cars was theLancia V4 engine that was first used in the 1922Lancia Lambda.[8] The Lancia engine was a narrow-angle design with an angle of 20 degrees between the banks and a single cylinder head with one overhead camshaft shared by both banks. It also usedaluminium for both the block and head (which was unusual for the time).[9] Lancia produced V4 engines until 1976, when they were replaced by flat-four engines.
The 1960–1994ZAZ Zaporozhets is a Soviet city-type car that used a rear-mounted V4 engine.[9] This engine was based on the design used in theLuAZ-967 amphibious military vehicle. It featured air-cooling with a magnesium block and was produced in displacements from 0.7–1.2 L (43–73 cu in).[10]
TheAMC Air-cooled 108 was a 108 cu in (1.8 L) engine built from 1960 to 1963 for use in the lightweightM422 Mighty Mite military vehicle.[11][12] The M422 developed was byAmerican Motors Corporation (AMC) in the United States and specifically designed to be transported by helicopter.[13][14]
Beginning in the 1960s, Ford's European divisions produced two unrelated V4 engines.[9] The first was theFord Taunus V4 engine, produced in Germany from 1962 to 1981. The Taunus was a 60-degree V4 engine with water cooling and overhead valves. Initially designed for use in front-engined cars, it was used in various Ford models and also used in the front-wheel-driveSaab 95,Saab 96, andSaab Sonett models. It was also used in the mid-engineMatra 530 sports car.[15][16][17] The second Ford V4 engine was theFord Essex V4 engine, produced in the United Kingdom from 1965 to 1977 and used in several Ford Corsair, Capri, Consul, Zephyr, and Transit models.[18] Although designed separately from the Taunus engine, the Essex also was a 60-degree V4 with water cooling, overhead valves, and designed for use in front-engined cars/vans.
ThePorsche 919 Hybrid LMP1 racing car used in the 2014–2017 seasons used a 2.0 L (122 cu in) 90-degree turbocharged V4 engine that was mid-mounted.[19]
One of the first motorcycles powered by a V4 engine was the 1931–1935Matchless Silver Hawk built in the United Kingdom.[20] The Silver Hawk used a narrow-angle 16-degree V4 engine with a single cylinder head, pushrod valve actuation, and air cooling.
The 1936–1938Puch P800 was built in Austria for both civilian and military uses.[21] The P800 used a very wide-angle 170-degree V4 engine (therefore being close in appearance to a flat-four engine) with two cylinder heads and air cooling.[22]
V4 engines were used during the mid-to-late 1980s, especially in transverse-engined Honda motorcycles that had a 90-degree V4 engine with water cooling.[23]
The majorityMotoGP manufacturers chose the V4 configuration for their bikes since 2020. These include:
The reasons for this are that compared to traditional firing order inline four engines, V4 engines
Another use of the V4 engine is inoutboard motors for boats. The V4 configuration is popular for outboard marine applications due to its short engine length.
In 1958, both Johnson and Evinrude introduced 70.7 cu in (1,159 cc) V4 outboards rated at 50 hp (37 kW) and weighing 200 lb (91 kg).[24] By 1972, the same basic V4 block was producing more than double the horsepower in stock form because of the experience manufacturers gained from racing.[25] In 1988, Yamaha introduced a 130 hp (97 kW) two-stroke V4 to the US market with what was called "precision blend" oil injection.[26] Most of the outboard motors are usually two-stroke engines with a carburetor.
In 1935, theWisconsin Motor Manufacturing Company began producing petrol (gasoline) V4 engines for industrial, agricultural, and stationary applications,[27] with several farm equipment manufacturers using the Wisconsin V4 engines.[28] In 1950, the largest Wisconsin V4 engine was the VR4D with a displacement of 255 cu in (4.2 L) and a power output of 56.5 hp (42 kW) at 3000 rpm and a peak torque of 162 lb⋅ft (220 N⋅m) at 1250 rpm.[29] The company produced V4 engines until 2019.[30]
In the mid-1940s, Turner Manufacturing in the United Kingdom produced a diesel water-cooled V4 engine for industrial and marine uses. This engine was used in the 1949–1957Turner Yeoman of England tractor.[31]
Mitsubishi Heavy Industries built the4ZF, an air-cooled diesel-powered V4 engine used in theType 73 armored personnel carrier and related Japanese military vehicles since 1973.[32][33]
Media related toV4 engines at Wikimedia Commons
Authority control databases: National |
|---|