Shot is acollective term for small spheres or pellets, often made oflead. These have been projected fromslings since ancient times and were the originalprojectiles for shotguns and are still fired primarily fromshotguns andgrenade launchers, while they are less commonly used inriot guns.Shot shells are also available in manyhandgun calibers in a configuration known as "birdshot", "rat shot", or "snake shot".
Lead shot is also used for a variety of other purposes such as filling cavities with dense material for weight and/or balance. Some versions may be plated with other metals. Lead shot was originally made by pouring molten lead through screens into water, forming what was known as "swan shot", and, later, more economically mass-produced at higher quality using ashot tower. TheBliemeister method has supplanted the shot tower method since the early 1960s.
Producing lead shot from a shot tower was pioneered in the late 18th century by William Watts ofBristol who adapted his house on Redcliffe Hill by adding a three-storey tower and digging a shaft under the house through the caves underneath to achieve the required drop. The process was patented in 1782.[1] The process was later brought above ground through the building ofshot towers.
Molten lead would be dropped from the top of the tower. Like most liquids,surface tension makesdrops of molten lead become near-spherical as they fall. When the tower is high enough, the lead droplets will solidify during the fall and thus retain their spherical form. Water is usually placed at the bottom of the tower, cooling the lead immediately upon landing.
Roundness of manufactured shot produced from the shot tower process is graded by forcing the newly produced shot to roll accurately down inclined planes. Unround shot will naturally roll to the side, for collection. The unround shot was either re-processed in another attempt to make round shot using the shot tower again, or used for applications which did not require round shot (e.g., split shot for fishing).[1]
The hardness of lead shot is controlled through adding variable amounts oftin,antimony andarsenic, formingalloys.[1] This also affects its melting point. Hardness is also controlled by the rate of cooling that is used in manufacturing lead shot.
TheBliemeister method, named after inventor Louis W. Bliemeister of Los Angeles, California, (U.S. patent 2,978,742, dated April 11, 1961) is a process for making lead shot in small sizes from about #7 to about #9. In this process, molten lead is dripped from small orifices and dropped approximately 1 inch (2.5 cm) into a hot liquid, where it is then rolled along an incline and then dropped another 3 feet (90 cm). The temperature of the liquid controls the cooling rate of the lead, while the surface tension of the liquid and the inclined surface(s) work together to bring the small droplets of lead into highly regular balls of lead in spherical form. The size of the lead shot that is produced is determined by the diameter of the orifice used to drip the lead, ranging from approximately 0.018 inches (0.46 mm) for #9 lead shot to about 0.025 inches (0.64 mm) for #6 or #7.0 shot, while also depending on the specific lead alloy that is used.
The roundness of the lead shot depends on the angle of the inclined surfaces as well as the temperature of the liquid coolant. Various coolants have successfully been used, ranging from diesel fuel to antifreeze and water-soluble oil. After the lead shot cools, it is washed, then dried, and small amounts of graphite are finally added to prevent clumping of the lead shot. Lead shot larger than about #5 tends to clump badly when fed through tubes, even when graphite is used, whereas lead shot smaller than about #6 tends not to clump when fed through tubes when graphite is used.
Lead shot dropped quickly into liquid cooling baths when being produced from molten lead is known as "chilled lead shot", in contrast to "soft lead shot" which is produced by molten lead not being dropped as quickly into a liquid cooling bath. The process of rapidly chilling lead shot during its manufacturing process causes the shot to become harder than it would otherwise be if allowed to cool more slowly. Hence, chilled lead shot, being harder and less likely to deform during firing, is preferred by shotgunners for improving shot pattern densities at longer (> 30 yards (27 m)) ranges, whereas soft lead shot, being softer and more likely to deform during firing, is preferred for improving shot pattern densities at very close (< 20 yards (18 m)) ranges as the softer and now deformed shot scatters more quickly when fired. Soft lead shot is also more readily deformed during the firing process by the effects of chokes.
The manufacture of non-lead shot differs from that of lead, withcompression molding used to create some alloys.[2]
._(FindID_93511).jpg)
Shot is available in many sizes for different applications. The size of numbered shot decreases as the number increases. In hunting, some sizes are traditionally used for certain game, or certain shooting situations, although there is overlap and subjective preference. The range at which game is typically encountered and the penetration needed to assure a clean kill must both be considered. Local hunting regulations may also specify a size range for certain game. Shot loses its velocity very quickly due to its lowsectional density andballistic coefficient (seeexternal ballistics). Generally, larger shot carries farther, and does not spread out as much as smaller shot.
Buckshot is a shot formed to larger diameters so that it can be used against bigger game such asdeer,moose, orcaribou. Sizes range in ascending order from size #B (0.17 in, 4.32 mm) to Tri-Ball. It is usually referred by the size, followed by "buck", e.g. "#000" is referred to as "triple-aught buck" in theUnited States or "triple-o buck" in other English speaking countries. Buckshot is traditionallyswaged (in high volume production) or cast (in small volume production). The Bliemeister method does not work for shot larger than #5 (0.12 in, 3.05 mm), and works progressively poorly for shot sizes larger than about #6.
Below is a chart with diameters per pellet and weight for idealized lead spheres for U.S. Standard Designations with a comparison to English shot sizes.[3][4]
| U.S. Size | U.K. Size | Type | Mass (grains) | Pellets per oz (lead) | Pellets per oz (steel) | Diameter (in) | Diameter (mm) |
|---|---|---|---|---|---|---|---|
| 0000 | Buck | 82 | 0.38 | 9.65 | |||
| 000½ | Buck | 76 | 0.37 | 9.4 | |||
| 000 | LG | Buck | 70 | 6 | n/a | 0.36 | 9.14 |
| MG (mould) | Buck | 62.5 | 7 | n/a | 0.347 | 8.81 | |
| 00½ | Buck | 59 | 0.34 | 8.64 | |||
| SG | Buck | 54.7 | 8 | n/a | 0.332 | 8.43 | |
| 00 | Buck | 53.8 | 8 | 0.33 | 8.38 | ||
| 0 | Buck | 49 | 9 | 0.32 | 8.13 | ||
| #1½ | Buck | 44.7 | 0.31 | 7.87 | |||
| #1 | Buck | 40.5 | 10 | 0.30 | 7.62 | ||
| Special SG | Buck | 39.8 | 11 | n/a | 0.298 | 7.57 | |
| #2½ | Buck | 36.6 | 0.29 | 7.37 | |||
| #2 | Buck | 29.4 | 14 | 0.27 | 6.86 | ||
| SSG | Buck | 29.17 | 15 | n/a | 0.269 | 6.83 | |
| #3½ | Buck | 26.3 | 0.26 | 6.6 | |||
| #3 | Buck | 23.4 | 18 | 0.25 | 6.35 | ||
| SSSG | Buck | 21.89 | 20 | n/a | 0.245 | 6.22 | |
| #4 | Buck | 20.7 | 21 | 0.24 | 6.1 | ||
| FF | Waterfowl | 18.2 | 0.23 | 5.84 | |||
| SSSSG | Buck | 17.50 | 25 | n/a | 0.227 | 5.77 | |
| F (or TTT) | Waterfowl | 16.0 | 0.22 | 5.59 | |||
| SSSSSG or AAAA | Buck/ Waterfowl | 14.58 | 30 | n/a | 0.214 | 5.44 | |
| TT | Waterfowl | 13.9 | 0.21 | 5.33 | |||
| AAA | Waterfowl | 12.5 | 35 | n/a | 0.203 | 5.16 | |
| T | Waterfowl | 12.0 | n/a | 53 | 0.20 | 5.08 | |
| AA | Waterfowl | 10.94 | 40 | n/a | 0.194 | 4.93 | |
| BBB | Waterfowl | 10.2 | n/a | 61 | 0.19 | 4.83 | |
| BB | A or BBBB | Waterfowl | 8.75 | 50 | 72 | 0.18 | 4.57 |
| B | BBB | Waterfowl | 7.29 – 7.40 | 60 | 86 | 0.17 | 4.32 |
| BB | Waterfowl | 6.25 | 70 | n/a | 0.161 | 4.09 | |
| #1 | B | Waterfowl | 5.47 | 80 | 103 | 0.154 | 3.91 |
| #2 | Waterfowl | 4.86 | 90 | 125 | 0.15 | 3.81 | |
| #1 | Waterfowl | 4.38 | 100 | n/a | 0.143 | 3.63 | |
| #3 | #2 | Waterfowl | 3.65 | 120 | 154 | 0.135 | 3.43 – 3.56 |
| #4 | Waterfowl | 3.24 | 135 | 192 | 0.13 | 3.3 | |
| #3 | Waterfowl | 3.12 | 140 | n/a | 0.128 | 3.25 | |
| #4½ | Bird | 2.90 | 0.125 | 3.18 | |||
| #5 | #4 | Bird | 2.57 | 170 | 243 | 0.12 | 3.05 |
| #4½ | Bird | 2.19 | 200 | n/a | 0.113 | 2.87 | |
| #6 | #5 | Bird | 1.94 – 1.99 | 220 – 225 | 317 | 0.11 | 2.79 |
| #5½ (m.g.) | Bird | 1.82 | 240 | n/a | 0.107 | 2.72 | |
| #6 | Bird | 1.62 | 270 | n/a | 0.102 | 2.59 | |
| #7 | #6½ | Bird | 1.458 | 300 | 420 | 0.10 | 2.54 |
| #7 | Bird/Clay | 1.29 | 340 | n/a | 0.095 | 2.41 | |
| #7½ | Bird/Clay | 1.25 | 350 | 490 | 0.095 | 2.413 | |
| #8 | Bird/Clay | 1.067 | 410 | 577 | 0.09 | 2.286 | |
| #8½ | #8 | Bird/Clay | 0.97 | 450 | n/a | 0.085 – 0.087 | 2.16 – 2.21 |
| #9 | #9 | Bird/Clay | 0.748 | 580 – 585 | n/a | 0.08 | 2.032 |
| #9½ | Bird/Clay | 0.63 | 0.075 | 1.91 | |||
| #10 | #10 | Pest | 0.51 | 850 | n/a | 0.07 | 1.78 |
| #11 | Pest | 0.42 | 1,040 | n/a | 0.066 | 1.68 | |
| #12 | Pest | 0.35 | 1,250 | n/a | 0.062 | 1.57 | |
| #11 | Pest | 0.32 | 0.06 | 1.52 | |||
| #12 | Pest | 0.183 | 2,385 | n/a | 0.05 | 1.27 | |
| Dust | Pest | 0.17 | 2,600 | n/a | 0.048 | 1.22 | |
| Dust | Pest | 0.10 or less | 0.04 | 1.02 |
When used as a pourable/mouldable weight, lead shot may be left loose, or mixed with a bonding agent such asepoxy to contain and stabilize the pellets after they are poured.
Some applications of lead shot are:
 | The examples and perspective in this sectiondeal primarily with the United States and do not represent aworldwide view of the subject. You mayimprove this section, discuss the issue on thetalk page, or create a new section, as appropriate.(November 2021) (Learn how and when to remove this message) |
Lead shot-related waterfowlpoisonings were first documented in the US in the 1880s;[6] by 1919, the spent lead pellets from waterfowl hunting were positively identified as a major source of deaths of bottom-feeding waterfowl.[7][8][9] Once ingested, stomach acids and mechanical action cause the lead to break down and be absorbed into the body and bloodstream, resulting in death. "If a bird swallows only one pellet, it usually survives, although its immune system and fertility are likely to be affected. Even low concentrations of lead have a negative impact on energy storage, which affects the ability to prepare for migration."[10]Upland game birds such asmourning doves,ring-necked pheasants,wild turkey, northern bobwhitequail andchukars can also ingest lead and thus be poisoned when they feed on seeds.[11]
Lead from spent ammunition also impacts scavenging bird species such as vultures, ravens, eagles and other birds of prey.[12] Foraging studies of the endangeredCalifornian condor have shown that avian scavengers consume lead fragments in gut piles left in the field from harvested big game animals, as well as by the consumption of small game, or "pest animal," carcasses that have been shot with lead-core ammo, but not retrieved. Not all lead exposure in these circumstances leads to immediate mortality, but multiple sub-lethal exposures result in secondary poisoning impacts, which eventually lead to death.[13] Among condors around theGrand Canyon, lead poisoning because of eating lead shot is the most frequently diagnosed cause of death.[13]
Alternatives to lead shot are mandated for use by hunters in certain locations or when hunting migratorywaterfowl andmigratory birds or whenhunting within federal waterfowl production areas, wildlife refuges, or some state wildlife management areas. Shot pellets used inwaterfowl hunting must belead-free in theUnited States,Canada, and in theEuropean Union.[14][15][16]
Lead shot is also banned within an eight-county area in California designated as thecondor's range. As of 2011, thirty-five states prohibited lead shot use in such specially-specified areas when hunting.[17] In an effort to protect the condor, the use of projectiles containing lead has been banned for hunting wild boar, deer, antelope, elk, pronghorn, antelope, coyote, squirrel, and other non-game wildlife in areas of California designated as its habitat range.[18] Thebald eagle has similarly been shown to be affected by lead originating from dead or wounded waterfowl—the requirement to protect this species was one of the biggest factors behind laws being introduced in 1991 by theUnited States Fish and Wildlife Service to ban lead shot in migratory waterfowl hunting.[19]
Hunting restrictions have also banned the use of lead shot while hunting migratory waterfowl in at least 29 countries across by international agreement,[11] for example theAgreement on the Conservation of African-Eurasian Migratory Waterbirds.[10][20] Depending on hunting laws, alternatives to lead shot are mandated for use by hunters in some locations when hunting migratory birds, notably waterfowl. In the US, the restrictions are limited to migratory waterfowl, while Canadian restrictions are wider and apply (with some exceptions) to all migratory birds.[19] The hunting of upland migratory birds such asmourning doves was specifically excluded from the 1991 US restrictions as scientific evidence did not support their contribution to the poisoning of bald eagles.[19] In 1985, Denmark banned the use of lead in wetlands covered by theRamsar Convention, later expanding this restriction to the whole country.[21] The use of lead has been banned for all hunting activities in theNetherlands as of 1992.[22]
TheMissouri Department of Conservation introduced regulations in 2007 in some hunting areas requiring the use of non-toxic shot to protect upland birds.[11] Someclay pigeon ranges in the US have banned the use of lead after elevated levels of lead were found in waterfowl, small birds, mammals and frogs in their vicinity.[11]
Approved alternatives while hunting migratory waterfowl include pellets manufactured fromsteel, tungsten-iron, tungsten-polymer,tungsten-nickel-iron, andbismuth-tin in place of lead shot. In Canada, the United States, the United Kingdom, and many western European countries (France as of 2006), all shot used for hunting migratorywaterfowl must now be non-toxic, and therefore may not contain anylead.
Steel was one of the first widely used lead alternatives that the ammunition industry turned to.[23] But steel is one hundred times harder than lead, with only two-thirds its density, resulting in undesirable ballistic properties compared to lead.[24] Steel shot can be as hard as some barrels, and may therefore damagechokes on older firearms that were designed only for use with softer lead shot.[23] The higher pressures required to compensate for the lower density of steel may exceed the design limits of a barrel.
Within recent years, several companies have created non-toxic shot out ofbismuth,tungsten, or otherelements oralloys with adensity similar to or greater than lead, and with a shot softness that results in ballistic properties that are comparable to lead. These shells provide more consistent patterns and greater range than steel shot. They are also generally safe to use in older shotguns with barrels and chokes not rated for use with steel shot, such as for bismuth and tungsten-polymer (although not tungsten-iron) shot. Unfortunately, all non-lead shot other than steel is far more expensive than lead, which has diminished in its acceptance by hunters.
| Approved shot type | Percent composition by weight |
|---|---|
| Bismuth-tin | 97% bismuth, and 3% tin |
| Iron (steel) | Iron and carbon |
| Iron-tungsten | Any proportion of tungsten, and >1% iron |
| Iron-tungsten-nickel | >1% iron, any proportion of tungsten, and up to 40% nickel |
| Tungsten-bronze | 51.1% tungsten, 44.4% copper, 3.9% tin, and 0.6% iron, or 60% tungsten, 35.1% copper, 3.9% tin, and 1% iron |
| Tungsten-iron-copper-nickel | 40–76% tungsten, 10–37% iron, 9–16% copper, and 5–7% nickel |
| Tungsten-matrix | 95.9% tungsten, 4.1% polymer |
| Tungsten-polymer | 95.5% tungsten, 4.5%Nylon 6 orNylon 11 |
| Tungsten-tin-iron | Any proportions of tungsten and tin, and >1% iron |
| Tungsten-tin-bismuth | Any proportions of tungsten, tin, and bismuth. |
| Tungsten-tin-iron-nickel | 65% tungsten, 21.8% tin, 10.4% iron, and 2.8% nickel |
| Tungsten-iron-polymer | 41.5–95.2% tungsten, 1.5–52.0% iron, and 3.5–8.0%fluoropolymer |
