 Figure 1. Standard male SMA connector: male body (inside threads) with male inner pin | |||
| Type | RF coaxial connector | ||
|---|---|---|---|
| General specifications | |||
| Diameter | Male: 0.312 in (7.9 mm) HEX | ||
| Cable | Coaxial | ||
| Passband | Typically 0–18 GHz, some up to 26.5 GHz | ||
SMA (SubMiniature version A) connectors are semi-precisioncoaxialRF connectors developed in the 1960s as a minimal connectorinterface forcoaxial cable with a screw-type coupling mechanism. The connector has a 50 Ωimpedance.[1] SMA was originally designed for use fromDC (0 Hz) to 12 GHz, however this has been extended over time and variants are available to 18 GHz and 26.5 GHz.[2] There are also mechanically compatible connectors such as the K-connector which operate up to 40 GHz.[3] The SMA connector is most commonly used in microwave systems, hand-held radio and mobile telephone antennas and, more recently, with WiFi antenna systems and USBsoftware-defined radio dongles.[4] It is also commonly used inradio astronomy, particularly at higher frequencies (5 GHz+).
The interface dimensions for SMA connectors are listed in MIL-STD-348.[5] The SMA connector employs a1⁄4 inch diameter, 36-thread-per-inch threaded barrel. The male is equipped with a hex nut measuring5⁄16 inch (0.3125 inch / 7.9 mm) across opposite flats, thus taking the same wrench as a#6SAE hex nut.
Astandard-polarity SMA male connector has a 0.9mm diameter center pin surrounded by barrel with inside threads, and the standard SMA female connector has a center sleeve surrounded by a barrel with outside threads. The centre pin is the same diameter as the centre of RG402 Coax so that connections can be made with no discontinuity, forming the pin from the coax itself. As with most other connectors, thegender assignment corresponds to the innermost electrical component. There are alsoreverse-polarity ("RP") SMA connectors in which the pin and sleeve are swapped so that the "male" RP-SMA has a center sleeve surrounded by an inside-threaded barrel, and the "female" RP-SMA has a center pin and an outside-threaded barrel. See below for a fuller description.[6]
The SMA connector uses apolytetrafluoroethylene (PTFE) dielectric that contacts along the mating plane. Variability in the construction and the mating of the connectors limits the repeatability of the connector impedance. For that reason and that they are just rated for a limited number of connection cycles, an SMA connector is not usually a good choice formetrological applications.[7]
SMA connectors are rated for up to 500 mating cycles,[8] but to achieve this it is necessary to properly torque the connector when making the connection. A5⁄16 inch torque wrench is required for this, set to 3–5 in·lbf (0.3 to 0.6 N·m) for brass, and 7–10 in·lbf (0.8 to 1.1 N·m) for stainless steel connectors. Flats are sometimes also provided on the cable side of the connector assembly so that a second wrench can be used to prevent it from rotating and damaging the joint to the cable. It is also advisable to inspect and clean out loose debris from the internal surfaces with compressed air or a gas duster can before mating.[9][10]
SMA connectors must not be confused with the standard household 75-ohmtype F coax connector (diameters: male7⁄16 inch (11 mm) circular or hex; female3⁄8 inch (9.5 mm) external threads), as there is only about a 2 mm difference overall in the specifications. Type F cannot be mated with SMA connectors without the use of an adapter.
The SMA connector is typically rated formode-free operation from DC to 18 GHz, though some proprietary versions are rated to 26.5 GHz.[11] For performance above this, other SMA-like connectors are used. These include the 3.5 mm connector, rated to 34 GHz, and the 2.92 mm (also known as 2.9 mm, K type, or SMK),[12] good up to 46 GHz. These connectors keep the same outside thread as the SMA, so they can potentially be cross-mated, but the precision connector can be easily damaged when mating with low-grade SMA connectors.[13] The precision versions use an air dielectric with appropriately scaled center conductors.
Beyond 46 GHz, the 2.4 mm, 1.85 mm (also known as V type) and 1.0 mm (also known as W type) connectors exist. These are similar to the SMA connector, but with the geometries incompatibly scaled, and a metric thread to prevent accidental intermating. (But 2.4 mm and 1.85 mm connectors are compatible to each other.) These offer mode-free operation to 50, 65, and 110 GHz respectively.
Reverse-polarity SMA (RP-SMA or RSMA) is a variation of the SMA connector specification that reverses the gender of the interface, as shown in Figures 1 and 2. The term "reverse polarity" here refers only to the gender of the connector's contact pin, not in any way to the signal polarity.
The female RP-SMA connector has the same external housing as a standard or conventional female SMA connector, which consists of an outer shell with the threads on the outside; however, the center receptacle is replaced by a male pin.
Similarly, the RP-SMA male has threads on the inside like a conventional male, but has a center receptacle instead of the male pin in the middle.[14][15] Normal SMA connectors are incompatible with RP-SMA connectors.
Occasionally, the opposite convention is used to designate the gender of an RP connector: In this situation the female connector has a socket (or sleeve) contact and threads on the outside.[16] Users should take care to check drawings and specifications carefully.
| Center pin | Center receptacle | |
|---|---|---|
| Internal thread | SMA male/plug | RP-SMA male/plug |
| External thread | RP-SMA female/jack[17] | SMA female/jack |
Wi-Fi equipment manufacturers have widely used RP-SMA connectors to comply with specific national regulations, such as those from theFCC,[18] which are designed to prevent consumers from connecting antennas that provide additional gain[citation needed] and therefore breach Part 15 compliance. However, by 2000, the FCC regarded the connectors as readily available,[19] though delaying its ruling indefinitely.[20] As of 2018, leading manufacturers such asNetgear andLinksys are still using RP-SMA connectors on their Wi-Fi equipment.[21]
Are all SMA connector the same size?[1]
