 | This article has multiple issues. Please helpimprove it or discuss these issues on thetalk page.(Learn how and when to remove these messages) (Learn how and when to remove this message)
|
SECAM, also writtenSÉCAM (French pronunciation:[sekam],Séquentiel de couleur à mémoire, French forcolor sequential with memory), is ananalog color television system that was used in France, Russia and some other countries or territories of Europe and Africa. It was one of three major analog color television standards, the others beingPAL andNTSC. Like PAL, a SECAM picture is also made up of 625 interlaced lines and is displayed at a rate of 25 frames per second (except SECAM-M). However, due to the way SECAM processes color information, it is not compatible with the PAL video format standard. SECAM video iscomposite video; theluminance (luma, monochrome image) andchrominance (chroma, color applied to the monochrome image) are transmitted together as one signal.
All the countries using SECAM have either converted toDigital Video Broadcasting (DVB), the new pan-European standard for digital television, or are currently in theprocess of conversion. SECAM remained a major standard into the 2000s.
Development of SECAM predates PAL, and began in 1956 by a team led byHenri de France working atCompagnie Française de Télévision (later bought by Thomson, nowTechnicolor). NTSC was considered undesirable in Europe because of its tint problem, requiring an additionalcontrol, which SECAM (and PAL) solved.
Some have argued that the primary motivation for the development of SECAM in France was to protect French television equipment manufacturers.[1] However, incompatibility had started with the earlier unusual decision to adopt positivevideo modulation for 819-line French broadcast signals (only the UK's405-line was similar; widely adopted525- and625-line systems used negative video).
The first proposed system was called SECAM I in 1961, followed by other studies to improve compatibility and image quality,[2] but it was too soon for a wide introduction. A version of SECAM for the French819-line television standard was devised and tested, but never introduced.[3]
Following a pan-European agreement to introduce color TV only on 625-line broadcasts, France had to switch to that system, which happened in 1963 with the introduction of "la deuxième chaîne ORTF"France 2, the second national TV network.
Further improvements during 1963 and 1964 to the standard were called SECAM II[2] and SECAM III, with the latter being presented at the 1965CCIR General Assembly inVienna, and adopted by France and theSoviet Union.[2][4]
Soviet technicians were involved in a separate development of the standard, creating an incompatible variant called NIIR or SECAM IV,[2] which was not deployed. The team was working inMoscow'sTelecentrum. The NIIR designation comes from the name of theNautchno-Issledovatelskiy Institut Radio (NIIR,rus. Научно-Исследовательский Институт Радио), a Soviet research institute involved in the studies.[4] Two standards were developed:Non-linear NIIR,[5] in which a process analogous togamma correction is used, andLinear NIIR[5] orSECAM IV that omits this process.[6] SECAM IV was proposed by France and USSR at the 1966 Oslo CCIR conference[2][4] and demonstrated in London.[7]
Further improvements were SECAM III A, followed by SECAM III B,[2] the system adopted for general use in 1967.
Tested until 1963 on the second French national network "la deuxième chaîne ORTF", the SECAM standard was adopted inFrance and launched on 1 October 1967, now called France 2. A group of four suited men—a presenter (Georges Gorse, Minister of Information) and three contributors to the system's development—were shown standing in a studio. Following a count from 10, at 2:15 pm the black-and-white image switched to color; the presenter then declared "Et voici la couleur !" (fr: And here is color!)[8] In the same year of 1967, CLT ofLebanon became the third television station in the world, afterFrance 2 inFrance and theSoviet Central Television in theSoviet Union, to broadcast in color utilizing the French SECAM technology.[9]
The first color television sets cost 5000francs. Color TV was not very popular initially; only about 1500 people watched the inaugural program in color. A year later in 1968, only 200,000 sets had been sold of an expected million. This pattern was similar to the earlier slow build-up of color television popularity in the US.[improper synthesis?]
In March 1969,East Germany decided to adopt SECAM III B.[2] The adoption of SECAM in Eastern Europe has been attributed toCold War political machinations. According to this explanation, East German political authorities were well aware of West German television's popularity and adopted SECAM rather than the PAL encoding used inWest Germany.[10] This did not hinder mutual reception in black and white, because the underlying TV standards remained essentially the same in both parts of Germany. However,East Germans responded by buying PAL decoders for their SECAM sets. Eventually, the government in East Berlin stopped paying attention to so-called "Republikflucht via Fernsehen", or "defection via television". Later East German–produced TV sets, such as theRFT Chromat, even included a dual standard PAL/SECAM decoder as an option.
Another explanation for the Eastern European adoption of SECAM, led by the Soviet Union, is that the Russians had extremely long distribution lines between broadcasting stations and transmitters.[11] Long co-axial cables or microwave links can cause amplitude and phase variations, which do not affect SECAM signals.
Other countries, notably theUnited Kingdom andItaly, briefly experimented with SECAM before opting for PAL. SECAM was adopted by former French andBelgian colonies inAfrica, as well asGreece,Cyprus, andEastern Bloc countries (except forRomania) and someMiddle Eastern countries.[citation needed]
European efforts during the 1980–90s towards the creation of a unified analog standard, resulting in theMAC standards, still used the sequential color transmission idea of SECAM, with only one of time-compressedU and V components being transmitted on a given line. TheD2-MAC standard enjoyed some short real market deployment, particularly in northern European countries. To some extent, this idea is still present in4:2:0 digital sampling format, which is used by mostdigital video media available to the public. In this case, however, color resolution is halved in both horizontal and vertical directions thus yielding a more symmetrical behavior.
With thefall of communism and following a period when multi-standard TV sets became acommodity in the early 2000s, many Eastern European countries decided to switch to the West German-developed PAL system. Yet SECAM remained in use inRussia,Belarus[12] and the French-speaking African countries. In the late 2000s, SECAM started a process of being phased out and replaced byDVB.
Unlike some other manufacturers, the company where SECAM was invented,Technicolor (known as Thomson until 2010), still sold television sets worldwide under different brands until the company sold its Trademark Licensing operations in 2022; this may be due in part to the legacy of SECAM. Thomson bought the company that developed PAL, Telefunken, and even co-owned theRCA brand – RCA being the creator of NTSC. Thomson also co-authored theATSC standards which are used for Americanhigh-definition television.
Just as with the other color standards adopted for broadcast usage over the world, SECAM is a standard that permits existing monochrome television receivers predating its introduction to continue to be operated as monochrome televisions. Because of this compatibility requirement, color standards added a second signal to the basic monochrome signal, which carries the color information. The color information is calledchrominance or for short, while the black-and-white information is called theluminance or for short. Monochrome television receivers only display luminance, while color receivers process both signals. TheYDbDrcolor space is used to encode the mentioned (luminance) and (red andblue color difference signals that make up chrominance) components.
Additionally, for compatibility, it is required to use no morebandwidth than the monochrome signal alone; the color signal has to be somehow inserted into the monochrome signal, without disturbing it. This insertion is possible because thebandwidth of the monochrome TV signal is generally not fully utilized; the high-frequency portions of the signal, corresponding to fine details in the image, were often not recorded by contemporary video equipment, or not visible on consumer televisions anyway, especially after transmission. This section of thespectrum was thus used to carry color information, at the cost of reducing the possibleresolution.
European monochrome standards were not compatible when SECAM was first being considered. France had introduced an819-line system that used14 MHz of bandwidth (System E), much more than the5 MHz standard used in the UK (System A) or the6 MHz in the US (System M). The closest thing to a standard in Europe at the time was the8 MHz 625-line system (System D), which had originatedGermany and theSoviet Union and quickly became one of the most used systems. An effort to harmonize European broadcasts on the625-line system started in the 1950s and was first implemented inIreland in 1962 (System I).
SECAM thus had the added issue of having to be compatible both with their existing 819-line system as well as their future broadcasts on the 625-line system. As the latter used much less bandwidth, it was this standard that defined the amount of color information that could be carried. In the 8 MHz standard, the signal is split into two parts, the video signal, and the audio signal, each with its owncarrier frequency. For any given channel, one carrier is located 1.25 MHz above thechannel's listed frequency and indicates the location of the luminance portion of the signal. A second carrier is located 6 MHz above the luma carrier, indicating the center of the audio signal.
To add color to the signal, SECAM adds another carrier located 4.4336... MHz above the luma carrier. The chroma signal is centered on this carrier, overlapping the upper part of the luma frequency range. Because the information of mostscan lines differ little from their immediate neighbors, both luma and chroma signals are close to being periodic on thehorizontal scan frequency, and thus theirpower spectra tends to be concentrated on multiples of such frequency. The specific color carrier frequency of SECAM results from carefully choosing it so that thehigher-powered harmonics of the modulated chroma and luma signals are apart from each other and from the sound carrier, thereby minimizingcrosstalk between the three signals.
Thecolor space perceived by humans is three-dimensional because of the nature of theirretinas, which include specific detectors for red, green and blue light. So in addition to luminance, which is already carried by the existing monochrome signal, color requires sending two additional signals. The human retina is more sensitive to green light than to red (3:1) or blue (9:1) light. Because of this, the red () and blue () signals are usually chosen to be sent along luma but with comparably less resolution, to be able to save bandwidth while impacting the perceived image quality the least. (Also, the green signal is on average more closely correlated to luma, making them a poor choice of signal to send separately). To minimize crosstalk with luma and increase compatibility with existing monochrome TV sets, the and signals are usually sent as differences from luma (): and. This way, for an image that contains little color, its color difference signals tend to zero and its color-encoded signal converges to its equivalent monochrome signal.
SECAMcolorimetry was similar to PAL, as defined by the ITU on REC-BT.470.[13] Yet the same document indicates[14] that for existing (at the time of revision, 1998) SECAM sets, the following parameters (similar to the original 1953 color NTSC specification[15]) could be allowed:
| Color space specified by | Year | White point | Primaries | DisplaygammaEOTF | |||||
|---|---|---|---|---|---|---|---|---|---|
| Red | Green | Blue | |||||||
| xʀ | yʀ | xɢ | yɢ | xʙ | yʙ | ||||
| REC-BT.470[16] | 1970 | C | 0.67 | 0.33 | 0.21 | 0.71 | 0.14 | 0.08 | 2.8 |
| EBU 3213-E,ITU-R BT.470/601 (B/G) | 1998 | D65 | 0.64 | 0.33 | 0.29 | 0.6 | 0.15 | 0.06 | 2.8 |
The assumeddisplay gamma was also defined as 2.8.[13]
Luma () is derived from red, green, and blue () gamma pre-corrected primary signals:[13]
and are red and blue color difference signals, used to calculate chrominance:[13]
SECAM differs significantly from the other color systems by the way the color difference signals are carried. InNTSC andPAL, each line carries color difference signals encoded usingquadrature amplitude modulation (QAM). To demodulate such a signal, knowledge of thephase of thecarrier signal is needed. This information is sent along the video signal at the start of every scan line in the form of a short burst of the color carrier itself, called a "colorburst". A phase error during QAM demodulation produces crosstalk between the color difference signals. On NTSC this createsHue andSaturation errors, manually corrected for with a "tint" control on the receiving TV set; while PAL only suffers from Saturation errors. SECAM is free of this problem.
SECAM usesfrequency modulation (FM) to encode chrominance information on the color carrier, which does not require knowledge of the carrier phase to demodulate. However, the simple FM scheme used allows the transmission of only one signal, not the two required for color. To address this, SECAM broadcasts and separately on alternatingscan lines. To produce full color, the color information on one scan line is briefly stored in ananalog delay line adjusted so the signal exits the delay at the precise start of the next line. This allows the television to combine the signal transmitted on one line with the on the next and thereby produce afull color gamut on every line. Because SECAM transmits only one chrominance component at a time, it is free of the color artifacts ("dot crawl") present in NTSC and PAL that result from the combined transmission of color difference signals.
This means that the vertical color resolution of a field is halved compared to NTSC. However, the color signals of all color TV systems of the time were encoded in a narrower band than their luma signals, so color information had lower horizontal resolution compared to luma in all systems. This matches the human retina, which has higher luminance resolution than color resolution. On SECAM, the loss of vertical color resolution makes the color resolution closer to uniform in both axes and has little visual effect. The idea of reducing the vertical color resolution comes from Henri de France, who observed that color information is approximately identical for two successive lines. Because the color information was designed to be a cheap, backwards compatible addition to the monochrome signal, the color signal has a lower bandwidth than the luminance signal, and hence lower horizontal resolution. Fortunately, the human visual system is similar in design: it perceives changes in luminance at a higher resolution than changes in chrominance, so this asymmetry has minimal visual impact. It was therefore also logical to reduce the vertical color resolution. A similar paradox applies to the vertical resolution in television in general: reducing the bandwidth of the video signal will preserve the vertical resolution, even if the image loses sharpness and is smudged in the horizontal direction. Hence, video could be sharper vertically than horizontally. Additionally, transmitting an image with too much vertical detail will cause annoying flicker on interlaced television screens, as small details will only appear on a single line (in one of the two interlaced fields), and hence be refreshed at half the frequency. (This is a consequence ofinterlaced scanning that is obviated byprogressive scan.) Computer-generated text and inserts have to be carefullylow-pass filtered to prevent this.
The color difference signals in SECAM are calculated in theYDbDr color space, which is a scaled version of theYUV color space. This encoding is better suited to the transmission of only one signal at a time.FM modulation of the color information allows SECAM to be completely free of thedot crawl problem commonly encountered with the other analog standards. SECAM transmissions are more robust over longer distances than NTSC or PAL. However, owing to their FM nature, the color signal remains present, although at reduced amplitude, even in monochrome portions of the image, thus being subject to stronger cross color even though color crawl of the PAL type does not exist. Though most of the pattern is removed from PAL and NTSC-encoded signals with acomb filter (designed to segregate the two signals where the luma spectrum may overlap into the spectral space used by the chroma) by modern displays, some can still be left in certain parts of the picture. Such parts are usually sharp edges on the picture, sudden color or brightness changes along the picture or certain repeating patterns, such as a checker board on clothing. FM SECAM is acontinuous spectrum, so unlike PAL and NTSC even a perfect digital comb filter could not entirely separate SECAM colour and luminance signals.
 | This sectiondoes notcite anysources. Please helpimprove this section byadding citations to reliable sources. Unsourced material may be challenged andremoved. Find sources: "SECAM" – news ·newspapers ·books ·scholar ·JSTOR(May 2024) (Learn how and when to remove this message) |
Unlike PAL or NTSC, analog SECAM programming cannot easily be edited in its native analog form. Because it uses frequency modulation, SECAM is not linear with respect to the input image (this is also what protects it against signal distortion), so electrically mixing two (synchronized) SECAM signals does not yield a valid SECAM signal, unlike with analog PAL or NTSC. For this reason, to mix two SECAM signals, they must be demodulated, the demodulated signals mixed, and are remodulated again. Hence,post-production is often done in PAL, or in component formats, with the result encoded or transcoded into SECAM at the point of transmission. Reducing the costs of running television stations is one reason for some countries' switchovers to PAL.
Most TVs currently sold in SECAM countries support both SECAM andPAL, and more recentlycomposite video NTSC as well (though not usuallybroadcast NTSC, that is, they cannot accept a broadcast signal from an antenna). Although the older analog camcorders (VHS,VHS-C) were produced in SECAM versions, none of the8 mm or Hi-band models (S-VHS,S-VHS-C, andHi-8) recorded it directly. Camcorders and VCRs of these standards sold in SECAM countries are internally PAL. The result could be converted back to SECAM in some models; most people buying such expensive equipment would have a multistandard TV set and as such would not need a conversion. Digital camcorders or DVD players (with the exception of some early models) do not accept or output a SECAM analog signal. However, this is of dwindling importance: since 1980 most European domestic video equipment uses French-originatedSCART connectors, allowing the transmission ofRGB signals between devices. This eliminates the legacy of PAL, SECAM, and NTSC color sub carrier standards.
In general, modern professional equipment is now all-digital, and uses component-based digital interconnects such asCCIR 601 to eliminate the need for any analog processing prior to the final modulation of the analog signal for broadcast. However, large installed bases of analog professional equipment still exist, particularly in third world countries.
There are six varieties of SECAM, according to each of thebroadcast system it was used with:
MESECAM is a method of recording SECAM color signals ontoVHS orBetamax video tape. It should not be mistaken for a broadcast standard.
"Native" SECAM recording (marketing term: "SECAM-West") was devised for machines sold for the French (and adjacent countries) market. At a later stage, countries where both PAL and SECAM signals were available developed a cheap method of converting PAL video machines to record SECAM signals, using only the PAL recording circuitry. Although being a workaround, MESECAM is much more widespread than "native" SECAM. It has been the only method of recording SECAM signals to VHS in almost all countries that used SECAM, including the Middle East and all countries in Eastern Europe.
A tape produced by this method is not compatible with "native" SECAM tapes as produced by VCRs in the French market. It will play in black and white only, the color is lost. Most VHS machines advertised as "SECAM capable" outside France can be expected to be of the MESECAM variety only.
On VHS tapes, theluminance signal is recorded FM-encoded (on VHS with reduced bandwidth, onS-VHS with full bandwidth) but the PAL or NTSCchrominance signal is too sensitive to small changes in frequency caused by inevitable small variations in tape speed to be recorded directly. Instead, it is first shifted down to the lower frequency of 630 kHz, and the complex nature of the PAL or NTSC sub-carrier means that the down conversion must be done viaheterodyning to ensure that information is not lost.
The SECAM sub-carriers, which consist of two simple FM signals at 4.41 MHz and 4.25 MHz, do not need this (actually simple) processing. The VHS specification for "native" SECAM recording specifies that they be divided by 4 on recording to give sub carriers of approximately 1.1 MHz and 1.06 MHz, and multiplied by 4 on playback. A true dual-standard PAL and SECAM video recorder therefore requires two color processing circuits, adding to complexity and expense. Since some countries in theMiddle East use PAL and others use SECAM, the region has adopted a shortcut, and uses the PAL mixer-down converter approach for both PAL and SECAM, simplifyingVCR design.
Many PAL VHS recorders have had their analog tuner modified in French-speaking western Switzerland (Switzerland used the PAL-B/G standard while the bordering France used SECAM-L). The original tuner in those PAL recorders allows only PAL-B/G reception. The Swiss importers added a circuit with a specificIC for the French SECAM-L standard, making the tunermulti-standard and allowing the VCR to record SECAM broadcasts in MESECAM. A stamp mentioning "PAL+SECAM" was added to these machines.
Video recorders like Panasonic NV-W1E (AG-W1-P for professional), AG-W3, NV-J700AM, Aiwa HV-MX100, HV-MX1U, Samsung SV-4000W and SV-7000W feature a digital standard conversion circuitry.
A legacy list of SECAM users in 1998 is available onRecommendation ITU-R BT.470-6 - Conventional Television Systems, Appendix 1 to Annex 1,[18] and the list before many OIRT countries migrated to PAL can be found atCCIR Report 624-3 Characteristics of television systems, Annex I.[19]
Below is an updated list of nations that currently authorize the use of the SECAM standard for television broadcasting. It is subject to ongoing changes as nations move to PAL andDVB-T. These migrations are listed separately.
| SECAM users |
|---|
|
Bulgaria[20] (migrated in 1994–1996)
Czechoslovakia (migrated in 1992–1994)[a]
East Germany (switchover on 31 December 1991 afterGerman reunification in 1990)[citation needed]
Estonia[20] (switchover ended in November 1999 with ETV and Kanal 2)[b]
Georgia[20] (migrated in 2000s)
Greece[20] (migrated in 1992)
Hungary[20] (migrated in 1995–1996)
Latvia[20] (migrated in 1997–1999)
Lithuania (migrated in 2002)
Poland (migrated in 1993–1995)
Ukraine (migrated in 1992–1994, simulcast in SECAM until early 2010s)[20][failed verification]Czech Republic, Slovakia, Hungary and the Baltic countries also changed their underlying sound carrier standard on the UHF band from D/K to B/G which is used in most of Western Europe, to facilitate use of imported broadcast equipment, while leaving the D/K standard on VHF. This required viewers to purchase multistandard receivers though. The other countries mentioned kept their existing standards (B/G in the cases of East Germany and Greece, D/K for the rest).[23]
Afghanistan (migrated in the 1990s)[20]
Armenia (migrated in late 1980s)
Azerbaijan[20] (migrated in 2001)
Cambodia[22] (migrated in 1991–1992, from SECAM-M to PAL-B/G)
Iran[22] (reverted in 1998 to PAL-B/G)
Laos (migrated in the 1990s from SECAM-M)
North Korea (migrated in 1993)[20]
Saudi Arabia (simulcast in NTSC, SECAM and PAL—before switching to PAL entirely in the late 1990s or early 2000s)[citation needed]
Vietnam (brief simulcast inNTSC)[d]| Country | Switched to | Switchover completed |
|---|---|---|
 France | DVB-T | 2011-11-2929 November 2011 |
| French Guiana | DVB-T | 2011-11-2929 November 2011 |
 French Polynesia | DVB-T | 2011-11-2929 November 2011 |
| Guadeloupe | DVB-T | 2011-11-2929 November 2011 |
 Kyrgyzstan | DVB-T2 | 20152015 |
 Martinique | DVB-T | 2011-11-2929 November 2011 |
 Mauritius | DVB-T and DVB-T2 | 20132013 |
| Mayotte | DVB-T | 2011-11-2929 November 2011 |
 Monaco | DVB-T | 2011-05-2424 May 2011 |
 Morocco | DVB-T | 20152015 |
 New Caledonia | DVB-T | 2011-11-2929 November 2011 |
| Réunion | DVB-T | 2011-11-2929 November 2011 |
| Saint Barthélemy | DVB-T | 2011-11-2929 November 2011 |
| Saint Pierre and Miquelon | DVB-T | 2011-11-2929 November 2011 |
 Tunisia | DVB-T | 20152015 |
 Uzbekistan | DVB-T and DVB-T2 | 20152015 |
| Wallis and Futuna | DVB-T | 2011-11-2929 November 2011 |
| CAM | |
|---|---|
| CIE | |
| RGB | |
| Y′UV | |
| Other | |
| Color systems and standards | |
For the vision capacities of organisms or machines, see  Color vision. | |
