Apotentiostat is theelectronic hardware required to control athree electrode cell and run mostelectroanalytical experiments. ABipotentiostat andpolypotentiostat are potentiostats capable of controlling two working electrodes and more than two working electrodes, respectively.^[1][2][3][4]

The system functions by maintaining thepotential of theworking electrode at a constant level with respect to thereference electrode by adjusting thecurrent at anauxiliary electrode. The heart of the different potentiostatic electronic circuits is anoperational amplifier (op amp).^[5] It consists of anelectric circuit which is usually described in terms of simpleop amps.

This equipment is fundamental to modernelectrochemical studies usingthree electrode systems for investigations ofreaction mechanisms related toredox chemistry and otherchemical phenomena. The dimensions of the resulting data depend on the experiment. Involtammetry,electric current inamps is plotted againstelectric potential involtage. In abulk electrolysis totalcoulombs passed (totalelectric charge) is plotted against time in seconds even though the experiment measures electric current (amperes) over time. This is done to show that the experiment is approaching an expected number of coulombs.

Most early potentiostats could function independently, providing data output through a physical data trace. Modern potentiostats are designed to interface with apersonal computer and operate through a dedicatedsoftware package. The automated software allows the user rapidly to shift between experiments and experimental conditions. The computer allows data to be stored and analyzed more effectively, rapidly, and accurately than the earlier standalone devices.

A potentiostat is acontrol andmeasuring device. It comprises anelectric circuit which controls the potential across the cell by sensing changes in itsresistance, varying accordingly the current supplied to the system: a higher resistance will result in a decreased current, while a lower resistance will result in an increased current, in order to keep the voltage constant as described byOhm's law.

${\displaystyle R=\frac{E}{I}}$

As a result, the variable systemresistance and the controlled current areinversely proportional

${\displaystyle I_o=\frac{E_c}{R_v}}$

• ${\displaystyle I_o}$ is the output electric current of the potentiostat
• ${\displaystyle E_c}$ is thevoltage that is kept constant
• ${\displaystyle R_v}$ is theelectrical resistance that varies.

Since 1942, when the English electrochemist Archie Hickling (University of Leicester) built the firstthree electrode potentiostat,^[6] substantial progress has been made to improve the instrument. Hickling's device used a third electrode, thereference electrode to control the cell potential automatically. Up until the present day his principle has remained in use. At a glance, a potentiostat measures the potential difference between the working and the reference electrode, applies the current through the counter electrode and measures the current as an${\displaystyle i}$${\displaystyle R}$ voltage drop over a series resistor (${\displaystyle R_{\text{m}}}$ in Fig. 1).

The control amplifier (CA) is responsible for maintaining the voltage between the reference and the working electrode as closely as possible to the voltage of the input source${\displaystyle E_{\text{i}}}$. It adjusts its output to automatically control the cell current so that a condition of equilibrium is satisfied. The theory of operation is best understood using the equations below.

Prior to observing the following equations, one may note that, from an electrical point of view, the electrochemical cell and the current measurement resistor${\displaystyle R_{\text{m}}}$ may be regarded as two impedances (Fig. 2).${\displaystyle Z_1}$ includes${\displaystyle R_{\text{m}}}$ in series with the interfacial impedance of thecounter electrode and the solution resistance between the counter and the reference.${\displaystyle Z_2}$represents the interfacial impedance of the working electrode in series with the solution resistance between the working and the referenceelectrodes.

The role of the control amplifier is to amplify the potential difference between the positive (or noninverting) input and the negative (or inverting) input. This may be translated mathematically into the following equation:

${\displaystyle E_{\text{out}}=A(E^{+}-E^{-})=A(E_{\text{i}}-E_{\text{r}})}$. (1)

where${\displaystyle A}$ is the amplification factor of the CA. At this point the assumption may be made that a negligible amount of current is flowing through the reference electrode. This correlates to physical phenomenon since the reference electrode is connected to a high impedance electrometer. Thus, the cell current may be described in two ways:

${\displaystyle I_{\text{c}}=\frac{E_{\text{out}}}{Z_1+Z_2}}$(2)

and

${\displaystyle I_{\text{c}}=\frac{E_{\text{r}}}{Z_2}}$. (3)

Combining Eqs. (2) and (3) yields Eq. (4):

${\displaystyle E_{\text{r}}=\frac{Z_2}{Z_1+Z_2}{E}_{\text{out}}=\beta E_{\text{out}}}$ (4)

where${\displaystyle \beta }$ is the fraction of the output voltage of the control amplifier returned to its negative input; namely the feedback factor:

${\displaystyle \beta =\frac{Z_2}{Z_1+Z_2}}$.

Combining Eqs. (1) and (4) yields Eq. (6):

${\displaystyle \frac{E_{\text{r}}}{E_{\text{i}}}=\frac{\beta A}{1+\beta A}}$. (6)

When the quantity${\displaystyle \beta }$${\displaystyle A}$ becomes very large with respect to one, Eq. (6) reduces to Eq. (7), which is one of the negative feedback equations:

${\displaystyle E_{\text{i}}=E_{\text{r}}}$. (7)

Eq. (7) proves that the control amplifier works to keep the voltage between the reference and the working close to the input source voltage.

Replacing the CA, a control algorithm can maintain a constant voltage${\displaystyle E_{\text{c}}}$ between the reference electrode and the working electrode.^[7] This algorithm is based on therule of proportion:

${\displaystyle \frac{U_{\text{m}}}{E_{\text{c}}}=\frac{U_{\text{n}}}{E_{\text{SP}}}}$. (8)

• ${\displaystyle U_{\text{m}}}$ is the last measured cell voltage between the working electrode (WE) and the counter electrode (CE).
• ${\displaystyle E_{\text{c}}}$ is the last measured electrochemical potential, i.e. the voltage between the reference electrode and WE to be kept constant.
• ${\displaystyle U_{\text{n}}}$ is the next cell voltage to be set, i.e. the controller output.
• ${\displaystyle E_{\text{SP}}}$ is thesetpoint, i.e. the desired${\displaystyle E_{\text{c}}}$.

If the measurement intervals of Eq. (8) are kept constant, the control algorithm sets the cell voltage${\displaystyle U_{\text{m}}}$ so to keep${\displaystyle E_{\text{c}}}$ as close as possible to the setpoint${\displaystyle E_{\text{SP}}}$. The algorithm requires software-controllable hardware such as adigital multimeter, apower supply, and a double-pole double-throwrelay. The relay is necessary to switch polarity.

In electrochemical experiments the electrodes are the pieces of equipment that comes in immediate contact with theanalyte. For this reason the electrodes are very important for determining the experimental result. The electrode surface may or may not catalyze chemical reactions. The size of the electrodes affects the magnitude of the currents passed which can affect signal to noise. But electrodes are not the only limiting factor for electrochemical experiments, the potentiostat also has a limited range of operation. The following are a few significant features that vary between instruments.

• Electric potential range (measured and applied): while the potential window is mostly based on the solvent window the electronics can also limit the possible range.
• Accuracy in potential (measured and applied): limits of deviations between the actual and reported.
• Range of scan rate: how slow or fast a potential window can be scanned. This is most important for experiments that require high scan rates such as those involvingultramicroelectrodes.
• Sample rate: the rate at which potential or voltage can be accurately sampled. This can be important for experiments that need high scan rates such as those involving ultramicroelectrodes.
• File size: a limiting factor can be the file size limit. This would most likely affect the choice of the potential range swept or the potential sample rate.
• Electric current range (measured and applied): the maximum range over which current can be sampled. Applying large currents is important for experiments that pass a great deal of current like a largebulk electrolysis. Measuring small currents is important for experiments that pass small currents like those involving ultramicroelectrodes.
• Current resolution: determines the operational range of a specific experiment and the bit resolution of that data in the current dimension.
• Accuracy in current (measured and applied): limits of deviations between the actual and reported.
• Number of working channels: how manyworking electrodes can the instrument control. Abipotentiostat is necessary to controlling systems with two working electrodes like arotating ring-disk electrode. Apolypotentiostat may be important for controlling some biological experiments with three or more working electrodes. In conjunction with a Zero Resistance Ammeter per electrode many polarisations can be monitored at the same time in the same cell around the^{[clarification needed]} he couple potential. If the Zero Resistance Ammeters have an offsetting ability, then multiple tests can be achieved at the same time in the same test cell around the individual rest potential of each electrode. Such features can be useful for corrosion monitoring of coated electrodes or segmented but otherwise coupled welds.
• Footprint: potentiostats include small devices of about 20 x 10 x 5 cm weighing well under a kilogram or a simple board that can be installed in a desktop computer. A large bench-top model would be on the order of 50 x 20 x 10 cm and weigh up to or more than 5 kilograms.
• Interface: can the instrument run independently or must it be slaved to a personal computer.
• Sweep generator: can the system apply an analogue sweep or does it use a digital staircase generator as an approximation. If it does use a digital staircase then the resolution of the staircase is important.
• Rotating electrode: can the instrument operate a rotating electrode. This is intrinsic for experiments that require arotating disk electrode orrotating ring-disk electrode.

• Amperostat
• Coulometry
• Electroanalytical method
• Galvanostat
• Operational amplifier
• Polarography
• Potentiometry
• Voltammetry

• "An Inexpensive Field-Portable Programmable Potentiostat".The Chemical Educator.doi:10.1333/s00897050972a. Archived fromthe original on 2006-03-01. Retrieved2008-10-06.
• Staicopoulos, D. N. (1961). "High Current Electronic Potentiostat".Review of Scientific Instruments.32 (2):176–178.Bibcode:1961RScI...32..176S.doi:10.1063/1.1717304.
• Friedman, Elliot S.; Rosenbaum, Miriam A.; Lee, Alexander W.; Lipson, David. A.; Land, Bruce R.; Angenent, Largus T. (2012). "A cost-effective and field-ready potentiostat that poises subsurface electrodes to monitor bacterial respiration".Biosensors and Bioelectronics.32 (1):309–313.doi:10.1016/j.bios.2011.12.013.PMID 22209069.
• W. Colburn, Alex; J. Levey, Katherine; O'Hare, Danny; V. Macpherson, Julie (2021)."Lifting the lid on the potentiostat: a beginner's guide to understanding electrochemical circuitry and practical operation".Physical Chemistry Chemical Physics.23 (14):8100–8117.Bibcode:2021PCCP...23.8100C.doi:10.1039/D1CP00661D.PMID 33875985.

• Genady Ragoisha (webmaster), "Potentiodynamic electrochemical impedance spectroscopy (PDEIS)", Physico-Chemical Research Institute, Belarusian State University. A description of the use of a potentiostat invirtual instrumentation for electrochemical experiments.
• Pierre R. Roberge (Webmaster) "Potentiostat", corrosion-doctors.orgElectrochemistry Dictionary.
• "CheapStat: An Open-Source, “Do-It-Yourself” Potentiostat...", Aaron A. Roweet al., University of California Santa Barbara

• Electroanalytical chemistry devices
• Electronic engineering

• Articles with short description
• Short description matches Wikidata
• Wikipedia articles needing clarification from July 2023