| Lohner Type AA | |
|---|---|
 | |
| Lohner 10.20 with no vertical fin and all moving rudder. | |
| Role | Fighter Type of aircraft |
| National origin | Austria-Hungary |
| Manufacturer | Lohner-Werke |
| Designer | Leopold Bauer |
| First flight | 29 December 1916 |
| Introduction | 5 September 1916.[1] |
| Number built | 4 |
TheLohner Type AA (a.k.a.Lohner 10.20,10.20A,10.20B,111.01,111.02,111.03,Lohner Dr.I andLohner D.I) were a series of prototype fighters built duringWorld War I. The program would eventually be cancelled due to inherent instability concerns of the design.[2]
In 1916 the manufacturing companyLohner-Werke ofVienna was given a contract from theLuftfahrttruppen to design and build a single seat fighter based around the 185 hp (138 kW)Austro-Daimler six-cylinder inline engine.[1]
Work was begun on the first airframe, serial number 111.01, and on 5 September 1916 the Lohner 10.20 was unveiled atAspern.[1] It was a single-baybiplane withequal-span wings andI-type struts. Theempennage incorporated a conventionalhorizontal stabilizer with novertical stabilizer and an abbreviated all-movingrudder.[1] The fuselage was short and deep of laminated wood construction, armed with twinsynchronizedSchwarzlose machine guns.[3]
During taxi trials, insufficientyaw control was reported with a tendency to "swap ends". A larger rudder was installed and the fuselage lengthened from 4.65 to 5.85 m (15 ft 3 in to 19 ft 2 in).[2]The Lohner 10.20 first flew on 29 December 1916 and exhibited poor stability. Further test flights followed and the prototype was severely damaged when it crashed in February 1917.[1]
The fighter was sent back to the Lohner-Werke factory where repairs and extensive modification were completed. Now referred to as the Lohner 10.20A, the fuselage was again lengthened to 6.35 m (20 ft 10 in),[2] the I type struts were replaced with the more common twin struts with wire braces. The tail was completely redesigned with a fixed vertical fin and an even larger rudder. Flight testing of the 10.20A continued until 6 June 1917, when it was totally destroyed in another crash.[1]
The second fighter prototype built was serial number 111.02, called the 10.20B. Tail surfaces were similar to the 10.20A and a deep dorsal fin was added. The I-type wing struts returned, reinforced by inclined V-struts. Its initial flight was at Aspern on 2 June 1917.[1] In August 1917 theLuftfahrttruppen commandeered 10.02B and official trials continued through October when further development of this airframe ended.[1]
The third airframe built was known only as 111.03. The I-type struts were again dropped in favor of the twin struts with wire braces and in an effort to gain directional stability the dorsal fin became even more pronounced. First flown on 28 June 1917, flight testing continued through October.[1] Due to the lackluster performance, further development was halted and theLuftfahrttruppen assigned Lohner-Werke a licence to produce theAviatik (Berg) D.I.[1]
A triplane version of the 111.03 was built as theLohner Dr.I /Type A /111.04.[3]
Data from:Austro-Hungarian Army Aircraft of World War One[3]
Data from Austro-Hungarian Army Aircraft of World War One,[3] The Complete Book of Fighters[4]
General characteristics
Performance
Armament
Aircraft of comparable role, configuration, and era
Related lists
