When the current flowing through the coil changes, the time-varying magnetic field induces anelectromotive force (emf), orvoltage, in the conductor, described byFaraday's law of induction. According toLenz's law, the induced voltage has a polarity (direction) which opposes the change in current that created it. As a result, inductors oppose any changes in current through them.
An inductor is characterized by itsinductance, which is the ratio of the voltage to the rate of change of current. In theInternational System of Units (SI), the unit of inductance is thehenry (H) named for 19th century American scientistJoseph Henry. In the measurement of magnetic circuits, it is equivalent toweber/ampere. Inductors have values that typically range from 1μH (10−6H) to 20H. Many inductors have amagnetic core made of iron orferrite inside the coil, which serves to increase the magnetic field and thus the inductance. Along withcapacitors andresistors, inductors are one of the three passivelinearcircuit elements that make up electronic circuits. Inductors are widely used inalternating current (AC) electronic equipment, particularly inradio equipment. They are used to block AC while allowing DC to pass; inductors designed for this purpose are calledchokes. They are also used inelectronic filters to separate signals of differentfrequencies, and in combination with capacitors to maketuned circuits, used to tune radio and TV receivers.
An electric currentI creates a magnetic fieldB around it
An electric current flowing through aconductor generates a magnetic field surrounding it. The magnetic flux linkage generated by a given current depends on the geometric shape of the circuit. Their ratio defines the inductance.[3][4][5][6] Thus
.
The inductance of a circuit depends on the geometry of the current path as well as themagnetic permeability of nearby materials. An inductor is acomponent consisting of a wire or other conductor shaped to increase the magnetic flux through the circuit, usually in the shape of a coil orhelix, with twoterminals. Winding the wire into acoil increases the number of times themagnetic fluxlines link the circuit, increasing the field and thus the inductance. The more turns, the higher the inductance. The inductance also depends on the shape of the coil, separation of the turns, and many other factors. By adding a "magnetic core" made of aferromagnetic material like iron inside the coil, the magnetizing field from the coil will inducemagnetization in the material, increasing the magnetic flux. The highpermeability of a ferromagnetic core can increase the inductance of a coil by a factor of several thousand over what it would be without it.
Any change in the current through an inductor creates a changing flux, inducing a voltage across the inductor. ByFaraday's law of induction, the voltage induced by any change in magnetic flux through the circuit is given by[6]
.
Reformulating the definition ofL above, we obtain[6]
.
It follows that
ifL is independent of time, current and magnetic flux linkage. Thus, inductance is also a measure of the amount ofelectromotive force (voltage) generated for a given rate of change of current. This is usually taken to be theconstitutive relation (defining equation) of the inductor.
Schematic using current's exit terminal as reference for voltage
Because the induced voltage is positive at the current's entrance terminal, the inductor's current–voltage relationship is often expressed without a negative sign by using the current's exit terminal as the reference point for the voltage at the current's entrance terminal (as labeled in the schematic). The current–voltage relationship is then:
The polarity (direction) of the induced voltage is given byLenz's law, which states that the induced voltage will be such as to oppose the change in current.[7] For example, if the current through an inductor is increasing, the induced potential difference will be positive at the current's entrance point and negative at the exit point, tending to oppose the additional current.[8][9][10] The energy from the external circuit necessary to overcome this potential "hill" is being stored in the magnetic field of the inductor. If the current is decreasing, the induced voltage will be negative at the current's entrance point and positive at the exit point, tending to maintain the current. In this case energy from the magnetic field is being returned to the circuit.
One intuitive explanation as to why a potential difference is induced on a change of current in an inductor goes as follows:
When there is a change in current through an inductor there is a change in the strength of the magnetic field. For example, if the current is increased, the magnetic field increases. This, however, does not come without a price. The magnetic field containspotential energy, and increasing the field strength requires more energy to be stored in the field. This energy comes from the electric current through the inductor. The increase in the magnetic potential energy of the field is provided by a corresponding drop in the electric potential energy of the charges flowing through the windings. This appears as a voltage drop across the windings as long as the current increases. Once the current is no longer increased and is held constant, the energy in the magnetic field is constant and no additional energy must be supplied, so the voltage drop across the windings disappears.
Similarly, if the current through the inductor decreases, the magnetic field strength decreases, and the energy in the magnetic field decreases. This energy is returned to the circuit in the form of an increase in the electrical potential energy of the moving charges, causing a voltage rise across the windings.
Thework done per unit charge on the charges passing through the inductor is. The negative sign indicates that the work is doneagainst the emf, and is not doneby the emf. The current is the charge per unit time passing through the inductor. Therefore, the rate of work done by the charges against the emf, that is the rate of change of energy of the current, is given by
From the constitutive equation for the inductor, so
In a ferromagnetic core inductor, when the magnetic field approaches the level at which the core saturates, the inductance will begin to change, it will be a function of the current. Neglecting losses, theenergy stored by an inductor with a current passing through it is equal to the amount of work required to establish the current through the inductor:
where is the so-called "differential inductance":
In an air core inductor or a ferromagnetic core inductor below saturation, the inductance is constant (and equal to the differential inductance), so the stored energy is
For inductors with magnetic cores, the above equation is only valid forlinear regions of the magnetic flux, at currents below thesaturation level of the inductor, where the inductance is approximately constant. Where this is not the case, the integral form must be used with variable.
In the short-time limit, since the current cannot change instantaneously, the initial current is zero. The equivalent circuit of an inductor immediately after the step is applied is anopen circuit.
As time passes, the current increases at a constant rate with time until the inductor starts to saturate.
In the long-time limit, the transient response of the inductor will die out, the magnetic flux through the inductor will become constant, so no voltage would be induced between the terminals of the inductor. Therefore, assuming the resistance of the windings is negligible, the equivalent circuit of an inductor a long time after the step is applied is ashort circuit.
Theconstitutive equation describes the behavior of anideal inductor with inductance, and withoutresistance,capacitance, or energy dissipation. In practice, inductors do not follow this theoretical model;real inductors have a measurable resistance due to the resistance of the wire and energy losses in the core, andparasitic capacitance between turns of the wire.[11][12]
A real inductor'scapacitive reactance rises with frequency, and at a certain frequency, the inductor will behave as aresonant circuit. Above thisself-resonant frequency, the capacitive reactance is the dominant part of the inductor's impedance. At higher frequencies, resistive losses in the windings increase due to theskin effect andproximity effect.
Inductors with ferromagnetic cores experience additional energy losses due tohysteresis andeddy currents in the core, which increase with frequency. At high currents, magnetic core inductors also show sudden departure from ideal behavior due to nonlinearity caused bymagnetic saturation of the core.
Inductors radiate electromagnetic energy into surrounding space and may absorb electromagnetic emissions from other circuits, resulting in potentialelectromagnetic interference.
An early solid-state electrical switching and amplifying device called asaturable reactor exploits saturation of the core as a means of stopping the inductive transfer of current via the core.
The winding resistance appears as a resistance in series with the inductor; it is referred to as DCR (DC resistance). This resistance dissipates some of the reactive energy. Thequality factor (orQ) of an inductor is the ratio of its inductive reactance to its resistance at a given frequency, and is a measure of its efficiency. The higher the Q factor of the inductor, the closer it approaches the behavior of an ideal inductor. High Q inductors are used with capacitors to make resonant circuits in radio transmitters and receivers. The higher the Q is, the narrower thebandwidth of the resonant circuit.
The Q factor of an inductor is defined as
where is the inductance, is the DC resistance, and the product is the inductive reactance
Q increases linearly with frequency ifL andR are constant. Although they are constant at low frequencies, the parameters vary with frequency. For example, skin effect,proximity effect, and core losses increaseR with frequency; winding capacitance and variations inpermeability with frequency affectL.
At low frequencies and within limits, increasing the number of turnsN improvesQ becauseL varies asN2 whileR varies linearly withN. Similarly increasing the radiusr of an inductor improves (or increases)Q becauseL varies withr2 whileR varies linearly withr. So highQ air core inductors often have large diameters and many turns. Both of those examples assume the diameter of the wire stays the same, so both examples use proportionally more wire. If the total mass of wire is held constant, then there would be no advantage to increasing the number of turns or the radius of the turns because the wire would have to be proportionally thinner.
Using a high permeabilityferromagnetic core can greatly increase the inductance for the same amount of copper, so the core can also increase the Q. Cores however also introduce losses that increase with frequency. The core material is chosen for best results for the frequency band. High Q inductors must avoid saturation; one way is by using a (physically larger) air core inductor. AtVHF or higher frequencies an air core is likely to be used. A well designed air core inductor may have a Q of several hundred.
Example of signal filtering. In this configuration, the inductor blocks AC current, while allowing DC current to pass.Example of signal filtering. In this configuration, the inductordecouples DC current, while allowing AC current to pass.
Inductors are used extensively inanalog circuits and signal processing. Applications range from the use of large inductors in power supplies, which in conjunction with filtercapacitors removeripple which is a multiple of the mains frequency (or the switching frequency for switched-mode power supplies) from the direct current output, to the small inductance of theferrite bead ortorus installed around a cable to preventradio frequency interference from being transmitted down the wire.
Inductors are used as the energy storage device in manyswitched-mode power supplies to produce DC current. The inductor supplies energy to the circuit to keep current flowing during the "off" switching periods and enables topographies where the output voltage is higher than the input voltage.
Atuned circuit, consisting of an inductor connected to acapacitor, acts as aresonator for oscillating current. Tuned circuits are widely used inradio frequency equipment such as radio transmitters and receivers, as narrowbandpass filters to select a single frequency from a composite signal, and inelectronic oscillators to generate sinusoidal signals.
Two (or more) inductors in proximity that have coupled magnetic flux (mutual inductance) form atransformer, which is a fundamental component of everyelectric utilitypower grid. The efficiency of a transformer may decrease as the frequency increases due to eddy currents in the core material and skin effect on the windings. The size of the core can be decreased at higher frequencies. For this reason, aircraft use 400 hertz alternating current rather than the usual 50 or 60 hertz, allowing a great saving in weight from the use of smaller transformers.[13] Transformers enable switched-mode power supplies thatgalvanically isolate the output from the input.
Inductors are also employed inelectrical transmission systems, where they are used to limit switching currents andfault currents. In this field, they are more commonly referred to as reactors.
Inductors have parasitic effects which cause them to depart from ideal behavior. They create and suffer fromelectromagnetic interference (EMI). Their physical size prevents them from being integrated on semiconductor chips. So the use of inductors is declining in modern electronic devices, particularly compact portable devices. Real inductors are increasingly being replaced by active circuits such as thegyrator which cansynthesize inductance using capacitors.
Aferrite "bead"choke, consisting of an encirclingferrite cylinder, suppresses electronic noise in a computer power cord.
Large 50Mvarthree-phase iron-core loading inductor at a utility substation
An inductor usually consists of a coil of conducting material, typically insulatedcopper wire, wrapped around acore either of plastic (to create an air-core inductor) or of aferromagnetic (orferrimagnetic) material; the latter is called an "iron core" inductor. The highpermeability of the ferromagnetic core increases the magnetic field and confines it closely to the inductor, thereby increasing the inductance. Low frequency inductors are constructed like transformers, with cores ofelectrical steellaminated to preventeddy currents. 'Soft'ferrites are widely used for cores aboveaudio frequencies, since they do not cause the large energy losses at high frequencies that ordinary iron alloys do. Inductors come in many shapes. Some inductors have an adjustable core, which enables changing of the inductance. Inductors used to block very high frequencies are sometimes made by stringing a ferrite bead on a wire.
Small inductors can be etched directly onto aprinted circuit board by laying out the trace in aspiral pattern. Some such planar inductors use aplanar core. Small value inductors can also be built onintegrated circuits using the same processes that are used to makeinterconnects.Aluminium interconnect is typically used, laid out in a spiral coil pattern. However, the small dimensions limit the inductance, and it is far more common to use a circuit called agyrator that uses acapacitor and active components to behave similarly to an inductor. Regardless of the design, because of the low inductances and low power dissipation on-die inductors allow, they are currently only commercially used for high frequency RF circuits.
Inductors used in power regulation systems, lighting, and other systems that require low-noise operating conditions, are often partially or fully shielded.[14][15] Intelecommunication circuits employing induction coils and repeating transformers shielding of inductors in close proximity reduces circuit cross-talk.
These coils illustrate high powerhigh Q construction: single layer winding with turns spaced apart to reduceproximity effect losses, made of silver-plated wire or tubing to reduceskin effect losses, supported by narrow insulating strips to reducedielectric losses
The termair core coil describes an inductor that does not use amagnetic core made of a ferromagnetic material. The term refers to coils wound on plastic, ceramic, or other nonmagnetic forms, as well as those that have only air inside the windings. Air core coils have lower inductance than ferromagnetic core coils, but are often used at high frequencies because they are free from energy losses calledcore losses that occur in ferromagnetic cores, which increase with frequency. A side effect that can occur in air core coils in which the winding is not rigidly supported on a form is 'microphony': mechanical vibration of the windings can cause variations in the inductance.
Collection of RF inductors, showing techniques to reduce losses. The three top left and theferrite loopstick or rod antenna,[16][17][18][19] bottom, have basket windings.
Athigh frequencies, particularlyradio frequencies (RF), inductors have higher resistance and other losses. In addition to causing power loss, inresonant circuits this can reduce theQ factor of the circuit, broadening thebandwidth. In RF inductors specialized construction techniques are used to minimize these losses. The losses are due to these effects:
Skin effect: The resistance of a wire tohigh frequency current is higher than its resistance todirect current because ofskin effect.[20][21]: p.141 Due to inducededdy currents, radio frequency alternating current does not penetrate far into the body of a conductor but travels along its surface. For example, at 6 MHz the skin depth of copper wire is about 0.001 inches (25 μm); most of the current is within this depth of the surface. Therefore, in a solid wire, the interior portion of the wire may carry little current, effectively increasing its resistance.
Proximity effect: Another similar effect that also increases the resistance of the wire at high frequencies isproximity effect, which occurs in parallel wires that lie close to each other.[22][21]: p.98 The individual magnetic field of adjacent turns induceseddy currents in the wire of the coil, which causes the current density in the conductor to be displaced away from the adjacent surfaces. Like skin effect, this reduces the effective cross-sectional area of the wire conducting current, increasing its resistance.
Dielectric losses: The high frequency electric field near the conductors in atank coil can cause the motion of polar molecules in nearby insulating materials, dissipating energy as heat. For this reason, coils used for tuned circuits may be suspended in air, supported by narrow plastic or ceramic strips rather than being wound on coil forms.
Parasitic capacitance: The capacitance between individual wire turns of the coil, calledparasitic capacitance, does not cause energy losses but can change the behavior of the coil. Each turn of the coil is at a slightly different potential, so theelectric field between neighboring turns stores charge on the wire, so the coil acts as if it has a capacitor in parallel with it. At a high enough frequency this capacitance can resonate with the inductance of the coil forming atuned circuit, causing the coil to becomeself-resonant.
(left) Spiderweb coil(right) Adjustable ferrite slug-tuned RF coil with basketweave winding and litz wire
To reduce parasitic capacitance and proximity effect,high Q RF coils are constructed to avoid having many turns lying close together, parallel to one another. The windings of RF coils are often limited to a single layer, and the turns are spaced apart. To reduce resistance due to skin effect, in high-power inductors such as those used in transmitters the windings are sometimes made of a metal strip or tubing which has a larger surface area, and the surface is silver-plated.
Basket-weave coils
To reduce proximity effect and parasitic capacitance, multilayer RF coils are wound in patterns in which successive turns are not parallel but crisscrossed at an angle; these are often calledhoneycomb orbasket-weave coils. These are occasionally wound on a vertical insulating supports with dowels or slots, with the wire weaving in and out through the slots.
Spiderweb coils
Another construction technique with similar advantages is flat spiral coils. These are often wound on a flat insulating support with radial spokes or slots, with the wire weaving in and out through the slots; these are calledspiderweb coils. The form has an odd number of slots, so successive turns of the spiral lie on opposite sides of the form, increasing separation.
Litz wire
To reduce skin effect losses, some coils are wound with a special type of radio frequency wire calledlitz wire. Instead of a single solid conductor, litz wire consists of a number of smaller wire strands that carry the current. Unlike ordinarystranded wire, the strands are insulated from each other, to prevent skin effect from forcing the current to the surface, and are twisted or braided together. The twist pattern ensures that each wire strand spends the same amount of its length on the outside of the wire bundle, so skin effect distributes the current equally between the strands, resulting in a larger cross-sectional conduction area than an equivalent single wire.
Axial Inductor
Small inductors for low current and low power are made in molded cases resembling resistors. These may be either plain (phenolic) core or ferrite core. An ohmmeter readily distinguishes them from similar-sized resistors by showing the low resistance of the inductor.
A variety of types of ferrite core inductors and transformers
Ferromagnetic-core or iron-core inductors use a magnetic core made of aferromagnetic orferrimagnetic material such as iron orferrite to increase the inductance. A magnetic core can increase the inductance of a coil by a factor of several thousand, by increasing the magnetic field due to its highermagnetic permeability. However the magnetic properties of the core material cause several side effects which alter the behavior of the inductor and require special construction:
A time-varying current in a ferromagnetic inductor, which causes a time-varying magnetic field in its core, causes energy losses in the core material that are dissipated as heat, due to two processes:
FromFaraday's law of induction, the changing magnetic field can induce circulating loops of electric current in the conductive metal core. The energy in these currents is dissipated as heat in theresistance of the core material. The amount of energy lost increases with the area inside the loop of current.
Changing or reversing the magnetic field in the core also causes losses due to the motion of the tinymagnetic domains it is composed of. The energy loss is proportional to the area of the hysteresis loop in the BH graph of the core material. Materials with lowcoercivity have narrow hysteresis loops and so low hysteresis losses.
Core loss is non-linear with respect to both frequency of magnetic fluctuation and magnetic flux density. Frequency of magnetic fluctuation is the frequency of AC current in the electric circuit; magnetic flux density corresponds to current in the electric circuit. Magnetic fluctuation gives rise to hysteresis, and magnetic flux density causes eddy currents in the core. These nonlinearities are distinguished from the threshold nonlinearity of saturation. Core loss can be approximately modeled withSteinmetz's equation. At low frequencies and over limited frequency spans (maybe a factor of 10), core loss may be treated as a linear function of frequency with minimal error. However, even in the audio range, nonlinear effects of magnetic core inductors are noticeable and of concern.
Saturation
If the current through a magnetic core coil is high enough that the coresaturates, the inductance will fall and current will rise dramatically. This is a nonlinear threshold phenomenon and results in distortion of the signal. For example,audio signals can sufferintermodulation distortion in saturated inductors. To prevent this, inlinear circuits the current through iron core inductors must be limited below the saturation level. Some laminated cores have a narrow air gap in them for this purpose, and powdered iron cores have a distributed air gap. This allows higher levels of magnetic flux and thus higher currents through the inductor before it saturates.[23]
Curie point demagnetization
If the temperature of a ferromagnetic or ferrimagnetic core rises to a specified level, the magnetic domains dissociate, and the material becomes paramagnetic, no longer able to support magnetic flux. The inductance falls and current rises dramatically, similarly to what happens during saturation. The effect is reversible: When the temperature falls below the Curie point, magnetic flux resulting from current in the electric circuit will realign the magnetic domains of the core and its magnetic flux will be restored. The Curie point of ferromagnetic materials (iron alloys) is quite high; iron is highest at 770°C. However, for some ferrimagnetic materials (ceramic iron compounds –ferrites) the Curie point can be close to ambient temperatures (below 100°C).[citation needed]
Low-frequency inductors are often made withlaminated cores to prevent eddy currents, using construction similar totransformers. The core is made of stacks of thin steel sheets orlaminations oriented parallel to the field, with an insulating coating on the surface. The insulation prevents eddy currents between the sheets, so any remaining currents must be within the cross sectional area of the individual laminations, reducing the area of the loop and thus reducing the energy losses greatly. The laminations are made of low-conductivitysilicon steel to further reduce eddy current losses.
For higher frequencies, inductors are made with cores of ferrite. Ferrite is a ceramic ferrimagnetic material that is nonconductive, so eddy currents cannot flow within it. The formulation of ferrite is xxFe2O4 where xx represents various metals. For inductor coressoft ferrites are used, which have low coercivity and thus low hysteresis losses.
Another material is powdered iron cemented with a binder.Medium frequency equipment almost exclusively uses powdered iron cores, and inductors and transformers built for the lowershortwaves are made using either cemented powdered iron orferrites.[citation needed]
Toroidal inductor in the power supply of a wireless router
In an inductor wound on a straight rod-shaped core, themagnetic field lines emerging from one end of the core must pass through the air to re-enter the core at the other end. This reduces the field, because much of the magnetic field path is in air rather than the higher permeability core material and is a source ofelectromagnetic interference. A higher magnetic field and inductance can be achieved by forming the core in a closedmagnetic circuit. The magnetic field lines form closed loops within the core without leaving the core material. The shape often used is atoroidal or doughnut-shaped ferrite core. Because of their symmetry, toroidal cores allow a minimum of the magnetic flux to escape outside the core (calledleakage flux), so they radiate less electromagnetic interference than other shapes. Toroidal core coils are manufactured of various materials, primarily ferrite, powdered iron and laminated cores.[24]
(left) Inductor with a threaded ferrite slug(visible at top) that can be turned to move it into or out of the coil, 4.2 cm high.(right) A variometer used in radio receivers in the 1920s
A "roller coil", an adjustable air-core RF inductor used in thetuned circuits of radio transmitters. One of the contacts to the coil is made by the small grooved wheel, which rides on the wire. Turning the shaft rotates the coil, moving the contact wheel up or down the coil, allowing more or fewer turns of the coil into the circuit, to change the inductance.
Probably the most common type of variable inductor today is one with a moveable ferrite magnetic core, which can be slid or screwed in or out of the coil. Moving the core farther into the coil increases thepermeability, increasing the magnetic field and the inductance. Many inductors used in radio applications (usually less than 100 MHz) use adjustable cores in order to tune such inductors to their desired value, since manufacturing processes have certain tolerances (inaccuracy). Sometimes such cores for frequencies above 100 MHz are made from highly conductive non-magnetic material such as aluminium.[25] They decrease the inductance because the magnetic field must bypass them.
Air core inductors can use sliding contacts or multiple taps to increase or decrease the number of turns included in the circuit, to change the inductance. A type much used in the past but mostly obsolete today has a spring contact that can slide along the bare surface of the windings. The disadvantage of this type is that the contact usuallyshort-circuits one or more turns. These turns act like a single-turn short-circuited transformersecondary winding; the large currents induced in them cause power losses.
A type of continuously variable air core inductor is thevariometer. This consists of two coils with the same number of turns connected in series, one inside the other. The inner coil is mounted on a shaft so its axis can be turned with respect to the outer coil. When the two coils' axes are collinear, with the magnetic fields pointing in the same direction, the fields add and the inductance is maximum. When the inner coil is turned so its axis is at an angle with the outer, the mutual inductance between them is smaller so the total inductance is less. When the inner coil is turned 180° so the coils are collinear with their magnetic fields opposing, the two fields cancel each other and the inductance is very small. This type has the advantage that it is continuously variable over a wide range. It is used inantenna tuners and matching circuits to match low frequency transmitters to their antennas.
Another method to control the inductance without any moving parts requires an additional DC current bias winding which controls the permeability of an easily saturable core material.SeeMagnetic amplifier.
An MF or HF radio choke for tenths of an ampere, and a ferrite bead VHF choke for several amperes.
Achoke is an inductor designed specifically for blocking high-frequency alternating current (AC) in an electrical circuit, while allowing DC or low-frequency signals to pass. Because the inductor restricts or "chokes" the changes in current, this type of inductor is called a choke. It usually consists of a coil of insulated wire wound on a magnetic core, although some consist of a donut-shaped "bead" of ferrite material strung on a wire. Like other inductors, chokes resist changes in current passing through them increasingly with frequency. The difference between chokes and other inductors is that chokes do not require the highQ factor construction techniques that are used to reduce the resistance in inductors used in tuned circuits.
The effect of an inductor in a circuit is to oppose changes in current through it by developing a voltage across it proportional to the rate of change of the current. An ideal inductor would offer no resistance to a constantdirect current; however, onlysuperconducting inductors have truly zeroelectrical resistance.
The relationship between the time-varying voltagev(t) across an inductor with inductanceL and the time-varying currenti(t) passing through it is described by thedifferential equation:
When there is asinusoidalalternating current (AC) through an inductor, a sinusoidal voltage is induced. The amplitude of the voltage is proportional to the product of the amplitude () of the current and the angular frequency () of the current.
In this situation, thephase of the current lags that of the voltage by π/2 (90°). For sinusoids, as the voltage across the inductor goes to its maximum value, the current goes to zero, and as the voltage across the inductor goes to zero, the current through it goes to its maximum value.
If an inductor is connected to a direct current source with valueI via a resistanceR (at least the DCR of the inductor), and then the current source is short-circuited, the differential relationship above shows that the current through the inductor will discharge with anexponential decay:
Reactance is measured in ohms but referred to asimpedance rather than resistance; energy is stored in the magnetic field as current rises and discharged as current falls. Inductive reactance is proportional to frequency. At low frequency the reactance falls; at DC, the inductor behaves as a short circuit. As frequency increases the reactance increases and at a sufficiently high frequency the reactance approaches that of an open circuit.
Inductors in a parallel configuration each have the same potential difference (voltage). To find their total equivalent inductance (Leq):
The current through inductors in series stays the same, but the voltage across each inductor can be different. The sum of the potential differences (voltage) is equal to the total voltage. To find their total inductance:
These simple relationships hold true only when there is no mutual coupling of magnetic fields between individual inductors.
Mutual inductance occurs when the magnetic field of an inductor induces a magnetic field in an adjacent inductor. Mutual induction is the basis of transformer construction.
where M is the maximum mutual inductance possible between 2 inductors and L1 and L2 are the two inductors.In general
as only a fraction of self flux is linked with the other. This fraction is called "Coefficient of flux linkage (K)" or "Coefficient of coupling".
The termC gives theinternal inductance of the wire with skin-effect correction (the imaginary part of the internal impedance of the wire). If ω = 0 (DC) then and as ω approaches ∞,C approaches 0.[29]
^Nagaoka's coefficient (K) is approximately 1 for a coil which is much longer than its diameter and is tightly wound using small gauge wire (so that it approximates a current sheet).
^Wheeler, H.A. (October 1928). "Simple Inductance Formulas for Radio Coils".Proceedings of the Institute of Radio Engineers.16 (10): 1398.doi:10.1109/JRPROC.1928.221309.S2CID51638679.
.jpg)
