Inchemistry,hydrophobicity is thechemical property of amolecule (called ahydrophobe) that is seeminglyrepelled from a mass ofwater.[1] In contrast,hydrophiles are attracted to water.
Hydrophobic molecules tend to benonpolar and, thus, prefer other neutral molecules and nonpolarsolvents. Because water molecules are polar, hydrophobes do notdissolve well among them. Hydrophobic molecules in water often cluster together, formingmicelles. Water on hydrophobic surfaces will exhibit a highcontact angle.
Examples of hydrophobicmolecules include thealkanes,oils,fats, and greasy substances in general. Hydrophobic materials are used for oil removal from water, the management ofoil spills, and chemical separation processes to remove non-polar substances from polar compounds.[2]
The termhydrophobic—which comes from theAncient Greekὑδρόφοβος (hydróphobos), "having a fear of water", constructed from Ancient Greek ὕδωρ (húdōr) 'water' and Ancient Greek φόβος (phóbos) 'fear'[3]—is often used interchangeably withlipophilic, "fat-loving". However, the two terms are not synonymous. While hydrophobic substances are usually lipophilic, there are exceptions, such as thesilicones andfluorocarbons.[4][5]
The hydrophobic interaction is mostly anentropic effect originating from the disruption of the highly dynamichydrogen bonds between molecules of liquid water by the nonpolar solute, causing the water to compensate by forming aclathrate-like cage structure around the non-polar molecules. This structure is more highly ordered than free water molecules due to the water molecules arranging themselves to interact as much as possible with themselves, and thus results in a lower entropic state at the interface. This causes non-polar molecules to clump together to reduce thesurface area exposed to water and thereby increase the entropy of the system.[6][7] Thus, the two immiscible phases (hydrophilic vs. hydrophobic) will change so that their corresponding interfacial area will be minimal. This effect can be visualized in the phenomenon calledphase separation.[citation needed]
Superhydrophobic surfaces, such as the leaves of the lotus plant, are those that are extremely difficult to wet. Thecontact angles of a water droplet exceeds 150°.[8] This is referred to as thelotus effect, and is primarily a chemical property related tointerfacial tension, rather than a chemical property.[9]
In 1805, Thomas Young defined the contact angleθ by analyzing the forces acting on a fluid droplet resting on a solid surface surrounded by a gas.[10]
where
θ can be measured using acontact angle goniometer.
Wenzel determined that when the liquid is in intimate contact with a microstructured surface,θ will change toθW*
wherer is the ratio of the actual area to the projected area.[11] Wenzel's equation shows that microstructuring a surface amplifies the natural tendency of the surface. A hydrophobic surface (one that has an original contact angle greater than 90°) becomes more hydrophobic when microstructured – its new contact angle becomes greater than the original. However, a hydrophilic surface (one that has an original contact angle less than 90°) becomes more hydrophilic when microstructured – its new contact angle becomes less than the original.[12]Cassie and Baxter found that if the liquid is suspended on the tops of microstructures,θ will change toθCB*:
whereφ is the area fraction of the solid that touches the liquid.[13] Liquid in the Cassie–Baxter state is more mobile than in the Wenzel state.[citation needed]
We can predict whether the Wenzel or Cassie–Baxter state should exist by calculating the new contact angle with both equations. By a minimization of free energy argument, the relation that predicted the smaller new contact angle is the state most likely to exist. Stated in mathematical terms, for the Cassie–Baxter state to exist, the following inequality must be true.[14]
A recent alternative criterion for the Cassie–Baxter state asserts that the Cassie–Baxter state exists when the following 2 criteria are met:1) Contact line forces overcome body forces of unsupported droplet weight and 2) The microstructures are tall enough to prevent the liquid that bridges microstructures from touching the base of the microstructures.[15]
A new criterion for the switch between Wenzel and Cassie-Baxter states has been developed recently based on surface roughness andsurface energy.[16] The criterion focuses on the air-trapping capability under liquid droplets on rough surfaces, which could tell whether Wenzel's model or Cassie-Baxter's model should be used for certain combination of surface roughness and energy.[citation needed]
Contact angle is a measure of static hydrophobicity, andcontact angle hysteresis and slide angle are dynamic measures. Contact angle hysteresis is a phenomenon that characterizes surface heterogeneity.[17] When a pipette injects a liquid onto a solid, the liquid will form some contact angle. As the pipette injects more liquid, the droplet will increase in volume, the contact angle will increase, but its three-phase boundary will remain stationary until it suddenly advances outward. The contact angle the droplet had immediately before advancing outward is termed the advancing contact angle. The receding contact angle is now measured by pumping the liquid back out of the droplet. The droplet will decrease in volume, the contact angle will decrease, but its three-phase boundary will remain stationary until it suddenly recedes inward. The contact angle the droplet had immediately before receding inward is termed the receding contact angle. The difference between advancing and receding contact angles is termed contact angle hysteresis and can be used to characterize surface heterogeneity, roughness, and mobility.[18] Surfaces that are not homogeneous will have domains that impede motion of the contact line. The slide angle is another dynamic measure of hydrophobicity and is measured by depositing a droplet on a surface and tilting the surface until the droplet begins to slide. In general, liquids in the Cassie–Baxter state exhibit lower slide angles andcontact angle hysteresis than those in the Wenzel state.[citation needed]
Dettre and Johnson discovered in 1964 that the superhydrophobiclotus effect phenomenon was related to rough hydrophobic surfaces, and they developed a theoretical model based on experiments with glass beads coated with paraffin or TFE telomer. The self-cleaning property of superhydrophobic micro-nanostructured surfaces was reported in 1977.[19] Perfluoroalkyl, perfluoropolyether, and RF plasma -formed superhydrophobic materials were developed, used forelectrowetting and commercialized for bio-medical applications between 1986 and 1995.[20][21][22][23] Other technology and applications have emerged since the mid-1990s.[24] A durable superhydrophobic hierarchical composition, applied in one or two steps, was disclosed in 2002 comprising nano-sized particles ≤ 100 nanometers overlaying a surface having micrometer-sized features or particles ≤ 100 micrometers. The larger particles were observed to protect the smaller particles from mechanical abrasion.[25]
In recent research, superhydrophobicity has been reported by allowing alkylketenedimer (AKD) to solidify into a nanostructured fractal surface.[26] Many papers have since presented fabrication methods for producing superhydrophobic surfaces including particle deposition,[27] sol-gel techniques,[28] plasma treatments,[29] vapor deposition,[27] and casting techniques.[30] Current opportunity for research impact lies mainly in fundamental research and practical manufacturing.[31] Debates have recently emerged concerning the applicability of the Wenzel and Cassie–Baxter models. In an experiment designed to challenge the surface energy perspective of the Wenzel and Cassie–Baxter model and promote a contact line perspective, water drops were placed on a smooth hydrophobic spot in a rough hydrophobic field, a rough hydrophobic spot in a smooth hydrophobic field, and a hydrophilic spot in a hydrophobic field.[32] Experiments showed that the surface chemistry and geometry at the contact line affected the contact angle andcontact angle hysteresis, but the surface area inside the contact line had no effect. An argument that increased jaggedness in the contact line enhances droplet mobility has also been proposed.[33]
Many hydrophobic materials found in nature rely onCassie's law and arebiphasic on the submicrometer level with one component air. The lotus effect is based on this principle.Inspired by it, many functional superhydrophobic surfaces have been prepared.[34]
An example of abionic orbiomimetic superhydrophobic material innanotechnology isnanopin film.[citation needed]
One study presents avanadium pentoxide surface that switches reversibly between superhydrophobicity andsuperhydrophilicity under the influence of UV radiation.[35] According to the study, any surface can be modified to this effect by application of asuspension of rose-like V2O5 particles, for instance with aninkjet printer. Once again hydrophobicity is induced by interlaminar air pockets (separated by 2.1nm distances). The UV effect is also explained. UV light createselectron-hole pairs, with the holes reacting with lattice oxygen, creating surface oxygen vacancies, while the electrons reduce V5+ to V3+. The oxygen vacancies are met by water, and it is this water absorbency by the vanadium surface that makes it hydrophilic. By extended storage in the dark, water is replaced by oxygen andhydrophilicity is once again lost.[citation needed]
A significant majority of hydrophobic surfaces have their hydrophobic properties imparted by structural or chemical modification of a surface of a bulk material, through either coatings or surface treatments. That is to say, the presence of molecular species (usually organic) or structural features results in high contact angles of water. In recent years,rare earth oxides have been shown to possess intrinsic hydrophobicity.[36] The intrinsic hydrophobicity of rare earth oxides depends on surface orientation and oxygen vacancy levels, and is naturally more robust than coatings or surface treatments, having potential applications in condensers and catalysts that can operate at high temperatures or corrosive environments.[37]
Hydrophobic concrete has been produced since the mid-20th century.[citation needed]
Active recent research on superhydrophobic materials might eventually lead to more industrial applications.[38]
A simple routine of coating cotton fabric withsilica[39] ortitania[40] particles bysol-gel technique has been reported, which protects the fabric from UV light and makes it superhydrophobic.
An efficient routine has been reported for makingpolyethylene superhydrophobic and thus self-cleaning.[41] 99% of dirt on such a surface is easily washed away.
Patterned superhydrophobic surfaces also have promise for lab-on-a-chip microfluidic devices and can drastically improve surface-based bioanalysis.[42]
In pharmaceuticals, hydrophobicity of pharmaceutical blends affects important quality attributes of final products, such asdrug dissolution andhardness.[43] Methods have been developed to measure the hydrophobicity of pharmaceutical materials.[44][45]
The development of hydrophobicpassive daytime radiative cooling (PDRC) surfaces, whose effectiveness atsolar reflectance andthermal emittance is predicated on their cleanliness, has improved the "self-cleaning" of these surfaces. Scalable and sustainable hydrophobic PDRCs that avoidVOCs have further been developed.[46]
{{cite journal}}:Cite journal requires|journal= (help)