Theflicker fusion threshold, also known ascritical flicker frequency orflicker fusion rate, is the frequency at which aflickering light appears steady to the average human observer. It is a concept studied invision science, more specifically in thepsychophysics ofvisual perception. A traditional term for "flicker fusion" is "persistence of vision", but this has also been used to describepositive afterimages ormotion blur. Although flicker can be detected for many waveforms representing time-variant fluctuations of intensity, it is conventionally, and most easily, studied in terms of sinusoidal modulation of intensity.
There are seven parameters that determine the ability to detect the flicker:
As long as the modulation frequency is kept above the fusion threshold, the perceived intensity can be changed by changing the relative periods of light and darkness. One can prolong the dark periods and thus darken the image; therefore the effective and average brightness are equal. This is known as theTalbot-Plateau law.[2] Like allpsychophysical thresholds, the flicker fusion threshold is a statistical rather than an absolute quantity. There is a range of frequencies within which flicker sometimes will be seen and sometimes will not be seen, and the threshold is the frequency at which flicker is detected on 50% of trials.
Different points in the visual system have very different critical flicker fusion rate (CFF) sensitivities; the overall threshold frequency for perception cannot exceed the slowest of these for a given modulation amplitude. Each cell type integrates signals differently. For example,rod photoreceptor cells, which are exquisitely sensitive and capable of single-photon detection, are very sluggish, with time constants in mammals of about 200 ms.Cones, in contrast, while having much lower intensity sensitivity, have much better time resolution than rods do. For both rod- and cone-mediated vision, the fusion frequency increases as a function of illumination intensity, until it reaches a plateau corresponding to the maximal time resolution for each type of vision. The maximal fusion frequency for rod-mediated vision reaches a plateau at about 15 hertz (Hz), whereas cones reach a plateau, observable only at very high illumination intensities, of about 60 Hz.[3][4]
In addition to increasing with average illumination intensity, the fusion frequency also increases with the extent of modulation (the maximal relative decrease in light intensity presented); for each frequency and average illumination, there is a characteristic modulation threshold, below which the flicker cannot be detected, and for each modulation depth and average illumination, there is a characteristic frequency threshold. These values vary with the wavelength of illumination, because of the wavelength dependence of photoreceptor sensitivity, and they vary with the position of the illumination within the retina, because of the concentration of cones in central regions including thefovea and themacula, and the dominance of rods in the peripheral regions of the retina.
Flicker fusion is important in all technologies for presenting moving images, nearly all of which depend on presenting a rapid succession of static images (e.g. theframes in a cinema film, TV show, or adigital video file). If theframe rate falls below the flicker fusion threshold for the given viewing conditions, flicker will be apparent to the observer, and movements of objects on the film will appear jerky. For the purposes of presenting moving images, the human flicker fusion threshold is usually taken between 60 and 90 Hz, though in certain cases it can be higher by an order of magnitude.[5] In practice, movies since thesilent era are recorded at 24 frames per second and displayed by interrupting each frame two or three times for a flicker of 48 or 72 Hz. Television typically originates at 50 or 60 frames or interlacedfields per second.
The flicker fusion threshold does not prevent indirect detection of a high frame rate, such as the phantom array effect orwagon-wheel effect, as human-visible side effects of a finite frame rate were still seen on an experimental 480 Hz display.[6]
Cathode-ray tube (CRT) displays typically operated at avertical scan rate of 60 Hz, the same asSDTV content they displayed, which resulted in noticeable flicker. The same was true of other impulsed technologies such asplasma displays. Some systems could increase refresh rate to higher values such as 72, 75, 100, or 120 Hz to ease this problem, though even if the faster refresh is an integer multiple of the source material framerate to eliminatejudder, without higher framerate source material this causes the perception of duplicate images.[7] Any flicker onsample and hold technologies such asLCD orOLED, is unrelated to refresh rate and far less conspicuous, instead coming from incidental design compromises such asfluorescent backlights,PWM dimming, ortemporal dithering, all of which are eliminated on some devices that do not flicker at all. Because of the resultingdisplay motion blur inherent to sample and hold screens, in applications where accuratemotion perception is prioritized over user fatigue, the correct type of flicker can be reintroduced through techniques such as backlight strobing or black frame insertion.
Flicker is also important in the field of domestic (alternating current) lighting, where noticeable flicker can be caused by varying electrical loads, and hence can be very disturbing to electric utility customers. Most electricity providers have maximum flicker limits that they try to meet for domestic customers.
Fluorescent lamps using conventionalmagnetic ballasts flicker at twice the supply frequency. Electronic ballasts do not produce light flicker since the phosphor persistence is longer than a half cycle of the higher operation frequency of 20 kHz. The 100–120 Hz flicker produced by magnetic ballasts is associated with headaches and eyestrain.[8]Individuals with high critical flicker fusion threshold are particularly affected by light from fluorescent fixtures that have magnetic ballasts: their EEG alpha waves are markedly attenuated and they perform office tasks with greater speed and decreased accuracy. The problems are not observed with electronic ballasts.[9] Ordinary people have better reading performance using high-frequency (20–60 kHz) electronic ballasts than magnetic ballasts,[10] although the effect was small except at high contrast ratio.
The flicker of fluorescent lamps, even with magnetic ballasts, is so rapid that it is unlikely to present a hazard to individuals withepilepsy.[11] Early studies suspected a relationship between the flickering of fluorescent lamps with magnetic ballasts andrepetitive movement inautistic children.[12] However, these studies had interpretive problems[13] and have not been replicated.
LED lamps generally do not benefit from flicker attenuation through phosphor persistence, the notable exception being white LEDs. Flicker at frequencies as high as 2000 Hz (2 kHz) can be perceived by humans duringsaccades,[14] and frequencies above 3000 Hz (3 kHz) have been recommended to avoid human biological effects.[15]
In some cases, it is possible to see flicker at rates beyond 2000 Hz (2 kHz) in the case of high-speed eye movements (saccades) or object motion, via the "phantom array" effect.[16][17] Fast-moving flickering objects zooming across view (either by object motion, or by eye motion such as rolling eyes), can cause a dotted or multicolored blur instead of a continuous blur, as if they were multiple objects.[18]Stroboscopes are sometimes used to induce this effect intentionally. Some special effects, such as certain kinds ofelectronic glowsticks commonly seen at outdoor events, have the appearance of a solid color when motionless but produce a multicolored or dotted blur when waved about in motion. These are typically LED-based glow sticks. The variation of the duty cycle upon the LED(s), results in usage of less power while by the properties of flicker fusion having the direct effect of varying the brightness.[citation needed] When moved, if the frequency of duty cycle of the driven LED(s) is below the flicker fusion threshold timing differences between the on/off state of the LED(s) becomes evident, and the color(s) appear as evenly spaced points in the peripheral vision.
A related phenomenon is therainbow effect, where different colors are displayed in different places on the screen for the same object due to fast motion.
Flicker is the perception of visual fluctuations in intensity and unsteadiness in the presence of a light stimulus, that is seen by a static observer within a static environment. Flicker that is visible to the human eye will operate at a frequency of up to 80 Hz.[19]
Thestroboscopic effect is sometimes used to "stop motion" or to study small differences in repetitive motions. The stroboscopic effect refers to the phenomenon that occurs when there is a change in perception of motion, caused by a light stimulus that is seen by a static observer within a dynamic environment. The stroboscopic effect will typically occur within a frequency range between 80 and 2000 Hz,[19] though can go well beyond to 10,000 Hz for a percentage of population.[20]
Phantom array, also known as theghosting effect, occurs when there is a change in perception of shapes and spatial positions of objects. The phenomenon is caused by a light stimulus in combination with rapid eye movements (saccades) of an observer in a static environment. Similar to the stroboscopic effect, the phantom effect will also occur at similar frequency ranges. The mouse arrow is a common example[21] of the phantom array effect.
The flicker fusion threshold also varies betweenspecies. A 2014 survey of the critical fusion frequency in animals found the lowest value (6.7 Hz) in the cane toad (Bufo marinus) and the highest value (400 Hz) in the black fire beetle (Melanophila acuminate).[22] Estimates for different species of bird vary from 40 Hz to 140 Hz, with higher values tending to be associated with faster-moving species.[23] Many mammals have a higher proportion of rods in their retina than humans do, and it is likely that they would also have higher flicker fusion thresholds. This has been confirmed in dogs.[24]
If artificial lighting is perceived as flickering by some animals, the aversive effect might be an issue for animal welfare and conservation. However, those animals most liable to perceive flicker tend to be diurnal species active in bright light, and thus least likely to be exposed to artificial lighting outside of captivity.[22] Size and metabolic rate are two further factors associated with the variation in flicker fusion thresholds: small animals with a high metabolic rate tend to have high values.[25][26]
{{cite web}}: CS1 maint: postscript (link)(Wayback Machine copies)